Schneider Electric Quantum Ethernet Modules User Manual

Modicon Quantum with Unity
Ethernet Network Modules
User Manual
33002479 01
May 2004
2
Document Set
Document Set
Presentation
This package contains the following manuals:
z Quantum and Premium Communication Architecture Reference Manual
z Quantum TCPIP/IP Configuration User Manual
z Quantum Modbus Plus Network Modules
z Quantum Ethernet Network Modules User Manual
z 140 ESI 062 10 Quantum ASCII Interface Module User Manual
3
Document Set
4
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Part I Modicon Quantum with Unity Ethernet Products . . . . . 17
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 1
1.1
1.2
1.3
1.4
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Description 140 CPU 651 x0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
140 CPU 651 x0 Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Modicon Quantum Hot Standby with Unity 140 CPU 671 60
LCD Display Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Description 140 NOE 771 xx and 140 NWM 100 00 . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modicon Quantum Ethernet Modules Overview . . . . . . . . . . . . . . . . . . . . . . . . .
Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabling Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning Ethernet Address Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Establishing the FTP Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Establishing the HTTP Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using "BOOTP Lite" to Assign Address Parameters. . . . . . . . . . . . . . . . . . . . . .
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
20
20
21
22
25
27
29
38
38
39
43
45
46
46
47
49
51
52
53
54
57
61
64
65
65
5
Chapter 2
Provided Ethernet Services . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Modicon Quantum with Unity Ethernet Services . . . . . . . . . . . . . . . . . . . . . . . . . 68
Address Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
SNMP and Schneider Private MIB Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
MODBUS Messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
I/O Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Global Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Time Synchronization Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Electronic Mail Notification Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Bandwidth Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
FTP Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Embedded Web Pages — HTTP Server, Web Configuration and Diagnostics . . 81
Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Part II Modicon Quantum with Unity Ethernet Modules
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 3
3.1
3.2
3.3
3.4
6
Start Communication with Unity Pro . . . . . . . . . . . . . . . . . . . . 87
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
How to Configure the Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Add a New Network to the Communication Folder . . . . . . . . . . . . . . . . . . . . . . . 89
Configure Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Properties of a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Delete an Existing Network Folder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Unity Soft Communication Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Communication Configuration Principle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Link between Configuration and Communication . . . . . . . . . . . . . . . . . . . . . . . . 95
Link between Data and Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Selecting the Ethernet Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Selecting the Quantum NOE Ethernet Module . . . . . . . . . . . . . . . . . . . . . . . . . . 98
IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Quantum NOE Ethernet Messaging Configuration . . . . . . . . . . . . . . . . . . . . . . 101
Selecting the Ethernet Coprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Selecting the Modicon Quantum with Unity Ethernet Controller . . . . . . . . . . . . 103
Configuring the IP Address of the Ethernet Controller. . . . . . . . . . . . . . . . . . . . 105
Modicon Quantum with Unity Ethernet Controller Messaging Configuration . . . 106
Part III Using the Modicon Quantum with Unity Ethernet
Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Chapter 4
Transferring Data using Communication Blocks . . . . . . . . . 109
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CREAD_REG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CWRITE_REG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
READ_REG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WRITE_REG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCP_IP_ADDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MBP_MSTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MSTR Function Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read and Write MSTR Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read/Write MSTR Operation (FC 23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Get Local Statistics MSTR Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clear Local Statistics MSTR Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Get Remote Statistics MSTR Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clear Remote Statistics MSTR Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peer Cop Health MSTR Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Option Module MSTR Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read CTE (Config Extension Table) MSTR Operation . . . . . . . . . . . . . . . . . . .
Write CTE (Config Extension Table) MSTR Operation . . . . . . . . . . . . . . . . . . .
TCP/IP Ethernet Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5
Global Data (Publish / Subscribe) Utility . . . . . . . . . . . . . . . . 149
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Planning the Global Data (Publish / Subscribe) System . . . . . . . . . . . . . . . . . .
Multicast Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quantum NOE Global Data Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration of Global Data (Publish / Subscribe) by the Web for
NOE 771 x1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Global Data (Publish / Subscribe) Utility . . . . . . . . . . . . . . . . .
Chapter 6
109
111
114
117
120
123
125
129
133
134
135
136
137
138
139
141
142
144
146
149
150
154
155
157
161
I/O Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
I/O Scanner Concepts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Modicon Quantum with Unity I/O Scanner Configuration . . . . . . . . . . . . . . . . . 169
Chapter 7
Address Server Configuration /
Faulty Device Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address Server Configuration / Faulty Device Replacement . . . . . . . . . . . . . .
Understanding Faulty Device Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Faulty Device Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
171
172
175
178
7
Chapter 8
Network Management Service (SNMP) . . . . . . . . . . . . . . . . . 183
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
SNMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
ASN.1 Naming Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Configuring a NOE with SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Configuring a NOE with TFE Private MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Chapter 9
Time Synchronization Service . . . . . . . . . . . . . . . . . . . . . . . . 203
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Introducing the Time Synchronization Service. . . . . . . . . . . . . . . . . . . . . . . . . . 204
Using the Time Synchronization Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Using the R_NTPC Block for Time Synchronization . . . . . . . . . . . . . . . . . . . . . 208
Chapter 10
Electronic Mail Notification Service . . . . . . . . . . . . . . . . . . . . 209
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Introducing the Electronic Mail Notification Service . . . . . . . . . . . . . . . . . . . . . . 210
Using the Mail Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Using the MSTR Block for Mail Service Communication . . . . . . . . . . . . . . . . . . 212
Mail Service Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Chapter 11
Embedded Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Accessing the Web Utility Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Quantum Welcome Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Configured Local Rack Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
CPU Configuration Screen Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Ethernet Module Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Remote I/O Communication Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Quantum PLC Data Monitor Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Configure NOE Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Configure SNMP Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Configuring the Global Data (Publish / Subscribe) Utility. . . . . . . . . . . . . . . . . . 236
Configure Address Server Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Configuring the Time Synchronization Service . . . . . . . . . . . . . . . . . . . . . . . . . 244
Configuring the Electronic Mail Notification Service . . . . . . . . . . . . . . . . . . . . . 249
Extended Web Diagnostics Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
NTP Diagnostics Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Email Diagnostics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
NOE Properties Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Crash Log Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Contacting Schneider Electric Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Chapter 12
Hot Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Overview of Modicon Quantum Hot Standby with Unity Solution for NOEs . . . 266
Hot Standby Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8
NOE Configuration and Hot Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Address Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOE Operating Modes and Modicon Quantum Hot Standby with Unity . . . . . .
Address Swap Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Effects of Modicon Quantum Hot Standby with Unity Solution . . . . . .
Appendices
269
270
272
275
276
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Appendix A
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Responding to Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading and Clearing the Crash Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading a New NOE Exec. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading a New NOE Exec via FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading a New NOE Kernel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B
281
282
287
288
289
291
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Appendix C
Quantum Ethernet TCP/IP Modbus Application Protocol . . . 297
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modbus Application Protocol PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modbus Application Protocol Service Classes . . . . . . . . . . . . . . . . . . . . . . . . .
Modbus Application Protocol PDU Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCP/IP Specific Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
297
298
299
301
302
304
305
Glossary
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
9
10
Safety Information
§
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
The addition of this symbol to a Danger or Warning safety label indicates
that an electrical hazard exists, which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation, which, if not avoided, will
result in death, serious injury, or equipment damage.
WARNING
WARNING indicates a potentially hazardous situation, which, if not avoided, can result
in death, serious injury, or equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation, which, if not avoided, can result
in injury or equipment damage.
identifier not found
11
Safety Information
PLEASE NOTE
12
Electrical equipment should be serviced only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use
of this material. This document is not intended as an instruction manual for untrained
persons.
© 2004 Schneider Electric. All Rights Reserved.
About the Book
At a Glance
Document Scope
This documentation describes the functionality of the Modicon Quantum Ethernet
modules, the NOE 771 xx and 140 NWM 100 00 and the Ethernet port of the
140 CPU 651 x0 modules.
Model Numbers
140 NOE 771 00
140 NOE 771 01
140 NOE 771 10
140 NOE 771 11
140 NWM 100 00
140 CPU 651 50
140 CPU 651 60
This documentation should provide you with the knowledge to begin using a
Modicon Quantum Ethernet module and Ethernet equipped controller to
communicate with devices over an Ethernet network. This documentation includes
information about:
z Hardware architecture of a Modicon Quantum Ethernet TCP/IP module designed
to fit into a single slot on the standard Modicon Quantum backplane
z Capabilities of the NOE 771 xx and NWM 100 00 modules
z Capabilities of the Ethernet port of the 140 CPU 651 x0 CPU modules
z Installation of the NOE 771 xx and NWM 100 00 modules onto a Modicon
Quantum backplane
identifier not found
13
About the Book
This documentation describes the procedures for:
z Setting up the modules to transfer data using one of two methods:
z Global Data (Publish / Subscribe) Utility
The Global Data modules (NOE 771 01 and NOE 771 11)
z I/O Scanner
The I/O scanner modules
|(NOE 771 -00, -01, -11 only and 140 CPU 651 -50, -60)
z Using an embedded Web server to access diagnostics and online configurations
for the module and its associated controller
z Using the FatoryCast Web server to customize your configuration via embedded
Web pages (140 NOE 771 -10, -11 and 140 NWM 100 00)
z Using the NOE in a Hot Standby solution that provides fault tolerance for the
remote I/O and communications
Nomenclature
The following table describes the naming scheme for
140 NOE 771
Model Numbers
xx
refers to
-00, -01, -10, -11
x0
refers to
-00, -10
x1
refers to
-01, -11
0x
refers to
-00, -01
1x
refers to
-10, -11
The following table describes the naming scheme for
140 CPU 651
xx
Model Numbers
refers to
-50 and -60
Note: Who Should Use This Documentation?
This documentation is intended to support anyone using a Quantum PLC that
needs to communicate with devices over an Ethernet network. You are expected
to have some knowledge about the use of PLC systems and possess of a working
knowledge of either the Modsoft, Concept, ProWORX, or Unity Pro programming
tools. You also need to understand the use of an Ethernet network and TCP/IP.
Note: Adding Ethernet Nodes
Before adding a node to an existing corporate network, consult with your
information technology (IT) department about any possible consequences.
This documentation is valid for Unity Pro version 2.0 and higher.
14
About the Book
Validity Note
Related
Documents
The data and illustrations found in this documentation are not binding. We reserve
the right to modify our products in line with our policy of continuous product
development. The information in this document is subject to change without notice
and should not be construed as a commitment by Schneider Electric.
Title of Documentation
Reference Number
Quantum Hardware Reference Manual
UNYUSE10010V20E
Quantum Discrete and Analog I/O Reference Manual
UNYUSE10010V20E
Quantum Experts and Communication Reference Manual
UNYUSE10010V20E
Grounding and Electromagnetic Compatibility of PLC Systems User
Manual
UNYUSE10010V20E
Quantum and Premium Communication Architecture Reference
Manual
Part of this package
Schneider Automation BooTP Lite Ethernet IP Address Download
31002087
Utility for Schneider Automation Ethernet Products Instruction Sheet
FactoryCast for Quantum, Premium and Micro User Guide
31001229
Modicon Quantum Hot Standby with Unity User Manual
UNYUSE10710V20E
MODBUS Protocol Reference Guide
PI-MBUS-300
Open MODBUS Specification
http://
www.modbus.org/
Factory Cast HMI 140 NWM 100 00 User Guide
890USE15200
Note: Some of the preceding documents are available only in online form at this
time.
15
About the Book
Product Related
Warnings
Schneider Electric assumes no responsibility for any errors that may appear in this
document. If you have any suggestions for improvements or amendments or have
found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic
or mechanical, including photocopying, without express written permission of
Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to ensure compliance
with documented system data, only the manufacturer should perform repairs to
components.
When controllers are used for applications with technical safety requirements,
please follow the relevant instructions.
Failure to use Schneider Electric software or approved software with our hardware
products may result in injury, harm, or improper operating results.
Failure to observe this product related warning can result in injury or equipment
damage.
User Comments
We welcome your comments about this document. You can reach us by e-mail at
[email protected]
16
Modicon Quantum with
Unity Ethernet Products
I
At a Glance
Purpose
This part introduces the Modicon Quantum with Unity products used for Ethernet
communication.
What's in this
Part?
This part contains the following chapters:
Chapter
Chapter Name
Page
1
Product Description
19
2
Provided Ethernet Services
67
17
Ethernet Products
18
Product Description
1
At a Glance
Introduction
This chapter provides product overviews of the Quantum modules for Ethernet
communication. It covers the 140 NOE 771 xx modules, the 140 NWM 100 00
module, and the built-in Ethernet port of the 140 CPU 651 x0 modules.
What's in this
Chapter?
This chapter contains the following sections:
Section
Topic
Page
1.1
Module Description 140 CPU 651 x0
20
1.2
Module Description 140 NOE 771 xx and 140 NWM 100 00
38
1.3
Installing the Module
46
1.4
Customer Support
65
19
Product Description
1.1
Module Description 140 CPU 651 x0
Introduction
Overview
This section contains the module descriptions for the 140 CPU 651 x0.
What's in this
Section?
This section contains the following topics:
20
Topic
Page
140 CPU 651 x0 Product Overview
21
Presentation
22
Keypad Operation
25
Indicators
27
Using the Modicon Quantum Hot Standby with Unity 140 CPU 671 60 LCD
Display Screens
29
Product Description
140 CPU 651 x0 Product Overview
Overview
The following information is an overview about the Quantum Processor Modules 140
CPU 651 x0.
General
Description
The Quantum-140 CPU 651 x0 module shown below, is one of the newest models
in a series of Quantum processor modules. It unites the standard functions of the
PLC and the diagnostic possibilities of a Web server. The 140 CPU 651 x0
communicates using an RJ-45 connection.
The 140 CPU 651 x0 module is in a double-width standard Quantum housing, which
requires 2 sequential slots in a Quantum rack.
The Modicon Quantum processor 140 CPU 651 x0 Web server functions are
diagnostic only. Therefore, use the software to configure services.
The 140 NOE 771 xx modules offer embedded Web pages that enable you to both
configure and diagnose services.
The table shows the diagnosis possibilities implemented:
Service
140 CPU 651 x0
HTTP Server
x
FTP Server
x
Flash File System
x
BOOTP Client
x
Address Server
x
SNMP V2 Agent (Network Management Service)
x
Modbus Messaging
x
I/O Scanner
x
Hot Standby
Global Data - Publish / Subscribe
x
Bandwidth Monitoring
x
Faulty Device Replacement (Server)
x
Enhanced Web Diagnosis
x
Schneider Private MIB
x
FactoryCast Application
User-programmed Web pages
RJ-45 Connection
x
Fiber Optic Connection
Time Synchronization Service
X
Electronic Mail Notification Service
21
Product Description
Presentation
Illustration
The following figure shows the High End CPU Module and its components.
1
140
CPU 651 60
PENTIUM CONTROLLER
2
3
RESTART
13
4
MOD
ENTER
5
MODBUS
ESC
6
USB
12
7
8
9
COM
STS
10
11
Mac Address
00:00:##:##:##:##
1
2
3
4
5
6
7
8
9
10
11
12
13
22
Model Number, Module Description, Color Code
Lens Cover (open)
LCD Display (here covered by the Lens Cover)
Key Switch
Keypad
Modbus port
USB port
Modbus Plus port
PCMCIA Slots (Type II, Type III)
Indicators for Ethernet communication
Ethernet port
Battery
Reset Button
Product Description
Lens Cover
The Lens Cover serves as a protection, which can be opened by sliding upwards.
With the Lens Cover open you have access to the following items:
z Key Switch
z Battery
z Reset Button
LCD Display
The Modicon Quantum High End CPU with Unity has a standard 2 line by 16
character LCD display with changeable backlight state and contrast. The backlight
handling is entirely automated to save the life of the LEDs in the LCD.
The backlight turns on when the keypad driver detects a key press, the key switch
state is changed, or when an error message is displayed on the LCD. The backlight
automatically turns off after 5 minutes if there has been no key switch or keypad
activity during that time period. The backlight will stay on for error messages as long
as the error message is displayed on the LCD screen.
2 Line by 16 character LCD
Keypad
The Modicon Quantum High End with Unity keypad consists of five keys that are
mapped to a hardware address. On each of the two arrow keys there is an LED.
5 key keypad with 2 LEDs
1
2
1
5 keys
2
2 LEDs
23
Product Description
Key Switch
The key switch is used as an authorization level security feature and Memory
Protection switch. The key switch has two positions: Locked and Unlocked. The key
switch will only be read and deciphered by the PLC OS (Executive) portion of the
firmware and not by the OS Loader portion.
The Modicon Quantum High End CPU has a set of system menus, which enable the
operator to perform PLC operations (i.e. Start PLC, Stop PLC) and display module
parameters (i.e. Communications parameters).
PLC operations depending on the key position
Key position
PLC operation
unlocked
z
z
locked
z
z
all system menu operations are able to be invoked and all changeable
module parameters are able to be modified by the operator via the LCD
and keypad.
memory protection is off
no system menu operations are able to be invoked and all module
parameters are read only.
memory protection is ON
Switching the key switch position from locked to unlocked or vice versa will turn on the LCD's
backlight.
Reset Button
24
When pressed, this button forces a cold start of the PLC.
Product Description
Keypad Operation
Function
Table of function
Key
ESC
ENTER
MOD
Function
To cancel an entry, or suspend or stop an action in progress
To display the preceding screens successively (step up the menu tree)
To confirm a selection or an entry
To set a field on the display into modify mode
LED: on
key active
z To scroll through menu options
z To scroll through modify mode field options
LED: flashing
key active
z Field in modify mode has options to scroll through
LED: off
key inactive
z No menu options, no field options
LED on
key active
z To move around in a screen, field to field
z To go to the sub-menu
LED flashing
key active
z To move around in a field that is in modify mode,
digit to digit
LED off
key inactive
z No sub-menu for menu option
z No moving around in a screen
z No moving around in a field
25
Product Description
Contrast
Adjustment
The contrast is adjustable from the keypad when the Default screen is displayed as
follows:
Step
1
Action
Press the MOD key:
MOD
2
To adjust the contrast darker press:
3
To adjust the contrast lighter press:
4
To confirm the setting press:
ENTER
Backlight
26
Pressing a key will turn on the LCD backlight (if it was off). When there is no activity
from the keypad for 30 minutes the Default Screen will return to the display. When
the user presses the < ESC > key and the LCD backlight was off, the LCD
backlight will turn on and the Default Screen will stay as the displayed screen.
If at any time the executive detects an error in the CPU it will display an error
message to the LCD and the LCD's backlight will turn on until the error condition
disappears
Product Description
Indicators
The High End CPU uses two types of indicators:
1. LCD Display, p. 23:
The Understanding the Default Screen, p. 31 serves as a Controller status screen
2. LED Indicators:
For the function refer to LED Description, p. 28
The following figure shows the two types of indicators.
140
CPU 651 60
1
MOD
ENTER
MODBUS
ESC
USB
Overview
2
2
COM
COM
STS
STS
Mac Address
00:00:##:##:##:#
1
LCD Display (lens cover closed)
2
LED Indicators
27
Product Description
LED Description
The following table shows the description for the LED indicators of the different High
End CPU modules.
LEDs
Color
Indication
CPU 651 50 and CPU 651 60
COM
Green
Controlled by the Coprocessor hardware
z Indicates Ethernet activity
STS
Red
Controlled by the Coprocessor software
ON
all is OK
OFF
abnormal end of copro boot; possible hardware problem
Flashing:
28
1 Flash
Configuration in progress
Temporary situation
2 Flashes
Invalid MAC address
3 Flashes
Link not connected
4 Flashes
Duplicate IP Address
5 Flashes
Waiting for a served IP Address
7 Flashes
Firmware incompatibility exists between PLC OS and
Copro firmware
Product Description
Using the Modicon Quantum Hot Standby with Unity 140 CPU 671 60 LCD
Display Screens
Overview
The controller’s LCD displays messages. These messages indicate the controller’s
status. There ae four levels of menus and submenus. All menus are accessed using
the keypad on the front of the controller.
For detailed information about the menus and submenus see:
z Using the PLC Operations Menus and Submenus, p. 32
z Using the Communications Menus and Submenus, p. 33
z Using the System Info Menus and Submenus, p. 36
z Using the LCD Settings Menus and Submenus, p. 37
Structure: LCD display menus and submenus
Mode
1
2
State
Bat L
port
Quantum
PLC Operations =>
Quantum
Communications =>
Quantum
System Info =>
Quantum
LCD Settings =>
3
4
1
Default Screen
2
System Menus
3
Sub Menus
4
Sub Screens
29
Product Description
Accessing the
Screens
Use the keys on the keypad to access the system menus and submenus.
Step
Action
1
To access the screens, ensure that the key switch is in the unlocked position .
2
To step down to a lower menu, operate one of the following keys:
ENTER
3
To return to the previous menu, press:
ESC
30
Product Description
Understanding
the Default
Screen
Default screen displays the following information
Mode
State
port
Bat L
PCM
The default screen is read only.
Default
Screen
Displays
Fields
Available
Options Description
Available
Default
State
RUN
Application program is running
RUN Primary
RUN Standby
RUN Offline
STOP
Application program is NOT running
No Conf
CPU has no application program
STOP Offline
BatL
Port
Indicates health of battery
Steady = Battery is low
No message = Battery is OK
z
z
USB
Indicates that port has activity
Modbus
Plus
MB+
mb+
No activity
Modbus
232
Serial port activity for RS-232
485
Serial port activity for RS-485
1
Indicates the card in slot 1 is being accessed
The status displayed indicates the health of the
battery
z Steady = Battery is OK
z No message = Batery is low
2
Blinks, when the card in slot 2 is being accessed
The status displayed indicates the health of the
battery
z Steady = Battery is OK
z No message = Batery is low
PCM
Indicates Modbus Plus activity
31
Product Description
Using the PLC
Operations
Menus and
Submenus
Structure: PLC Operations menu and submenus
Quantum
PLC Operations =>
PLC Operations
Start PLC
=>
Press <ENTER> to
confirm Start
=>
PLC Operations
Stop PLC
=>
Press <ENTER> to
confirm Stop
=>
PLC Operations
Init PLC
=>
Press <ENTER> to
confirm Init
=>
Submenu: PLC Operations: Start, Stop, Init
32
Start, Stop, Init
Fields Available
Screens Display
Description
Start PLC
Press <ENTER> to confirm Start
Pressing <ENTER> starts the
controller
Stop PLC
Press <ENTER> to confirm Stop
Pressing <ENTER> stops the
controller
Init PLC
Press <ENTER> to confirm Init
Pressing <ENTER> initializes the
controller
Product Description
Using the
Communications
Menus and
Submenus
Structure: Communications menu and submenus structure
Quantum
PLC Communications =>
Communications
TCP/IP Ethernet =>
TCP/IP Ethernet
IP Address
=>
IP Address:
###.###.###.###
TCP/IP Ethernet
Subnet Mask
=>
Subnet Mask:
###.###.###.###
TCP/IP Ethernet
IP Gateway
=>
IP Gateway:
###.###.###.###
TCP/IP Ethernet
MAC Address =>
MAC Address:
Communications
Modbus Plus
=>
MB+ Address:
Communications
Serial Port
=>
Mode Protocol: Adr
##.##.##.##.##.##
##
Modbus Plus State
Rate,Par,DB,SB
=>
Serial Port
RS-Mode: RS-232
Serial Port
Protocol: Modbus
Serial Port
Unit Address:
1
Serial Port
Baudrate:
9600
Serial Port
Parity:
Even
Serial Port
Databits:
RTU - 8
Serial Port
RS-Mode: RS-232
Serial Port
Stopbits:
1
33
Product Description
Submenu: PLC Communications: TCP/IP Ethernet
TCP/IP Ethernet
Screen Displays
Fields Available
Options Available
Description
TCP/IP Ethernet
###.###.###.###
(not modifiable)
decimal numbers
displays IP address
###.###.###.###
(not modifiable)
decimal numbers
displays Subnet
Mask address
decimal numbers
IP Gateway
###.###.###.###
(not modifiable)
displays Ethernet IP
Gateway address
TCP/IP Ethernet
MAC Address
##.##.##.##.##.##
(read only)
hexadecimal numbers
displays MAC
(Medium Access
Control) address
IP Address1,2
TCP/IP Ethernet
Subnet Mask
1
TCP/IP Ethernet
1
Submenu: PLC Communications: Modbus Plus
Modbus Plus
Screen Displays
Fields Available
Options
Available
Description
Modbus Plus
Address
##
(modifiable only if the key
switch is in the unlocked
position)
1-64
to enter a valid
Modbus Plus address
Modbus Plus State
Monitor Link
Modbus Plus State
Normal Link
Sole Station
Duplicate address
No Token
34
Product Description
Submenu: PLC Communications: Serial Port
Seriial Port
Screen Displays
Fields
Available*
Options Available
Description
Serial Port
Mode
232
RS mode
485
Protocol
ASCII
Protocols available
RTU
Adr
1 - 247
Unit address
for Modbus switchover
Primary 1-119
Standby 129 - 247
Rate
50, 75, 110, 134.5, 150, 300, 600, Baud rate
1200, 1800, 2400, 3600. 4800,
7200, 9600, 19200 bits/s
Par
NONE
Parity
ODD
EVEN
DB
SB
*
7,8
Databits:
if Protocol is Modbus
then RTU-8 or ASCII-7
1,2
Stopbits
If the key switch is in the unlocked position, all fields are modifiable.
35
Product Description
Using the
System Info
Menus and
Submenus
Structure: System Info menus and submenus
Quantum
System Info
=>
System Info
Stop Code
=>
Stop Code: ####
Description
System Info
Firmware Info
=>
OS Ldr Rev: ##.##
Exec Rev: ##.##
System Info
Hardware Info
=>
HW Rev:
Rev
SN:
########
Submenu: PLC Communications: System Info
System Info
Fields
Screen Displays Available*
Stop Code
Firmware Info
Hardware Info
Description
####
shows the machine stop code
Description
shows the description to the machine stop code
##.##
shows the number of OS Loader Revision
##.##
shows the number of Exec Revision
Rev
shows the number of Hardware Revision
########
shows the serial number of Hardware
*
36
Option
Available
All fields are read only.
Product Description
Using the LCD
Settings Menus
and Submenus
Structure: LCD Settings menus and submenus
Quantum
LCD Settings
=>
LCD Settings
LCD Contrast: ###
0% is black
100% is green
LCD Settings
LCD Light:
time
On
Off
1 Min
5 Min
10 Min
15 Min
Submenu: LCD Settings: LCD Contrast
LCD Screen Contrast
Screen Displays
Fields
Description
Available
LCD Contrast:
####
A lower percent is darker. A higher percent is brighter.
Use the arrow keys to adjust the setting.
z Up arrow increases percent
z Down arrow decreases percent
Submenu: LCD Settings: LCD Light
Screen Displays
Fields Available
Description
LCD Light:
On
LCD light remains on permanently or until changed
Off
LCD light remains off permanently or until changed
1 Min
LCD light remains on for one minute
5 Min
LCD light remains on for five minutes
10 Min
LCD light remains on for ten minutes
15 Min
LCD light remains on for fifteen minutes
37
Product Description
1.2
Module Description 140 NOE 771 xx and
140 NWM 100 00
Introduction
Overview
This section contains the module descriptions for 140 NOE 771 xx and
140 NWM 100 00.
What's in this
Section?
This section contains the following topics:
38
Topic
Page
Modicon Quantum Ethernet Modules Overview
39
Indicators
43
Connectors and Cabling
45
Product Description
Modicon Quantum Ethernet Modules Overview
Overview
The following information provides overviews of all Modicon Quantum Ethernet
modules.
General
Description
The Modicon Quantum Ethernet module, shown below, is one of the latest models
in a line of Modicon Quantum Ethernet TCP/IP modules designed to make it
possible for a Modicon Quantum Programmable Logic Controller (PLC) to
communicate with devices over an Ethernet network. The electronics for the
Ethernet modules are contained in a standard Modicon Quantum single width case
that takes up one slot in a Modicon Quantum backplane. The module, which is
capable of being hot swapped, can be plugged into any available slot in the
backplane.
The NOE 771 00 provides real-time peer-to-peer communications as well as I/O
scanning and a MODBUS/TCP server. The included HTTP services provide
maintenance and configuration utilities to the module.
NOEs in a Rack
The following table summarizes the total number of NOE modules per CPU.
Modicon Quantum CPU Type
Supports NOEs
140 CPU 311 10
2
140 CPU 434 12A
6
140 CPU 534 14A
6
140 CPU 651 50
6
140 CPU 651 60
6
140 CPU 671 60
6
39
Product Description
Key Features
The following table shows the different feature of the 140 NOE 771 xx and 140 NWM
100 00 Ethernet modules.
The key features of the 140 NOE 771 (-00, -01, -10, -11) and 140 NWM 100 00
models are listed below:
Service
-00
-01
-10
-11
NWM
HTTP Server
X
X
X
X
X
FTP Server
X
X
X
X
X
Flash File System
X
X
X
X
X
BOOTP Client
X
X
X
X
X
Address Server
X
X
X
X
SNMP V2 Agent
(Network Management Service)
X
X
X
X
X
MODBUS Messaging
X
X
X
X
X
I/O Scanner
X
X
X
Hot Standby
X
X
Global Data - Publish / Subscribe
X
X
Bandwidth Monitoring
X
X
Faulty Device Replacement (Server)
X
X
Enhanced Web Diagnostics
X
X
X
Schneider Private MIB
X
X
X
FactoryCast Application
X
X
X
User-programmed Web pages
X
X
X
X
JAVA Virtual Machine
X
Fiber optic connection
X
X
X
RJ-45 connection
X
X
X
Time Synchronization Service
Electronic Mail Notification Service
X
X
X
X
Note: In the detailed description of the key features, only the modules of the NOE
family are named. The features are also available for the 140 NWM 100 00 module.
This applies depending on the listed properties in the table shown above.
40
Product Description
Front Panel
Components
The front panel of the Ethernet modules contain identification markings, color codes,
and LED displays. A writable area for an IP address, a global address label, and two
Ethernet cable connectors is located behind the removable front panel door.
The following table provides a description of the front panel components which are
shown in front view figure.
Component
Description
LED indicator Panel
Indicates the operating status of the module, and the fiber optic or
Ethernet communications network it is connected to. (See LED
Indicators in this chapter.)
IP Address Area
Provides a writable area to record the module’s assigned IP
address.
Global Address Label
Indicates the module’s global Ethernet MAC address assigned at
the factory.
100 BASE-FX
Connector
Provides an MT-RJ socket for connection to a 100 megabit fiber
optic Ethernet cable.
10/100BASE-T
Connector
Provides an RJ-45 socket for connection to a shielded, twisted pair
Ethernet cable.
41
Product Description
Front View
The following figure shows the front of the NOE 771 00 Ethernet module as an
example for all Ethernet modules.
WRITE ASSIGNED IP ADDRESS ABOVE
Do Not Duplicate Address
Use Permanent Felt-tip Pen
140
NOE 771 00
1
Ethernet 10/100
Active
Ready Fault
Run
Coll
Link
Tx Act
Rx Act
10MB
100MB Fduplex
Kernel Appl
2
3
WRITE ASSIGNED IP ADDRESS ABOVE
Do Not Duplicate Address
Use Permanent Felt-tip Pen
4
5
6
1
2
3
4
5
6
7
42
Base
Fx
00
-T
Model number, module description, color code
LED display
IP Address writable area
Global address label
100 Base Fx MT-RJ cable connector
10/100 Base-T RJ-45 cable connector
Removable door
7
Product Description
Indicators
Illustration
The following figure shows the NOE 771 00 LED indicators as a place holder for all
other Ethernet modules.
Active
Ready
Fault
Run
Link
Coll
Tx Act
RxÅ Act
10MB
Description
100MB
Fduplex
Kernel
Appl
The following table shows the LED descriptions.
LED
Color
Description
Active
Green
Indicates the backplane is configured.
Ready
Green
Indicates module is healthy.
Fault
Red
Flashes when the NOE is in crash state.
Run
Green
Flashes to indicate diagnostic code, as described in "Run LED Status"
(below).
Coll.
Red
Flashes when Ethernet collisions occur.
Link
Green
On when Ethernet link is active.
Tx Act
Green
Flashes to indicate Ethernet transmission.
Rx Act
Green
Flashes to indicate Ethernet reception.
10MB
Green
On when the module is connected to a 10 Megabit network.
100MB
Green
Fduplex
On when the module is connected to a 100 Megabit network.
On when Ethernet is operating in the full duplex mode.
Kernel
Amber
On when in Kernel Mode.
Flashing while in download mode.
Appl
Green
On when crash log entry exists.
43
Product Description
Run LED Status
The following table lists each available state of the Run LED indicator, and it
provides diagnostic information for that state
Indicator State
Status
On (steady)
Normal operation: The NOE module is ready for network
communication.
