advertisement
3.1.2 System
System settings include the 9 parts: Basic Setup, Time, Serial Port, Admin Access, System Log, Config Management,
Update, Reboot and Logout.
(1) Basic Setup
Parameters Name
Language
Router Name
Host Name
Description
Choose language of configuration web
Set name of InRouter
Name the device/PC linked with IR700
Chinese
Router
Router
Default Example
English
My InRouter
My InRouter
(2) Time
(3) Serial Port
Router Time
PC Time
Name Description
Display router time
Display PC time (or the time of device linked with router)
Set time zone Time Zone
Custom TZ string Set the string of time zone of Router
Time Update Interval Auto Update Time
NTP Time Servers (after enable the Setting for NTP Time server. (Three at the most)
Auto Update Time)
Custom
CST-8
Disabled pool.ntp.org
Default
1970-1-1 8:00:00
Name
Baud Rate
Data Bit
Parity
Stop Bit
Hardware Flow Control
Software Flow Control
Description
Serial baud rate
Serial data bits
Set parity bit of serial data.
Set stop bit of serial data.
Enable Hardware Flow Control
Enable Software Flow Control
19200
8
None
1
Disable
Disable
Default
(4) Admin Access
Name
Username
Old Password
New Password
Confirm New Password
Description
Username/Password
Username for configuration web login
To change the password, you need to input the old one
Input new password
Input the new password again
Enable
Service Type
Local Access
Select to enable
Management
HTTP/HTTPS/TELNET/SSHD/Console
HTTP/HTTPS/TELNET/SSHD/Console
Enable—allow manage Router by LAN(e.g.: HTTP)
Disable—forbid manage Router by LAN.
Remote Access Enable—allow to manage IR700 by WAN. (e.g.: HTTP)
Disable—forbid to manage IR700 by WAN. (e.g.: HTTP)
Allowed Access from WAN Set the range of allowed IP address for WAN
(Optional) (HTTP/HTTPS/TELNET/SSHD)
Description
Log Timeout
Describe the parameters of management (non-influence to IR700)
Other Parameters
Set the Log Timeout, configuration web will be disconnected after timeout
Default adm
123456
Enable
80/443/23/22/Blank
Enable
Enable
Control services server can be set at this time, for example 192.168.2.1/30 or 192.168.2.1-192.168.2.10
500 seconds
(5) System Log
Name
Log to Remote System
IP address/Port (UDP)
(6) Config Management
Description
Enable remote log server
Set the IP and Port of remote log server
Disable
Port: 514
Default
Name
Router Configuration
Restore default configuration
Network Provider (ISP)
(7) System Upgrade
Description
Import/Backup configuration file
Click to reset IR700 (to enable RESET, you need to reboot IR700)
Used to configure the APN, username, password and other parameters of major operators
To upgrade the system, click “System”=>”System upgrade” to enter upgrade page, then follow the steps below:
Click “Browse”, choose the upgrade file;
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Introduction to InRouter 700 Series
- 4 Overview
- 7 Package Checklist
- 8 Product Features
- 8 1.3.1 Interfaces
- 9 1.3.2 Functions
- 10 1.3.3 Environmental Limits
- 10 1.3.4 Power Requirements
- 10 1.3.5 Physical Characteristics
- 10 1.3.6 Advanced Industrial Features
- 11 1.3.7 Device Management Software
- 11 1.3.8 Warranty
- 12 Product Models
- 13 Quick Installation Guide
- 14 Typical Application
- 14 Panel Layout
- 16 Quick Connection to Internet
- 16 2.3.1 Insert SIM Card
- 16 2.3.2 Antenna Installation
- 16 2.3.3 Power Supply
- 16 2.3.4 Connect
- 17 2.3.5 Build Connection between InRouter and your PC
- 19 2.3.6 Start to configure your InRouter 700(Optional)
- 20 2.3.7 Connect InRouter with Internet
- 21 Quick IPSec VPN Configuration
- 23 Reset to Factory Defaults
- 23 Hardware Approach
- 24 2.5.2 Web Approach
- 25 Advanced Configuration
- 25 Configuration on Web
- 25 3.1.1 Preparation
- 27 3.1.2 System
- 31 3.1.3 Network
- 41 3.1.4 Service
- 45 3.1.5 Firewall
- 47 3.1.6 QoS
- 47 3.1.7 VPN(For IR79x only)
- 55 3.1.8 Tools
- 56 3.1.9 Status
- 59 CLI Configuration
- 59 4.1 CLI Operation
- 61 4.2 CLI command