advertisement
Remote control
!
Battery installation
1 Open the battery cover.
2 Insert the supplied batteries according to the direction indicated in the battery compartment.
When inserting or removing the batteries, push them toward the battery terminals.
3 Close the cover.
Precautions for battery use:
" Replace all old batteries with new ones at the same time.
" Do not mix old and new batteries.
" Remove the batteries if the unit will not be used for long periods of time. This will prevent potential damage due to battery leakage.
Caution:
"
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
" Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
" Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
" Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth.
" Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
" Keep the remote control away from moisture, heat, shock, and vibrations.
!
Test of the remote control
Point the remote control directly at the remote sensor on the main unit.
The remote control can be used within the range shown on the right.
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy your system.
Note:
The remote control may not work while the disc door is open. Move closer to the main unit, or aim the remote control from different angles.
Main unit
Remote sensor
8" - 20'
(0.2 m - 6 m)
AC power connection
!
Connecting the AC power cord
After checking all the connections have been made correctly, plug the AC power cord of this unit into the AC outlet.
AC outlet
(AC 120 V, 60 Hz)
Note:
Unplug the AC power cord from the AC outlet if the unit will not be in use for a prolonged period of time.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
!
To turn the power on
Press the ON/STAND-BY button.
If the power does not turn on, check if the power cords are plugged in properly.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
Notes:
"
After the unit enters the power stand-by mode, wait a few seconds to turn on again.
"
You can also use the ON/STAND-BY button on the remote control.
Main unit
SD-HX500
ENGLISH
04/2/4 SD_HX500_SEC_SECL_E1.fm
E-16
TINSKA015AWZZ
N
P
I
V
E
E
F
S
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Accessories
- 8 Precautions
- 13 Controls and indicators
- 15 Description of discs
- 16 System installation
- 17 System connections
- 19 Speaker connection
- 19 Antenna connection
- 20 TV connection
- 21 Remote control
- 21 AC power connection
- 22 Setting the clock
- 23 General control
- 25 Playing a disc
- 26 To locate the beginning of a chapter (track) (skip)
- 26 Fast forward/Fast reverse (search)
- 27 To start playback from the desired point (direct play)
- 28 To play in the desired order (programmed play)
- 29 To play repeatedly (repeat play)
- 29 To play the contents between the specified points repeatedly (A-B repeat)
- 30 Still picture/Frame advance
- 30 Slow-motion play
- 30 Resume play
- 31 To change the angle
- 31 To zoom images (zoom)
- 32 To select a title from the top menu of the disc
- 32 To select a subtitle or audio language from the disc menu
- 32 To change the subtitle language
- 33 To change the audio language (audio output)
- 33 Brightening the image (Gamma correction)
- 33 Sharpening the image (Super picture)
- 34 To change the display on TV screen
- 34 To change the display on the unit
- 35 Switching elapsed time
- 35 Switching playing time
- 35 To change the setting on the playback control screen
- 36 Playing a DVD-Audio disc
- 37 Playing hybrid SACD sound
- 38 To play in random order (random play)
- 39 Playing an MP3 disc
- 40 Listening to the radio
- 42 Listening to the memorized station
- 46 Enjoying surround sound (sound mode)
- 50 Changing the initial setting of DVD
- 54 Changing the default settings of the amplifier
- 55 Timer playback
- 56 Setting the timer
- 57 Operations after setting the timer
- 58 Sleep timer
- 60 Operating the connected TV
- 61 Storing volume, surround or amplifier settings
- 63 Mounting the unit on the wall
- 66 Connecting other equipment
- 67 Maintenance
- 67 Error indicators and warnings
- 69 Troubleshooting chart
- 70 Language code list for disc language
- 71 Specifications