Number of flashes in sequence
one
Not used
two
Not used
three
No Link: the network cable is not connected or is defective
four
Duplicate IP address: The module will stay off-line.
five
No IP address: The module is attempting to obtain an IP address
from a BOOTP server.
six
Using default IP address
seven
No valid executive NOE present
eight
Invalid IP configuration (Likely cause: Default gateway is not on the
(140 NWM 100 00 only) same subnet mask.)
nine
Flash file system inoperative.
(140 NWM 100 00 only)
44
Product Description
Connectors and Cabling
Overview
The following information describes the 10/100 BASE-T and 100 BASE-FX
connectors.
10/100 BASE-T
Twisted Pair
Connector
The NOE 771 xx, NWM 100 00, and CPU 651 x0 modules’ 10/100 BASE-T
connector (shown below) is a standard RJ-45 twisted pair socket.
The following figure shows the 10/100 BASE-T connector.
Pins
8
1
Schneider Electric recommends that you use Category 5 STP cabling, which is rated
to 100 Mbps, with an RJ-45 connector.
The eight pins are arranged vertically and numbered in order from the bottom to the
top. The RJ-45 pinout used by this module is:
z Receive Data (+)3
z Receive Data (-)6
z Transmit Data (+)1
z Transmit Data (-)2
100 BASE-FX
The NOE 771 xx, NWM 100 00, and CPU 651 60 modules’ 100 BASE-FX connector
is a MT-RJ socket or a mating fiber optic cable connector. (See the figure in the block
Front View, p. 42).
For the NOE 771 xx and NWM 100 00, you may need an MT-RJ to SC (Duplex)
multimode fiber optic cable assembly 62.5/125mm. Schneider Electric recommends
cable number 490NOC00005 to connect to fiber hubs/switches.
Note: The NOE 771 xx and NWM 100 00 is an one channel device. It is capable
of communicating over either a 10/100BASE-T or a 100BASE-FX Ethernet network
at any given time, but not over both at the same time.
45
Product Description
1.3
Installing the Module
Overview
Introduction
This section contains installation and configuration information for the Ethernet
modules.
What's in this
Section?
This section contains the following topics:
Topic
Before You Begin
46
Page
47
Cabling Schemes
49
Security
51
Installing the Module
52
Connecting the Cable
53
Assigning Ethernet Address Parameters
54
Establishing the FTP Password
57
Establishing the HTTP Password
61
Using "BOOTP Lite" to Assign Address Parameters
64
Product Description
Before You Begin
Overview
The following information describes how to install the NOE 771 xx module.
Initial Checks
Before you install your module, you need to complete the following checks.
z Determine how the NOE 771 xx module will be assigned its Ethernet address
parameters (the default method is BOOTP)
z Verify that your Ethernet network is properly constructed
CAUTION
UNINTENTIONAL OPERATION
If you do not enter the correct address pairs into the BOOTP server, you
could communicate to the wrong device.
z Ensure the MAC address matches the intended IP address in your
BOOTP server.
Having two or more devices with the same IP address can cause
unpredictable operation of your network.
z Ensure that your Ethernet module receives a unique IP address.
Failure to follow this precaution can result in injury or equipment
damage.
Determining the
Appropriate
Ethernet
Address
Parameters
Consult your system administrator to determine if you must configure a new IP
address and appropriate gateway and subnet mask addresses, or whether the
module will obtain its Ethernet address parameters from a BOOTP server. If the
administrator assigns new address parameters, you will need to configure the
module from your programming panel. Follow the directions in the Configuring the
Module with Concept chapter.
47
Product Description
Verifying the
Network
Topology
You should not use a standard cable to connect an Ethernet Web embedded server
module directly to another device, you have to use a cross link cable. For the
network to operate properly, you must route the cable for each device through an
Ethernet hub/swit
The following figure shows two incorrect network topologies.
NOE
NOE
NOE
The following figure shows a correct network topology.
NOE
NOE
Hub/Switch
48
Product Description
Cabling Schemes
Overview
The following information describes how to connect devices in a standard Ethernet
cabling.
Introduction
In a standard Ethernet cabling scheme, each device connects via a cable to a port
on a central Ethernet hub/switch.
Twisted Pair
Length
The purpose of the following table is to show that the maximum length of cable
between devices depends on the type of device.
Type of
Device
Max. Cable from
Device to Hub
Max. Hubs Between
Any Two Nodes
Max. Cable Between Most
Distant Nodes on Network
Hub
100 m
4
500 m
Switch
100 m
Unlimited
Unlimited
For Fast Ethernet (100 Base-T) specifications, please refer to the IEEE 802.3u
Standard available from the IEEE (www.IEEE.org).
Cabling with
Conventional
Hubs
The figures and tables that follow show the maximum number of hubs and the
maximum cable length between devices allowed if using hubs.
10 BASE-T Cable
Distances
The following figure is for 10 BASE-T cable
500 m (1625 ft) maximum cable length between devices on the network
Hub
Hub
Hub
Hub
Backplane
Backplane
Backplane
Backplane
Backplane
49
Product Description
100 BASE-T
Cable Distances
100 BASE-FX
Cable Distances
The 100 BASE-T cabling allows for two hubs with a link maximum distance of 100
m (325 ft), and a total network diameter of 205 m (665 ft).
The following table provides information about the maximum distance parameters
with 100 BASE-T.
Model
Length max. in Twisted pair TX-T2-T4
DTE-DTE (no repeater)
100 m (325 ft)
One Class I repeater
200 m (650 ft)
One Class II repeater
200 m (650 ft)
Two Class II repeaters
205 m (665 ft)
The 100 BASE-FX cabling allows for two hubs with a link maximum distance of 412
m (1339 ft), and a total network diameter of 205 m (665 ft).
The following table provides information about the maximum distance parameters
with 100 BASE-FX and 100 BASE-TX-FX.
Model
Length max. Twisted pair
TX and Fiber FX
Length max. Fiber FX
DTE-DTE (no repeater)
n.a.
412 m (1339 ft)
One Class I repeater
260.8 m (1)
272 m (884 ft)
One Class II repeater
308.8 m (1)
320 m (1040 ft)
Two Class II repeaters
216.2 m (2)
228 m (741 ft)
(1) Mixed twisted pairs and fiber assumes a 100 m (325 ft) twisted pair links
(2) Mixed twisted pairs and fiber assumes a 105 m (340 ft) twisted pair links
Fiber Length
50
The maximum length for 850 nm/Multimode cable is 2 KM.
Product Description
Security
Overview
The following information describes firewalls. A firewall is a gateway that controls
access to your network. To restrict access to your Ethernet controller and I/O
network, you may want to consider a firewall.
Types of
Firewalls
There are two types of firewalls.
z Network-level firewalls
z Application-level firewalls
Network-Level
Firewalls
Network-level firewalls are frequently installed between the Internet and a single
point of entry to an internal, protected network.
ApplicationLevel Firewalls
An application-level firewall acts on behalf of an application. It intercepts all traffic
destined for that application and decides whether to forward that traffic to the
application. Application-level firewalls reside on individual host computers
Port Numbers
Used by NOE
The following table contains the port numbers used by NOE
Protocol
Port Number
Modbus/TCP
TCP 502
HTTP
TCP 80
SNMP
UDP 61
FTP
TCP 21
You may need to provide the information in this table to your system administrator
so that the firewall configuration will allow access to your PLC from outside of your
facility.
51
Product Description
Installing the Module
Overview
The following information describes how to install the NOE 771 xx module.
Before You
Begin
Locate the backplane in which you will mount the NOE 771 xx module. Ensure that
an open slot is available in which to mount the module.
Note: The NOE 771 xx module can be installed only in a local backplane.
Note: Power requirements
z Ensure when installing the NOE that it does not exceed the Quantum backplane
requirements.
Backplane Slot
Placement
The modules may be placed in any slot on the backplane. They do not have to be
placed next to each other.
Tools Required
You will need one medium-size, Phillips-head screw driver.
Mounting the
Module in the
Backplane
Perform the following steps to mount the NOE 771 xx module on to a Quantum
backplane.
Step
Action
1 Holding the module at an angle, mount it on the two hooks located near the top of the
backplane.
The following figure shows the correct way to hold the module.
Hook
Backplane
Connector
Module
Backplane
2 Swing the module down so its connector engages the backplane connector.
3 Using a Phillips-head screw driver, tighten the screw at the bottom of the module between
2 and 4 in-lbs or between .22 and .45 Newton meters of torque.
52
Product Description
Connecting the Cable
Overview
The following information pertains to cabling.
Note: The 140 NOE 771 xx is capable of communicating over either a 10/100BASE-T or a
100BASE-FX Ethernet network at any given time, but not both at the same time.
Accessories
The following are switches that are sold by Schneider Electric.
Hub or Switch
Description
499NEH10410
Hub with 4 ports 10BASE-T
499NOH10510
Hub with 3 ports 10BASE-T and 2 ports 10BASE-FL
499NTR10010
Transceiver 10BASE-T / 10BASE-FL
499NEH14100
Hub with 4 ports 100BASE-TX
499NTR10100
Transceiver 100BASE-TX
499NES18100
Switch with 8 ports 10/100BASE-TX
499NES17100
Managed Switch with 7 ports 10/100BASE-TX
499NOS17100
Managed Switch with 5 ports 10/100BASE-TX and 2 ports 100BASE-FX
The following are Schneider Electric cables that support Multicast Filtering
Cable
Fiber Optic
Description
490NTW000 02/05/12/40/80 U
StraightThru cable
490NTC000 05/15/40/80 U
Crossover cable
Remove the protective cap from the module’s MT-RJ connector port and the
protective cap from the tip of the black connector on the MT-RJ fiber optic cable (as
shown in the following figure). Note the plug only fits to the socket in one way. It
should snap into place.
The following figure shows MT-RJ fiber optic cable.
53
Product Description
Assigning Ethernet Address Parameters
Overview
The following information describes how to assign IP address parameters.
As shipped from the factory, the NOE 771 xx module does not contain an IP
address. If you have not programmed the unit with an Ethernet configuration
extension, the module does not contain an IP address. When the module starts up
without an IP address, the module will attempt to obtain an IP address from the
network’s BOOTP server.
You can assign IP address parameters using the BOOTP Lite software utility.
Note: You can configure the IP address using Web pages on the modules NOE 771 01, -11
and NWM 100 00.
CAUTION
UNINTENTIONAL OPERATION
If you do not enter the correct address pairs into the BOOTP server, you could
communicate to the wrong device.
z Ensure the MAC address matches the intended IP address in your BOOTP
server.
Having two or more devices with the same IP address can cause unpredictable
operation of your network.
z Ensure that your Ethernet module receives a unique IP address.
Failure to follow this precaution can result in injury or equipment damage.
Using a BOOTP
Server
A BOOTP server is a program that manages the IP addresses assigned to devices
on the network. Your system administrator can confirm whether a BOOTP server
exists on your network and can help you use the server to maintain the adapter’s IP
address.
See Using "BOOTP Lite" to Assign Address Parameters, p. 64.
How an
Unconfigured
("as shipped")
Module Obtains
an IP Address
On startup, an unconfigured NOE 771 xx module will attempt to obtain an IP address
by issuing BOOTP requests. When a response from a BOOTP server is obtained,
that IP address is used. If no BOOTP response is received within two minutes, the
module uses the default IP address derived from its MAC address.
Note: The MAC address is assigned at the factory and is recorded on a label on the front
panel, above the cable connector. This is a unique 48-bit global assigned address. It is set in
PROM. The Ethernet address is recorded on the label in hexadecimal, in the form
00.00.54.xx.xx.xx.
54
Product Description
Connecting to
the Default IP
Address
To connect to the default IP address with your PC, set up an active route from your
PC. To do this with either Windows 95/98/ME/NT/2000 or Windows XP, use the
following procedure. You can use the routes for connecting Ethernet components
with other address ranges.
Step
Action
1
Be sure the NOE module is running.
2
Obtain the default IP address of the NOE derived from its MAC address (e.g.
84.0.0.2).
3
Open an MS-DOS Window.
4
Add an active route for the local NOE by typing
C:\>ROUTE ADD <target> MASK <mask>
<gateway>
e.g.
C:\>ROUTE ADD 84.0.0.0 MASK 255.0.0.0
205.217.193.205
Use the default IP address of the NOE module as target address. Use class A
subnet mask for connecting to every 84.0.0.0 address. The gateway address is the
IP of your PC. The result is that MS Windows will now talk to any address that
starts with an 84 that is directly connected to a hub or switch directly accessible to
your machine, or that can be seen by the route/gateway specified.
5
Confirm that there is a new entry in the active route table by typing C:\>route
print:
The following figure confirms that the new entry was added to the active route
table.
6
Active Routes:
Network Address
0.0.0.0
Netmask
0.0.0.0
Gateway Address
205.217.193.205
Interface
205.217.193.205
Metric
1
84.0.0.0
255.0.0.0
205.217.193.205
205.217.193.205
1
127.0.0.0
255.0.0.0
127.0.0.1
127.0.0.1
1
Verify that a connection is made by typing C:\>ping 84.0.0.2
The following figure shows that the connection is verified.
Reply from 84.0.0.2:
Reply from 84.0.0.2:
Reply from 84.0.0.2:
Reply from 84.0.0.2:
bytes=32
bytes=32
bytes=32
bytes=32
time<10ms
time<10ms
time<10ms
time<10ms
TTL=32
TTL=32
TTL=32
TTL=32
55
Product Description
Specifying
Address
Parameters
Consult your system administrator to obtain a valid IP address and an appropriate
gateway and a subnet mask, if required. Then follow the instructions in the section,
Configuring the Ethernet Address Parameters.
If BOOTP Server
Responds
If the server responds with address parameters, the NOE 771 xx module will use
those parameters as long as power remains applied to the module.
If the server does not respond, the module will retry its request for two minutes.
If BOOTP Server
Does Not
Respond
If no BOOTP response is received, the NOE 771 xx module will use the default IP
Address.
During this time the Run indicator will display a pattern of five flashes for a BOOTP
attempt and six flashes for using the default IP.
NOE 771 xx
Duplicate IP
Address Test
In all cases, when the NOE 771 xx module receives an IP address, it will test for
duplicate addresses by sending broadcast ARP requests three times at 5 second
intervals.
If a Duplicate IP Address is found on the network, the NOE 771 xx will stay off-line
to avoid a network disruption. It will display a pattern of four flashes to indicate a
Duplicate IP Address detection.
Automatic ARP
If there are no replies to its requests, the NOE 771 xx will send automatic ARP three
times at 2 second intervals to announce its presence on the network.
56
Product Description
Establishing the FTP Password
Overview
The following information describes how to set the FTP Password.
Establishing the
FTP Password
The FTP Password is established using the Embedded Web Server. This section
contains information about initially accessing the web server. The first thing the
system administrator should do upon accessing the web server is change the FTP
password. Doing this restricts access to the web server functionality to the system
administrator.
This section contains information on how to access the web server for purposes of
changing the FTP and HTTP passwords. See the chapter Embedded Web Pages
for detailed information about the web server pages and their functionality.
Introduction to
Accessing the
Web Server
Each Quantum 140 NOE 771 xx module contains an embedded Web server, which
allows you to access diagnostics and online configurations for the module and its
associated controller (PLC).
The web pages can only be viewed across the World Wide Web using version 4.0
or higher of either Netscape Navigator or Internet Explorer, both of which support
JDK 1.1.4 or higher.
For information about the additional functionality provided by the FactoryCast
system in the 140 NOE 771 1x modules, see the FactoryCast Manual.
How to Access
the Web Server
Before you can access the module’s home page, you must enter the full IP address
or URL in the Address or Location box in the browser window.
For example: http://hostname (hostname is full IP address or DNS host name.)
After you do this, the Schneider Electric Web Utility home page displays.
57
Product Description
Schneider Web
Utility Home
Page
The following figure shows the Schneider Electric Web Utility home page
Schneider Automation Web Server
Diagnostics and Online Configurations
French
German
Italian
Spanish
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
From this page, you can access the following pages.
z Access the pages to change the FTP password
z Access the pages to change the HTTP password
z Access the pages for diagnostic and configuration information, see Embedded
Web Pages, p. 217 for further information.
58
Product Description
Modifying the
FTP Server
Password
The following steps detail how to link to the correct web page for modifying the FTP
Password
Step
Action
1
Enter the URL, for example, http://hostname/secure/embedded/
ftp_passwd_config.htm
2
The result of step 1 is that the user is requested to supply a user name and password,
as shown in the figure that follows.
The following figure shows the Enter Network Password dialog box.
Enter Network Password
Please enter your authentication information.
Resource:
NOE_security
OK
Cancel
User name:
Password:
Save this password in your password list
3
FTP Username
and Password
Modify Page
Overview
Upon supplying the user name, password, and clicking the <OK> button, the Modify
FTP Server User Name and Password Page displays.
NOTE: The default User Name is USER, and the default Password is USERUSER.
Both should be changed by the system administrator during module installation.
The following figure shows the page used for modifying the FTP user name and
password.
Modify FTP Server User Name and Password
New User Name (1 - 40 char):
New Password (8 - 40 char):
Reset Form
Submit FTP Password Change
Delete FTP Password File
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright 1999,Schneider Automation Inc. All rights reserved
59
Product Description
Change the
Username and
Password
Modify FTP
Server User
Name and
Password
Message
At this point, the system administrator should change the Username and Password
to restrict future access to the system. The following steps should be used.
Step
Action
1
Type in the new Username in the New User Name block
2
Type in the new Password in the New Password block
3
Click on the Submit FTP Password Change button.
The following figure shows the message that is generated if you click on the Submit
FTP Password Change button
Ethernet Configuration
Successfully changed User Name and Password
Please click Reboot Device button to use the new password
Reboot Device
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright „1999,Schneider Automation Inc. All rights reserved
Clicking the Reboot Device button will reset the Username and Password for the
NOE 771 xx board.
Note: The Reboot requires about 40 seconds (with large applications reboot may
require up to one (1) minute).
During the reboot all services provided by the NOE 771 xx are not available.
60
Product Description
Establishing the HTTP Password
Overview
The following information describes how to set the HTTP Password for the NOE 771
0x only.
Modifying the
HTTP Password
The following steps detail how to link to the correct Web page for modifying the
HTTP Password
Step
Action
1
Enter the URL, for example, http://hostname/secure/embedded/
http_passwd_config.htm
2
When you enter the URL, you will be requested to supply a user name and
password.
The following figure displays the Enter Network Password dialog box.
Enter Network Password
Please enter your authentication information.
Resource:
NOE_security
OK
Cancel
User name:
Password:
Save this password in your password list
3
Upon supplying the user name, password, and clicking the OK button, the
Modify HTTP Server User Name and Password page displays.
NOTE: The default User Name is USER, and the default Password is USER.
Both should be changed by the system administrator during module installation.
61
Product Description
Modify Web
Server User
Name and
Password Page
Overview
The following figure shows the Schneider Electric Web page used to modify the
HTTP user name and password.
Modify Web Server User Name and Password
New User Name:
New Password:
Reset Form
Submit Password Change
Delete Password File
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright 1999, Schneider Automation Inc. All rights reserved
Change the
Username and
Password
62
At this point, the system administrator should change the Username and Password
to restrict future access to the system. The following steps should be used.
Step
Action
1
Type in the new Username in the New User Name block
2
Type in the new Password in the New Password block
3
Click on the Submit Password Change button.
Product Description
Modify Web
Server User
Name and
Password
Message
The following figure shows the message that is generated if you click on the Submit
Password Change button.
Ethernet Configuration
Successfully changed User Name and Password
Please click Reboot Device button to use the new Password
Reboot Device
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright 1999, Schneider Automation Inc. All rights reserved
Clicking the Reboot Device button will reset the Username and Password for the
NOE 771 0x board.
Note: The Reboot will take about 40 seconds (with large applications reboot may
require one (1) minute).
During the reboot all services provided by the NOE 771 0x are not available.
63
Product Description
Using "BOOTP Lite" to Assign Address Parameters
Overview
The following information describes how to use the BOOTP Lite utility software.
CAUTION
UNINTENIONAL OPERATION
If you do not enter the correct address pairs into the BOOTP server, you
could communicate to the wrong device.
z Ensure the MAC address matches the intended IP address in your
BOOTP server.
Failure to follow this precaution can result in injury or equipment
damage.
BOOTP Lite
Utility
Instead of a BOOTP server, Schneider Electric’s BOOTP Lite Server Software utility
can be used to provide the IP address, subnet mask, and default gateway to the
NOE 771 xx module.
Refer to the BOOTP Lite Server Software user documentation for instructions
Note: BOOTP Lite Server Software and user documentation are available for
download at www.modicon.com.
64
Product Description
1.4
Customer Support
Customer Support
Customer
Support
If you have any problems, please first consult the documentation listed above or the
MS-Windows documentation.
Please find the nearest Schneider Electric sales office by visiting http://
www.schneider-electric.com. Select your country in the drop-down menu to
find customer support closest to you.
For the most up-to-date NOE Ethernet controller information, please
Step
Action
1
Access the Schneider Electric Web site.
2
Search technical information.
3
Select Quantum from the list of cross-product families.
4
Access either
z resolutions for resolutions to product issues
z product manuals for the most recently published user documentation
z product announcements
65
Product Description
66
Provided Ethernet Services
2
At a Glance
Introduction
This chapter describes the Ethernet services available on NOE 771 x1 and
CPU 651 x0.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Modicon Quantum with Unity Ethernet Services
Page
68
Address Server
70
SNMP and Schneider Private MIB Overview
72
MODBUS Messaging
73
I/O Scanner
74
Global Data
76
Time Synchronization Service
77
Electronic Mail Notification Service
78
Bandwidth Monitoring
79
FTP Server
80
Embedded Web Pages—HTTP Server, Web Configuration and Diagnostics
81
Further Information
83
67
Provided Ethernet Services
Modicon Quantum with Unity Ethernet Services
Table of Ethernet
Services
The Ethernet services add functionality to the system. Some services can be
configured, others require no configuration. Some services provide diagnostic
information. Access to the services is through either a Web page or the Unity Pro
application.
NOE 771 01
NOE 771 11
CPU 651 x0
Web
Unity Pro
Web
Unity Pro
Web
Unity Pro
Diagnostic NA
NA
NA
Configure
Service
Address Server
BOOTP Client
Network Management
Service (SNMP V2 Agent)
Schneider Private MIB
Modbus Messaging
I/O Scanner
Global Data (Pub / Sub)
Unity Pro
Unity Pro
Diagnostic NA
Unity Pro
NA
NA
Configure
Web
Unity Pro
NA
NA
Web
Diagnostic NA
NA
NA
NA
Diagnostic NA
Configure
NA
NA
Configure
Unity Pro
Unity Pro
Unity Pro
Diagnostic Web
Unity Pro
Web
Unity Pro
Web
Unity Pro
Configure
Unity Pro
Unity Pro
Unity Pro
Diagnostic Web
Unity Pro
Web
Unity Pro
Web
Unity Pro
Configure
Web
Unity Pro
Web
Unity Pro
Unity Pro
Diagnostic Web
Unity Pro
Web
Unity Pro
Web
Unity Pro
Time Synchronization
Service
Configure
Web
NA
Diagnostic NA
Web
Unity Pro
NA
Electronic Mail Notification
Service
Configure
Web
Web
Diagnostic Web
Web
Web
Bandwidth Monitoring
Configure
Unity Pro
Unity Pro
Unity Pro
Diagnostic Web
Unity Pro
Web
Unity Pro
Web
Unity Pro
Configure
NA
NA
NA
Diagnostic NA
NA
NA
FTP Server
68
Configure
NA
Web
Provided Ethernet Services
NOE 771 01
NOE 771 11
CPU 651 x0
NA
NA
NA
Diagnostic NA
NA
NA
Configure
Web
Unity Pro
Unity Pro
Diagnostic NA
NA
NA
Configure
Service
HTTP Server
Faulty Device Replacement
(Server)
Hot Standby
Flash File system
FactoryCast Application
Configure
Web
Unity Pro
NA
NA
NA
Diagnostic NA
NA
NA
Configure
NA
NA
NA
Diagnostic NA
NA
NA
NA
Web
NA
Diagnostic NA
Configure
Web
NA
69
Provided Ethernet Services
Address Server
Overview
The following information describes the services provided by the Address Server.
z BOOTP Server
z DHCP Server
The DHCP server responds to both a DHCP and a BOOTP server
BOOTP Server
Note: The BOOTP Server is available on the 140 NOE 771 xx models.
The BOOTstrap Protocol (BOOTP) software, compliant with RFC 951, is used to
assign IP addresses to nodes on an Ethernet network. Devices (hosts) on the
network issue BOOTP requests during their initialization sequence, and a BOOTP
Server that receives the request will extract the required IP address information from
its database and place it in BOOTP response messages to the requesting devices.
The devices will use the assigned IP addresses, received from the BOOTP Server,
for all communication occurring on the network.
Your NOE
BOOTP Server
Your NOE 771 xx module comes supplied with a BOOTP Server. This feature allows
you to provide IP addresses to all the I/O devices being serviced by the NOE 771
xx. Providing a BOOTP Server that is built into your NOE 771 xx module eliminates
the need for an external BOOTP server.
Note: The NOE 771 xx’s BOOTP Server cannot be used to provide its own IP
address.
You can configure your NOE 771 xx’s BOOTP Server from the module’s HTTP Web
page. Configure a 140 CPU 651 x0 using the Unity Pro editors. Configuring allows
you to add to, remove from, and edit devices in the BOOTP Server’s database,
which is maintained in the module’s non-volatile memory.
70
Provided Ethernet Services
DHCP Server
Note: The DHCP Server is available on the 140 NOE 771 x1 models.
Dynamic Host Configuration Protocol (DHCP) is a superset of the BOOTP Protocol.
Your 140 NOE 771 x1 has a DHCP Server. The DHCP Server is compliant with RFC
1531. The DHCP Server can be used to provide the IP configuration to devices
using BOOTP or devices using DHCP.
The DHCP Server has entries that use the MAC address to serve the IP
configuration and entries in the Server that use the role name to serve the IP
configuration. See the Address Server Configuration / Faulty Device Replacement
chapter for details on configuring your NOE’s address Server.
If you are migrating a BOOTP configuration from a 140 NOE 771 x0 module to the
new 140 NOE 771 x1 module, see the Address Server Configuration / Faulty Device
Replacement chapter for details on automatic upgrade of your configuration for the
new DHCP Server.
Note: OPERATING ON A CORPORATE NETWORK
Before placing the NOE on a corporate network, Schneider Electric recommends
that you discuss the installation with your MIS department. It is likely that your
company's corporate network has at least one DHCP Server running already. If the
NOE's DHCP Server is running on the same network, it may disturb the network.
To avoid any possible problem related to the NOE's DHCP Server on the corporate
network, you must ensure that the DHCP Server is not running in the NOE by not
having address entries in the configuration. If there are no configured devices in
the address Server configuration page, then the NOE will not start the DHCP
Server.
71
Provided Ethernet Services
SNMP and Schneider Private MIB Overview
Overview
Simple Network Management Protocol (SNMP) is configured on your NOE.
Introduction
Network management software allows a network manager to
z Monitor and control network components
z Isolate problems and find their causes
z Query devices such as a host computer, routers, switches, and bridges to
determine their status
z Obtain statistics about the networks to which they attach
Simple Network
Management
Protocol
Your NOE module is configured with the Simple Network Management Protocol
(SNMP), which is the standard protocol used to manage a local area network (LAN).
SNMP defines exactly how a manager communicates with an agent.
The SNMP defines the format of the requests that a manager sends to an agent and
the format of the replies that the agent returns to the manager.
The MIB
Each object to which SNMP has access must be defined and given a unique name.
Both the manager and agent programs must agree on the names and the meanings
of the fetch and store operations. The set of all objects SNMP can access is known
as a Management Information Base (MIB).
The Private MIB
Schneider obtained a private MIB, Groupe_Schneider (3833). Under the Groupe
Schneider private MIB is a Transparent Factory Ethernet (TFE) private MIB. The
Transparent Factory SNMP embedded component controls the Schneider private
MIB function.
72
Provided Ethernet Services
MODBUS Messaging
Overview
The following information describes the functionality of the MODBUS/TCP Server.
Introduction Client
All Modicon Quantum Ethernet modules provide the user with the capability of
transferring data to and from nodes on a TCP/IP network using a communication
instruction. All PLCs that support networking communication capabilities over
Ethernet can use either the MSTR Ladder Logic instruction to read or write controller
information or IEC communication blocks.
Introduction Server
Using the standard MODBUS/TCP protocol, all Modicon Quantum Ethernet
modules provide access to controller data. Any device, PC, HMI package, another
PLC, or any MODBUS/TCP compliant device, can access data from the PLC. The
MODBUS/TCP server also allows programming panels to log into the controller over
Ethernet.
Limitations
The Ethernet module supports up to 64 simultaneous MODBUS/TCP server
connections. To guarantee consistency of changes to the controller configuration,
the Ethernet module allows only one Programming Panel to be logged in at a time.
The following MODBUS/TCP commands are supported by the Ethernet module:
z Read Data
z Write Data
z Read/Write Data
z Get Remote Statistics
z Clear Remote Statistics
z MODBUS 125 Commands (used by programming panels to download a new
Exec to the NOE)
Performance
The following table shows the performance characteristics of the Ethernet module’s
MODBUS/TCP Server.
Parameter
Value
Typical Response Time (ms)
0.6
Number of MODBUS connections
(Client and Server)
64 (NOE 771 x1, NWM 100 00, HE CPU 651 x0)
16 Client (NOE 771 x0)
32 Server (NOE 771 x0)
Number of simultaneous login channels
1
Note: Ethernet module’s MODBUS/TCP performance measurements are made
with a Modicon Quantum 140 CPU 534 14 PLC.
73
Provided Ethernet Services
I/O Scanner
Introduction
The functionality of your Ethernet module is further enhanced by the addition of an
I/O Scanner, which you can configure with either the Schneider Electric
programming panels or on the Ethernet module’s embedded Web page.
I/O Scanner
Features
In 2004 Schneider Electric enhanced the I/O scanner capabilities by offering:
74
Feature
Availability
Improvement
Description
Improved Timeout
and Retry
Transmission
algorithm
Unity
Concept
ProWORX
Improves TCP
connection
management
2004 version uses a variable
timeout. Older versions used
a fixed timeout.
Difference: Faster
retransmission rates
Enable/Disable I/O
Scanner entry
Unity
Concept
Reduces network
traffic volume
Use the ‘Device Control
Block’
z Set = 0 Enable channel
for normal data exchange
z Set = 1 Disable channel
Note: Concept Users
Concept uses diagnostic
words.
Set = FF Disable channel
Send Modbus
requests across a
router
Unity
Concept
ProWORX
Allows routers to
Automatic
connect remote I/O
devices to a controller
Dynamic TCP port
allocation
Unity
Concept
ProWORX
Improves connection/ Reserves TCP client ports
disconnection
3072 (0xC00) through 4992
performance
(0x1380)
Allocates ports dynamically
Repetition rate
display
Unity
Check status using
GUI
Status displays in I/O
Scanning tab of module
editor
Provided Ethernet Services
I/O Scanner
Parameters
Functionality of the I/O Scanner.
Parameter
Value
Max. No. of Devices
64: 140 NOE 771 00 (Version 2.2 or earlier)
128: 140 NOE 771 00 (Version 3.0 or later), 140 NOE 771 01,
and 140 NOE 771 11 only
128: HE CPU 651 x0
Max. No. of Input Words
4000
Max. No. of Output Words 4000
Health Timeout Value
User configured (1 ms to 2 s in 1 ms increments)
Last Value (Input)
User configured (Zero or Hold)
IP Address
User configured
IP address of scanned device (Slave IP)
Local and Remote
Register Reference
User configured
Repetition Rate
User configured
Unit ID
User configured
Configure ID only if using a bridge
Operation through a
bridge
Modbus bridge: Supported
Modbus Plus bridge: Supported
Refer to the section I/O Scanner Concepts, p. 166 to learn how to configure the
MODBUS I/O Scanner.
Performance
Refer to the appendix for detailed performance data.
75
Provided Ethernet Services
Global Data
Overview
Global Data service is a real time Publisher/Subscriber mechanism providing the
most efficient data exchange for PLC application coordination.
Devices supporting Global Data are arranged in a distribution group for the purpose
of application variable exchange and synchronization. Each Global Data device can
publish up to one network (application) variable and subscribe up to 64 network
(application) variables.
The Quantum NOE’s embedded Web Global Data Configuration Page provides a
configuration screen to determine which and how many application variables are
exchanged with this service. After configuration, the exchanges between all stations
belonging to the same distribution group are done automatically.
