advertisement
6.5.18 E-mail
1. E-mail function on or off.
2. Alarm mask for e-mail notifications (see chapter "6.5.17 Alarm mask")
Changes are stored or reset on the overlying menu page “MAIL
CONFIGURATION“.
3. IP address of the mail server e.g. 10.249.34.5
ENTER without entering an address will delete the entry.
4. Mail server port (often 25)
5.-6. Destination e-mail address.
ENTER without entering an address will delete the entry.
7. Reply address (e.g. support, administrator...)
ENTER without entering an address will delete the entry.
8. Sender address (important for authentication through the mail server)
ENTER without entering an address will delete the entry.
Press ENTER to change to page 2.
Notice:
Configuration of a gateway is required for sending e-mails (see chapter
"6.5.22 Network"). This can be set via DHCP or manually.
© MOBATIME 45 / 108 801053.02
E-mail configuration page 2:
11. Authentication mode:
0=off (sender e-mail address used for authentication)
1=auto (tries CRAM-MD5, LOGIN- PLAIN in this sequence)
2=PLAIN
3=LOGIN
4=CRAM-MD5
12. User name (only for authentication mode 1-4)
13. Password (only for authentication mode 1-4)
Press ENTER to change to page 1.
Format of an error message via E-mail:
Event <Alarm 03 set: Power failure 1>
Time <11:26:45 10.01.07>
Hostname <DTS4148 (10.241.0.30)>
© MOBATIME 46 / 108 801053.02
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - Safety
- - Maintenance
- - General Information: Introduction
- - Displays
- - Installation
- - Operation
- - Updates
- - Time administration
- 4 Power supply alternatives
- 5 Connection diagrams
- 9 Time zone table
- 12 Alarm list
- 14 Troubleshooting
- 16 Serial Telegrams
- 21 Copyright Notice
- 22 Parameters
- 27 Technical data
- 30 Index
- 32 Connection table (to fill in)
- 6 Safety
- 6 Safety instructions
- 6 Instruction Manual
- 6 Intended Use
- 7 Observe operating safety!
- 7 Consider the installation site!
- 7 compatibility!
- 8 Maintenance
- 8 Troubleshooting: Repairs
- 8 Cleaning
- 8 Disposing
- 9 General Information: Introduction
- 9 Scope of Delivery
- 9 Technical Data
- 9 Device Description in this Manual
- 9 Introduction
- 10 Device types
- 10 DTS Distributed Time System
- 10 MOBA-NMS - Network Management System
- 11 Overview of the main functions
- 12 Device management
- 13 Displays
- 13 LED displays front side
- 13 LED indication back side
- 14 Display
- 15 Installation
- 15 Connections
- 15 Initial configuration
- 15 Firmware
- 15 Basic settings (factory settings)
- 16 Operation
- 16 General
- 16 Telnet
- 17 Menu structure
- 18 MOBA-NMS operation
- 19 Main menu
- 20 Status menu
- 22 Time information and status
- 23 Time source information
- 24 Configuration menu
- 25 Lines
- 25 DCF – output
- 26 DCF / Pulse / Frequency output
- 27 Serial interface
- 29 IRIG / AFNOR / DCF-FSK Output
- 30 NTP slave clocks / time zone server
- 32 SINEC
- 32 Time handling
- 33 Time source
- 34 Time adjustment / Time-keeping
- 35 Redundant operation
- 36 NTP server
- 40 Manual time set / Leap second
- 41 PTP Server
- 43 Alarms
- 43 Alarm relay
- 44 Alarm mask
- 45 E-mail
- 47 SNMP traps
- 49 Alarm input
- 50 General settings
- 51 Network
- 53 Services (network services FTP, telnet, SSH...)
- 55 SNMP V1 / V2c
- 56 SNMP V
- 59 Time zone selection
- 60 Maintenance menu
- 61 Updates
- 61 Updating images with MOBA-NMS
- 61 Updating images with FTP
- 62 Updating images via USB
- 64 FTP connection
- 64 SFTP connection
- 65 SCP connection
- 65 Save Configuration externally
- 66 4148.grandmaster
- 67 Time administration
- 67 Concept of time administration
- 68 Time acceptance
- 68 (DCF or GPS)
- 69 IRIG-B12x source
- 69 Time acceptance from NTP
- 69 NTP as backup
- 69 Time server
- 70 Time accuracy, time-keeping
- 70 Leap second
- 70 NTP Authentication
- 70 NTP symmetric keys
- 71 NTP Autokey
- 73 4148.grandmasters
- 75 General
- 76 Device configuration with SNMP
- 76 DTS subagent SNMP notification
- 76 Startup [dts4148StartUp]
- 76 Shutdown [dts4148Shutdown]
- 77 Status changed [dts4148StatusChanged]
- 77 [dts4148ConfigChanged]
- 78 Alive Notification [dts4148Alive]
- 78 Alarm Notification [dts4148Alarm]
- 79 Power supply alternatives