The Global Data service uses %MW words (4x registers) for Global Data
exchanges.
Key Features of
Global Data
The main features for Global Data are:
z One Publisher and many Subscribers
z A device can publish one network variable of up to 512 %MW words (4x registers)
z A device can subscribe to several network variables of up to 2048 %MW words
(4x registers)
z A device subscribes to the complete network variable
z One distribution group per network IP address
z Application defined publication rate
z Up to 64 Global Data network variables (numbered from 1 to 64) can be part of
the data distribution group
z An NOE has only one multicast address; consequently, it can only publish and
subscribe inside the group
z A device can participate in several distribution groups by using multiple NOEs in
the rack
Global Data has an advantage over Client / Server services when more than one
Subscriber is receiving the same data since only one transaction is necessary for all
Subscribers to receive the data.
This advantage offers two benefits:
z Reduce overall network traffic
z Ensure tighter synchronization of multiple subscribers
76
Provided Ethernet Services
Time Synchronization Service
General
The time service synchronizes computer clocks over the Internet. For example, the
time of one client is synchronized either with another server or to a referenced time
source like a radio or satellite receiver.
Typical time service configurations utilize multiple redundant servers and diverse
network paths to achieve high accuracy and reliability. Time service accuracy can
be within a millisecond on LANs and up to a few tens of milliseconds on WANs.
Use the time service for
z event recording—sequence events
z event synchronization—trigger simultaneous events
z alarm and I/O synchronization—time stamp alarms
Time
Synchronization
and Time Stamps
On an Ethernet network, all controllers should be synchronized with the same clock
time, which is provided by an NTP server. In each application program, events or
application data (IO values for example) can be time stamped using the application
stacks.
The Modicon Quantum Ethernet interface module, a NOE 771 11, connects to an
NTP time server and provides the source-time synchronization signal, which is sent
to the CPU.
To read the clock, a function block is used in the controller’s project (application
program).
CPS
CPU
NOE
Clock
System
Counter
NTP Request
NTP
Client
R_NTPC
EN0
EN
NTP
Server
Ethernet
Network
NTP Response
Modicon Quantum System
OUT1
OUT2
STATUS
77
Provided Ethernet Services
Electronic Mail Notification Service
General
The electronic mail notification service allows controller-based projects to report
alarms or events. The automation controller monitors the system and can
automatically create an electronic mail message alert with data, alarms, and/or
events. Mail recipients can be either local or remote.
z Based on predefined events or conditions, messages are created using the
MSTR function block.
z The email message is constructed from predefined headers plus variables and
text (a maximum of 238 bytes). This message is sent directly from the automation
system to the local email server.
z Mail headers contain common predefined items—recipient list, sender name, and
subject. These items can be updated by an authorized administrator.
Mail Service
Client
The NOE and 140 CPU 651 x0 modules include an SMTP client. When the module
receives a specific request from the controller, the module sends an email message
to the mail server.
CPS
CPU
NOE
SMTP
Server
MSTR
Email
OK or NOK
SMTP
Client
78
Ethernet
Provided Ethernet Services
Bandwidth Monitoring
Overview
Bandwidth Monitoring allows the user to monitor the NOE’s CPU allocation for each
of the following services: Global Data, I/O Scanning, and Messaging. The
Bandwidth Monitoring service retrieves workload data and returns one of two pieces
of information: whether the module has free resources or whether the module is
working at capacity. Knowing the resource allocation helps you:
z Decide about allocating your resources
z Determine the number of NOEs needed in a system
Available
Services
The services accessed and monitored are:
z Global Data
z I/O Scanner
z Modbus Messaging
If the user want to use Bandwidth Monitoring, he do not need to develop a new set
of access functions. The actual NOE CPU load is computed each second.
Bandwidth
Monitoring Load
Rates
The Bandwidth Monitoring service checks once a second and computes four (4)
values in private data:
z Percentage of NOE’s CPU allocated to Global Data
z Percentage of NOE’s CPU allocated to the I/O Scanner
z Percentage of NOE’s CPU allocated to Messaging
z Percentage of NOE’s CPU allocated to other services and idle
Results are returned as percentages. CPU time spent in other services is shown as
"Other" or "Free." Bandwidth Monitoring uses the same functions as used by SNMP.
The three service rates, Global Data, I/O Scanner, and Messaging, are computed
using the following formula:
(Current load * 100) / Maximum Load
Table of Maximum Load Rates
Diagnostic Service
Workload Data Returned
Maximum load
for NOE 771 x1
Global Data
Number of published variables per second
800
I/O Scanner
Number of transactions per second
4200
Messaging
Number of messages treated per second
410
The current load is computed dynamically.
Note: The loads are dependent on controller scan time. Each application has an expected
scan time. Therefore, when evaluating the loads, the user should ensure that the controller
scan time is set to the expected scan time for the application being modelled.
79
Provided Ethernet Services
FTP Server
Overview
The following information describes the services provided by the File Transfer
Protocol (FTP) Server. The FTP server is available on all NOE 771 xx and CPU 651
x0 modules.
FTP Server
The NOE 771 xx’s and CPU 651 x0’s FTP Server is available as soon as the module
receives an IP address. Any FTP client can log on to the module, which requires the
client use the correct user name and password.
The FTP Server provides the following services:
z Update the NOE’s firmware by downloading a new Exec
z Provides error log visibility by uploading error log files
z Upload/download BOOTP Server and SNMP configuration files
Note: Only one FTP client per module.
The FTP Server is protected with a default user name and password.
Default user name
USER
Case sensitive
Default password
USERUSER
Case sensitive
Refer to Establishing the FTP Password, p. 57 for instructions about how to change the
password, and how to add or delete user names to the FTP Server.
80
Provided Ethernet Services
Embedded Web Pages—HTTP Server, Web Configuration and Diagnostics
HTTP Server
The Modicon Quantum with Unity Ethernet modules’ Hypertext Transport Protocol
(HTTP) server is available as soon as the module receives an IP address.
Use the HTTP Server
1. with Internet Explorer version 4.0 or higher
2. to view:
z Module’s Ethernet statistics
z Controller and I/O information
z BOOTP/DHCP/FDR (Faulty Device Replacement) server information
z Global Data (Publish / Subscribe) information
3. to configure the module’s BOOTP/DHCP/FDR server and SNMP agent
Note: JRE 1.4.2_04 or higher plug-in required with Internet Explorer
The HTTP server is protected with a default user name and password.
Default user name
USER
Case sensitive
Default password
USER
Case sensitive
Change either user name or password via the Configuration page on the Ethernet modules’
Web Embedded Pages. (See Establishing the HTTP Password, p. 61)
For the NOE 771 11 modules, user name and passwords can be changed via the
FactoryCast Configurator.
Note: CONNECTIONS
The NOE 771 xx and CPU 651 xx support a maximum of 32 HTTP simultaneous
connections.
Browsers may open multiple connections so 32 HTTP connections does not
indicate 32 simultaneous users.
Note: DOWNLOADED WEB PAGES
The NOE 771 00 and NOE 771 01 modules do not support user downloaded Web
pages. You will need to purchase either the NOE 771 10, NOE 771 11, or the NWM
100 00 module to support user downloaded Web pages.
81
Provided Ethernet Services
Web
Configuration
The embedded Web server provides Web pages to configure the following
Transparent Factory / Real Time services.
Service
Description
Global Data diagnostics
z
z
z
z
z
z
I/O Scanning diagnostics
status of all global data services
status of all subscribed and published variables
publication/subscription rate
status of all I/O scanning services
status of individual scanned devices
actual I/O scanning rate
Messaging diagnostics
diagnostic information for port 502 messaging
Time Synchronization diagnostic
z
z
z
z
z
z
Electronic Mail Notification diagnostic
Bandwidth Monitoring
status of client and link to the server
date and time
status of daylight savings time (DST) option
status of SMTP server
track messages sent and received
track errors
throughput measure of NOE by service
Note: All these pages are protected by the general HTTP password.
82
Provided Ethernet Services
Further Information
Hot Standby
The Ethernet Hot Standby system consists of two identical Modicon Quantum
systems each containing a Modicon Quantum Hot Standby with Unity controller (140
CPU 671 x0), a remote I/O head, no more than six NOE771 xx’s, and a power
supply. The Hot Standby modules are connected to each other via a fiber optic
cable. Both remote I/O heads are connected to the remote I/O network and to each
other.
Schneider Electric recommends
1. remote I/O network use redundant cables
z drops are not redundant
2. switch connects the NOEs to the network
switches available
z 499NES17100
z 499NOS17100
FactoryCast and
User
Customizable
Web Pages
FactoryCast is a software package that you use to customize a Web site on the
embedded Web server module. The site can be accessed via a browser to view and
modify data from a Modicon Quantum with Unity controller (PLC).
FactoryCast provides all the Web pages and Java applets you need to view run-time
data from your controller. You can use the FactoryCast default Web site simply by
configuring the module and accessing it with a browser over an intranet.
The NOE 771 10, -11 and 140 NWM 100 00 modules provide the possibility to add
your own Web pages to the site.
Flash File
System
The NOE 771 xx modules are equipped with a Flash File System, which allows
changing or updating the executive, kernel, and Web site files by an upload.
83
Provided Ethernet Services
84
Modicon Quantum with Unity
Ethernet Modules Services
II
At a Glance
Purpose
This part introduces the Ethernet services available with Modicon Quantum with
Unity Ethernet modules.
What's in this
Part?
This part contains the following chapters:
Chapter
3
Chapter Name
Start Communication with Unity Pro
Page
87
85
Ethernet Services
86
Start Communication with
Unity Pro
3
At a Glance
Introduction
This chapter presents how to start the configuration of an Ethernet network within
Unity Pro.
What's in this
Chapter?
This chapter contains the following sections:
Section
Topic
Page
3.1
How to Configure the Communication
88
3.2
Unity Soft Communication Links
93
3.3
Selecting the Ethernet Module
97
3.4
Selecting the Ethernet Coprocessor
102
87
Start Communication with Unity Pro
3.1
How to Configure the Communication
Overview
Overview
This section describes how to configure the communication.
What's in this
Section?
This section contains the following topics:
88
Topic
Page
Add a New Network to the Communication Folder
89
Configure Network
90
Properties of a Network
91
Delete an Existing Network Folder
92
Start Communication with Unity Pro
Add a New Network to the Communication Folder
Add a New
Network to the
Communication
Folder
After starting a new application, the Communication folder under Station tree
branches the Network folder and the Routing table folder (only on Premium
platform). These two folders are empty. Under the Network folder, the user can
insert the networks by menu. A click on the right mouse-button above Network pops
up a contextual menu. The user selects the type of network he wants to add. For
easier use, a network name will be suggested with the prefix of the network type
(Ethernet_1 or Modbus+_1). By choosing a new network the next available number
for the network is chosen automatically like e.g. Ethernet_1 then Ethernet_2 and so
on. At any moment, the user may rename any NetLink.
The user can also attach a comment that describes each configured network. The
OK button adds the network as subfolder.
The names of network nodes are also called NetLink. These are the names of
logical networks.
Station
Configuration
Derived Data Types
Derived FB Types
Variables & FB instances
Communication
Networks
Program New Network
Add User Directory
Animation Tables
Operator Screens
Add Hyperlink
Documentation
Zoom out
1
Add Network
Network
List of available Networks :
Station
Configuration
Derived Data Types
Derived FB Types
Variables & FB instances
Communication
Networks
Ethernet_1
Program
Animation Tables
Operator Screens
Documentation
Comment
Ethernet
Ethernet_1
2
OK
Cancel
Help
89
Start Communication with Unity Pro
Configure Network
Configure
Network
On the network folder, by a double-clicking action or by the Open item on contextual
menu, the editor of the corresponding communication screen is opened in order to
set the specific network services.
The figure shows the contextual menu to start network properties
Station
Configuration
Derived Data Types
Modbus+_1
Derived FB Types
Open
Variables & FB instances
Export
Communication
Delete
Del
Networks
Add user directory
Ethernet_1
Add Hyperlink
Program
Zoom out
Animation Tables
Properties
Alt+Enter
Operator Screens
Documentation
90
Start Communication with Unity Pro
Properties of a Network
Properties of a
Network
The contextual menu proposes the user to see again the properties of a configured
network. Here, the user can change the NetLink name and the associated comment.
The figure shows the Ethernet property window
Station
Configuration
Derived Data Types
Derived FB Types
Variables & FB instances
Communication
Properties Network Ethernet_1
Network
Comment
List of available Networks :
Networks
Ethernet_1s_1
Open
Program
Export
Animation TablesDelete
Operator Screens
Add user directory
Documentation
Add Hyperlink
Ethernet
Del
Zoom out
Properties
Alt+Enter
Change Name :
Ethernet_1
OK
Cancel
Help
91
Start Communication with Unity Pro
Delete an Existing Network Folder
Delete an
Existing Network
Folder
With a right-mouse-click above the network folder, a contextual menu appears. Here
the user is able to delete the network configuration. In this case, the subfolder of the
network will also be removed in application browser.
Station
Configuration
Derived Data Types
Derived FB Types
Variables & FB instances
Communication
Networks
Delete Network...
Remove this Network ?
Ethernet_1
OK
Cancel
Ethernet_1
Note: If this removed network was previously attached to a communication
module, this module loses its link and it will work with its default parameters.
92
Start Communication with Unity Pro
3.2
Unity Soft Communication Links
At a Glance
Overview
This section presents the principle of communication implementation and describes
the relationship between software configuration of networks and the hardware
configuration of the network controllers.
What's in this
Section?
This section contains the following topics:
Topic
Communication Configuration Principle
Page
94
Link between Configuration and Communication
95
Link between Data and Communication
96
93
Start Communication with Unity Pro
Communication Configuration Principle
Introduction
The configuration of communication links between different devices with Unity Soft
includes three different configuration parts.
z Configuration of the Network Controller
z Configuration of the Logical Network
z Configuration of Network Variables
Configuration
The Communication Configuration supports the "Free Mode" of Unity Soft. That
means the user can first configure the module and then the Communication or the
user can configure the communication and then the module.
This will be provided through a NetLink that must be selected in the module
configuration. The network variables including in the VAR folder are linked with a
group name that defines an IP domain over Internet network.
The illustration shows the three parts involved in communication configuration:
VAR
Gr
ou
p
va s of
ria n
bl etw
es o
rk
STATION
Network
Variables
VAR
Data
base
Network
Parameters
COMM
Data
base
Module
Parameters
CONF
Data
base
COMM
L
ne og
tw ica
or l
ks
GROUP NAME
CONF
94
Ne
co two
nf rk
ig m
ur o
at du
io le
ns
NET LINK
Start Communication with Unity Pro
Link between Configuration and Communication
NetLinks
During Unity Pro application design, the NetLinks are created and inserted on subfolder Communication under Network. These are the names of logical networks.
Under configuration folder, on the communication module node included in the
current station, the list of existing NetLinks is proposed to select and attach one
network to one module. Only the NetLink that can be managed by this module, are
displayed in the list box on module configuration screen. No NetLink can be edited
and created here (no edit box), but this list contains at least the No_Link field.
The following figure shows the window for the Ethernet link for the Quantum NOE
module.
UNITY-Station
Variables
Communication
Network
Modbus+_A
Ethernet_1
Ethernet_2
Configuration
0 : X Bus
0 : PremiumDrop
0 : TSX RKY 12EX
ef
Attaching a
NetLink to a
Module
0:
1:140 CPU 534
2:
3:
4:140 NOE 771 11
5:
6:
1.4 : SubsetENETLF
ENETFE
Overview
General
Please choose a Network
No Link
No Link
ETHERNET_1
When a network is attached to a module, the icon of the corresponding node is
changed and the network editor displays the address of the module in the rack .
The Icon in the Network folder indicates whether the link is attached to a module or
not:
Icon when no communication module is attached to the NetLink
Icon when a communication module has been attached to the NetLink
95
Start Communication with Unity Pro
Link between Data and Communication
The groups of Ethernet network variables are created in the Ethernet network
communication folders. An IP domain determines a group. In Unity Pro, one network
can support only one group.
In Data Editor, the list of all current groups is provided to select in which group each
Ethernet network variables is included. Nevertheless, the group field is also a free
entry editing box, in order to give a group name not yet defined in communication
folder. The build step checks this link.
The illustration shows corresponding fields in Communication configuration and the
Data Editor:
Network
Variables and
Groups
Ethernet_PLC
Structural view
Station
Configuration
Derived Data Types
Derived FB Types
Variables
Communication
Networks
Ethernet_plant
Ethernet_PLC
Program
Animation Tables
Operator Screens
Documentation
Global data configuration
Health time out 300
Distribution period 2
ms
scan
Group address 239 . 255 . 255 . 255
Group name Group_1
Ethernet_plant
Messaging
IO Scanning Address Server
SNMP
Global data
Bandwidth
Global data configuration
Health time out 250
Distribution period 5
ms
scan
Group address 239 . 255 . 255 . 255
Group name Group_2
010 Data Editor
Variables
Filter
DDT Types
Name
Name
GD_MW500
GD_MW893
X_temperature
Valve12
X_Counter
P_x1
Ethernet
96
Function Blocks
*
Type
Array[1...3]
Array[1...10
Int
Valve
Int
Int
010 Data Editor
DFB Types
EDT
Address
%MW500
%MW893
%MW22
%MW381
%MW100
%MW200
Ethernet
Value Global...
0 SUB
0 PUB
0 PUB
0 SUB
0 SUB
100 NO
DDT
Group
Group_1
Group_2
Group_1
Group_1
Group_2
IODDT
Enet ID
1
7
8
7
10
Start Communication with Unity Pro
3.3
Selecting the Ethernet Module
At a Glance
Introduction
This chapter contains the software page Selecting the Quantum NOE/NWM
Ethernet Module.
The module families are the communication modules 140 NOE 771 xx, 140 NWM
100 00 and the processor module CPU 651 x0.
Note: The webpage settings described only apply to the communication modules.
The processor modules only offer the possibility for diagnostics via the web.
What's in this
Section?
This section contains the following topics:
Topic
Selecting the Quantum NOE Ethernet Module
Page
98
IP Configuration
100
Quantum NOE Ethernet Messaging Configuration
101
97
Start Communication with Unity Pro
Selecting the Quantum NOE Ethernet Module
General
Description
After configuring Ethernet communication (see: Add a new network to the
Communication folder, p. 89) the Ethernet module parameters can be configured.
When you select the model family, all the corresponding communication module
configuration options are displayed automatically. The module services allow the
following settings to be made.
Table of module service configuration options:
Setting
Description
No
Setting deactivated
Yes
Setting activated. Parameters are set using the Unity Pro menu window.
Web
Setting activated. Parameters are set using the configured NOE Web pages.
Unity Pro menu window deactivated.
Not available for every model family.
Note: The availability of the displayed settings depends on the selected model
family and can vary.
The screen shot shows an example of the menu window of the Ethernet module
NOE 771 x1 (TCP/IP 10/100 Regular connection).
ETHERNET_1
Model Family
Modul Address
Rack
TCP/IP 10/100 Regular Connection
Module
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
Gateway Address
0 . 0 . 0 . 0
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Parameter description
98
Parameter
Description
Model family
Quantum NOE Ethernet Module settings
Slot
Not used
Module services
For module service configuration options, see above.
IP address of the module
Overview of the IP address parameter set.
Start Communication with Unity Pro
After selecting the model family TCP/IP 10/100 Regular Connection, the following
mask appears. The image also displays the activated module services.
ETHERNET_1
Model Family
Modul Address
Rack
TCP/IP 10/100 Regular Connection
Module
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
IP Confugration
Access Control
Gateway Address
0 . 0 . 0 . 0
I/O Sanning
Global Data
SNMP
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Address Server
Bandwidth
IP Address Configuration
Configured
IP adress
139 . 124 . 10 . 14
Subnetwork mask
255 . 255 . 0 . 0
Gateway address
139 . 124 . 10 . 1
From a server
WEB Configurator
Ethernet configuration
Ethernet II
802.3
Note: The availability of the displayed register depends on the selected model
family and can vary.
After selecting the Yes option in module services, the tab corresponding to the
module is activated.
99
Start Communication with Unity Pro
IP Configuration
General
Description
The IP configuration tab enables you to configure the IP address settings. The
settings are activated after the connection to the hardware and the configuration is
downloaded to the PLC in the Quantum NOE Ethernet module.
The diagram shows the IP configuration for the Quantum NOE Ethernet model
family.
ETHERNET_1
Model Family
Modul Address
Rack
TCP/IP 10/100 Regular Connection
Module
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
IP Confugration
Access Control
Gateway Address
0 . 0 . 0 . 0
I/O Sanning
Global Data
SNMP
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Address Server
Bandwidth
IP Address Configuration
Configured
IP adress
139 . 124 . 10 . 14
Subnetwork mask
255 . 255 . 0 . 0
Gateway address
139 . 124 . 10 . 1
From a server
WEB Configurator
Ethernet configuration
Ethernet II
802.3
Description of the selection properties
Selection
Description
Configured
Activate the IP address, Subnet mask and Gateway address. The
data is activated after the configuration is downloaded to the PLC.
Client / Server
The Quantum NOE Ethernet module receives its IP address
parameter through a BOOTP server on startup.
Web configuration
The IP address parameter settings are made on the embedded
Web page of the Quantum NOE Ethernet module.
Ethernet configuration Select the default protocol as Ethernet or 802.3.
100
Start Communication with Unity Pro
Quantum NOE Ethernet Messaging Configuration
Introduction
Ethernet Messaging gives the user the opportunity to send and receive Ethernet
messages. Data traffic is handled by the Client / Server procedure.
The illustration shows the Ethernet Messaging dialog box.
ETHERNET_1
Model Family
TCP/IP 10/100 Regular Connection
Modul Address
Rack
Module
Module IP Address
IP Address
0 . 0 . 0 . 0
IP Configuration
Subnetwork Mask
0 . 0 . 0 . 0
Access Control I/O Scanning
Gateway Address
0 . 0 . 0 . 0
Global Data
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
SNMP Address Server Bandwidth
Connection configuration
1
2
3
4
5
6
7
8
9
10
11
12
Access Slave IP Address
139.124.10.11
100.32.0.12
100.32.0.11
100.32.0.10
100.32.0.14
139.124.10.12
139.124.10.13
100.32.0.12
100.32.0.18
100.32.0.10
139.124.10.15
Parameter description
Setting
Description
Connection
configuration
Activates general data transfer
Access
Activates data transfer between specific nodes.
Slave IP address
Defines the node for the Ethernet Messaging procedure.
101
Start Communication with Unity Pro
3.4
Selecting the Ethernet Coprocessor
At a Glance
Introduction
This section describes configuring the Modicon Quantum with Unity coprocessor,
140 CPU 651 x0.
What's in this
Section?
This section contains the following topics:
Topic
Selecting the Modicon Quantum with Unity Ethernet Controller
102
Page
103
Configuring the IP Address of the Ethernet Controller
105
Modicon Quantum with Unity Ethernet Controller Messaging Configuration
106
Start Communication with Unity Pro
Selecting the Modicon Quantum with Unity Ethernet Controller
General
Description
After configuring Ethernet communication (See Add a new network to the
Communication folder, p. 89), configure the Ethernet module parameters.
When you select the model family, all the corresponding communication-module
configuration options display automatically. The module services allow the following
settings to be made.
Setting
Description
No
Setting deactivated
Yes
Setting activated. Parameters are set using the Unity Pro menu window.
Note: The availability of the displayed settings varies and depends on the selected
model family.
The screen shot shows an example of the menu window of the Ethernet module
CPU 651 x0 (TCP/IP 10/100 Extended connection).
ETHERNET_1
Model Family
TCP/IP 10/100 Extended Connec-
Module Address
Rack
Mod-
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
Gateway Address
0 . 0 . 0 . 0
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Parameter description
Parameter
Description
Model family
Modicon Quantum with Unity Ethernet module settings
Slot
Not used
Module services
For module service configuration options, see above.
IP address of the module
Overview of the IP address parameter set.
103
Start Communication with Unity Pro
After selecting the model family TCP/IP 10/100 Extended Connection, the
following mask appears. The image also displays the activated module services.
ETHERNET_1
Model Family
TCP/IP 10/100 Extended Connec-
Module Address
Rack
Mod-
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
IP Configuration Access Control I/O Scan-
Gateway Address
0 . 0 . 0 . 0
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Global Data SNMP Address Server Bandwidth
IP Address Configuration
Configured
IP address
13 . 12 . 10 . 14
Subnetwork mask
25 . 25 . 0 . 0
Gateway address
13 . 12 . 10 . 1
From a server
WEB Configurator
Ethernet configuration
Ethernet II
802.3
Note: The availability of the displayed register depends on the selected model
family and can vary.
After selecting the Yes option in module services, the tab corresponding to the
module is activated.
104
Start Communication with Unity Pro
Configuring the IP Address of the Ethernet Controller
General
Description
The IP configuration tab enables you to configure the IP address settings. The
settings are activated after the connection to the hardware and the configuration is
downloaded to the Modicon Quantum with Unity Ethernet controller, 140 CPU 651
x0.
The diagram shows the IP configuration for the Modicon Quantum with Unity
Ethernet controller, 140 CPU 651 x0.
ETHERNET_1
Model Family
TCP/IP 10/100 Extended Connec-
Module Address
Rack
Mod-
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
IP Configuration Access Control I/O Scan-
Gateway Address
0 . 0 . 0 . 0
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Global Data SNMP Address Server Bandwidth
IP Address Configuration
Configured
IP address
13 . 12 . 10 . 14
Subnetwork mask
25 . 25 . 0 . 0
Gateway address
13 . 12 . 10 . 1
From a server
WEB Configurator
Ethernet configuration
Ethernet II
802.3
Description of the selection properties
Selection
Description
Configured
Activate the IP address, Subnet mask and Gateway address. The
data is activated after the configuration is downloaded to the
controller.
Client / Server
The Modicon Quantum with Unity Ethernet controller receives its
IP address parameter through a BOOTP server on startup.
Web configuration
The IP address parameter settings are made on the embedded
Web page of the Modicon Quantum with Unity Ethernet controller.
105
Start Communication with Unity Pro
Modicon Quantum with Unity Ethernet Controller Messaging Configuration
Introduction
Send and receive messages though the Ethernet. Data traffic is handled by the
Client / Server procedure.
The illustration shows the Ethernet Messaging dialog box.
ETHERNET_1
Model Family
TCP/IP 10/100 Extended Connec-
Module Address
Rack
Module
Module Utilities
Access Control
YES
Module IP Address
IP Address
0 . 0 . 0 . 0
Subnetwork Mask
0 . 0 . 0 . 0
IP Configuration Access Control I/O Scan-
Gateway Address
0 . 0 . 0 . 0
Global Data SNMP
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
Address
Bandwidth
Connection configuration
1
2
3
4
5
6
7
8
9
10
11
12
Access Slave IP Address
139.124.10.11
100.32.0.12
100.32.0.11
100.32.0.10
100.32.0.14
139.124.10.12
139.124.10.13
100.32.0.12
100.32.0.18
100.32.0.10
139.124.10.15
Parameter description
106
Setting
Description
Connection configuration
Activates general data transfer
Access
Activates data transfer between specific nodes.
Slave IP address
Defines the node for the Ethernet Messaging procedure.
Using the Modicon Quantum with
Unity Ethernet Services
III
At a Glance
Purpose
This part describes how to use the Ethernet services available on Modicon Quantum
with Unity Ethernet modules.
What's in this
Part?
This part contains the following chapters:
Chapter
Chapter Name
Page
4
Transferring Data using Communication Blocks
109
5
Global Data (Publish / Subscribe) Utility
149
6
I/O Scanner
165
7
Address Server Configuration / Faulty Device Replacement
171
8
Network Management Service (SNMP)
183
Time Synchronization Service
203
Electronic Mail Notification Service
209
9
10
11
Embedded Web Pages
217
12
Hot Standby
265
107
Using Ethernet Services
108
Transferring Data using
Communication Blocks
4
At a Glance
Introduction
This chapter describes how to transfer data to and from nodes on a TCP/IP network
using communication blocks. You transfer the data using either a special MSTR
instruction (the Master instruction of the 984 Ladder Logic instruction set) or an IEC
Logic function. Included in this chapter are the operational statistics and error codes
for reading and writing the controller information.
109
Transferring Data Using Communication Blocks
What's in this
Chapter?
110
This chapter contains the following topics:
Topic
Page
CREAD_REG
111
CWRITE_REG
114
READ_REG
117
WRITE_REG
120
TCP_IP_ADDR
123
MBP_MSTR
125
MSTR Function Error Codes
129
Read and Write MSTR Operations
133
Read/Write MSTR Operation (FC 23)
134
Get Local Statistics MSTR Operation
135
Clear Local Statistics MSTR Operation
136
Get Remote Statistics MSTR Operation
137
Clear Remote Statistics MSTR Operation
138
Peer Cop Health MSTR Operation
139
Reset Option Module MSTR Operation
141
Read CTE (Config Extension Table) MSTR Operation
142
Write CTE (Config Extension Table) MSTR Operation
144
TCP/IP Ethernet Statistics
146
Transferring Data Using Communication Blocks
CREAD_REG
Function
Description
This Function block reads the register area continuously. It reads data from an
addressed node via TCP/IP-Ethernet.
EN and ENO can be projected as additional parameters.
Note: When programming a CREAD_REG function, you must be familiar with the routing
procedures used by your network.
Note: For technical reasons, this function block does not allow the use of programming
languages ST and IL.
Representation
Block Representation
CREAD_REG
DINT
INT
WordArr5
Parameter
Description
Elementary
Description for
WordArr5 with
TCP/IP Ethernet
SLAVEREG
NO_REG REG_READ
AddrFld
STATUS
WORD
WORD
Description of Parameters
Parameter
Data Type
Meaning
SLAVEREG
DINT
Offset address of the first 4x register in the slave to be read from
NO_REG
INT
Number of registers to be read from slave
AddrFld
WordArr5
Data structure describing the TCI/IP address
REG_READ
WORD
First 4x area register for read values
STATUS
WORD
Error code, see Runtime errors
Elementary description for WordArr5 with TCP/IP Ethernet
Element
Data Type Meaning
WordArr5[1] WORD
Low value byte: MBP on Ethernet Transporter (MET) mapping
index
High value byte: Slot of the NOE module
WordArr5[2] WORD
Byte 4 (MSB) of the 32-bit destination IP address
WordArr5[3] WORD
Byte 3 of the 32-bit destination IP address
WordArr5[4] WORD
Byte 2 of the 32-bit destination IP address
WordArr5[5] WORD
Byte 1 (LSB) of the 32-bit destination IP address
111
Transferring Data Using Communication Blocks
Function Mode of
the CREAD_REG
Block
Although a large number of CREAD_REG function blocks can be programmed, only
sixteen read operations may be active at the same time. In such a case it is
insignificant whether they are the result of this function block or others (e.g.
MBP_MSTR, MSTR, READ_REG). All function blocks use one data transaction
path and require multiple cycles to complete a job.
Note: A TCP/IP communication between a Quantum PLC (NOE 771 xx) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
Note: A TCP/IP communication between a Quantum PLC (NOE 211 00) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
The entire routing information is contained in data structure WordArr5 of input
AddrFld. The type of function block connected to this input and thus the contents of
the data structure depends on the network used.
Please use:
z TCP/IP EtherNet the function block TCP_IP_ADDR
Note: For experts: The WordArr5 data structure can be used with constants as
well.
Note: This function block puts a heavy load on the network; therefore the network
load must be carefully monitored. If the network load is too high, the program logic
should be reorganized in order to work with the READ_REG function block, a
variation of this function block that does not operate in a continuous mode, but
under command control.
112
Transferring Data Using Communication Blocks
SLAVEREG
Start of the area in the addressed slave from which the source data is read. The
source area always resides within the 4x register area. SLAVEREG expects the
source reference as offset within the 4x area. The leading "4" must be omitted (e.g.
59 (contents of the variables or value of the literal) = 40059).
The parameter can be specified as direct address, located variable, unlocated
variable, or literal.
NO_REG
Number of registers to be read from the addressed slave (1 ... 100). The parameter
can be entered as a Direct address, Located variable, Unlocated variable, or Literal.
REG_READ
This word parameter addresses the first register in a series of NO_REG registers,
listed one after the other, which are used as a destination data area. The parameter
must be entered as a Direct address or located Variable.
STATUS
Error code, see Runtime errors.
The parameter can be specified as direct address, located variable or unlocated
variable.
113
Transferring Data Using Communication Blocks
CWRITE_REG
Function
Description
The purpose of this Function block is to write the register area continuously. It
transfers data from the PLC via TCP/IP Ethernet to an addressed slave.
EN and ENO can be configured as additional parameters.
Note: You must be familiar with the routing procedures of the network when
programming a CWRITE_REG function.
Note: For technical reasons, this function block does not allow the use of ST and
IL programming languages.
Symbol
Block Representation
CWRITE_REG
DINT
INT
WORD
WordArr5
Parameter
Description
114
SLAVEREG
NO_REG
REG_WRIT
AddrFld
STATUS
WORD
Description of Parameters
Parameter
Data Type
Meaning
SLAVEREG
DINT
Offset address of the first 4x register in the slave to be written to
NO_REG
INT
Number of registers to be written to slave
REG_WRIT
WORD
First 4x register of the source data area
AddrFld
WordArr5
Data structure for transferring the TCI/IP address
STATUS
WORD
MSTR error code, see Runtime errors
Transferring Data Using Communication Blocks
Elementary
Description for
WordArr5 with
TCP/IP Ethernet
CWRITE_REG
Block Function
Mode
Elementary description for WordArr5 with TCP/IP Ethernet
Element
Data Type
Meaning
WordArr5[1] WORD
Low value byte: MBP on Ethernet Transporter (MET) mapping
index
High value byte: Slots of the NOE module
WordArr5[2] WORD
Byte 4 (MSB) of the 32-bit destination IP address
WordArr5[3] WORD
Byte 3 of the 32-bit destination IP address
WordArr5[4] WORD
Byte 2 of the 32-bit destination IP address
WordArr5[5] WORD
Byte 1 (LSB) of the 32-bit destination IP address
Although a large number of CWRITE_REG function blocks can be programmed,
only sixteen write operations may be active at the same time. It makes no difference
whether these operations are performed using this function block or others (e.g.
MBP_MSTR, MSTR, WRITE_REG). All function blocks use one data transaction
path and require multiple cycles to complete a job.
If several CWRITE_REG function blocks are used within an application, they must
at least differ in the values of their NO_REG or REG_WRITE parameters.
Note: A TCP/IP communication between a Quantum PLC (NOE 771 xx) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
The entire routing information is contained in data structure WordArr5 of input
AddrFld. The type of function block connected to this input and thus the contents of
the data structure depend on the network used.
Please use:
z TCP/IP Ethernet: the function block TCP_IP_ADDR
Note: For experts: The WordArr5 data structure can also be used with constants.
Note: This function block puts a heavy load on the network. The network load must
therefore be carefully monitored. If the network load is too high, the program logic
should be reorganized to work with the WRITE_REG function block, which is a
variant of this function block that does not operate in continuous mode but is
command driven.
115
Transferring Data Using Communication Blocks
SLAVEREG
Start of the area in the addressed slave to which the source data are written. The
destination area always resides within the 4x register area. SLAVEREG expects the
destination address as offset within the 4x area. The initial "4" must be omitted (e.g.
59 (contents of the variables or value of the literal) = 40059).
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
NO_REG
Number of registers to be written to slave processor (1 ... 100). The parameter can
be specified as direct address, located variable, unlocated variable, or Literal.
STATUS
Error code, see Runtime errors.
The parameter can be specified as direct address, located variable or unlocated
variable.
REG_WRIT
This word parameter addresses the first register in a series of NO_REG Successive
registers used as source data area.
The parameter must be entered as a direct address or located variable.
116
Transferring Data Using Communication Blocks
READ_REG
Function
Description
If requested, this function block will read a register area once (rising edge of the REQ
input). It reads data from an addressed slave via TCP/IP-Ethernet.
EN and ENO can be projected as additional parameters.
Note: You must be familiar with the routing procedures of your network when
programming a READ_REG function.
Note: Note: For technical reasons, this function block does not allow use of the
programming languages ST and IL.
Symbol
Block Representation
READ_REG
BOOL
DINT
INT
WordArr5
Parameter
Description
NDR
REQ
SLAVEREG
ERROR
NO_REG REG_READ
AddrFld
STATUS
BOOL
BOOL
WORD
WORD
Description of Block Parameters
Parameter
Data Type Meaning
REQ
BOOL
Start read operation once
SLAVEREG
DINT
Offset address of the first 4x register in the slave to be read from
NO_REG
INT
Number of registers to be read from slave
AddrFld
WordArr5
Data structure describing the TCP/IP address
NDR
BOOL
Set to "1" for one cycle after reading new data
ERROR
BOOL
Set to "1" for one scan in case of error
STATUS
WORD
Error code, see Runtime errors
REG_READ
WORD
First 4x area register for read values
117
Transferring Data Using Communication Blocks
Elementary
Description for
WordArr5 with
TCP/IP Ethernet
Function Mode of
READ_REG
Blocks
Elementary description for WordArr5 with TCP/IP Ethernet
Element
Data Type
Meaning
WordArr5[1]
WORD
Low value byte: MBP on Ethernet Transporter (MET) mapping
index
High value byte: Slot of the NOE module
WordArr5[2]
WORD
Byte 4 (MSB) of the 32-bit destination IP address
WordArr5[3]
WORD
Byte 3 of the 32-bit destination IP address
WordArr5[4]
WORD
Byte 2 of the 32-bit destination IP address
WordArr5[5]
WORD
Byte 1 (LSB) of the 32-bit destination IP address
Although a large number of READ_REG function blocks can be programmed, only
sixteen read operations may be active at the same time. In such a case it is
insignificant whether they are the result of this function block or of other read
operations (e.g. MBP_MSTR, MSTR, CREAD_REG). All function blocks use one
data transaction path and require multiple cycles to complete a job.
Note: A TCP/IP communication between a Quantum PLC (NOE 771 xx) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
The entire routing information is contained in data structure WordArr5 of input
AddrFld. The type of function block connected to this input and thus the contents of
the data structure depends on the network used.
Please use:
z TCP/IP EtherNet the function block TCP_IP_ADDR
Note: For experts: The WordArr5 data structure can be used with constants as
well.
REQ
118
A rising edge triggers the read transaction.
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
Transferring Data Using Communication Blocks
SLAVEREG
Start of the area in the addressed slave from which the source data is read. The
source area always resides within the 4x register area. SLAVEREG expects the
source reference as offset within the 4x area. The leading "4" must be omitted (e.g.
59 (contents of the variables or value of the literal) = 40059).
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
NO_REG
Number of registers to be read from the addressed slave (1 ... 100).
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
NDR
Transition to ON state for one program cycle signifies receipt of new data ready to
be processed.
The parameter can be specified as direct address, located variable, or unlocated
variable.
ERROR
Transition to ON state for one program cycle signifies detection of a new error.
The parameter can be specified as direct address, located variable, or unlocated
variable.
REG_READ
This word parameter addresses the first register in a series of NO_REG registers
lying in series used as destination data area.
The parameter must be entered as a direct address or located variable.
STATUS
Error code, see Runtime errors.
The parameter can be specified as direct address, located variable or unlocated
variable.
119
Transferring Data Using Communication Blocks
WRITE_REG
Function
Description
If requested, this Function block will write a register area once (rising edge of the
REQ input). It transfers data from the PLC via TCP/IP Ethernet to an addressed
slave.
EN and ENO can be configured as additional parameters.
Note: You must be familiar with the routing procedures of your network when
programming a WRITE_REG function.
Note: For technical reasons, this function block does not allow the use of ST and
IL programming languages.
Symbol
Block Representation
WRITE_REG
BOOL
DINT
INT
WORD
WordArr5
Parameter
Description
120
REQ
SLAVEREG
NO_REG
REG_WRIT
AddrFld
DONE
ERROR
BOOL
BOOL
STATUS
WORD
Description of Parameters
Parameter
Data Type Meaning
REQ
BOOL
Start write operation once
SLAVEREG
DINT
Offset address of the first 4x register in the slave to be written to
NO_REG
INT
Number of registers to be written from slave
AddrFld
WordArr5
Data structure transferring the TCP/IP address
REG_WRIT
WORD
First 4x register of the source data area
DONE
BOOL
Set to "1" for one scan after writing data
ERROR
BOOL
Set to "1" for one scan in case of error
STATUS
WORD
Error code, see Runtime errors
Transferring Data Using Communication Blocks
Elementary
Description for
WordArr5 with
TCP/IP Ethernet
Function Mode of
the WRITE_REG
Module
Elementary description for WordArr5 with TCP/IP Ethernet
Element
Data Type
Meaning
WordArr5[1] WORD
High value byte: Slot of the NOE module
Low value byte: MBP on Ethernet Transporter (MET) mapping
index
WordArr5[2] WORD
Byte 4 (MSB) of the 32-bit destination IP address
WordArr5[3] WORD
Byte 3 of the 32-bit destination IP address
WordArr5[4] WORD
Byte 2 of the 32-bit destination IP address
WordArr5[5] WORD
Byte 1 (LSB) of the 32-bit destination IP address
Although a large number of WRITE_REG function blocks can be programmed, only
sixteen write operations may be active at the same time. In such a case it is
insignificant whether they are the result of this function block or of other write
operations (e.g. MBP_MSTR, MSTR, CWRITE_REG). All function blocks use one
data transaction path and require multiple cycles to complete a job.
If several WRITE_REG function blocks are used within an application, they must at
least differ in the values of their NO_REG or REG_WRITE parameters.
Note: A TCP/IP communication between a Quantum PLC (NOE 771 xx) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
The status signals DONE and ERROR report the function block state to the user
program.
The entire routing information is contained in data structure WordArr5 of input
AddrFld. The type of function block connected to this input and thus the contents of
the data structure depend on the network used.
Please use:
z TCP/IP Ethernet: the function block TCP_IP_ADDR
Note: For experts: The WordArr5 data structure can also be used with constants.
REQ
A rising edge triggers the read transaction.
The parameter can be specified as direct address, located variable or unlocated
variable.
121
Transferring Data Using Communication Blocks
SLAVEREG
Start of the area in the addressed slave from which the source data is read. The
source area always resides within the 4x register area. SLAVEREG expects the
source reference as offset within the 4x area. The leading "4" must be omitted (e.g.
59 (contents of the variables or value of the literal) = 40059).
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
NO_REG
Number of registers to be read from the addressed slave (1 ... 100).
The parameter can be specified as direct address, located variable, unlocated
variable, or Literal.
REG_WRIT
This word parameter addresses the first register in a series of NO_REG registers
used as source data area.
The parameter must be entered as a direct address or located variable.
DONE
Transition to ON state for one program scan signifies data have been transferred.
The parameter can be specified as direct address, located variable or unlocated
variable.
ERROR
Transition to ON state for one program scan signifies detection of a new error.
The parameter can be specified as direct address, located variable or unlocated
variable.
STATUS
Error code, see Runtime errors.
The parameter can be specified as direct address, located variable, or unlocated
variable.
122
Transferring Data Using Communication Blocks
TCP_IP_ADDR
Function
Description
This Function Block enables the input of TCP/IP addresses for the READ_REG,
CREAD_REG, WRITE_REG and CWRITE_REG Function Blocks. The address is
transferred in the form of a data structure.
The parameters EN and ENO can additionally be projected.
Note: You must be familiar with your network when programming the
TCP_IP_ADDR Function Block.
Symbol
Block representation
TCP_IP_ADDR
BYTE
BYTE
Map_Idx
Slot_ID
BYTE
BYTE
BYTE
BYTE
Ip_B4
Ip_B3
Ip_B2
Ip_B1
AddrFld
Parameter
Description
WordArr5
Description of Parameters
Parameter Data Type
Meaning
Map_Idx
BYTE
Map-Index
MBP on Ethernet Transporter (MET) mapping index
Slot_ID
BYTE
Slot ID
Slot of the NOE module
Ip_B4
BYTE
Byte 4 (MSB) of the 32-bit destination IP address
Ip_B3
BYTE
Byte 3 of the 32-bit destination IP address
Ip_B2
BYTE
Byte 2 of the 32-bit destination IP address
Ip_B1
BYTE
Byte 1 (LSB) of the 32-bit destination IP address
AddrFld
WordArr5
Data structure used to transfer the TCP/IP address
123
Transferring Data Using Communication Blocks
Elementary
Description for
WordArr5
Map_Idx
Elementary description for WordArr5
Element
Data Type
Meaning
WordArr5[1]
WORD
High value byte: Slot of the NOE module
Low value byte: MBP on Ethernet Transporter (MET) mapping
index
WordArr5[2]
WORD
Byte 4 (MSB) of the 32-bit destination IP address
WordArr5[3]
WORD
Byte 3 of the 32-bit destination IP address
WordArr5[4]
WORD
Byte 2 of the 32-bit destination IP address
WordArr5[5]
WORD
Byte 1 (LSB) of the 32-bit destination IP address
The MBP on Ethernet Transporter (MET) mapping index is given at the Map_Idx
input, i.e. if MET is 6, the value appears as follows:
0
Slot_ID
0
0
0
1
1
0
If an NOE in the rack of a Quantum controller is addressed as destination node, the
value at the Slot_ID input represents the physical NOE slot, i.e. if the NOE is
plugged in at Slot 7 of the rack, the value appears as follows:
0
AddrFld
0
0
0
0
0
1
1
1
If an NOE in the rack of a Quantum controller is addressed as a destination node,
the value in the High value byte represents the physical slot of the NOE and the Low
value byte represents the MBP on Ethernet Transporter (MET) mapping index, i.e.
if the NOE is inserted in slot 7 of the rack and the MET mapping index is 6, the first
element of the data structure looks as follows:
Low value byte
High value byte
0
0
0
0
0
1
1
1
0
0
0
0
0
1
1
0
High value byte Slots 1 ... 16
Low value byte MBP on Ethernet Transporter (MET) mapping index
124
Transferring Data Using Communication Blocks
MBP_MSTR
Function Block
With this Function block, it is possible to select one of 12 available network
communication operations.
Although a large number of MBP_MSTR function blocks can be programmed, only
sixteen of them can be active at the same time. All function blocks use one data
transaction path and require multiple cycles to complete a job.
Note: A TCP/IP communication between a Quantum PLC (NOE 771 xx) and a
Momentum PLC (all TCP/IP CPUs and all TCP/IP I/O modules) is only possible,
when only one read or write job is carried out in every cycle. If several jobs are sent
per PLC cycle, the communication stops without generating an error message in
the status register of the function block.
Note: In FBD and LD sections, the function block can only be used on the program
level, i.e. not in Derived Function Blocks (DFBs).
Note: For technical reasons, this function block does not allow the use of
programming languages ST and IL.
EN and ENO can be configured as additional parameters.
Note: You must be familiar with the routing procedures of your network when
programming an MSTR function.
Symbol
Block representation
MBP_MSTR
BOOL
BOOL
ENABLE
ABORT
ACTIVE
ERROR
SUCCESS
CONTROL
DATABUF
BOOL
BOOL
BOOL
WORD
WORD
125
Transferring Data Using Communication Blocks
Parameter
Description
Description of parameters
Parameter
Data Type
Meaning
ENABLE
BOOL
Enable MSTR function
ABORT
BOOL
Cancel active MSTR operation
ACTIVE
BOOL
Operation is active
ERROR
BOOL
Faulty operation
SUCCESS
BOOL
Operation completed successfully
CONTROL
WORD
First 4x register of the MSTR control block
DATABUF
WORD
First 4x register of the data field
Function Mode of
MBP_MSTR
Blocks
Using the MBP_MSTR block, one of 12 available network communication
operations can be triggered via the network. Each operation receives a code.
Whether the operations are available depends on the type of network used.
Valid Function
Codes
Valid function codes:
Code
TCP/IP Ethernet
1
Write Data
X
2
Read Data
X
3
Get Local Statistics
X
4
Clear Local Statistics
X
5
Write Global Data
-
6
Read Global Data
-
7
Get Remote Statistics
X
8
Clear Remote Statistics
X
9
Peer Cop Status (Peer Cop Health)
-
10
Reset optional module
X
11
Read CTE (Config extension)
X
12
Write CTE (Config extension)
X
13
Send email
X
Legend:
126
Function
X
Yes
-
No
Transferring Data Using Communication Blocks
ENABLE
When ON, the operation specified in the first CONTROL register is enabled.
ABORT
When ON, the currently active operation is aborted.
ACTIVE
ON, if the operation is active.
ERROR
ON, if the operation was aborted without success.
SUCCESS
ON, if the operation concluded successfully.
DATABUF
The 4x register specified is the first in a group of successive output/marker words,
making up the data field. For operations providing data, e.g. the write operation, the
data field is the data source. For operations receiving data, e.g. the read operation,
the data field is the data sink.
In the case of Ethernet CTE Read and Write operations, the middle input stores the
contents of the Ethernet configuration extension table in a series of registers.
CONTROL
This word parameter addresses the first of several successive 4x registers. The
control block is contained in these registers. The first register displayed contains a
number from 1 to 12, which provides the operation code of the MODBUS operation
to be performed. The contents of the sequence registers are determined by the
operation.
The structure of the control block differs according to the network used:
z TCP/IP Ethernet
Control Block for
TCP/IP Ethernet
Control block for TCP/IP Ethernet
Register
Contents
4x
Indicates one of the Operations which are valid for TCP/IP
4x + 1
Indicates the Error status
4x + 2
Indicates the length (number of registers transferred)
4x + 3
Indicates MSTR operation-dependent information
4x + 4
Routing register
Low value byte: MBP on Ethernet Transporter (MET) mapping index
High value byte: Slot of the NOE module
4x + 5
Byte 4 (MSB) of the 32-bit destination IP address
4x + 6
Byte 3 of the 32-bit destination IP address
4x + 7
Byte 2 of the 32-bit destination IP address
4x + 8
Byte 1 (LSB) of the 32-bit destination IP address
127
Transferring Data Using Communication Blocks
Routing Register
(4x + 4) in TCP/IP
Ethernet
If a NOE in the rack of a Quantum controller is addressed as destination node, the
value in the high value byte represents the physical NOE slot and the value in the
low value byte represents the MBP on Ethernet (MET) mapping index, i.e. if the NOE
is plugged in at Slot 7 of the rack and the MET mapping index is 6, the first element
of the data structure appears as follows:
Low value byte
High value byte
0
0
0
0
0
1
1
1
0
0
0
0
0
1
1
0
High value byte Slots 1 to 16
Low value byte MBP on Ethernet Transporter (MET) mapping index
128
Transferring Data Using Communication Blocks
MSTR Function Error Codes
Overview
The following information describes the error codes for MSTR operations.
Where Displayed
If an error occurs during an MSTR operation, a hexadecimal error code is displayed
in the first implied register in the control block (the top node). Function error codes
are network-specific.
TCP/IP Ethernet
Error Codes
The following table describes the errors that can occur in the MSTR control block if
the MSTR routine runs over TCP/IP Ethernet.
Hex Error Code
Meaning
1001
User has aborted the MSTR element.
2001
An unsupported operation type has been specified in the control block.
2002
One or more control block parameters has been changed while the MSTR
element is active (applies only to operations that take multiple scans to
complete). Control block parameters may be changed only when the MSTR
element is not active.
2003
Invalid value in the length field of the control block.
2004
Invalid value in the offset field of the control block.
2005
Invalid values in the length and offset fields of the control block.
2006
Invalid slave device data area.
2008
Invalid slave device network routing
3000
Generic MODBUS fail code.
30ss*
MODBUS slave exception response.
4001
Inconsistent MODBUS slave response.
F001
Option Module not responding
F002
Module not fully initialized
* ss = subfield
The following table lists the ss subfield values in error code 30ss.
ss Hex value
Meaning
01
Slave device does not support the requested operation.
02
Nonexistent slave device registers requested.
03
Invalid data value requested.
04
Reserved
05
Slave has accepted long-duration program command.
06
Function cannot be performed now; a long-duration command is in effect.
07
Slave rejected long-duration program command.
129
Transferring Data Using Communication Blocks
TCP/IP Ethernet
Network Errors
130
The following table describes the errors that can occur in the MSTR control block as
a result of an error on the TCP/IP Ethernet network.
Hex Error
Code
Meaning
5004
Interrupted system call
5005
I/O error
5006
No such address
5009
The socket descriptor is invalid
500C
Not enough memory
500D
Permission denied
5011
Entry exists
5016
An argument is invalid
5017
An internal table has run out of space
5020
The connection is broken
5028
Destination address required
5029
Protocol wrong type for socket
502A
Protocol not available
502B
Protocol not supported
502C
Socket type not supported
502D
Operation not supported on a socket
502E
Protocol family not supported
502F
Address family not supported
5030
Address already in use
5031
Cannot assign requested address
5032
Socket operation on a non-socket
5033
Network is unreachable
5034
Network dropped connection on reset
5035
Network caused connection abort
5036
Connection reset by peer
5037
No buffer space available
5038
Socket is already connected
5039
Socket is not connected
503A
Cannot send after socket shutdown
503B
Too many references, cannot splice
503C
Connection timed-out
(See note below.)
Transferring Data Using Communication Blocks
503D
Connection refused
503E
Network is down
503F
Text file busy
5040
Too many levels of links
5041
No route to host
5042
Block device required
5043
Host is down
5044
Operation now in progress
5045
Operation already in progress
5046
Operation would block
5047
Function not implemented
5048
Hardware length is invalid
5049
Route specified cannot be found
504A
Collision in select call: these conditions have already been selected by another
task.
504B
Task ID is invalid
5050
No Network Resource
5051
Length Error
5052
Addressing Error
5053
Application Error
5054
Client in Bad State for Request
5055
No Remote Resource (Note: May indicate no path to Remote Device)
(See note below.)
5056
Nonoperational TCP Connection
5057
Incoherent Configuration
Note: Error Codes 503C and 5055
z Error 5055 can occur before a 503C error.
No remote device takes precedence over a timeout.
131
Transferring Data Using Communication Blocks
CTE Error Codes
The following table lists the error codes that are returned if there is a problem with
the Ethernet configuration extension table (CTE) in your program configuration.
Hex Error Code
132
Meaning
7001
There is no Ethernet configuration extension.
7002
The CTE is not available for access.
7003
The offset is invalid.
7004
The offset + length is invalid.
7005
Bad data field in the CTE.
Transferring Data Using Communication Blocks
Read and Write MSTR Operations
Overview
This section describes the MSTR Read and Write operations.
Introduction
An MSTR Write operation (operation type 1 in the displayed register of the top node)
transfers data from a master source device to a specified slave destination device
on the network. An MSTR Read operation (operation type 2 in the displayed register
of the top node) transfers data from a specified slave source device to a master
destination device on the network. Read and Write use one data master transaction
path and may be completed over multiple scans.
Note: TCP/IP Ethernet routing must be accomplished via standard third-party
Ethernet IP router products
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node)
that contain the Read or Write information,
Register
Function
Displayed
Operation Type 1 = Write, 2 = Read
Content
First implied
Error status
Displays a hex value indicating an MSTR error.
Exception response, where
response size is incorrect.
Exception code
+3000
Exception response where
response size is incorrect.
4001
Read Write
Second implied Length
Write = number of registers to be sent to slave. Read =
number of registers to be read from slave.
Third implied
Specifies starting 4x register in the slave to be read from
or written to (1 = 4001, 49 =40049).
Slave device
data area
Fourth implied
Low byte
Quantum backplane slot address of the NOE module.
Fifth ... Eighth
implied
Destination
Each register contains one byte of the 32-bit IP address.
133
Transferring Data Using Communication Blocks
Read/Write MSTR Operation (FC 23)
Overview
This section describes the MSTR Read/Write operation, Function Code (FC) 23.
Introduction
In a single transaction, the MSTR read and write operation transfers data from a
master source device to a specified stave destination device and then transfers data
from this specified slave source to the master.
Note: FC 23 can only be used with these two models:
z NOE 771 01, version 2.0 and higher
z NOE 771 11, version 2.0 and higher
Control Block
Utilization
134
The following table describes the registers in the MSTR control block (the top node),
registers that contain the Read or Write information.
Register
Function
Content
Displayed
Operation Type
23 = Read/Write
1st Implied
Error Status
Displays a hex value indicating a MSTR error
2nd Implied
Write Length
Number of registers to be sent to slave
3rd Implied
Slave device writes
data area
Specifies starting 4x register in the slave to be written
to (1 = 400001, 49 = 40049)
4th Implied
Slot ID
Slot where the NOE is located
5th Implied
IP - 34
Byte 4 (MSB) of the 32 bit destination IP address
6th Implied
IP - 33
Byte 3 of the 32 bit destination IP address
7th Implied
IP - 32
Byte 2 of the 32 bit destination IP address
8th Implied
IP - 31
Byte 1 (LSB) of the 32 bit destination IP address
9th Implied
Read Length
Number of registers to be read from slave
10th Implied
Slave device reads
data area
Specifies starting 4x register in the slave to be read to
Transferring Data Using Communication Blocks
Get Local Statistics MSTR Operation
Overview
This section describes the Get Local Statistics operation.
Introduction
The Get Local Statistics operation (operation type 3 in the display register of the top
node) obtains information related to the local node where the MSTR has been
programmed. (See TCP/IP Ethernet Statistics, p. 146.)
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Get Local Statistics information.
Register
Function
Displayed
Operation Type 3
Content
First implied
Error status
Displays a hex value indicating an MSTR error, if
relevant.
Second implied Length
Starting from offset, the number of words of statistics from
the local processor’s statistics table; the length must be >
0 < data area.
Third implied
Offset
An offset value relative to the first available word in the
local processor’s statistics table. If the offset is specified
as 1, the function obtains statistics starting with the
second word in the table.
Fourth implied
Low byte
Quantum backplane slot address of the NOE module.
Fifth ... Eighth
implied
Not applicable
135
Transferring Data Using Communication Blocks
Clear Local Statistics MSTR Operation
Overview
The following information describes the Local Statistics operation.
Introduction
The Clear Local Statistics operation (operation type 4 in the displayed register of the
top node) clears statistics relative to the local node where the MSTR has been
programmed.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Clear Local Statistics information.
Register
Function
Displayed
Operation Type 4
Content
First implied
Error status
Displays a hex value indicating an MSTR error, if
relevant.
Second implied Not applicable
136
Third implied
Not applicable
Fourth implied
Low byte
Fifth ... Eighth
implied
Not applicable
Quantum backplane slot address of the NOE module.
Transferring Data Using Communication Blocks
Get Remote Statistics MSTR Operation
Overview
The following information describes the Get Remote Statistics operation.
Introduction
The Get Remote Statistics operation (operation type 7 in the displayed register of
the top node) obtains information relative to remote nodes on the network. This
operation may require multiple scans to complete and does not require a master
data transaction path. (See TCP/IP Ethernet Statistics, p. 146.)
The remote Ethernet module always returns its complete statistics table if a request
is made, even if the request is for less than the full table. The MSTR instruction then
copies only the amount of words you have requested to the designated 4x registers.
Note: TCP/IP Ethernet routing must be accomplished via standard third-party
Ethernet IP router products.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Get Remote Statistics information.
Register
Function
Displayed
Operation Type 7
Content
First implied
Error status
Displays a hex value indicating an MSTR error, if
relevant.
Second implied Length
Starting from an offset, the number of words of statistics
from the local processor’s statistics table; the length must
be > 0 < data area.
Third implied
Specifies an offset value relative to the first available
word in the local processor’s statistics table. If the offset
is specified as 1, the function obtains statistics starting
with the second word in the table.
Offset
Fourth implied
High byte
Destination index
Fifth ... Eighth
implied
Destination
Each register contains one byte of the 32-bit IP address.
137
Transferring Data Using Communication Blocks
Clear Remote Statistics MSTR Operation
Overview
The following information describes the Clear Remote Statistics operation.
Introduction
The Clear Remote Statistics operation (operation type 8 in the displayed register of
the top node) clears statistics relative to a remote network node from the data area
in the local node. This operation may require multiple scans to complete and uses a
single data master transaction path.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Clear Remote Statistics information.
Register
Function
Displayed
Operation Type 8
Content
First implied
Error status
Displays a hex value indicating an MSTR error, if relevant.
Second implied Not applicable
138
Third implied
Not applicable
Fourth implied
High byte
Destination index
Fifth ... Eighth
implied
Destination
Each register contains one byte of the 32-bit IP address.
Transferring Data Using Communication Blocks
Peer Cop Health MSTR Operation
Overview
The following information describes the Peer Cop Health operation.
Introduction
The Peer Cop Health operation (operation type 9 in the displayed register of the top
node) reads selected data from the Peer Cop communications health table and
loads that data to specified 4x registers in state RAM. The Peer Cop
communications health table is 12 words long, and the words are indexed via this
MSTR operation as words 0 ... 11.
Note: The Peer Cop Health MSTR block is operational only if a Peer Cop based I/
O Scanner has been configured.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain information for a Peer Cop Health operation.
Register
Function
Content
Displayed
Operation Type 9
First implied
Error status
Displays a hex value indicating an MSTR error, if relevant.
Second implied Data Size
Number of words requested from Peer Cop table
(range 1 ... 12).
Third implied
First word from the table to be read (range 0 ... 11, where
0 = the first word in the Peer Cop table and 11 = the last
word in the table).
Index
Fourth implied
Low byte
Quantum backplane slot address of the NOE module.
Fifth ... Eighth
implied
Destination
Each register contains one byte of the 32-bit IP address.
139
Transferring Data Using Communication Blocks
Peer Cop
Communications
Health Status
Information
The following information describes the structure of the Peer Cop health table:
Each bit in each table word is used to represent an aspect of communications health
relative to a specific node on the TCP/IP network:
z The bits in words 0 ... 3 represent the health of the global input communication
expected from nodes 1... 64. Since global input is not supported these bits are
set to zero.
z The bits in words 4 ... 7 represent the health of the output from a specific node.
z The bits in words 8 ... 11 represent the health of the input to a specific node.
The following table shows the 12 contiguous registers used by the health table and
the words to which they are indexed. Each row that is configured is mapped to a bit
position.
Word 1 Bit Positions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21
22
23
24
25
26
27
28
29
30
31
32
37
38
39
40
41
42
43
44
45
46
47
48
53
54
55
56
57
58
59
60
61
62
63
64
Word 2 Bit Positions
17
18
19
20
Word 3 Bit Positions
33
34
35
36
Word 4 Bit Positions
49
Peer Cop
Communications
Health Bit State
140
50
51
52
The state of a Peer Cop health bit reflects the current communication status of its
associated node. The following list provides more detailed information:
z A health bit is set if data is successfully exchanged with its corresponding node.
z A health bit is cleared if no communication has occurred with the corresponding
node within the configured Peer Cop health time-out period.
z All health bits are cleared at PLC start time. The health bit for a given node is
always zero if its associated Peer Cop entry is null.
z All global health bits are always reported as zero.
Transferring Data Using Communication Blocks
Reset Option Module MSTR Operation
Overview
The following information describes the Reset Option Module operation.
Introduction
The Reset Option Module operation (operation type 10 in the displayed register of
the top node) causes a Quantum NOE option module to enter a reset cycle to reset
its operational environment.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Reset Option Module information.
Register
Function
Displayed
Operation Type 10
Content
First implied
Error status
Displays a hex value indicating an MSTR error, if relevant.
Second implied Not applicable
Third implied
Not applicable
Fourth implied
Low byte
Fifth ... Eighth
implied
Not applicable
Quantum backplane slot address of the NOE module.
141
Transferring Data Using Communication Blocks
Read CTE (Config Extension Table) MSTR Operation
Overview
The following information describes the Read CTE operation.
Introduction
The Read CTE operation (operation type 11 in the displayed register of the top
node) reads a given number of bytes from the Ethernet configuration extension table
to the indicated buffer in PLC memory. The bytes to be read begin at a byte offset
from the beginning of the CTE. The content of the Ethernet CTE table is displayed
in the middle node of the MSTR block.
Control Block
Utilization
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Read CTE information.
Register
Function
Content
Displayed
Operation Type 11
First implied
Error status
Displays a hex value indicating an MSTR error, when
relevant.
Second implied Not applicable
142
Third implied
Not applicable
Fourth implied
Low byte
Fifth ... Eighth
implied
Not applicable
Quantum backplane slot address of the NOE module.
Transferring Data Using Communication Blocks
CTE Display
Implementation
The values in the Ethernet configuration extension table (CTE) are displayed in a
series of registers in the middle node of the MSTR instruction when a Read CTE
operation is implemented. The middle node contains the first of 11 contiguous 4x
registers.
The following table describes the CTE data contained in the registers.
Parameter
Register
Frame type
Displayed
Content
1 = 802.3
2 = Ethernet
IP Address
First implied
Byte 4 (MSB) of the 32-bit IP address
Second implied
Byte 3 of the 32-bit IP address
Third implied
Byte 2 of the 32-bit IP address
Fourth implied
Byte 1 (LSB) of the 32-bit IP address
Subnetwork Fifth implied
mask
Sixth implied
Gateway
Hi word
Low word
Seventh implied Byte 4 (MSB) of the 32-bit gateway address
Eighth implied
Byte 3 of the 32-bit gateway address
Ninth implied
Byte 2 of the 32-bit gateway address
Tenth implied
Byte 1 (LSB) of the 32-bit gateway address
Eleventh implied High byte
Software defined Module
Type (Ignored by M1 and
NOE modules)
0 = NOE211
1 = NOE251
2 = NOE77100
3 = NOE77110
4 = M1
5 = NOE77101
6 = NOE77111
Low byte
IP Address Algorithm
0: Take IP Address from above
definition (default) (All modules
support this functionality)
1: Always take IP Address from
BOOTP Server (M1 and NOE
771 x0 support this functionality)
2: Disable Ethernet functionality
(M1 only)
Note: Module type only used by the p-unit during an upload to determine module.
143
Transferring Data Using Communication Blocks
Write CTE (Config Extension Table) MSTR Operation
Overview
The following information describes the Write CTE operation.
CTE Write
Implementation
The Write CTE operation writes an indicated number of bytes from PLC memory,
starting at a specified byte address, to an indicated Ethernet configuration extension
table at a specified offset. The content of the Ethernet CTE table is contained in the
middle node of the MSTR block.
Network
Implementation
The Write CTE operation (type 12 in the displayed register of the top node) can be
implemented for TCP/IP Ethernet networks via the appropriate network adapter.
Note: Modbus Plus networks do not use this operation.
Control Block
Utilization
In a Write CTE operation, the registers in the MSTR control block (the top node)
differ according to the network in user.
The following table describes the registers in the MSTR control block (the top node).
These registers contain the Write CTE information.
Register
Function
Content
Displayed
Operation Type
12
First implied
Error status
Displays a hex value indicating an MSTR error, if
relevant.
Second implied
Not applicable
Third implied
Fourth implied
Low byte
Either a value displayed in the high byte of the
register or not used.
Slot Index
Number displayed in the low byte, in a range 1 ...
16 indicating the slot in the local backplane where
the option resides.
Fifth ... Eighth implied Not applicable
144
Transferring Data Using Communication Blocks
CTE Display
Implementation
The values in the Ethernet configuration extension table (CTE) are displayed in a
series of registers in the middle node of the MSTR instruction if a Write CTE
operation is implemented. The middle node contains the first of 11 contiguous 4x
registers.
The following table describes the CTE data contained in the registers.
Parameter
Register
Content
Frame type
Displayed
1 = 802.3
2 = Ethernet
IP Address
First implied
First byte of the IP address
Second implied
Second byte of the IP address
Third implied
Third byte of the IP address
Fourth implied
Fourth byte of the IP address
Subnetwork
mask
Fifth implied
Hi word
Sixth implied
Low word
Gateway
Seventh implied
First byte of the gateway
Eighth implied
Second byte of the gateway
Ninth implied
Third byte of the gateway
Tenth implied
Fourth byte of the gateway
Eleventh implied High byte
Software defined
Module Type (Ignored
by M1 and NOE
modules)
0 = NOE211
1 = NOE251
2 = NOE771 00
3 = NOE771 10
4 = M1
5 = 140 NOE 771 01
6 = 140 NOE 771 11
Low byte
IP Address Algorithm
0: Take IP Address from above
definition (default) (All modules
support this functionality)
1: Always take IP Address from
BOOTP Server (M1 and NOE
771 x0 support this functionality)
2: Disable Ethernet functionality
(M1 only)
145
Transferring Data Using Communication Blocks
TCP/IP Ethernet Statistics
Overview
The following information describes the available TCP/IP Ethernet Statistics.
Introduction
A TCP/IP Ethernet board responds to the "Get Local Statistics" and "Set Local
Statistics" commands with the following information.
146
Word
Meaning
00 ... 02
MAC address
03
Board Status (see the Board Status Bit Definition table in this map)
04 and 05
Number of receiver interrupts
06 and 07
Number of transmitter interrupts
08 and 09
Transmit _ timeout error count
10 and 11
Collision_detect error count
12 and 13
Missed packets
14 and 15
Memory error
16 and 17
Number of times driver has restarted
18 and 19
Receive framing error
20 and 21
Receiver overflow error
22 and 23
Receive CRC error
24 and 25
Receive buffer error
26 and 27
Transmit buffer error
28 and 29
Transmit silo underflow
30 and 31
Late collision
32 and 33
Lost carrier
34 and 35
Number of retries
36 and 37
IP address
Transferring Data Using Communication Blocks
Board Status
Word Bit
Definition
Board Status
Word Bit
Definition by
Module Type
The following table describes the word bit definitions for Board Status.
Bit #
Definition
15 ... 12
Module Type (See Module type table below)
11
(Reserved)
10
0 = half duplex 1 = full duplex
9
0 = not configured 1 = configured
8
0 = PLC not running 1 = PLC/NOE running
7
0 = Link LED off 1 = Link LED on
6
0 = Appl LED off 1 = Appl LED on
5
0 = twisted pair 1 = fiber
4
0 = 10 Mbit 1 = 100 Mbit
3 ... 0
(Reserved)
The following table describes the values of the Module Types.
Value of Bits 15 ... 12
Module Type
0
NOE 2x1
1
ENT
2
M1E
3
NOE 771 00
4
ETY
5
CIP
6
(Reserved)
7
(Reserved)
8
(Reserved)
9
(Reserved)
10
NOE 771 10
11
NOE 771 01
12
NOE 771 11
13 ... 15
(Reserved)
For bit level detail for the Momentum 170ENT1101 and Momentum 170ENT11000
see the Momentum Ethernet Communication Adapter 170ENT11001 and
170ENT11000 User Guide, 870USE11400.
For bit level detail for the 140NOE211xx see the TCP/IP Module User Guide,
840USE10700.
147
Transferring Data Using Communication Blocks
148
Global Data
(Publish / Subscribe) Utility
5
At a Glance
Introduction
The material in this section presents the Global Data (Publish / Subscribe) utility
available on the following modules.
z 140 NOE 771 01
z 140 NOE 771 11
z HE CPU 651 x0
For more information on the publish-subscribe model, go to this URL:
http://www.isa.org/journals/intech/feature/printable/
1,1171,596,00.html
What's in this
Chapter?
This chapter contains the following topics:
Topic
Page
Planning the Global Data (Publish / Subscribe) System
150
Multicast Filtering
154
Quantum NOE Global Data Configuration
155
Configuration of Global Data (Publish / Subscribe) by the Web for NOE 771 x1
157
Configuring the Global Data (Publish / Subscribe) Utility
161
149
Global Data (Publish/ Subscribe)
Planning the Global Data (Publish / Subscribe) System
Overview
Global Data service is a real time Publisher/Subscriber mechanism providing the
most efficient data exchange for PLC application coordination.
Devices supporting Global Data are arranged in a distribution group for the purpose
of application variable exchange and synchronization. Each Global Data device can
publish up to one network (application) variable and subscribe up to 64 network
(application) variables.
The Quantum NOE’s embedded Global Data Configuration Web page provides a
configuration screen to determine which and how many application variables are
exchanged with this service. After configuration, the exchanges between all stations
belonging to the same distribution group are done automatically.
The Global Data service uses %MW (4x registers) for Global Data exchanges.
Key Features of
Global Data
The main features for Global Data are:
z One publisher and many subscribers
z A device can publish one network variable of up to 512 %MW words (4x registers)
z A device can subscribe of up to 64 network variables of up to 2048 %MW words
(4x registers)
z A device subscribes to the complete network variable
z One distribution group per network IP address
z Application defined publication rate
z Up to 64 Global Data Network variables (numbered from 1 to 64) can be part of
the data distribution group
z A NOE has only one multicast address; consequently, it can only publish and
subscribe inside the group
z A device can participate in several distribution groups by using multiple NOEs in
the rack
Global Data has an advantage over Client / Server services when more than one
subscriber is receiving the same data since only one transaction is necessary for all
subscribers to receive the data.
This advantage offers two benefits:
z Reduce overall network traffic
z Ensure tighter synchronization of multiple subscribers
150
Global Data (Publish/ Subscribe)
The Global Data (Publish / Subscribe) utility is a powerful function incorporated into
the NOE product line. Implementing Global Data requires a configuration that spans
many PLCs throughout the system. Therefore, we recommend preplanning your
installation before implementation. Work spent on preplanning saves time and
money by reducing errors and unnecessary debugging time. Preplanning also
serves as an aid to ensuring consistency throughout the system.
Go to paper before computer.
We offer the following table to help with your system planning. The table below is a
graphic representation of a recommended configuration table for system planning,
which we call the Global Data Planning Spreadsheet. You may create your own
table using the format below or you may download a Microsoft ExcelTM spreadsheet
template which is available on the Schneider public Web site.
Here is the graphic representation of the Global Data Planning Spreadsheet.
Planning Your
System
Configuration
Parameter
Checking
Variable ID
Symbol 1.
Length
Device Number
(Registers)
Variable
Public.
Status
1
2
1
VALVE_STATUS
20
PUB
SUB
...
NONE
3
OK
2
VALVE_CONTROL
10
SUB
NONE
PUB
OK
PUMP_CONTROL
50
OK
...
64
SUB
PUB
NONE
Device Publication Status:
OK
OK
OK
Total Publication Size per Node:
20
50
10
Total Subscription Size per Node:
60
20
0
Group IP Address
239.255.255.0
Multicast Filtering Enabled
OFF
Default 4x Address for Health 400100
Distribution Period
10
Health Timeout
1000
Data Zone
400200
1. Entries or changes to the symbol (description) do NOT affect or change a variable or the system. The Symbol
used in the Quantum product line has no relation to the Concept / Unity product line symbol.
151
Global Data (Publish/ Subscribe)
Table of Global Data Limits
Parameter
Limit
Maximum number of publish variables
per device
1
Maximum size for the publish variable
512 Registers = 512 Words (16 bits) = 1024 Bytes
Maximum number of subscription
variables per device
64 (63 if this device is publishing)
Maximum size for the subscripe
variables per device
2048 registers = 2048 Words (16 bits) = 4096 Bytes
Note: We recommend that you consider the following when planning.
z 10 to 20% Increase margin for growth
We suggest that you allow for a percentage increase in growth of any variable,
a 10 to 20% increase allowance should be sufficient.
z Add at end
We recommend that you add variables at the end of the configuration because
variables added at the end of the configuration do not affect the existing
application address. Therefore, you avoid changing the existing addresses in
your configuration, which can be a time consuming process.
152
Global Data (Publish/ Subscribe)
Table of Global Data Planning Spreadsheet
Parameter
Description
Parameter Checking
Reserved
Variable Id
Represents the Data ID on the NOE’s Global Data
Configuration Web page
Symbol
Symbolic name for Global Data exchange.
Length Words
(Registers)
Length of Global Data information. Number of %MW words (4x
registers).
Device Number
Number of devices for the Global Data network. Of up to 64.
Variable Public. Status
Automatic information of the correct publication status of the
Global Data network. Only by using the Microsoft ExcelTM
spreadsheet. Information per symbol.
Device Publication
Status
Automatic information of the correct publication status of the
Global Data network. Only by using the Microsoft ExcelTM
spreadsheet. Information per device.
Total Publication Size per Publication size for the specific node. The maximum publication
Node
size is 512 words (registers) per node
Total Subscription Size
per Node
Subscription size for the specific node. The maximum
subscription size is 2048 words (registers) per node
Group IP Address
Enabled
IP address for multicast networking. Identifies the stations
distribution group. The address range is from 224.0.0.0 to
239.255.255.255
Multicast Filtering
Enabled
A check box for Ethernet switches that support multicast filtering.
Default Address for
%MW (4x register) address for the Health bits. This is the memory
Health%MW (4x register) area where the Health bits are stored. It has the size of 4 words
(registers).
Distribution Period
Is the minimum number of controller scan times before an update
will occur.
Health Timeout
Is the maximum time between received subscriptions before a
subscription is declared unhealthy (faulty). The value is measured
in milliseconds and can be set to a value that ranges from 50
through 10000 ms (increase in units of 50 ms)
Data Zone
The starting address for the data. This are the registers where the
data information are stored.
153
Global Data (Publish/ Subscribe)
Multicast Filtering
Overview
Your NOE may offer the multicast filtering functionality.
The global data service synchronizes several stations located in a distribution group.
A distribution group is a set of stations identified by using the same IP multicast
address for all stations in the group. By using the same IP address for multiple
devices, multicast exchanges can be used to distribute global data. Several
independent distribution groups can coexist on the same sub-network. Each
distribution group posses its own unique IP multicast address.
Early versions of Switches treat multicast packets as a broadcast. Therefore,
transmitting broadcasts to all nodes, and thereby suppressing all benefits of both
switching and multicasting. Newer version of switches provide automatic Multicast
Filtering, and consequently only forward multicast traffic to the ports that are
connected to registered end-stations.
Multicast Filtering uses the GARP Multicast Registration Protocol (GMRP) to inform
a switch which IP Multicast Addresses are of interest to the attached device
GMRP is defined in the IEEE 802.1D-1998 Standard, which is available as a free
download at: http://IEEE802.org.
In order to use Multicast Filtering, you need to:
1. Ensure that your Switch supports IEEE 802.1D - 1998
2. Click the Multicast filtering check box on the Global Data Configuration area
on the Web page.
Reducing Traffic
Multicast Filtering helps to reduce the traffic on a network, because broadcasts are
sent only to interested, or subscribed, devices.
For distributed applications and one to many communications multicast affords
advantages over unicast:
z Utilizes the network bandwidth more efficiently
z Sends a single transmission instead of multiple transmissions.
z Reduces collisions
z Optimizes the performance of Ethernet module processing
Using Multicast
Filtering
These ConneXium switches support multicast filtering. Other switches from
alternate vendors also support multicast filtering.
154
Switch
Description
499NES17100
Managed Switch with 7 ports 10/100BASE-TX
499NOS17100
Managed Switch with 5 ports 10/100BASE-TX and 2 ports 100BASE-FX
Global Data (Publish/ Subscribe)
Quantum NOE Global Data Configuration
Introduction
Global data configuration is carried out in the network configuration as well as the
data editor.
The variables for the Publish/Subscribe procedure are configured in the data editor.
The screen shot shows the network configuration Global data configuration settings.
ETHERNET_1
Model Family
Modul Address
Rack
TCP/IP 10/100 Regular connection
Module
Module IP Address
IP-Adresse
0 . 0 . 0 . 0
IP Configuration
Subnetwork Mask
0 . 0 . 0 . 0
Access Control I/O Scanning
Gateway Address
0 . 0 . 0 . 0
Global Data
Module Utilities
Access Control
YES
YES
I/O Scanning
YES
Global Data
YES
SNMP
YES
Address Server
SNMP Address Server Bandwidth
Global data configuration
HealthTimeout
Diistribution period
1000
ms
10
scan
Group address 239 . 10 . 10 . 10
Group name plantgrp
Health bit block (%I / %WIW) %IW1
Multicast Filtering
Parameter description
Parameter
Description
Health timeout
After this time period has run out, the data received becomes invalid.
Group address
Class D Multicast IP address. All nodes in the global data procedure use
the same Multicast address for distributing or receiving data. The address
range is: 224.0.0.0 to 239.255.255.255.
Distribution
time
Time after which the data is received or sent. Minimum scan time of the
PLC.
Group name
Logical name. Defines the varibale allocation to different communication
configurations in the variablen editor.
Status bit block
Address for retrieving the status information of the global data procedure.
Multicast
filtering
Activates an Ethernet switch on connection that supports Multicast
filtering.
155
Global Data (Publish/ Subscribe)
The screen shot shows an image of the data editor.
Variables
Filter
DDT Types
Name
Function Blocks
EDT
*
Name
VALVE_STATUS
VALVE_CONTROL
PUMP_STATUS
DFB Types
Type
ARRAY[0..19] OF Word
ARRAY[0..9] OF Word
ARRAY[0..99] OF Word
Address
%MW200
%MW220
%MW230
DDT
Global ...
PUB
SUB
SUB
Group
plantgrp
plantgrp
plantgrp
IODDT
Enet ID
1
2
3
Parameter description
156
Parameter
Description
Name
Variables ID
Type
Variable type
Address
Variable address
Enet
Type of Global Data Variable. Options: No/Publish/Subscribe
Group
Group name for allocating the variables of the existing network description.
When creating the different Ethernet networks, a logical connection is arranged
here between the network and the variable declaration.
Enet ID
Ethernet ID. Representation of the administrative order.
Global Data (Publish/ Subscribe)
Configuration of Global Data (Publish / Subscribe) by the Web for NOE 771 x1
Modeling the
System
Configuration
There are two methods of configuring a system.
z Configure Each Device Separately
Using this method you configure devices via the Global Data Configuration
Web page for each device. Repeat for each device in the system. We suggest
that you do not use this method because entry errors may occur due to the fact
that the same information must be reentered on each and every device, possibly
as much as 64 times.
z Copy Configuration
You configure all variable IDs, symbols (descriptions), and lengths on one NOE,
then upload to your PC, and download the same configuration to all devices, and
finish with a small customization to each node.
Note: We recommend that you use the Copy Configuration method to configure
all variable IDs, symbols (description), and lengths.
Choosing this method reduces entry errors, allows for verifying the configuration,
and permits you to determine if the system is satisfactory for your needs before
implementing the configuration system wide.
By using this method you enter the variable ID, symbol (description), and length
only once thus ensuring consistency.
When your planning is complete, follow the Configuring Your NOE steps below. We
present these steps both as a picture and as instructions.
157
Global Data (Publish/ Subscribe)
These are the Configuring Your NOE steps displayed as a picture
Enter
Global Data
configuration
into
NOE #1
Upload
Global Data
configuration
to PC
Stop
controller
158
Download
to each NOE
in system
Customize
each NOE’s
Global Data
configuration
Start
controller
Verify
system
Global Data (Publish/ Subscribe)
These are the Configuring Your NOE steps written as instructions.
Step
Action
1
Select one NOE.
2
Using your browser, navigate to that NOE’s Global Data Configuration page.
Follow these links:| Diagnostics and Online Configuration | Configure NOE |
Configure Global Data | Global Data Configuration |
3
Enter the configuration’s variable IDs, symbols (description), and lengths.
4
Click the Update Global Data Configuration button to update the file. This
creates the file glbdata.ini.
Full path follows:
ftp://NOE_IP_ADDRESS/wwwroot/conf/glbdata/glbdata.ini
Note: You substitute NOE_IP_ADDRESS with an address like 192.168.000.010.
Please check the address with your system administrator.
5
Using the FTP process, upload the glbdata.ini file to a PC.
See the section below, Uploading a glbdata.ini file.
6
Stop each controller before you do the customization.
7
Using the same path, download the glbdata.ini file to the other devices.
See the section below, Downloading a glbdata.ini file.
8
Connect your Web browser to each device to customize start address and the
Publish / Subscribe setting.
Note: The Global Data Configuration page is populated with data which comes
from the glbdata.ini configuration file.
Uploading a
glbdat.ini File
The following procedure describes the steps to upload the glbdata.ini file.
Step
Action
1
At the DOS prompt type FTP followed by the IP address and press Enter.
2
At the User prompt type FTP Username and press Enter.
3
At the password prompt enter your FTP Password and press Enter.
4
At the FTP prompt type cd wwwroot/conf/glbdata and press Enter.
5
At the FTP prompt type get and press Enter.
6
At the local file prompt type glbdata.ini and press Enter.
7
At the remote file prompt type glbdata.ini and press Enter.
159
Global Data (Publish/ Subscribe)
Downloading a
glbdat.ini File
Verifying System
Operation
160
The following procedure describes the steps to download the glbdata.ini file.
Step
Action
1
At the DOS prompt type FTP followed by the IP address and press Enter.
2
At the User prompt type the FTP username and press Enter.
3
At the password prompt enter your FTP Password and press Enter.
4
At the FTP prompt type cd wwwroot/conf/glbdata and press Enter.
5
At the FTP prompt type put and press Enter.
6
At the local file prompt type glbdata.ini and press Enter.
7
At the remote file prompt type glbdata.ini and press Enter.
To ensure that the system is operational, do the following:
Step
Action
1
Verify all controllers are running.
2
Look at the health of all variables using the Global Data Diagnostic page.
Follow these links:| Diagnostics and Online Configuration | NOE Diagnostics
| Global Data
Global Data (Publish/ Subscribe)
Configuring the Global Data (Publish / Subscribe) Utility
Overview
Whether you use the Configure Each Device Separately or the Copy Configuration
method, the procedure to configure individual parameters is the same. Therefore, in
order to use the Global Data (Publish / Subscribe) utility in the NOE, you need to
configure the Global Data parameters including:
z
z
z
z
z
Distribution period
Multicast filtering
Health bit location
Global Data base address
Group IP address
The following sections describe in detail the exact steps to configure each parameter
via the Global Data Configuration page.
Accessing the
Global Data
Utility
You access the Global Data utility through the Global Data Configuration page.
Step
1
Action
On your screen click the Diagnostics and Online Configurations link.
Schneider Automation Web Server
Diagnostics and Online Configurations
French
German
Italian
Spanish
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
2
When you click the Diagnostics and Online Configurations link, you are
requested to enter user name and password.
3
Enter your user name and password. The Configure NOE page appears.
4
Click the Configure NOE link.
The Configure NOE page appears.
161
Global Data (Publish/ Subscribe)
Step
5
Action
Click the Configure Global Data link.
Configure NOE
Configure SNMP
Configure Address Server
Configure Global Data
Configure NTP
Configure Email
Home
NOE Proper-
NOE Diagnos- Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
6
The Global Data Configuration page appears.
Global Data Configuration
Gro 23 . 20 . 25 . 25
Health
100
m
Multicast
Distribu- 5
Healt %M 4
to 7
sca
Data %M 0
Update Global Data Configu-
Variable Table
Dat
1
2
3
4
5
6
7
8
9
Type
Symbol
SU
var_01
PU
var_02
SU
var_03
NO
NO
NO
NO
NO
NO
Address
%M 48
%M 60
%M 44
%M
%M
%M
%M
%M
%M
In this screen you may make changes to the configuration.
162
Lenght
2
2
2
to 5
Global Data (Publish/ Subscribe)
Configuring
Global Data
After you have completed the Modelling System Configuration process using the
second method, Copy Configuration, then you modify the following parameters:
z Distribution period
z Health Time Out
z Health Bits location
z Start address
z Type: Pub / Sub / None
Please do NOT change Symbol (description), and Length.
To change the Global Data variables of the group box on the Global Data
Configuration page, follow the instructions below.
Step
Action
1
Adjust the Distribution Period Cycle. Enter a value from 1 through 50.
Note: Distribution period is the minimum number of controller scan times
before an update will occur.
2
Before entering a value in the Group address field, identify the station’s
distribution group. The Group address entry will be an IP address from
224.0.0.0 through 239.255.255.255.
Group address: the Class D Multicast IP address used for a distribution group.
All members of this distribution group are configured to use the same group
address, and therefore, all members can communicate with each other using
Global Data.
3
Set the timeout in the Health Time Out field. This value is measured in
milliseconds and can be set to a value that ranges from 50 through 10,000 ms
(increase in units of 50ms).
Note: Validity Time is the maximum time between received subscriptions
before a subscription is declared unhealthy (faulty).
4
In the Data Zone %MW field set the Data Zone variable.
5
If you are connected to an Ethernet switch that supports multicast filtering, click
the Multicast filtering check box.
6
Enter 4x Register Location for the Health Bits. This is the register where the
health bit will be stored
Note: Health bits run in different directions.
z I/O scanner health bits run left to right.
z Global Data health bits run right to left.
163
Global Data (Publish/ Subscribe)
Changing Global
Data Variables
To change the Global Data variables that appear in the Variable Table area, follow
the instructions below.
Step
Verifying System
Operation
164
Action
1
Highlight the identification number in the Data ID column.
2
In the Type column select the publish / subscribe variable type from the drop
down list.
Three options are available publish, subscribe, or none. These options display
on the screen as follows:
z NONE
z SUB
z PUB
3
In the Symbol column you may enter text to describe the variable.
4
In the Address column you see the application address for this variable.
Note: This is a read only field.
5
In the Length column for each row, type a value, which represents the number
of %MW words. The ending %MW word field is automatically updated. If you are
using the second method, Copy Configuration, you update Length the first
time only.
6
When you are finished, click the Update Global Data Configuration button.
To ensure that the system is operational, do the following:
Step
Action
1
Verify all controllers are running.
2
Look at the health of all variables using the Global Data Diagnostics page.
Follow these links:| Diagnostics and Online Configuration | NOE Diagnostics
| Global Data
I/O Scanner
6
At a Glance
Introduction
This chapter discusses the Ethernet modules’ I/O scanner capabilities.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Page
I/O Scanner Concepts
166
Modicon Quantum with Unity I/O Scanner Configuration
169
165
Transferring Data with the I/O Scanner
I/O Scanner Concepts
Overview
The following information describes how to configure the I/O scanner.
Introduction
The I/O Scanner is a feature that resides in an Ethernet (NOE 771 00, -01, -11, and
CPU 651 x0 modules). The I/O Scanner allows, through a controller, repeated
reading from and/or writing to scanned devices.
Configure the I/O Scanner with Schneider Electric’s programming package Unity
Pro. Use the I/O scanner to transfer data between network devices.
I/O Scan List
The I/O scan list is a configuration table that identifies the targets with which
repetitive communication is authorized. While the controller is running, the Ethernet
module transfers data to and from the controller’s registers as indicated by the I/O
scan list.
Health Block Bits
Each bit corresponds to an entry in the I/O Scanner table. (See Modicon Quantum
with Unity I/O Scanner Configuration, p. 169) Each entry in the table represents one
logical device.
The bits contain the health status for the Modicon Quantum I/O Scanner.
166
Transferring Data with the I/O Scanner
I/O Scanner
Parameters
Functionality of the I/O Scanner.
Parameter
Value
Max. No. of Devices
64: 140 NOE 771 00 (Version 2.2 or earlier)
128: 140 NOE 771 00 (Version 3.0 or later), 140
NOE 771 01, and 140 NOE 771 11 only
128: HE CPU 651 x0
Max. No. of Input Words
4000
Max. No. of Output Words
4000
Health Timeout Value
User configured (1 ms to 2 s in 1 ms increments)
Last Value (Input)
User configured (Zero or Hold)
IP Address
User configured
IP address of scanned device (Slave IP)
Local and Remote Register Reference User configured
Repetition Rate
User configured
Unit ID
User configured
Configure ID only if using a bridge
Operation through a bridge
Modbus bridge: Supported
Modbus Plus bridge: Supported
To configure the I/O Scanner, refer to the section Modicon Quantum with Unity I/O
Scanner Configuration, p. 169.
Using the I/O
Scanner across a
Router
Note: I/O Scanner in the 771 x1 and HE CPU 651 x0
The I/O scanner can scan devices through an IP router with a TTL of 10.
167
Transferring Data with the I/O Scanner
Device Control
Block
Important information about using the Device Control Block:
1
Registers
The Device Control Block consists of registers either eight
(8) words or four (4) double words. Contents of the registers
are mapped in the controller’s memory. Each bit
corresponds to an entry in the table.
2
Disabling Devices
Each I/O Scanner device can be disabled. To disable
individual devices:
1. Select the Device Control Block option.
(Insert a check mark in the box.)
2. Set the associated bit = 1.
(For example, %MD2:4)
3
Mapping Device Control
Block Bits to I/O Scanner
Entry Numbers (#)
See the table for mapping entry numbers to bits.
Each entry number represents a logical device on the
network.
4
Setting Bits
If Device Control Block bit is set to
z 0 = Device is enabled
z 1 = Device is disabled
Note: Concept Users
Use diagnostic words instead of "Device Control Block."
Mapping Device
Control Block
Bits to I/O
Scanner Entry
Numbers (#)
Register
Register
Word 1
Table Entry # 1
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Word 2
Table Entry # 17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Bit
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Bit
15
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Word 3 through Word 7
Word 8
168
Table Entry # 11
3
11
4
11
5
11
6
11
7
11
8
11
9
12
0
12
1
12
2
12
3
12
4
12
5
12
6
12
7
12
8
Bit
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
15
Double
Word
Transferring Data with the I/O Scanner
Modicon Quantum with Unity I/O Scanner Configuration
Introduction
Use the I/O scanner to transfer data between master devices and slave devices.
Note: Important Information: Enable/Disable Device Control Block
If you enable the Device Control Block, you must have
1. Unity Pro V2.0 or higher
2. NOE 771 01 and NOE 771 11: version 3.5 or higher
3. 140 CPU 651x0: version 2.0 or higher
Enabling the Device Control Block with outdated versions of the firmware, causes
the I/O scanner to NOT work.
I/O Scanner
Configuration
Dialog
The I/O scanner tab displays the I/O Scanner configuration dialog. Use for
configuring a NOE 771 00, -01, or -11. Note: the dialog for the CPU 651 x0 does
NOT have a Health Block field.
IP Configuration
Access Con- I/O Scan-
Global Data SNMP
Address
Bandwidth
I/O Scanner configuration
Health Block : (%I / %IW) %IW0
Slave IP
Address
1
2
3
4
5
6
7
8
9
139.124.10.8
139.124.10.8
139.124.10.8
139.124.10.8
139.124.10.8
139.124.10.8
Unit ID
Object
(ms)
255
255
255
255
255
255
Device Control Block : (%MDx:4) %MD2:4
RD
Health Repetitive
Timeout rate (ms) Master
1500
1500
1500
1500
1500
1500
208
208
208
208
208
208
%MW200
%MW202
%MW204
%MW206
%MW208
%MW210
RD
Slave
Index
0
2
4
6
8
10
RD
length
2
2
2
2
2
2
Last value
(input)
Hold Last
Set to 0
Set to 0
Hold Last
Hold Last
Set to 0
WR
Maste
Object
%MW100
%MW102
%MW104
%MW106
%MW108
%MW110
WR
Slave
Index
0
2
4
6
8
10
Set to 0
169
Transferring Data with the I/O Scanner
I/O Scanner
Configuration
Parameters
Set configuration parameters in the I/O Scanner configuration dialog. Enter data in
appropriate fields.
Parameter/Field
Description
Health Block:
(%I/%IW)
Length of the table: 8 words (%IW) or 128 bits (%I).
Each bit represents the status of the corresponding slaves.
Note: Health Block field is available only on NOE 771 00, -01, and 11. Health Block field is NOT available on CPU 651 x0.
Device Control
Block Check Box
If the option is selected (check mark appears in box),
z enabled
User allows master to send requests to slave.
If the option is NOT selected (check mark does NOT appear in box),
z disabled
No requests sent from master to slave.
Device Control
Block: (%MDx:4)
Note: If the Device Control Block parameter is disabled (check mark
does NOT appear), the I/O Scanner closes the connection and sets
the Health Bit to an unhealthy state (Health Bit set = 1).
Entry #
Entries available: 1 -128
Each entry represents a logical device on the network.
Slave IP Address
IP address of the scanned Ethernet device
Unit ID
Specific ID of the device on the Modbus/Modbus Plus network
The device connects to the Ethernet through a bridge.
Health Timeout (ms) Timeout period specified in milliseconds
Health Block
170
Repetitive rate (ms)
Rate at which the data will be scanned
RD Master Object
Destination address in the controller for reads
RD Slave Index
Source address of the input/output module for the read period
RD length
Number of words to read
Last value (Input)
Status of the inputs in the event of an error
WR Master Object
Source address of the controller for writes
The write is carried out in words.
WR Slave Object
Destination address of the slave for writes
WR length
Number of words to write
Description
Information
Coordination of the bits to the different data types
Bit
Data Type
%I
%IW
1
%I1
%IW1.0
16
%I16
%IW1.15
17
%I17
%IW2.0
Address Server Configuration /
Faulty Device Replacement
7
At a Glance
Introduction
This section covers the Address Server Configuration / Faulty Device Replacement
service available only on the NOE 771 -01 and -11, Transparent Factory / Real Time
modules. The Faulty Device Replacement service offers you a method of handling
device replacement without disrupting the system nor interrupting service.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Page
Address Server Configuration / Faulty Device Replacement
172
Understanding Faulty Device Replacement
175
Configuring Faulty Device Replacement
178
171
Address Server Configuration / Faulty Device Replacement
Address Server Configuration / Faulty Device Replacement
Overview
The Address Server provides 2 capabilities:
1. Standard BOOTP Server Behavior
Enter the MAC Address and IP Configuration. The NOE BOOTP server will
provide the IP configuration when the device sends a BOOTP request.
2. Faulty Device Replacement (FDR) Behavior
Enter the Role Name or the MAC Address of the device. The device will send its
Role Name or the MAC Address with its DHCP request. With the DHCP response
from the NOE, the device will receive its IP Configuration, plus the name and
location of a configuration file.
The next step for a FDR-compliant device is to download its configuration from
the NOE.
Consult your Schneider Electric Sales Representative for the current list of FDRCompliant devices.
The Address Server in the NOE supports both modes at the same time. You select
a mode by entering either the MAC Address or the Role Name in the Address
Server Node Configuration page. You may enter only one or the other, but not
both.
The Faulty Device Replacement capability allows automatic configuration of FDRcompliant devices.
Identifying a Role
Name
Inherent in the discussion of Faulty Device Replacement is the idea of a Role Name.
A Role Name is a logical name that the user assigns to a device, a logical name that
has a meaning within the application.
Some examples of a Role Name might be:
z ENT_6 (6th Momentum ENT in your application)
z OUTPUT_VALVE_2 (2nd Output Valve in your application)
Role Names are case sensitive.
172
Address Server Configuration / Faulty Device Replacement
Faulty Device
Replacement
The Faulty Device Replacement service offers a method of handling device
replacement without disrupting the system nor interrupting service. Should a device
fail, replacing that device is easy. When the new device is physically connected to
the network, the system (including the new device) is able to
z Provide the replacement device with the IP address of the previous device
z Ensure that new device is working in the same manner as the previous device
z Restore the I/O device application parameters in order to restart the device with
the same configuration as before the failure
Faulty Device Replacement enables you to avoid configuring a new device when a
faulty device is replaced: You enter the device name in the new device, and the task
is completed. You have a new configuration scheme for I/O and smart devices,
which allows:
z Creating an automatic network configuration
z Managing automatic application parameters
Faulty Device Replacement is implemented using the combination of DHCP and
FTP/TFTP standard protocols. The device implements a DHCP client and an FTP
or TFTP client. Choosing between FTP and TFTP has no direct impact on your
system. The choice depends only on device memory footprint: TFTP is much
smaller than FTP.
Faulty Device Replacement offers the following functionality
z FDR Manager
z FDR Agent
Faulty Device Replacement management is based on three entities:
z Agent device embedding the DHCP client and FTP/TFTP client
z DHCP server
z FTP/TFTP server
Role Name
The logical Role Name should be written on devices. The technician can get the
new device from stores, enter the corresponding Role Name into the device, and
place the device in the system. The device automatically gets its configuration and
starts running with no further input from the technician. This process is designed to
get your machine up and running quickly. All the technician has to do for any FDR
compliant device is to enter the Role Name into the new device.
173
Address Server Configuration / Faulty Device Replacement
Address Server
Limits
This table displays the parameters and limits of the Address Server.
Parameter
Limit
Maximum number of Address Server entries
128
Maximum size of the configuration file per device
4K bytes
Total size of Faulty Device Replacement storage
512K bytes
Maximum Role Name size
16 Characters
Note: For the DHCP Server to work correctly the following must be observed:
z Address class and subnet class configured for the devices has to match
z Address class of the NOE and of the devices has to be the same
Operating on a
Corporate
Network
Note: Operating on a corporate network
z Before placing the NOE on a corporate network, Schneider Electric recommends
that you discuss the installation with your MIS department. It is likely that your
company's corporate network has at least one DHCP Server running already. If
the NOE's DHCP server is running on the same network, it may disturb the
network.
z To avoid any possible problem related to the NOE's DHCP server on the
corporate network, you have to ensure that the DHCP server is not running in the
NOE by not having address entries in the configuration. If there are no configured
devices in the Address Server Configuration page, then the NOE will not start the
DHCP server.
Available FDR
Agents
Three FDR agents are available
z Momentum ENT
z Micro ETZ
z ATV58*
*Available 2002
The role-name.prm configuration files are stored in the NOE in non-volatile
memory. Therefore, after a power failure all configurations will be available.
BOOTP and
DHCP
Compatible
Devices
Use either the MAC Address or the Role Name to assign IP addresses. Therefore,
you may use the DHCP server with devices that support BOOTP only, such as
Momentum ENT v1.
174
Address Server Configuration / Faulty Device Replacement
Understanding Faulty Device Replacement
Understanding
Confirmation
and Error
Messages
In addition to highlighting errors the system provides confirming information and
error messages.
Confirmation Message If you successfully added, modified, or removed and entry,
the following alert message appears.
Error Messages Error messages, appearing as an icon in the seventh column,
display on the Address Server Configuration page, or they appear as dialog box.
Error Icon If an entry is not loaded in the DHCP server or loaded with a different
configuration, an icon of an exclamation point displays in the seventh column.
The icon informs you of the difference between the current and stored
information.
z Not Loaded in Server: A red icon displays.
z Duplicate Configuration: A blue icon displays.
Place the pointer over the icon and a pop-up window appears and displays a
message
z Not Loaded in Server:
z Present Configuration:
175
Address Server Configuration / Faulty Device Replacement
Error Dialog Box If you entered an existing role name or MAC address, you will
receive an alert message asking you to correct the entry.
176
Address Server Configuration / Faulty Device Replacement
Modifying the
Database
If you need to add or modify an entry in the database, use the Address Server Node
Configuration page. Three fields must be filled in Device IP address, Subnet
Mask, and Gateway.
Choose either the Role Name or Device MAC address field. When one field is
selected, the other is made unavailable.
Adding Entries If you are adding a device, the page appears with values. You
need to enter either a Role Name or a MAC Address.
If you are adding an entry, submit your selection using the Add the Entry button.
Modifying Entries If you are modifying an entry, the Device IP address, Subnet
Mask, and Gateway fields display with the current configuration.
If you are modifying an entry, submit your selection using the Reset the Form
button.
Each field of the Address Server Node Configuration page has restrictions, which
are detailed below.
z Role Name
Each role name must be unique. Only letters, numerals, and underscores are
allowed. No more than 16 characters are allowed, and no spaces are allowed.
z Device MAC Address
This address must be in hexadecimaL format and six (6) bytes long (6x2
characters). The MAC address can be entered with or without a delimiting
character between each pair of lower or upper case hexadecimal characters. The
delimiting characters improve readability. There are three choices for a delimiting
character:
z Space " "
Use the spacebar to create the space.
z Colon ":"
z Hyphen "-"
z Device IP address
The IP address must use the standard numeric Internet Protocol address that
uniquely identifies each computer on the network. The IP address is a 32-bit
identifier made up of four groups of numbers (from 0 through 255), each number
separated by a period, for example 123.456.78.9.
z Subnet Mask
The subnet mask must be entered in IP address format.
z Gateway
The gateway must be entered in IP address format. The gateway must be on the
same subnet as the device.
177
Address Server Configuration / Faulty Device Replacement
Configuring Faulty Device Replacement
Configuring the
Address Server
To configure the Address Server you use Web pages generated by the embedded
Web server. The first page that appears is the Address Server Configuration
page. The first column contains buttons used for selecting devices. The Address
Server Configuration page displays configuration information for each device in
the system and has seven columns in the table.
Displayed on this page is information about:
z Role Name
z Mac Address
z IP Address
z Subnet Mask
z Gateway
A additional, unnamed column indicates if there is a difference between the current
and the stored configuration. If a difference exists, an exclamation point is displayed.
This is the Address Server Configuration page. All devices are compatible.
Address Server Configuration
Role Name
IP Address
Subnet Mask
Gateway
myNIP
MAC Address
192.168.3.11
255.255.255.0
192.168.3.11
ENT_1st_floor
192.168.5.14
255.255.0.0
192.168.2.1
Refresh Address Server Database Table
Add a New Entry
Hom
Configure
Change an Entry
NOE Prop-
Delete an Entry
NOE Diag- Sup-
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
On the Address Server Configuration page you can:
z Add a New Entry
z Change an Entry
z Delete an Entry
178
Address Server Configuration / Faulty Device Replacement
Choosing
Options
The Address Server Configuration page allows you to choose different options for
adding or altering the configurations of your NOE. The options available to you are:
z Selecting an entry
z Adding an entry
z Changing an entry
z Deleting an entry
Below we describe the method and options chosen to perform any of the four
options listed above. Screen shots are presented to accompany the Adding an entry
section.
Selecting an Entry When the page displays, by default no entries are selected.
Use the radio buttons in the first column to select an entry. Only one entry may
be selected at a time.
Adding an Entry When the Add a New Entry button is selected, the Address
Server Node Configuration page appears. This page displays information
about a device.
If you selected a device, this page displays the device’s configuration.
Configuration information displays in four of the five fields of the dialog box. Only
the Role information field is blank. You should enter a Role name, for example
ENT_7.
If no device is selected, default values appear in all the fields.
Changing an Entry Before using this button, you must select an entry in the
database by choosing one of the radio buttons in the first column. If you fail to
choose an entry, an error message appears.
179
Address Server Configuration / Faulty Device Replacement
When the Change an Entry button is selected, the Address Server Node
Configuration page appears. The information displayed is for the device
selected.
Deleting an Entry Before using this button, you must select an entry in the
database by choosing one of the radio buttons in the first column. If you fail to
choose an entry, an error message appears.
The entry selected will be removed from the database. Before completely
deleting an entry, a warning message appears. Click Yes if you want to delete the
entry, no if you don’t.
180
Address Server Configuration / Faulty Device Replacement
If you click Yes, a dialog box appears.
Click OK. Another dialog box appears notifying you that the deletion was successful.
Highlighting
Errors
If there are problems with the configuration parameter information entered, the
system indicates problems using a highlighting mechanism. All the configurations
appear in purple and italic, and the device with configuration problems appears in
red and bold.
The system detects the following errors:
z Bad Role Name
The valid Role Name characters are:
z a through z (lower case)
z A through Z (upper case)
z "_" (underscore)
z Bad MAC Address
The valid MAC Address characters are:
z 0 through 9
z A through F
z Wrong IP Address
z Wrong Subnet Mask
z Wrong Gateway
z Double Entry
Each entry must have a unique Role Name or MAC Address. If a duplicate Role
Name or MAC Address is entered, the system highlights the error.
Erroneous errors are not loaded into the DHCP server. Therefore, errors must be
corrected before loading. There are two ways of correcting the error.
Correcting through Web page Make the changes on the Web page and submit
the change.
Correcting through the Address Server configuration file Make the changes in
the file and reboot the server.
181
Address Server Configuration / Faulty Device Replacement
182
Network Management Service
(SNMP)
8
At a Glance
Introduction
The following material describes the Simple Network Management Protocol (SNMP)
and the Schneider private MIB. Under the Schneider private MIB is the Transparent
Factory Ethernet private MIB.
What's in this
Chapter?
This chapter contains the following topics:
Topic
SNMP
Page
184
ASN.1 Naming Scheme
187
Configuring a NOE with SNMP
189
Configuring a NOE with TFE Private MIB
191
183
SNMP
SNMP
Overview
This following information describes the Simple Network Management Protocol
(SNMP), which is configured on your NOE or 140 CPU 651 x0.
Introduction
Network management software allows a network manager to
z Monitor and control network components
z Isolate problems and find their causes
z Query devices such as a host computer, routers, switches, and bridges to
determine their status
z Obtain statistics about the networks to which they attach
Manager/Agent
Paradigm
Network management software follows the conventional client-server model.
To avoid confusion with other network communication protocols that use the client/
server terminology, network management software uses the following terms:
z Manager
For the client application that runs on the manager’s computer
z Agent
For the application that runs on a network device
The manager uses conventional transport protocols (e.g., TCP or UDP) to establish
communication with the agent. Managers and agents then exchange requests and
responses according to the network management protocol.
Simple Network
Management
Protocol
Your NOE module is configured with the Simple Network Management Protocol
(SNMP), which is the standard protocol used to manage a local area network (LAN).
SNMP defines exactly how a manager communicates with an agent.
The SNMP defines the format of the requests that a manager sends to an agent and
the format of the replies that the agent returns to the manager.
The MIB
Each object SNMP has access to has to be defined and given a unique name. Both
the manager and agent program must agree on the names and the meanings of the
fetch and store operations. The set of all objects SNMP can access is known as a
Management Information Base (MIB).
The Private MIB
Schneider obtained a private MIB, Groupe_Schneider (3833). Under the Groupe
Schneider private MIB is a Transparent Factory Ethernet (TFE) private MIB. The
Transparent Factory SNMP embedded component controls the Schneider private
MIB function.
184
SNMP
Choosing a
SNMP Manager
If you have a SNMP Manager already working, you may continue to use that SNMP
Manager. If you are selecting a SNMP Manager, there are many SNMP Managers
on the market, and you may use any of these managers. You must use a SNMP
Version 1 compliant manager.
If you do not currently use a SNMP Manager in your organization and are evaluating
SNMP Managers for purchase, then we recommend that you consider the HiVision‚
with the ConnexView Add-On developed for use with Schneider Automation PLCs.
Please contact your Schneider Electric sales office for availability and pricing of
HiVision‚ and ConnexView‚.
Using a SNMP
Manager
The process for obtaining a SNMP Manager
Step
Action
1
Get Schneider .mib file from the NOE Web page.
You are going to find the .mib file as a packed file under /wwwroot/
SchneiderTFE.zip on your NOE module.
2
Compile .mib file in the compiler that comes with the NOE.
3
Load compiled .mib file to the SNMP manager.
4
When you are done, you will see the Schneider private MIB manager in your
manager.
The process is simple.
Get
file
Compile
file
Load
file
into
your manager
185
SNMP
More SNMP
Information
186
SNMP and related subjects are well documented on Web sites and in many books
z As of this writing, a useful description appears on Microsoft’s Technet pages.
Browse to http://www.microsoft.com/technet. Use the Search function to find
"Network Management for Microsoft Networks Using SNMP."
z Use an Internet search engine to search for a SNMP introduction, a SNMP
tutorial, and other topics on SNMP.
z The SNMP FAQ from the news group comp.protocols.snmp appear on many
.com and .org Web pages. Search for the combination of
"comp.protocols.snmp" and "FAQ."
z A list of print books about SNMP appears in the SNMP FAQs. In addition, a
search of most online retail book sites will yield a substantial list of titles.
SNMP
ASN.1 Naming Scheme
ASN.1 Overview
Abstract Syntax Notation One (ASN.1) is a formal language for abstractly describing
messages to be exchanged between distributed computer systems.
187
SNMP
An Example
Objects in a MIB are defined with the ASN.1 naming scheme that assigns each
object a long prefix that guarantees that the name will be unique. For example, an
integer that counts the number of IP datagrams that a device has received is named:
iso.org.dod.internet.mgmt.mib.ip.ipinReceives.
The following figure depicts the ASN.1 Naming Scheme example.
iso (1)
org (3)
dod (6)
internet (1)
directory (1)
mgmt (2)
system
(1)
experimental (3)
mib (2)
interfaces
(2)
ip (4)
address
translation
(3)
ipForwarding (1)
ipDefaultTTL (2)
ipinReceives (3)
This object name is represented in an SNMP message by assigning each part an
integer. So, the above message would appear as 1.3.6.1.2.2.4.3.
Each integer has the following meaning.
z 1 = ISO (International Organization for Standardization)
z 3 = identified organization — one of branches under the ISO root
z 6 = U. S. Department of Defense (DOD) — one of the children under branch1.3
z 1 = the Internet subtree under 1.3.6
z 2 = the mgm branch — (one of seven) of the Internet subtree. It is managed by
the Internet Assigned Numbers Authority, and includes the standard MIBs
z 2 = mib-2(1) group of managed objects
z 4 = ip — the mib-2(1) IP group (one of 11)
z 3 = ipinReceives — the MIB object
188
SNMP
Configuring a NOE with SNMP
The Object
Identifier (OID)
In the ASN.1 Naming Scheme example, the MIB object identified by the notation
1.3.6.1.2.2.4.3 is referred to as the Object Identifier or OID. All OIDs can be
envisioned as part of a tree structure which begins at the root (ISO) and branches
out with each subtree identified by an integer.
SNMP Protocol
Data Units
SNMP uses Protocol Data Units (PDUs) to carry the requests and responses,
between the manager and the agents, for the information contained in an OID.
As the following figure shows, the SNMP message is the innermost part of a typical
network transmission frame.
Local
IP
Network
Header
Header
Version
UDP
Header
Community
SNMP
Message
Local
Network
Trailer
GetRequest, SetRequest,
or Trap PDU
The PDUs within the SNMP initiate the communication between the manager and
the agents.
The SNMP installed on your NOE module uses the following three PDUs.
z GetRequest
z SetRequest
z Trap
GetRequest PDU
The GetRequest (shortened to Get) PDU is used by the SNMP manager to retrieve
the value of one or more objects (OIDs) from an agent.
SetRequest PDU
The SetRequest (shortened to Set) PDU is used by the SNMP manager to assign a
value to one or more objects (OIDs) residing in an agent.
Trap PDU
The Trap PDU is used by the agent to alert the manager that a predefined event has
occurred.
189
SNMP
Version &
Community
Identifiers
The version identifies the version number of the SNMP software being used by the
manager and the agent. Your NOE supports Version 1 of the SNMP. The community
is an identifier that you assign to your SNMP network. If community names for the
manager and the agent do not agree, the agent will send an authentication failure
trap message to the manager. If the community names and version number agree,
the SNMP PDU will be processed.
What Can Be
Configured
Your NOE module can be configured to send an authentication trap to two SNMP
managers if it receives a community name in a Get/Set request that does not match
the configured name. Also, you can configure the SysContact and SysLocation via
the configuration page in the module’s Embedded Web pages. After making
changes in the SNMP Configuration Web page and to set those changes, reboot the
module using hot swap.
190
SNMP
Configuring a NOE with TFE Private MIB
Introduction
A MIB, a Management Information Base, is an element used in network
management. Network management services are based on the need to monitor and
to manage:
z Performance
z Fault occurrences
z Security
Each MIB contains a finite number of objects. Manage your MIB with a management
station running an SNMP management application. The management application
uses GETs and SETs to retrieve system information and to set system environment
variables.
Schneider
Private MIB
Schneider Electric obtained a Private Enterprise Number (PEN) from the Internet
Assigned Numbers Authority (IANA). That number represents a subtree in the
SNMP MIB, a number that is a unique identifier used for Groupe Schneider.
The object identifier for the root of the Groupe Schneider subtree is
1.3.6.1.4.1.3833 and represents a path to the subtree as follows:
iso(1)
org(3)
dod(6)
internet(1)
private(4)
enterprise(1)
GroupeSchneider(3833)
Transparent_Factory_Ethernet(1)
Under the GroupeSchneider private MIB is a Transparent Factory Ethernet (TFE)
private MIB, Transparent_Factory_Ethernet(1).
TFE Private MIB
The Transparent Factory SNMP-embedded component controls the Schneider
private MIB function. The Schneider private MIB, and associated services, perform
Network Management on all components of the system. The Transparent Factory
private MIB provides the data to manage the main Transparent Factory
communication services for all the communication components of the Transparent
Factory architecture (ETYs, NOEs, third party toolkit, ENTs, M1Es). The
Transparent Factory private MIB does not define the specific management
applications and policies.
191
SNMP
The diagram following illustrates the Schneider Electric (Groupe_Schneider (3833)
private enterprise MIB subtree.
Groupe_Schneider (3833)
Transparent_Factory_Ethernet (1)
Switch (1)
Port502_Messaging (2)
I/O_Scanning (3)
Global_Data (4)
Web (5)
Address_Server (6)
Equipment_Profiles (7)
Premium (1)
Quantum (2)
Generic_Device (3)
M1E (4)
ENT (5)
timeManagement (8)
NTP (1)
email (9)
SMTP (1)
The Groupe_Schneider (3833) subtree is the root of Groupe Schneider's private
MIB in the Structure of Management Information (SMI) used by SNMP and defined
in RFC-1155, which is a specification that defines the structure and identification of
management information for TCP/IP-based networks.
192
SNMP
Transparent
Factory Ethernet
Subtree
The Transparent_Factory_Ethernet (1) subtree defines groups that support the
Transparent Factory Ethernet services and devices.
Service
Description
Switch(1)
Subtree defines a brand of switches labeled: ConneXium
switches private MIB
Port502_Messaging(2)
Subtree defines objects for managing explicit client / server
communications supporting applications, such as HMI, SCADA,
or programming tools
I/O_Scanning(3)
Subtree defines objects for managing I/O device communications
that use the I/O Scanner mechanism with the MB/TCP protocol
Global_Data(4)
Subtree defines objects for managing the application coordination
service using a publish / subscribe protocol
Web(5)
Subtree defines objects for managing the activity of the
embedded Web servers
Address_Server(6)
Subtree defines objects for managing the activity of the BOOTP
and (or) DHCP servers
Equipment_Profiles(7)
Subtree defines objects for each type of device in Transparent
Factory Ethernet's product portfolio
timeManagement(8)
Subtree defines objects for managing the UTC time stamp service
email(9)
Subtree defines objects for managing the mail service
Device subtrees, or groups, will be defined for the following devices:
z Premium(1)
z Quantum(2)
z Generic_Device(3)
z M1E(4)
z ENT(5)
As devices are added to Schneider's catalog, Schneider's private MIB will be
extended in the following manner:
z If needed, a Transparent Factory, communication-service object will be added for
the new device in the corresponding Equipment_Profiles(7) subtree. As many
objects as needed can be added to this subtree.
z If needed, a new branch will be added at the same level as
Transparent_Factory_Ethernet(1). This subtree will be created for productspecific objects (such as the ATV58 object under the IndustrialControlProducts (3) subtree).
When a new device is created, a corresponding object description is created in the
ASN.1 format. The ASN.1 file(s) are then given to producers of SNMP manager
software for inclusion in their products.
193
SNMP
Port502
Messaging
Subtree
The Port502_Messaging (2) subtree, or group, provides connection management
and data flow services. The following list describes the function of each object.
Service
Description
port502Status(1)
Indicates the status of the service (Idle, Operational)
port502SupportedProtocol(2)
Indicates the supported protocols (MODBUS, Xway)
port502IpSecurity(3):
Indicates the status of the Port502 IP Security service
(enabled/disabled)
port502MaxConn(4)
Indicates the maximum TCP connection number
supported by the Port502 entity
port502LocalConn(5)
Indicates the TCP connection number currently opened
by the local Port502 entity
port502RemConn(6)
Indicates the TCP connection number currently opened
by the remote entity to the local Port502 entity
port502IpSecurityTable(7)
Indicates a table containing the number of unsuccessful
TCP connection open tries from a remote TCP entity
port502ConnTable(8)
Indicates a table containing Port502 TCP specific
information (MsgIn, MsgOut)
port502MsgIn(9)
Indicates the total number of Port502 messages received
from the network
port502MsgOut(10)
Indicates the total number of Port502 messages sent from
the network
port502MsgOutErr(11)
Indicates the total number of error messages built by the
Port502 messaging entity and sent to the network
port502AddStackStat(12)
Indicates the support of additional port502 stack statistics
1 - Disabled
2 - Enabled
port502AddStackStatTable(13) Indicates additional stack statistics for Port502 (optional)
194
SNMP
I/O Scanning
Subtree
The I/O_Scanning (3) subtree, or group, contains the objects related to I/O Scanning
device management and associated MODBUS communications on Port502.
Service
Description
ioScanStatus(1)
Indicates the global status of the I/O Scanning service
1 - Idle
2 - Operational
3 - Stopped
ioScanMaxDevice(2)
Indicates the maximum number of devices supported by the I/O
Scanning entity
ioScanPolledDevice(3) Indicates the number of devices currently polled by the I/O
Scanning entity
ioScanTransSend(4)
Indicates the total number of transactions sent by the I/O
Scanning entity
ioScanGlbHealth(5)
Indicates the global status of health for the I/O Scanning service
2 - OK: Every remote I/O device is responding
4- Warning: At least one remote I/O device is not responding
ioScanDeviceTable(6)
Displays a table containing information on each remote devices
polled by the I/O Scanning entity
195
SNMP
Global Data
Subtree
The Global_Data (4) subtree, or group, contains the objects related to the Global
Data service.
Service
Description
glbDataStatus(1)
Indicates the global status of the Global Data service
1 - Idle
2 - Operational
3 - Stopped
glbDataMaxPub(2)
Indicates the maximum number of published variables
configured by the Global Data entity
glbDataMaxSub(3)
Indicates the maximum number of subscribed variables
configured by the Global Data entity
glbDataPub(4)
Indicates the total number of publications sent to the network
glbDataSub(5)
Indicates the total number of subscriptions received from the
network
glbDataPubErr(6)
Indicates the total number of publication errors detected by the
local entity
glbDataSubErr(7)
Indicates the total number of subscription errors detected by the
local entity
glbDataGlbSubHealth(8) Indicates the global status of health for the Global Data
subscribed variables
2 - OK: The health status of all subscribed variables are OK
4 - Warning: At least one subscribed variable has a health fault
196
glbDataPubTable(9)
Displays a table containing information on each published
variable (the number of publications, the source IP address, the
number of errors)
glbDataSubTable(10)
Displays a table containing information on each subscribed
variable (the number of subscriptions, the source IP address, the
number of errors, Health)
SNMP
Web Subtree
The Web (5) subtree, or group, contains the objects related to the Web server
service.
Service
Description
webStatus(1)
Indicates the global status of the Web service
1 - Idle
2 - Operational
webPassword (2)
Indicates a switch to enable or disable the use of Web
passwords
1 - Disabled
2 - Enabled
webSuccessfullAccess (3) Indicates the total number of successful accesses to the Web
site
webFailedAttempts (4)
Address Server
Subtree
Equipment
Profile Subtree
Indicates the total number of unsuccessful accesses to the
Web site
The Address_Server (6) subtree, or group, contains the objects related to the
Address Server service. The Address Server can be either a BOOTP server or a
DHCP server.
Service
Description
addressServerStatus(1)
Indicates the global status of the address server service
1 - Idle
2 - Operational
The Equipment_Profiles (7) subtree contains a set of common objects.
Service
Description
profileProductName(1)
Displays the commercial name of the communication
product in a string form (for example: 140 NOE 771 11)
profileVersion(2)
Displays the software version of the communication
product in a string form (for example: Vx.y or V1.1)
profileCommunicationServices(3) Displays a list of the communication services
supported by the profile (Port502Messaging, I/O
scanning Messaging, Global Data, Web, and Address
Server)
profileGlobalStatus(4)
Indicates the global status of the communication
module
1 - NOK
2 - OK
197
SNMP
198
Service
Description
profileConfigMode(5)
Indicates the IP configuration mode of the
communication module
1 - Local: The IP configuration is created locally
2 - dhcpServed: The IP configuration is created by a
remote DHCP server
profileRoleName(6)
Indicates the role name for the IP address
management if it exists (Empty string if there is none)
profileBandwidthMgt(7)
Indicates the status of Bandwidth Management
1 - Disabled
2 - Enabled
profileBandwidthDistTable(8)
Indicates the CPU time distribution between Global
Data, Port502 Messaging, I/O Scanning
profileLedDisplayTable(9)
Displays a table giving the name and the state of each
module’s LEDs
profileSlot(10)
Indicates the position of the communication module
inside the rack if there is one. If there is no rack, the
profileSlot value will be zero
profileCPUType(11)
Indicates that if the CPU type exists, this variable
identifies the host for which that communication
module is a part. If there is no host, the string is empty
profileTrapTableEntriesMax(12)
Indicates the maximum numbers of entries in the Trap
Table. This entry equals the number of possible
remote managers
profileTrapTable(13)
Displays a table allowing you to enable or disable the
private traps for each of the communication services
profileSpecificId(14)
Indicates a unique Profile Specific Identification inside
the equipmentProfile object of the Schneider
Transparent Factory MIB. (For example the PLC
Premium family is 100)
profileIpAddress(15)
Indicates the IP address of the SNMP agent
profileIpNetMask(16)
Indicates the subnet mask associated with the IP
address of the SNMP agent. The value of the mask is
an IP address with all the network bits set to 1 and all
the host bits set to 0
profileIpGateway(17)
Indicates the default Gateway IP address of the SNMP
agent
profileMacAddress(18)
Indicates the Ethernet media-dependent address of
the SNMP agent
SNMP
NTP Subtree
The NTP (1) subtree contains a set of common objects.
Service
Description
ntpStatus(1)
Status of NTP service (not server)
1. 1 = Idle
no configuration
2. 2 = Operational
ntpSrvAddr(2)
IP address of NTP server in dot notation format
ntpLnkSrvStatus(3)
Status of link between module and NTP server
1. 1 = NOK
module can not reach NTP server
2. 2 = OK
ntpReqCnt(4)
Number of requests sent to NTP server
ntpRespCnt(5)
Number of responses received from NTP server
ntpErrCnt(6)
Total number of communication errors
ntpDate(7)
Date of the day
ntpTime(8)
Time of the day
ntpTimeZone(9)
Current time zone
ntpDSTStatus(10)
Daylight Saving Time status
1. 1 = ON
Daylight Saving Time
2. 2 = OFF
Standard Time
ntpLastErr(11)
Last error code generated by system
199
SNMP
SMTP Subtree
The SMTP (1) subtree contains a set of common objects.
Service
Description
smtpStatus(1)
Status of SMTP service (not server)
1. 1 = Idle
no configuration
2. 2 = Operational
smtpSrvAddr(2)
IP address of SMTP server in dot notation format
smtpLnkSrvStatus(3)
Status of link with SMTP server
1. 1 = NOK
link is down; module failed to contact SMTP server
2. 2 = OK
smtpEmailSentCnt(4)
Total number of email messages sent to network
smtpSrvRspCnt(5)
Total number of responses from SMTP server
smtpErrCnt(6)
Total umber of email messages that could not be sent because of
an error
smtpLastErr(7)
Error code of the last error that occurred while trying to send an
email message to the network
smtpLastHdrUsed(8)
Mail header used in the last email message sent successfully on
the network
1. None(0)
no email messages sent
2. Mail header 1(1)
3. Mail header 2(2)
4. Mail header 3(3)
smtpLastMailCnt(9)
Number of seconds elapsed since the last successful email
message sent
smtpSrvChkFallCnt(10) Number of times that the link to SMTP server detected as ‘down’
200
SNMP
Private Traps
and MIB Files
Traps are used to signal status changes to the manager. Using traps helps to avoid
adding traffic.
The status changes signaled by the trap are for the:
z LEDs
z Communication Ports
z I/O Scanning Health Values
z Global Data Health
z NTP service
z SMTP service
The following list describes the characteristics of private traps, which means that
they can:
z Send messages to the two managers whose IP addresses are configured in the
SNMP configuration (either the PL7 or the Web page)
z Use the community name given to this configuration
z Enable or disable each of the Transparent Factory Ethernet Private MIB groups:
Switch (1), Port502_Messaging (2), I/O_Scanning (3), Global_Data (4), Web (5),
Address_Server (6), Equipment_Profiles (7), NTP (8), and SMTP (9)
Private traps are described in the MIB ASN.1 description, which is contained in a
.mib text file.
NTP Traps
1. DST Change Trap
Trap notifies the manager that the NTP server time has changed either from (a)
standard time to daylight saving time or (b) daylight saving time to standard time
2. NTP Status Change Trap
Trap sent when the NTP component status changes (ntpStatus(1))
3. Leap Second Trap
Trap sent when leap seconds are inserted
SMTP Traps
1. SMTP Status Change Trap
Trap is sent when SMTPStatus changes
2. SMTP Link to Server Status Change
Trap is sent when tSMTPLnkSrvStatus changes. Trap is sent when service tries
to send an email. Every 30 minutes a periodic test checks the connection to the
SMTP server.
201
SNMP
202
Time Synchronization Service
9
At a Glance
Introduction
This chapter describes the time synchronization service, which provides an accurate
local clock by using Network Time Protocol (NTP).
What's in this
Chapter?
This chapter contains the following topics:
Topic
Page
Introducing the Time Synchronization Service
204
Using the Time Synchronization Service
207
Using the R_NTPC Block for Time Synchronization
208
203
Using the Time Service
Introducing the Time Synchronization Service
General
The time service synchronizes computer clocks over the Internet. For example, the
time of one client is synchronized either with another server or to a referenced time
source like a radio or satellite receiver.
Typical time service configurations utilize redundant servers and diverse network
paths to achieve high accuracy and reliability. Time service accuracy can be within
a millisecond on LANs and up to a few tens of milliseconds on WANs.
Use the time service for
z event recording—sequence events
z event synchronization—trigger simultaneous events
z alarm and I/O synchronization—time stamp alarms
Features of the
Time Service
z Periodic time correction obtained from the reference-standard time server
z Automatic switch over to a backup time server if a problem occurs with the normal
time server system
z Controller projects use a function block to read the accurate clock, a feature that
allows project events or variables to be time stamped
z Estimated time stamping accuracy of
z 5 mSec for 140 CPU 651 x0’s and higher
z 10 mSec for other CPUs
z Local time zone is configurable and customizable including daylight savings time
z Web page diagnostics for the time synchronization service
204
Using the Time Service
Time
Synchronization
and Time Stamps
The Schneider Electric Ethernet interface modules, NOEs, provide the source timesynchronization signal sent to a controller. The Ethernet module’s firmware includes
an NTP client, which provides time synchronization.
Action
Result
NTP Client requests a time synchronization
signal from an NTP server.
Request is sent over an Ethernet network.
NTP Server responds with a signal.
NTP Client stores the time.
NTP Client sends a message to the
controller’s clock system counter.
The controller updates its internal clock with
the following granularity:
z 1 ms
To read the clock from the PLC application,
z Use the R_NTPC function block in either MAST, FAST, or Interrupt sections.
On an Ethernet network, all controllers should be synchronized with the same NTP
server.
CPS
CPU
NOE
Clock
System
Counter
NTP Request
NTP
Client
R_NTPC
EN0
EN
NTP
Server
Ethernet
Network
NTP Response
Modicon Quantum System
OUT1
OUT2
STATUS
205
Using the Time Service
Time
Synchronization
Definitions
206
Terms related to the time synchronization service
Term
Description of Service
Local clock offset
Accurate local time is maintained by adjusting the time by using a
local clock offset. The local clock offset is calculated by the following
formula.
( (T4 - T1) + (T3 - T2) ) / 2
z T1 = Time when NTP request is transmitted from the module
z T2 = Time when NTP Server receives the request (provided by
the module in response)
z T3 = Time when the NTP Server transmits the response
(provided to the module in the response)
z T4 = Time when NTP Response is received by the module
Time accuracy
Local Time error is < 10 ms compared to the reference NTP server.
Typical: under 5 ms
Worst case: <10 ms
Note:
1. Settling Time:
The maximum accuracy is obtained after 2 updates from the
NTP server.
2. Polling Period Dependency:
The accuracy is dependent upon the polling period. Less than 10
mSec of error is guaranteed for polling periods of 120 seconds
or less. To obtain the best possible accuracy and if your network
bandwidth will allow, reduce the polling period to a small value.
3. For example, choosing a polling time of 5 seconds provides
better accuracy than a time of 30 seconds.
Time zone
Default format: Universal Time, Coordinated (UTC)
Optional: Configure the service to use a local time zone. For
example, GMT+1 for Barcelona or Paris
Daylight saving time
Automatic: module adjusts time in spring and fall
Leap Second
Automatic: module inserts or deletes a second
Note:
1. To compensate for the deceleration of the earth’s rotation, a leap
second is inserted in the UTC time every 18 months by an
INTERNATIONAL EARTH ROTATION SERVICE (IERS).
2. Leap seconds will be inserted automatically as needed. If
needed, leap seconds are inserted at the end of the last minute
in June or December, as commanded by the NTP server.
z
z
Using the Time Service
Using the Time Synchronization Service
Introduction
This material describes special operating conditions related to
z powering up
z Stop or Run PLC
z downloading applications
z configuring the time service
Power Up
On Power-up, to establish accurate system Ethernet network time, the system
z requires the Ethernet module to boot
z uses the Ethernet module to obtain the time from the NTP server
z requires a predefined interval until time is accurate; user’s configuration
determines how long before time is accurate
z may require several updates to achieve peak accuracy
Once an accurate time is received, the service sets the STATUS in the associated
time service register.
The time-service clock value starts at 0 until fully updated from the module.
Stop or Run PLC
Model
Starting Date
Modicon Quantum with Unity
January 1st 1980 00:00:00.00
z Stop and Run have no effect on the accuracy of the clock.
z Stop and Run have no effect on the update of the clock.
z A transition from one mode to the other has no effect on the accuracy of the
system Ethernet network time.
Download
Application
After a download application or an NTP server swap occurs, the status clock value
associated with the time service register in the CPU is reinitialized.
There will be two polling periods before the time is accurate.
NTP
Configuration
(See Configuring the Time Synchronization Service, p. 244)
207
Using the Time Service
Using the R_NTPC Block for Time Synchronization
R_NTPC
Representation
The block reads the Ethernet network system time and transfers the time into
specified parameters: The additional parameter EN should be configured.
R_NTPC block has a 16-bit status word.
R_NTPC
Parameter
Description
Description of parameters
Parameter
Data Type
Description
Display_NTPC
(OUT1)
DT + INT
NTP clock value displayed in
z Year, month, day, hours, minutes, and seconds using the
DT format
z Milliseconds as an INT
Calc_NTPC
(OUT2)
UDINT+INT NTP clock value displayed in
z Seconds as an UDINT
z Fractions of a second as an INT
STATUS
Low Byte
INT
STATUS
High Byte
INT
Note: For valid time in CPU
STATUS Low Byte = 1
STATUS High Byte = 1
z
z
208
Low byte is managed by the controller
Set = 0
z Clock value NOT available
z Date/time NOT updated within last two minutes
z Set = 1
z Date/time updated within the last two minutes
z Date/time acceptable
z
High byte is managed by the NOE
Set = 0
z Clock value transferred to CPU not acceptable
z Set = 1
Updated date/time received from server and sent to
module
z within two minute time interval
z acceptable (10 ms or less error)
z
Electronic Mail Notification
Service
10
At a Glance
Introduction
This chapter describes the electronic mail notification service, which uses the simple
mail transport protocol (SMTP) to allow the controller’s project to send e-mail
messages.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Introducing the Electronic Mail Notification Service
Page
210
Using the Mail Service
211
Using the MSTR Block for Mail Service Communication
212
Mail Service Error Codes
215
209
Using the Mail Service
Introducing the Electronic Mail Notification Service
General
The electronic mail notification service allows controller-based projects to report
alarms or events. The controller monitors the system and dynamically creates an
electronic mail message, which alerts local or remote users.
Mail System
Types
The simple mail transfer protocol provides two mechanisms for the transmission of
email messages:
z direct connection
z relay system
Mail Service
Client
Mechanism
Condition
Result
Direct
connection
sender and receiver are
connected to the same
transport service
Email messages are sent to host
Relay system
sender and receiver are
Email messages are relayed from one server
NOT connected to the same to another server
transport service
To relay messages, the SMTP server must
be supplied with the address of the
z destination host
z destination mailbox
The NOE and 140 CPU 651 x0 modules include an SMTP client. When the module
receives a specific request from the project, the module sends an email message to
the mail server.
CPS
CPU
NOE
SMTP
Server
MSTR
Email
Ethernet
OK or NOK
SMTP
Client
Operating Modes
and Sending
Requests
210
Because the project sends the email request, a controller cannot send an email
message either while in the stopped mode or while downloading a project. As soon
as the controller is in RUN mode, the function block sends a request during the first
project scan.
Diagnostic counters are reset to 0 after either a power-up, a project download, or a
reconfiguration of the mail service.
Using the Mail Service
Using the Mail Service
Configuring the
Mail Service
As an authorized administrator, use the SMTP Configuration Web page to
z configure the service
z set the IP address of the mail server
Note: Default TCP Port
The default TCP port number for SMTP is 25. Ensure that you configure the port specified by
your local mail server.
(See Configuring the Mail Service with the Email Configuration Page, p. 249)
Message
Creation and
Delivery
A user-defined event or condition triggers the MSTR block to create a message.
Each message uses one of three user-defined headers. Each message sent from
the controller can contain text and variable information (with a maximum of 238
bytes).
The project selects the appropriate header. Each header contains
z sender name
z list of recipients
z subject
Header
Examples
The text and variable information can be defined and updated by an authorized
administrator using an embedded Web page (SMTP Configuration page). Define
mail headers to indicate different levels of importance. For example,
z Header 1 could be "Urgent problem reported by PLC 10"
z Header 2 could be "NOTIFICATION from substation 10"
z Header 3 could be "INFO message from water system"
Listing different recipients in each of the three headers ensures that the right
information quickly flows to the right recipients. The project adds pertinent
information such as the specific device, process, or location. This pertinent
information is added to the body of the mail message. Then the complete message
is sent to an electronic mail server for distribution to recipients. These recipients
could be engineers, managers, or process owners.
Security
(Authentication)
An optional login (system ID) and password can be used to authenticate the
connection to the SMTP mail server. The SMTP-supported authentication method is
LOGIN.
System
Diagnostics
The SMTP Diagnostic Web page displays the status of the service. Diagnostic
information is also available for remote management using the SNMP network
management standard.
211
Using the Mail Service
Using the MSTR Block for Mail Service Communication
MSTR
Representation
212
Each operation is designated by a code. To send an email message, use the MSTR
block with Function Code 13.
Using the Mail Service
MSTR Parameter
Description
Description of parameters
Parameter
Data Type
Description
ENABLE
None
ON = enables selected MSTR operation
ABORT
None
ON = terminates active MSTR operation
ACTIVE
None
ON while the instruction is active
ERROR
None
ON if the MSTR operation is terminated prior to completion
SUCCESS
None
ON = operation successful
CONTROL
INT, UINT
Control block is the first of several network-dependant,
contiguous, holding words, and the first of nine contiguous words
entered in the top node.
The remaining eight words are:
Displayed: Identifies one of the MSTR = 13
First implied
Displays error status
(See Mail Service Error Codes, p. 215)
Second implied
Displays length
(number of words transferred)
Third implied
Not used
Fourth implied
High byte: slot address of the NOE module or
0xFE for the 140 CPU 651 x0
Low byte: 0
(Not used)
DATABUF
INT, UINT
Fifth implied
(Not used)
Sixth implied
(Not used)
Seventh implied
(Not used)
Eighth implied
(Not used)
The DATABUF parameter is the address of the buffer including
the data inserted into the body of the email message. The data
should be in ASCII format starting at the second word.
Note:
1. Least significant byte of the first word
Contains a valid (configured) mail header (should be of value
1, 2, or 3).
2. Most significant byte of the first word
Contains the length of the dynamic part of the message’s
subject field. The length must be between 0 and 238
characters.
213
Using the Mail Service
DATABUF
Parameter
Description
The first word of the DATABUF parameter contains the following information:
Byte Number
Value
1
Least significant byte
Mail header
{1,2,3}
2
Most significant byte
Nb n of extra characters in subject
User defined
(between 0 and 238)
The second and subsequent words (maximum 119) contain the data (ASCII format)
that will be copied into the email message. The first n characters will be added to the
configured email subject. The remaining characters (2*N-2-n) will be part of the
message body. N represents the number of words transferred.
The remaining characters
(2*N-2-n) will be a part of
the message body
214
{
{
{
The first n characters
will be added to the
message subject
Data in ASCII
N-1 words transferred
to the SMTP client
and part of the message
Using the Mail Service
Mail Service Error Codes
Error Codes
The electronic mail notification service supports the following error codes
Hex. Error Code
Description
5100
Internal error
5101
SMTP component not operational
5102
Mail Header not configured
5103
Invalid Mail Header value (should be 1, 2 or 3)
5104
Cannot connect to SMTP server
5105
Error in transmitting content of email body to SMTP server
5106
Closing SMTP connection with the server returned an error
5107
SMTP HELO request failed
5108
SMTP MAIL request failed. SMTP server may require authentication
5109
SMTP RCPT request failed
510A
No recipient has been accepted by the SMTP server
510B
SMTP DATA request failed
510C
Send email request contains an invalid length
510D
Authentication failed
510E
A Reset component request has been received while the connection
was open
215
Using the Mail Service
216
Embedded Web Pages
11
At a Glance
Introduction
This chapter presents the contents of the embedded Web pages contained in the
Quantum 140 NOE 771 xx modules. These Web pages enable you to access
diagnostic information, view configuration information, and change the online
configurations for the module.
217
Embedded Web Pages
What's in this
Chapter?
218
This chapter contains the following topics:
Topic
Page
Accessing the Web Utility Home Page
219
Quantum Welcome Page
221
Configured Local Rack Page
223
CPU Configuration Screen Page
224
Ethernet Module Statistics Page
227
Remote I/O Communication Status Page
228
Quantum PLC Data Monitor Page
229
Configure NOE Page
231
Configure SNMP Page
233
Configuring the Global Data (Publish / Subscribe) Utility
236
Configure Address Server Page
240
Configuring the Time Synchronization Service
244
Configuring the Electronic Mail Notification Service
249
Extended Web Diagnostics Pages
251
NTP Diagnostics Page
258
Email Diagnostics Page
260
NOE Properties Page
261
Crash Log Diagnostics
262
Contacting Schneider Electric Page
263
Embedded Web Pages
Accessing the Web Utility Home Page
Overview
The following information describes how to access the Web utility home page to
perform diagnostics and online configuration on the Modicon Quantum 10/100
Megabit Ethernet module.
Introduction
Each Modicon Quantum 10/100 Megabit Ethernet module contains an embedded
Web server that allows you to access diagnostics and online configurations for the
module and its associated controller (PLC).
Pages on the embedded Web site display the following information:
Configurable menus of the Address Server both BOOTP and DHCP and for SNMP
Ethernet statistics for the node
Controller’s configuration (Controller Status on menu)
Controller’s register values
Remote I/O status and configuration
Remote I/O register values
Remote I/O distributed values
The FactoryCast / Real Time modules offer these additional pages:
z Configuration and status for Global Data (Publish / Subscribe)
z Bandwidth monitoring
z I/O Scanner status
z MODBUS Messaging status
z NTP configuration and status
z SMTP configuration and status
The Web pages can be viewed using either Netscape Navigator or Internet Explorer
version 4.0 or higher. Either browser supports JRE 1.4.2_04 or higher.
For information about the additional functionality provided by the FactoryCast
system in the Ethernet modules, see the FactoryCast Manual.
219
Embedded Web Pages
Accessing the
Module’s Home
Page
Do the following.
Step
Action
1
Obtain the full IP address or URL from your system administrator.
2
Type the address or URL in the address or location box in the browser window.
The Schneider Electric Web Utility home page displays.
3
Refer to the following figure, and click Diagnostics and Online Configurations.
Schneider Automation Web Server
Diagnostics and Online Configurations
French
German
Italian
Spanish
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
220
4
You will be requested to supply a user name and password.
5
After supplying the user name, password, and clicking OK, the Quantum
Welcome Page appears. The Quantum Welcome Page provides the links to all
the Quantum configuration and diagnostic pages and to the Data Editor / Data
Monitor.
NOTE: The default User Name is USER, and the default password is USER.
Both should be changed by the system administrator during module installation.
Embedded Web Pages
Quantum Welcome Page
Overview
The following information describes the Quantum Welcome Page.
Quantum
Welcome Page
Overview and
Links
The Quantum Welcome Page provides links to all the Configuration and Diagnostic
Pages and to the Run-Time Data Editor.
The following figure shows the Quantum Welcome Page.
FactoryCast Web Server
for Quantum
Home
Configured Local Rack
Controller Status
Ethernet Statistics
RIO Status
Graphic Editor
Data Editor
Configure NOE
NOE Properties
NOE Diagnostics
Support
FactoryCastTM, Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
221
Embedded Web Pages
The following table details the links on the Quantum Welcome Page. To view the
pages related to a particular topic, click the link for that topic.
Link
222
Results
Home
Return to the home page
Configured Local Rack
Displays the Quantum Local Rack with NOE and CPU
Controller Status
Displays the CPU Configuration
Ethernet Statistics
Displays the Ethernet Module Statistics with the Reset
Counters link
RIO Status
Displays the Remote I/O Communications Status
Graphic Editor
Displays the Graphic tool for creating input / output user
screens (only with FactoryCast)
Only available on
z NOE 771 10
z NOE 771 11
z NWM 100 00
Data Monitor / Data Editor
Allows access to the Quantum PLC Data
Configure NOE
Provides the ability to configure and change the NOE
through the Ethernet Configuration page
NOE Properties
Provides information about the NOE properties
NOE Diagnostics
Displays the links to Ethernet Statistics and the Crash Log
File Diagnostics
Support
Displays contact information for technical assistance,
sales, and feedback
Embedded Web Pages
Configured Local Rack Page
Configured Local
Rack Page
Overview
The Configured Local Rack page displays a visual representation of the current
configuration.
The following table details the links on the Configured Local Rack Page. To view the
pages related to each of these topics, click on the topic.
Link
Results
Home
Displays the Quantum welcome page
Controller Status
Displays the CPU configuration
Ethernet Statistics
Displays the Ethernet module statistics with the reset
counters link
RIO Status
Displays the Remote I/O Communications Status
Graphic Editor
Displays the Graphic tool for creating input / output user
screens (only with FactoryCast)
Only available on
z NOE 771 10
z NOE 771 11
z NWM 100 00
Data Monitor / Data Editor
Allows access to the Quantum PLC Data with editing
capabilities
223
Embedded Web Pages
CPU Configuration Screen Page
Overview
The following information describes the CPU Configuration Screen Page.
Introduction to
the CPU
Configuration
Screen Page
In the following figure, the top eight fields identify the CPU Configuration. More
information about these fields follows.
CPU CONFIGURATION SCREEN
Status: Stopped
Battery: OK
Rack:
Slot:
DESCRIPTION
Reference: 140-CPU-651-50
Product Type: Quantum
Exec ID:
Logged In: No
REGISTERS
ASCII
System Memory[Kb]
(%M)
Total Words
Extended Memory[Kb]
(%I)
Total Messages
Total Memory [Bytes]
(%IW)
Words Used
I/O Map Words
Segments
(%MW)
Messages Used
Available Words
DCP Drop ID
Battery Coil
Available Messages
Memory Protect
Timer Register
# ASCII Ports
Constant Sweep
Optimize
Time of Day Clock
ASCII Inputs
Stopped Codes
ASCII Outputs
Home | Configured Local Rack | Ethernet Statistics | RIO Status | Data Monitor
Copyright  1998−2003, Schneider Automation. All Rights Reserved
224
Embedded Web Pages
Description
Fields
Word Fields
ASCII Fields
The following table describes the Description fields on the CPU Configuration
Screen Page.
Field
Information Supplied
System Memory [Kb]
Amount of system memory used
Extended Memory [Kb]
Amount of Extended Memory used
Number of I/O words mapped.
Total memory used in bytes
I/O Map Words
Number of I/O words mapped.
Segments
Number of segments
DCP Drop ID
Drop number for Distributed Control
Memory Protect
Position of the Memory Protect Switch
Constant Sweep
Current status of Constant Sweep
Optimize
Current status of Optimization
The following table describes the Word fields on the CPU Configuration Screen
Page.
Field
Information Supplied
%M
Valid Address of %M
%I
Valid Address of %I
%IW
Valid Address of %IW
%MW
Valid Address of %MW
Battery Bit
Address of Battery Bit
Timer Word
Address of Timer Word
Time of Day Clock
Address of Timer of Day Clock
Stopped Codes
Reason for controlled stopping
The column headed ASCII fields on the CPU Configuration Screen contains
information concerning the ASCII fields.
225
Embedded Web Pages
CPU
Configuration
Screen Page
Links
The following table describes the links on the CPU Configuration Screen Page.
Link
Results
Home
Displays the Quantum Welcome Page
Configured Local Rack Displays the Quantum Local Rack with NOE and CPU
226
Ethernet Statistics
Displays the Ethernet Module Statistics with the Reset Counters link
RIO Status
Displays the Remote I/O Communications Status
Graphic Editor
Displays the Graphic tool for creating input / output user screens
(only with FactoryCast)
Only available on
z NOE 771 10
z NOE 771 11
z NWM 100 00
Data Monitor
Allows access to the Quantum PLC Data with editing capabilities
Embedded Web Pages
Ethernet Module Statistics Page
Overview
The following information describes the Ethernet Module Statistics Page.
Introduction to
the Ethernet
Module Statistics
Page
The statistics on Ethernet Module Statistics Page are "information only". To retain
any of the information appearing on the Ethernet Module Statistics Page, you must
copy it offline (for example, to your hard drive).
The following figure shows the Ethernet Module Statistics Page. The counters may
be reset to zero by clicking the Reset Counter button.
ETHERNET MODULE STATISTICS
Status:
Running Link Appl
Host Name:
192.168.3.4
Reference:
140 NOE 771 11
MAC Address:
00 00 54 11 fa 55
Rack:
1
IP Address:
192.168.3.4
Slot:
4
Subnet Mask:
255.255.0.0
Transmit Speed:
100 MB
Gateway Address: 192.168.3.4
Transmit Statistics
Receive Statistics
Functioning Errors
Transmits
78
Receives
128
Missed Packets
0
Transmit Retries
0
Framing Errors
0
Collision Errors
0
Lost Carrier
0
Overflow Errors
0
Transmit Timeouts 0
Late Collision
0
CRC Errors
0
Memory Errors
Transmit Buffer Errors
0
Silo Underflow
Receive Buffer Errors
0
0
0
Net Interface Restarts
0
0
0
Reset
Home
Configured Local
Controller
RIO Status
Graphic
Data Editor
FactoryCastTM, Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
227
Embedded Web Pages
Remote I/O Communication Status Page
Overview
The following information describes the Remote I/O Communication Status Page.
Introduction to
the Remote I/O
Communications
Status Page
In the following figure, the fields are "information only". You cannot change the
fields.
REMOTE I/O COMMUNICATION STATUS
Global Status:
Global Health:
OK
OK
Cable A
Description
Startup Errors
Cable A: OK
Cable B: Not OK
Cable B LAN Errors Cable A
Framing Errors
Short Frame
No EOF
DMA Receive Overruns
CRC
Receive Errors
Bad Drop Reception
Alignment
Overruns
Cable B
Global Communications
Cable A Cable B
Global Communication Status OK
Not OK Global Communication Health
Detected Error Count
Lost Communications Count
Global No Response Count
Total Retry Count
OK
Home | Configured Local Rack | Controller Status | Ethernet Statistics | Graphic Editor | Data Editor
FactoryCast  , Schneider Automation, Inc., 1998−1999
Note: The Graphic Editor Link is available only on the 140 NOE 771 1x, the FactoryCast Web
server.
For more information about the Remote I/O Communications Status, see the RIO
Manual.
Remote I/O
Communications
Status Page
Links
The following table describes the information that is available for each cable, using
the links on the Remote I/O Communication Status Page.
Link
Results
Home
Displays the Quantum Welcome Page
Configured Local Rack Displays the Quantum Local Rack with NOE and CPU
228
Controller Status
Displays the CPU Configuration
RIO Status
Displays the Ethernet Module Statistics with the Reset Counters link
Data Monitor
Allows access to the Quantum PLC Data with editing capabilities
Embedded Web Pages
Quantum PLC Data Monitor Page
Introduction to
the PLC Data
Monitor Page
The following figure shows the web page that allows you to display Quantum PLC
data.
Quantum PLC Data Monitor
<new>
Address
Data Type
Insert Rows Cut Rows Paste Rows
Value
Format
Status
Home | Configured Local Rack | Controller Status | Ethernet Statistics | RIO Status
Copyright  1999, Schneider Automation, Inc. All Rights Reserved
You can add, delete, and copy Quantum PLC data as described in the following list:
z You can insert additional rows of data by clicking on the Insert Rows button.
z You can delete specific rows of data by clicking on the Cut Rows button.
z You can copy in rows of data by clicking on the Paste Rows button.
229
Embedded Web Pages
PLC Data
Monitor Page
Links
230
The following table describes the links on the Quantum PLC Data Monitor Page.
Link
Results
Home
Displays the Quantum Welcome Page
Configured Local Rack
Displays the Quantum Local Rack with NOE and CPU
Controller Status
Displays the CPU Configuration
RIO Status
Displays the Remote I/O Communications Status
Graphic Editor
Displays the Graphic tool for creating input / output user screens
(only with FactoryCast)
Only available on
z NOE 771 10
z NOE 771 11
z NWM 100 00
Embedded Web Pages
Configure NOE Page
Overview
The following information describes the Configure NOE page and the links on that
page.
Introduction to
the NOE
Configuration
Pages
The following figure shows the Configure NOE page, which provides links to the
individual configuration pages for the NOE.
Configure NOE
Configure SNMP
Configure Address Server
Configure Global Data
Configure NTP
Configure Email
Home
NOE Properties
NOE Diagnostics Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
231
Embedded Web Pages
NOE
Configuration
Page Links
232
The following table describes the links on the Configure NOE page.
Link
Results
Configure SNMP
Provides the ability to configure the SNMP Agent in the NOE
Configure Address Server
Configure the BOOTP IP assignments, including showing the
BOOTP and DHCP database
Configure Global Data
Displays the Global Data Configuration page. Configure the
Group Address, Multicast filtering, Distribution period, Health
Time Out, Health Bits, and Data Zones. The Global Data
Configuration page also displays a Variable Table.
Configure NTP
Configure the IP address of the primary and secondary NTP
server. Set a polling period. Select a time zone from the dropdown list, and automatic adjustment for daylight savings time.
Configure Email
Configure the email server’s IP and Port (default port is 25). If
security required, select Enable and set a Login and Password.
Create three mail headers.
Home
Returns you to the Quantum Welcome Page
NOE Properties
Provides information about NOE properties
NOE Diagnostics
Displays links to Ethernet Statistics and the Crash Log File
Diagnostics
Support
Provides you with contact information for technical assistance,
sales, and feedback
Embedded Web Pages
Configure SNMP Page
Introduction to
the Configure
SNMP Page
SNMP may already be configured on your NOE 771 xx. If it is not, complete the
SNMP Configuration form, which is shown in the following figure.
System Name: 140-NOE-771-01 Module
System Description: Quantum Ethernet TCP/IP Communications Module
Managers IP Addresses
Manager I: 192.168.1.100
Manager II: 0.0.0.0
Agent
Location [SysLocation]: Test_Setup_1
Contact [SysContact]: Julien
Community
Set: NonTriv1
Security
Authentication Failure Trap Enabled
Get: NonTriv2
Trap: NonTriv3
Reset the Form
Update SNMP
Show SNMP Configuration
The following table shows how to enter the required information for configuring
SNMP on your NOE 771 xx.
Task
How To
To display the current SNMP configuration Click Show SNMP Configuration
To clear the fields
Click Reset the Form
To change the SNMP configuration
Change the information on the page and click
Update SNMP
233
Embedded Web Pages
SNMP Page
Fields
Configure SNMP
Page Links
Completion
Message
The following table describes the specific SNMP fields that you can modify.
Field
Information To Be Supplied
Manager I
IP Address of first SNMP Manager
Manager II
IP Address of second SNMP Manager
Location [SysLocation]
Location of the module
Contact [SysContact]
Name of the responsible systems engineer
Set
Designation of level of user who can set the configuration
Get
Designation of level of user who can view the configuration
Trap
Designation of level of user who can capture information
Authentication Failure Trap
Enabled
Turns on Community Name Checking
The following table describes the links on the Configure SNMP Page.
Link
Results
Home
Returns you to the Modicon Quantum Welcome Page.
Configure NOE
Provides the ability to configure and change the NOE through the
Ethernet Configuration Page.
NOE Properties
Provides information about NOE properties
NOE Diagnostics
Displays links to Ethernet Statistics and the Crash Log File Diagnostics
Support
Provides you with contact information for technical assistance, sales, and
feedback
Clicking on the Update SNMP button displays a new page containing the message
"Successfully updated SNMP database". Note that this page contains the same links
as those on the Configure SNMP Page.
Note: The NOE module has to be reset for the changes to take effect.
SNMP
Community
Strings
234
Use strings to restrict access to the SNMP Agent. These strings should be set to
Non-Trivial names during module installation.
Embedded Web Pages
Modifying the
SNMP
Community
Strings
The following steps should be used to establish the SNMP Community Strings:
Step
Action
1
Enter the URL into your browser:
http://hostname/secure/embedded/builtin?submit=Configure+SNMP
or navigate to the SNMP Configuration Web page
2
Enter the Community names for Set, Get, and Trap into the SNMP
Configuration Web page as shown below.
System Name: 140-NOE-771-01 Module
System Description: Quantum Ethernet TCP/IP Communications Module
Managers IP Addresses
Manager I:
Manager II:
Agent
Location [SysLocation]:
Contact [SysContact]:
Community
Security
Set: NonTriv1
Authentication Failure Trap Enabled
Get: NonTriv2
Trap: NonTriv3
Reset the Form
Update SNMP
Show SNMP Configuration
3
Click Update SNMP.
4
After making changes in the SNMP Configuration Web page and to set those
changes, reboot the module using hot swap.
235
Embedded Web Pages
Configuring the Global Data (Publish / Subscribe) Utility
Overview
Whether you use the Configure Each Device Separately or the Copy Configuration
method, the procedure to configure individual parameters is the same. Therefore, in
order to use the Global Data (Publish / Subscribe) utility in the NOE, you need to
configure the Global Data parameters including:
z
z
z
z
z
Distribution period
Multicast filtering
Health bit location
Global Data base address
Group IP address
The following sections describe in detail the exact steps to configure each parameter
via the Global Data Configuration page.
Accessing the
Global Data
Utility
You access the Global Data utility through the Global Data Configuration page.
Step
1
Action
On your screen click the Diagnostics and Online Configurations link.
Schneider Automation Web Server
Diagnostics and Online Configurations
French
German
Italian
Spanish
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
236
2
When you click the Diagnostics and Online Configurations link, you are
requested to enter user name and password
3
Enter your user name and password. The Configure NOE page appears.
4
Click the Configure NOE link.
The Configure NOE page appears.
Embedded Web Pages
Step
5
Action
Click the Configure Global Data link.
Configure NOE
Configure SNMP
Configure Address Server
Configure Global Data
Configure NTP
Configure Email
Home
NOE Properties
NOE Diagnostics Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
6
The Global Data Configuration page appears.
Global Data Configuration
Group 239 . 200 . 255 . 255
Health
100
m
Multicast filtering
Health %M 4
to 7
Distribution 5
Data
%M 0
scan
to 5
Update Global Data Configuration
Variable Table
Data
1
2
3
4
5
6
7
8
9
Type
SU
PU
SU
NO
NO
NO
NO
NO
NO
Symbol
var_01
var_02
var_03
Address
%M 48
%M 60
%M 44
%M
%M
%M
%M
%M
%M
Lenght
2
2
2
In this screen you may make changes to the configuration.
237
Embedded Web Pages
Configuring
Global Data
After you have completed the Modelling System Configuration process using the
second method, Copy Configuration, then you modify the following parameters:
z Distribution period
z Health Time Out
z Health Bits location
z Start address
z Type: Pub / Sub / None
Please do NOT change Symbol (description), and Length.
To change the Global Data variables of the group box on the Global Data
Configuration page, follow the instructions below.
Step
Action
1
Adjust the Distribution Period Cycle. Enter a value from 1 through 50.
Note: Distribution period is the minimum number of controller scan times
before an update will occur.
2
Before entering a value in the Group address field, identify the station’s
distribution group. The Group address entry will be an IP address from
224.0.0.0 through 239.255.255.255.
Group address: the Class D Multicast IP address used for a distribution group.
All members of this distribution group are configured to use the same group
address, and therefore, all members can communicate with each other using
Global Data.
3
Set the timeout in the Health Time Out field. This value is measured in
milliseconds and can be set to a value that ranges from 50 through 1000 ms
(increase in units of 50ms).
Note: Validity Time is the maximum time between received subscriptions
before a subscription is declared unhealthy (faulty).
4
In the 4x Starting Address set the Data Zone field.
5
If you are connected to an Ethernet switch that supports multicast filtering, click
the Multicast filtering check box.
6
Enter 4x Register Location for the Health Bits. This is the register where the
health bit will be stored
Note: Health bits run in different directions.
z I/O scanner health bits run left to right.
z Global Data health bits run right to left.
238
Embedded Web Pages
Changing Global
Data Variables
To change the Global Data variables that appear in the Variable Table area, follow
the instructions below.
Step
Verifying System
Operation
Action
1
Highlight the identification number in the Data ID column.
2
In the Type column select the publish / subscribe variable type from the drop
down list.
Three options are available publish, subscribe, or none. These options display
on the screen as follows:
z NONE
z SUB
z PUB
3
In the Symbol column you may enter text to describe the variable.
4
In the Address column you see the application address for this variable.
Note: This is a read only field.
5
In the Length column for each row, type a value, which represents the number
of 4x registers. The ending 4x register field is automatically updated. If you are
using the second method, Copy Configuration, you update Length the first
time only.
6
When you are finished, click the Update Global Data Configuration button.
To ensure that the system is operational, do the following:
Step
Action
1
Verify all controllers are running.
2
Look at the health of all variables using the Global Data Diagnostics page.
Follow these links:| Diagnostics and Online Configuration | NOE Diagnostics
| Global Data
239
Embedded Web Pages
Configure Address Server Page
Overview
The following information describes how to configure the Address Server for the
Transparent Factory Ethernet modules.
Note: For information describing how to configure the Address Server for the 140
NOE 771 x1, FactoryCast Web server modules, see the chapter entitled Address
Server Configuration / Faulty Device Replacement. That chapter describes the
BOOTP process.
Introduction to
the Configure
BOOTP Initial
Page
The BOOTP Database File does not exist. Therefore, you need to create the
database. Use the Ethernet Configuration page to create a BOOTP database file.
Select Configure Bootp Entry.
Ethernet Configuration
No Bootp Database File Exists. Please click button to configure it.
Configure Bootp Entry
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright  1999, Schneider Automation, Inc. All Rights Reserved.
240
Embedded Web Pages
Displaying the
Bootp Node
Configuration
Form Page
The following information describes how to complete the Bootp Node
Configuration page.
Step
1
Action
Click the Configure Bootp Entry button on the Ethernet Configuration page
to configure a BOOTP Database File.
Result: As the following figure shows, the Bootp Node Configuration page
appears.
Bootp Node Configuration
Hostname
Host IP Address
Host Mac Address
Subnet Mask
Gateway
Add a New Entry
Change an Entry
Delete an Entry
Reset the Form
Show Bootp Database
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright  1999, Schneider Automation, Inc. All Rights Reserved
2
Initial
Configuration
If this is an initial BOOTP configuration, fill in the fields on the Bootp Node
Configuration page and click the Add a New Entry button.
The following table describes the fields to complete on the BOOTP configuration
form.
Field
Information to be Supplied
Hostname
Text to identify device
Host IP address
IP Address from System Administrator - read from sticker on device
Host Mac Address IEEE Global Address
Subnet Mask
Supplied by system administrator and configured on the server by the
system administrator
Gateway
Define the address of route to use to access nodes off the devices
subnet
241
Embedded Web Pages
Adding to the
BOOTP
Database File
If you want to add an entry to the BOOTP Database File, complete the fields on the
form, and press the Add a New Entry button.
Changing the
BOOTP
Database File
The following steps describe how to change an entry in the BOOTP Database File.
Deleting the
BOOTP
Database File
Resetting the
Form
242
Step
Action
1
Enter the new information on the Bootp Node Configuration page
2
Click on the Change an Entry button.
Result: The a new entry will be made at the bottom of the Database Table, and
you will get a successful entry message.
3
Click on Configure NOE to return to the Configure NOE page.
4
Click on Configure BOOTP.
5
Enter the information to be old information.
6
Click on Delete an Entry.
The following steps describe how to delete an entry in the BOOTP Database File.
Step
Action
1
Enter the new information for the item to be deleted.
2
Click on the Delete an Entry button.
Result: A delete successful message is displayed.
3
Click on Configure NOE to return to Configure NOE page.
4
Click on Configure BOOTP.
5
Click on Refresh Bootp Database Table to view revised Database file.
To clear the fields in the Bootp Node Configuration page, press the Reset the
Form button. You will then be able to fill in the Database File entries information to
be added, changed, or deleted.
Embedded Web Pages
Displaying the
BOOTP
Database File
The following figure shows a sample current BOOTP Database File. To display the
current BOOTP Database File, press the Show Bootp Database button.
Bootp Configuration
Host Name
IP Address
Subnet Mask
Gateway
Mac Address
ENT1
ENT2
ENT4
ENT3
Refresh Bootp Database Table
Configure Bootp Entry
Home | Configure NOE | NOE Properties | NOE Diagnostics | Support
Copyright  1999, Schneider Automation, Inc. All Rights Reserved
Configure
BOOTP Page
Links
The following table describes the links on the Bootp Node Configuration page
Page.
Link
Results
Home
Returns you to the Quantum Welcome Page
Configure NOE
Provides the ability to configure and change the NOE through the
Ethernet Configuration Page
NOE Properties
Provides information about NOE properties
NOE Diagnostics
Displays links to Ethernet Statistics and the Crash Log File Diagnostics
Support
Provides you with contact information for technical assistance, sales,
and feedback.
243
Embedded Web Pages
Configuring the Time Synchronization Service
Configuring the
Time Service
with the NTP
Configuration
Page
You must use the module’s embedded Web page to configure the time service. No
other method is available.
NTP Configuration
NTP Server Configuration
IP Address of Primary NTP Server:
192.168.5.100
IP Address of Secondary NTP Server:
0.0.0.0
Polling Period:
15
sec
Time Zone
(GMT-05:00)Eastern Standard Time[New York]
Automatically adjust clock for daylight saving change
Save
Home
Cancel
Configure NOE
Disable NTP
NOE Properties
NOE Diagnostics
Support
Copyright © 2001, Schneider Automation Inc. All rights reserved.
Time Service
Command
Buttons
244
Execute the following commands
Command Button
Description
Save
Stores new NTP (time service) configuration. Previous configuration is
no longer valid.
Cancel
Cancels new NTP (time service) configuration. Previous configuration
is valid
Disable NTP
IP of Primary and Standby set = 0.
NTP server not polled
Time in controller not updated.
Embedded Web Pages
Configurable
Time Service
Parameters
Configure or change the following parameters on the NTP Configuration page.
1. IP address of primary NTP server
z Enter a valid IP address
2. IP address of secondary NTP server
z Enter a valid IP address
3. Polling Period (in seconds)
Enter a value
z min = 1sec
z max = 120sec
z default = 5 sec
4. Time Zone
z Select from drop-down menu
Universal Time, Coordinated (GMT) = default
z Custom time zone
5. Automatically adjust clock for daylight saving change
z Parameter is selected by default (check mark appears) if daylight saving time
is chosen.
Changing Time
Service
Parameters
To make any changes to the time synchronization service,
Important
Information
about the Time
Service
Step
Action
1
Enter changes in the appropriate field on the NTP Configuration page for one or
all of the configurable parameters.
2
Click Save.
Note: About the Time Service
1. Enable/Disable Daylight Savings Time parameter
If the Enable/Disable check box is selected, the module automatically corrects
the local time to account for daylight savings time. Therefore, requiring no
action, as the daylight savings time start and end are automatically changed
each year.
2. Polling Time Parameter
The time (in seconds) is the time between time updates from the NTP server.
The default is 5 Seconds.
3. Storing the Time Service Configuration
The last time service configuration is saved internally in the Ethernet module.
4. Replacing the Ethernet Module
If the Ethernet module has to be replaced, the stored configuration is lost, and
the system returns to the default configuration.
245
Embedded Web Pages
Customizing
Time Zone
Parameters
Time Zone
Parameters
If you want a time zone not listed in the time zone table,
Step
Action
Comment
1
Write the text rules for the custom time zone.
2
Using an FTP client, store your rules in the
file:
/FLASH0/wwwroot/conf/NTP/customrules
user ID: ntpupdate
password: ntpupdate
Root directory to store 'customrules' is
set by the FTP server as
/FLASH0/wwwroot/conf/NTP
3
When the rules are written, choose the drop
down menu on the NTP Configuration web
page, and configure (or reboot) the module
by selecting
Time Zone = Custom
The NTP component looks for
customrules, calls the tz compiler and
generates a new file called
'tz_custom'. This file is binary file and
should not be edited.
If the tz compiler detects a syntax
error in customrules, the error is
logged in the file:
/FLASH0/wwwroot/conf/NTP/
error.log
1. NTP component is not launched
2. NTP Status field in diagnostic web
page displays NOT OK.
4
If you want more information, the syntax to write those rules along with a few
examples are found in the module in
/FLASH0/wwwroot/conf/NTP/instructions.txt
Select one from drop-down menu.
Time Zone
Description
Custom
246
DST Available
Yes
(GMT-12:00)
Dateline Standard Time [Eniwetok Kwajalein]
No
(GMT-11:00)
Samoa Standard Time [Midway Is Samoa]
No
(GMT-10:00)
Hawaiian Standard Time [Hawaii Honolulu]
No
(GMT-09:00)
Alaskan Standard Time [Anchorage]
Yes
(GMT-08:00)
Pacific Standard Time [Los Angeles Tijuana]
Yes
(GMT-07:00)
Mexican Standard Time [Chihuahua La Paz Mazatlan]
Yes
(GMT-07:00)
Mountain Standard Time [Arizona Phoenix]
No
(GMT-07:00)
Mountain Standard Time [Denver]
Yes
(GMT-06:00)
Central Standard Time [Chicago]
Yes
(GMT-06:00)
Mexico Standard Time [Tegucigalpa]
No
(GMT-06:00)
Canada Central Standard Time [Saskatchewan Regina]
No
Embedded Web Pages
Time Zone
Description
DST Available
(GMT-06:00)
Central America Standard Time [Mexico_city]
Yes
(GMT-05:00)
SA Pacific Standard Time [Bogota Lima Quito]
No
(GMT-05:00)
Eastern Standard Time [New York]
Yes
(GMT-05:00)
Eastern Standard Time [Indiana (East)] [Indianapolis]
No
(GMT-04:00)
SA Western Standard Time [Caracas La Paz]
No
(GMT-04:00)
Pacific SA Standard Time [Santiago]
Yes
(GMT-03:30)
Newfoundland Standard Time [Newfoundland St Johns]
Yes
(GMT-03:00)
E. South America Standard Time [Brasilia Sao_Paulo]
Yes
(GMT-03:00)
SA Eastern Standard Time [Buenos Aires Georgetown]
No
(GMT-02:00)
Mid-Atlantic Standard Time [South_Georgia]
No
(GMT-01:00)
Azores Standard Time [Azores Cape Verde Island]
Yes
(GMT)
Universal Coordinated Time [Casablanca, Monrovia]
No
(GMT0)
Greenwich Mean Time [Dublin Edinburgh Lisbon London]
Yes
(GMT+01:00)
Romance Standard Time [Amsterdam CopenHagen Madrid Yes
Paris Vilnius]
(GMT+01:00)
Central European Standard Time [Belgrade Sarajevo
Skopje Sofija Zagreb]
Yes
(GMT+01:00)
Central Europe Standard Time [Bratislava Budapest
Ljubljana Prague Warsaw]
Yes
(GMT+01:00)
W. Europe Standard Time [Brussels Berlin Bern Rome
Stockholm Vienna]
Yes
(GMT+02:00)
GTB Standard Time [Athens Istanbul Minsk]
Yes
(GMT+02:00)
E. Europe Standard Time [Bucharest]
Yes
(GMT+02:00)
Egypt Standard Time [Cairo]
Yes
(GMT+02:00)
South Africa Standard Time [Johannesburg Harare
Pretoria]
No
(GMT+02:00)
FLE Standard Time [Helsinki Riga Tallinn]
Yes
(GMT+02:00)
Israel Standard Time [Israel Jerusalem]
Yes
(GMT+03:00)
Arabic Standard Time [Baghdad]
Yes
(GMT+03:00)
Arab Standard Time [Kuwait Riyadh]
No
(GMT+03:00)
Russian Standard Time [Moscow St. Petersburg
Volgograd]
Yes
(GMT+03:00)
E. Africa Standard Time [Nairobi]
No
(GMT+03:30)
Iran Standard Time [Tehran]
Yes
(GMT+04:00)
Arabian Standard Time [Abu Dhabi Muscat]
No
(GMT+04:00)
Caucasus Standard Time [Baku Tbilisi]
Yes
247
Embedded Web Pages
Time Zone
248
Description
DST Available
(GMT+04:00)
Afghanistan Standard Time [Kabul]
No
(GMT+05:00)
Ekaterinburg Standard Time [Ekaterinburg]
Yes
(GMT+05:00)
West Asia Standard Time [Islamabad Karachi Tashkent]
No
(GMT+05:30)
India Standard Time [Bombay Calcutta Madras New Delhi] No
(GMT+06:00)
Central Asia Standard Time [Almaty Dhaka]
Yes
(GMT+06:00)
Sri Lanka Standard Time [Columbo]
No
(GMT+07:00)
SE Asia Standard Time [Bangkok Hanoi Jakarta]
No
(GMT+08:00)
China Standard Time [Beijing Chongqing Hong Kong
Urumqi]
No
(GMT+08:00)
W. Australia Standard Time [Perth]
No
(GMT+08:00)
Singapore Standard Time [Singapore]
No
(GMT+08:00)
Taipei Standard Time [Taipei]
No
(GMT+09:00)
Tokyo Standard Time [Osako Sapporo Tokyo]
No
(GMT+09:00)
Korea Standard Time [Seoul]
No
(GMT+09:00)
Yakutsk Standard Time [Yakutsk]
Yes
(GMT+09:30)
Cen. Australia Standard Time [Adelaide]
Yes
(GMT+09:30)
AUS Central Standard Time [Darwin]
No
(GMT+10:00)
E. Australia Standard Time [Brisbane]
No
(GMT+10:00)
AUS Eastern Standard Time [Canberra Melbourne Sydney] Yes
(GMT+10:00)
West Pacific Standard Time [Guam Port Moresby]
No
(GMT+10:00)
Tasmania Standard Time [Hobart]
Yes
(GMT+10:00)
Vladivostok Standard Time [Vladivostok]
Yes
(GMT+11:00)
Central Pacific Standard Time [Magadan Solomon Is New
Caledonia]
Yes
(GMT+12:00)
New Zealand Standard Time [Auckland Wellington]
Yes
(GMT+12:00)
Fiji Standard Time [Fiji Kamchatka Marshall Is]
No
Embedded Web Pages
Configuring the Electronic Mail Notification Service
Configuring the
Mail Service with
the Email
Configuration
Page
You must use the module’s embedded Web page to configure the electronic mail
notification service. No other method is available.
Email Configuration
Email Server Configuration
IP Address of Email Server: 192.168.3.1
Port: 25
Password Authentication
Enable
Login:
knight
Password:
**********
Mail Header 1
From:
NOE_Pump2
To:
[email protected]
Subject:
Alarm 4: water level low
Mail Header 2
From:
Statio_N4
To:
[email protected]
Subject:
Warning: big problem with Pump2
Mail Header 3
From:
To:
Subject:
Save
Cancel
Disable Email
249
Embedded Web Pages
Mail Service
Command
Buttons
Configurable
Mail Service
Parameters
Mail service configuration buttons
Command Button Description
Save
Saves the new Email configuration.
Note: Previous configuration is not valid. Previous configuration is not
stored.
Cancel
Cancels the entries in the fields.
Previous configuration is valid.
Disable Email
Clears the stored configuration, and disables the email service.
Note: Next time the service is enabled, a new configuration is required.
Configure the following parameters.
Parameter
Description
IP address of Email
Enter a valid IP address
This parameter identifies SMTP server.
Port
Default = 25
If needed, enter a new value.
Password Authentication
If security is needed, enable Password Authentication.
To enable, enter a check mark in the box.
Enter values for
z Login
z Any printable character allowed
z 12 character maximum
z Password
z Any printable character allowed
z 12 character maximum
3 mail headers
Each header must contain
1. sender’s ID in the "From:" field
z 32 character maximum; no spaces
2. list of recipients in the "To:" field
z Separate each email address with a comma.
z 128 character maximum
3. fixed part of message in the "Subject:" field1.
z (32 character maximum)
1. Subject field consists of two parts:
1. Fixed
z 32 character maximum
2. Dynamic
z 206 character maximum
(See DATABUF Parameter Description, p. 214)
250
Embedded Web Pages
Extended Web Diagnostics Pages
Overview
The 140 NOE 771 x1 embedded Web server provides Web pages that you may use
to diagnose Transparent Factory / Real Time services. Those services are listed
below:
z Global Data Diagnostics
z Status of all Global Data services
z Status of all subscribed and published variables
z Publication / Subscription rate
z I/O Scanning Diagnostics
z Status of all I/O Scanning services
z Status of individual scanned devices
z Actual I/O scanning rate
z Messaging Diagnostic
z Diagnostic information for Modbus (port 502) messaging
z Bandwidth Monitoring
z Throughput measurement of NOE by service
z Time Synchronization Service
z Status of NTP server
z Date and time
z Status of daylight savings time option (DST)
z Electronic Mail Notification Service
z Status of SMTP server
z Track messages sent and received
z Track errors
Note: All these pages are protected by the general HTTP password.
251
Embedded Web Pages
Accessing Web
Diagnostics
You access the diagnostic Web pages through the Web Server for Quantum page.
FactoryCast Web Server
for Quantum
Home
Configured Local Rack
Controller Status
Ethernet Statistics
RIO Status
Graphic Editor
Data Editor
Configure NOE
NOE Properties
NOE Diagnostics
Support
FactoryCastTM, Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
On this page select the NOE Diagnostics link, which opens the NOE Diagnostics
page.
252
Embedded Web Pages
On the NOE Diagnostics page select the desired service by clicking the appropriate
link.
NOE Diagnostics
Global Data
I/O Scanning
Messaging
Bandwidth Monitoring
Ethernet Statistics
NTP Diagnostics
Email Diagnostic
Upload MIB File
Crash Log File
Home
Configure NOE
NOE Properties
NOE Diagnostics Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
The first four links are the diagnostics.
Global Data
IO Scanning
Messaging
Bandwidth Monitoring
The last five links access other functions.
z Ethernet Statistics
z NTP Diagnostics
z Email Diagnostics
z Upload MIB File
z Crash Log File
z
z
z
z
253
Embedded Web Pages
Global Data
Diagnostics
Page
This is the Global Data Diagnostics page.
This page displays information generated by the Global Data service. At the top of
the page the following three items appear:
z Global Data status
z Number of subscriptions per second
z Number of publications per second
The above information is displayed both as text and as a graphic.
This page also displays the complete status for all variables published and
subscribed within the same distribution group. Every variable is identified by its data
ID. At the bottom of the page four boxes display indicating the status of the variables.
Those boxes are color coded.
z White for all non configured variables
z Green for the healthy subscribed variables
z Black for the healthy published variables
z Red for a communication fault
If Red displays in the Fault variable box, you should check the system for problems.
The Global Data status indicator displays OK, even if there are unhealthy
variables.
254
Embedded Web Pages
I/O Scanning
Diagnostic Page
This page displays information generated by the I/O Scanning service.
I/O Scanning Diagnostics
I/O Scanning status : OK
Number of transactions per sec : 311 | Number of connections : 1
SCANNED DEVICES STATUS
1
16
17
32
33
48
49
64
Non-Configured
Home
Scanned
Configure NOE NOE Properties
Fault
NOE Diagnostics
Support
Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
At the top of the page the following three items appear:
z I/O Scanning status
z Number of transactions per second
z Number of connections
The above information is displayed both as text and as a graphic.
At the bottom of the page four boxes display indicating the status of the devices.
Those boxes are color coded.
z White for all non configured devices
z Green for all scanned devices
z Black for all temporary unscanned devices
z Red for all devices in a default state
If Red displays in the Fault variable box, you should check the system for problems
255
Embedded Web Pages
Messaging
Diagnostic Page
This page provides information concerning current open TCP connections on Port
502. The total number of messages sent and received on Port 502 displays on the
top of this page.
Note: Please note the following.
z After a port 502 connection is closed, the connection will remain on the list for
several minutes.
z The total message counter is not reset after a port 502 connection is closed.
z The I/O status indicator displays OK, even if there are unhealthy faulted
scanned devices.
The Messaging Diagnostic page:
Modbus Messaging Diagnostics
Number of Messages sent : 21634 | Number of Messages received : 21651
Conn.
Remote address Remote port Local port
Mess. Sent Mess. Received Error Sent
1
192.168.3.1
4524
502
9143
9144
0
2
192.168.3.1
4563
502
13
13
0
Home Configure NOE NOE Properties
NOE Diagnostics Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
For each connection (numbered from 1 to 64) the following information is given:
z Remote address (IP address)
z Remote port (TCP)
z Local port (TCP)
z Number of messages sent (Mess. Sent) on this connection
z Number of messages received (Mess. Received) on this connection
z Number of errors (Error Sent) on this connection
256
Embedded Web Pages
Bandwidth
Monitoring Page
The Bandwidth Monitoring page indicates how the NOE’s CPU is shared between
the Global Data service, the I/O Scanner service, and the Messaging service. The
information generated by this service displays both as a graphic and as text. The
information generated gives you a view of the allocation of service usage. Knowing
the allocation of services can help you to determine the number of and the
distribution of NOEs on your system.
The Bandwidth Monitoring page:
Bandwidth Monitoring
Global Data : 16 | I/O Scanning : 5 | Messaging : 15 | Other : 64
Global Data
I/O Scanning
Modbus Messaging
Other/Unused
Home Configure NOE NOE Properties NOE Diagnostics Support
Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
The page reports four statistics one each for the three services and one for "other."
z Blue: Global Data (usage expressed as a % of maximum number of messages/
second)
z Yellow: I/O Scanner (usage expressed as a % of maximum number of messages/
second)
z Green: Modbus Messaging (usage expressed as a % of maximum number of
messages/second)
z Gray: Other/Unused (usage expressed as a % of maximum number of
messages/second.)
Percentages add to 100%.
257
Embedded Web Pages
NTP Diagnostics Page
NTP Diagnostic
Dialog
Time synchronization service parameters:
Parameter
Description
NTP status
Service is correctly configured (OK)
NTP server status
NTP client is connected to the NTP server, and if the server is Primary
or Standby
NTP requests
Total number of client requests sent to the NTP server
NTP responses
Total number of server responses sent from the NTP server
Number of errors
Total number of unanswered NTP requests
Last error code
Last error code received from the NTP client
Date
Date in d/m/y format
Time
Time
Time zone
Time zone plus or minus Universal Time, Coordinated (UTC)
DST
Daylight saving time (DST) parameter is either
1. on (enabled)
2. off (disabled)
The dialog:
NTP Diagnostics
OK
NTP Status:
NTP Server Status
###
Link to the NTP Server:
Server:
Server Time Quality within
0
microsec/sec
Primary
NTP Request Statistic
Number of Requests: 2
Number of Errors: 0
Number of Responses: 2
Last Errors: 0
NTP Date and Time
Date:
05 Apr 2004
Time Zone:
Time:
16:51:15
DST Status:
(GMT-05:00)Eastern Standard Time[New York]
Home
Configure NOE
NOE Properties
NOE Diagnostics Support
Copyright © 2001, Schneider Automation Inc. All rights reserved.
258
ON
Embedded Web Pages
Last Error Field
Last Error field displays values, which indicate the type of error.
Type of Error
Value
Component OK and running
0
Excessive network traffic or server overload
1
Bad parameters in the configuration
3
Component is disabled
4
Incorrect IP
9
Time zone file absent
14
Syntax error in the customrules file
15
259
Embedded Web Pages
Email Diagnostics Page
Email
Diagnostics
The dialog
Email Diagnostic
Email Status: OK
Link to Server Status:
SMTP Server IP Address:
Number of e-mail sent:
Number of Responses from SMTP Server:
Number of Errors:
Last Errors:
Last Mail Header Used:
Number of seconds elapsed since last e-mail successfully sent:
Number of times the link to the server has been detected down:
Electronic mail notification service parameters
Parameter
Description
Email status
Email service is correctly configured (OK).
Link to Server Status
Ethernet module is connected to the SMTP server
Status is checked at start-up and at least every 30
minutes after start-up
z Green = module connected to server
z Red = module NOT connected to server
SMTP Server IP Address
IP address of the SMTP server
Number of e-mails sent
Total number of emails sent successfully
Number of Responses from SMTP Total number of SMTP messages received from the
Server
SMTP server
Number of Errors
Total number of e-mails NOT sent because of an error
Last Errors
Reason for the last error with a code in hexadecimal.
0 displays if no error occurs
Last Mail Header Used
Last header used by giving the number.
Number of seconds elapsed since Counts the number of seconds since the last email was
last e-mail successfully sent
successfully sent.
Number of times the link to the
server has been detected down
260
Number of times the SMTP server could not be reached.
(Link checked every 30 minutes.)
Embedded Web Pages
NOE Properties Page
Overview
The following information describes the NOE Properties Page.
Introduction to
the NOE
Properties Page
The following figure shows the NOE Properties Page, which displays the Exec,
Kernel, Web Pages versions, and the Physical Media being used.
NOE Properties
Exec Version:
version 3.5
Kernel Version:
version 2.0
Web Pages Version:
version 3.1
Physical Media:
10/100BASE-T
Home
ConfigureNOE
NOE Diagnostics Support
Copyright © 1998 - 2003 Schneider Automation, All rights reserved.
Note: The NOE Properties Page is "information only." The fields cannot be
changed.
NOE Properties
Page Links
The following table describes the links on the NOE Properties Page.
Link
Results
Home
Returns you to the Quantum Welcome Page
Configure NOE
Provides the ability to configure and change the NOE through the
Ethernet Configuration Page
NOE Diagnostics Displays links to Ethernet Statistics and the Crash Log File Diagnostics
Support
Provides you with contact information for technical assistance, sales, and
feedback
261
Embedded Web Pages
Crash Log Diagnostics
Introduction to
the Crash Log
Diagnostics
Page
The Crash Diagnostics Page displays a crash log file when a crash has occurred,
and a status message when no crash has occurred.
Press Clear Crash Log File to clear the file.
Crash Log
Diagnostics
Links
The following table describes the links on the Crash Log Diagnostics Page.
262
Link
Results
Home
Returns you to the Quantum Welcome Page
Configure NOE
Provides the ability to configure and change the NOE through the
Ethernet Configuration Page
NOE Properties
Provides information about NOE properties
NOE Diagnostics
Displays links to Ethernet Statistics and the Crash Log File Diagnostics
Support
Provides you with contact information for technical assistance, sales, and
feedback
Embedded Web Pages
Contacting Schneider Electric Page
Overview
The following information describes the Contacting Schneider Electric Page.
Introduction to
the Contacting
Schneider
Electric Page
The following figure shows the Contacting Schneider Electric Page, which contains
information about how to obtain support for the NOE 771 xx modules.
Contacting Schneider Electric
Technical Information
Click here to go to the Schneider Electric
Automation web site.
Contact Us
Click here to contact Schneider Electric in
your country.
Home
Configure NOE
NOE Properties
NOE Diagnostics Support
Copyright © 1998 - 2003, Schneider Automation. All rights reserved.
263
Embedded Web Pages
264
Hot Standby
12
At a Glance
Introduction
The NOE 771 x0 modules offer a Hot Standby configuration available for Quantum
controllers.
Note: Hot Standby Availability and Unity
The 140 CPU 671 60 Hot Standby controller and the Hot Standby functionality will
be available only in Unity V2.0 and higher.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Overview of Modicon Quantum Hot Standby with Unity Solution for NOEs
Page
266
Hot Standby Topology
268
NOE Configuration and Hot Standby
269
IP Address Assignment
270
NOE Operating Modes and Modicon Quantum Hot Standby with Unity
272
Address Swap Times
275
Network Effects of Modicon Quantum Hot Standby with Unity Solution
276
265
Hot Standby
Overview of Modicon Quantum Hot Standby with Unity Solution for NOEs
Please Note
The Modicon Quantum Hot Standby with Unity system supports up to six NOE 771
Ethernet adapters on bus controllers.
Description of
the Hot Standby
Solution
The NOE Hot Standby allows automatic IP Address swap. Both controllers are
configured identically. One controller is the Primary NOE; the other controller, the
Secondary NOE. In case of a failure, the controllers switchover and the system
recovers.
The NOEs coordinate the swapping of IP addresses. After closing both the client
and the server connections, each NOE sends a swap UDP message to its peer
NOE. The sending NOE then waits a specified timeout (500 ms) for the peer swap
of UDP messages. Either after receiving the messages or after a timeout, the NOE
changes its IP address.
Note: NOEs must communicate with each other in order to swap IP Addresses.
Schneider Electric recommends that you connect the primary and Secondary
NOEs to the same switch because
z Communication failures between the NOEs increases the time to swap
z Connecting two NOEs to the same switch, minimizes the probability of a
communication failure
Note: Schneider Electric recommends that a switch (not a hub) is used to connect
the NOEs to each other or to the network. Schneider Electric offers switches;
please contact a local sales office for more information.
The NOE waits for either a change in the controller’s Hot Standby state or the swap
of UDP messages. Then the NOE performs one of two Hot Standby actions.
If the NOE:
1. Detects that the new Hot Standby state is either primary or standby:
The NOE changes the IP address
2. Receives a swap UDP message:
The NOE transmits a Swap UDP message and swaps the IP address
All client/server services (I/O Scanner, Global Data, Messaging, FTP, SNMP, and
HTTP) continue to run after the switchover from the old to the new Primary NOE.
Note: Failure of an NOE module is not a condition for the primary system to leave
the primary state.
266
Hot Standby
Hot Standby and
NOE Module
Functionality
The NOE 771 family provides different Ethernet services. Some services are
enabled or disabled in a Modicon Quantum Hot Standby with Unity system. The
following table shows which services are enabled and disabled.
Service
NOE 771 x1
I/O Scanning
Enabled
Global Data
Enabled
Modbus Messaging
Enabled
FTP/TFTP
Enabled
SNMP
Enabled
HTTP Server
Enabled
DHCP
Disabled
Note: Only the 140 NOE 771 01 or 140 NOE 771 11 (TCP/IP Ethernet Modules)
support a Modicon Quantum Hot Standby with Unity V2.0 system.
267
Hot Standby
Hot Standby Topology
The following diagram shows a Hot Standby system and the relationship between
the two redundant systems.Two 140 CPU 671 60 controllers are connected via a link
created with fiber optic cable. The RIOs are connected both to each other (through
the fiber optic cable) and to the RIO Drops.
R
I
O
Drop
C6
P 7
U1
Drop
N
O
E
Fiber Optic
R
I
O
T Connector
C 6
P 7
U 1
Cable
N
O
E
Ethernet Switch
Hot Standby
Interconnection
Note: The following three items are required.
1. Two identical systems
2. Identical order of modules in each rack
3. Identical software revisions
In the preceding diagram the NOEs are connected to the same switch. Connecting
to the same switch is recommended but not required. Connecting to the same switch
is recommended because the NOEs communicate with each other in order to swap
the IP address.
There are two reasons for connecting to the same switch:
z If a failure to communicate between the NOEs occurs, the time to swap
increases.
z Therefore to minimize the probability of a failure, connect the two NOEs to the
same switch.
The other requirement for the switches is that they are on the same sub network.
268
Hot Standby
NOE Configuration and Hot Standby
TCP/IP
Configuration
When an NOE goes into service the first time, the NOE attempts to get its IP Address
from a BOOTP server. If no BOOTP server is available, the NOE derives its IP
Address from its MAC address. Connecting to a BOOTP server or deriving the IP
Address from a MAC address allows you a connection to the NOE, that enables you
to download a project to the PLC.
All standard rules apply to IP addressing with the additional restriction that the IP
address cannot be greater than 253 or broadcast address minus 2. Also, no other
device can be assigned the configured IP + 1 address.
269
Hot Standby
IP Address Assignment
Configuring the
NOE
The NOE can be configured to work in conjunction with the Modicon Quantum Hot
Standby with Unity controller. Since the Primary and Secondary controllers must
have an identical configuration, the configured IP Addresses will be the same. The
NOE’s IP Address is either the configured IP Address or the configured IP Address
+1. The IP Address is determined by the current local Hot Standby state.
In the Offline state, the IP Address is determined by whether or not the other
controller is in transition to the Primary state.
Note: For a Modicon Quantum Hot Standby with Unity system, the two IP
Addresses will be consecutive.
The following table shows the IP Address assignments.
Hot Standby State
IP Address
Primary
Configured IP Address
Standby
Configured IP Address + 1
Transition from Primary to Offline
Configured IP Address, if peer controller does not
go to Primary
Transition from Standby to Offline
Configured IP Address + 1
Note: Offline - Results depend on whether or not the other controller is detected as
in transition into the primary state. If Current IP is the configured IP Address, then
change the IP Address to the configured IP Address + 1.
IP Address
Restriction
270
Note: Configuring NOE
Do not use either broadcast IP Address or broadcast IP Address - 2 to configure a
NOE.
Hot Standby
IP Address
Transparency
For continued Ethernet communication, the new Primary NOE must have the same
IP Address as the former Primary NOE. The IP Address in the Secondary NOE (an
NOE in the secondary state) is IP Address + 1.
The NOEs integrated into the Modicon Quantum Hot Standby with Unity
configuration coordinate this swapping IP Address with the management of Ethernet
services used.
Note: Do not use the address IP + 1. For a Modicon Quantum Hot Standby with
Unity system, do not use consecutive addresses of the configured IP Address. If
you configure the last IP Address (255), NOE returns diagnostic code "Bad IP
configuration".
271
Hot Standby
NOE Operating Modes and Modicon Quantum Hot Standby with Unity
The NOE Modes
The NOE modes are
z Primary Mode
The Hot Standby state is primary, and all client/server services are active.
z Secondary Mode
The Hot Standby state is standby, and all server services are active except
DHCP.
z Standalone Mode
Occurs when NOE is in a nonredundant system, or if the HE CPU module is not
present or is not healthy.
z Offline Mode
CPU is stopped.
CPU module is in Offline mode.
The Modicon Quantum Hot Standby with Unity and the NOE operating modes are
synchronized by the conditions described in the following table.
HE CPU Module Status
HSBY State
NOE Operating Mode
Present and Healthy
Primary
Primary
Present and Healthy
Standby
Secondary
Present and Healthy
Offline
Offline
Present and Healthy
Unassigned
Standalone
Not present or unhealthy
N/A
Standalone
Any one of four events will affect the NOE operating mode. These four events occur
when the NOE is powered-up, when an NOE executes a Hot Standby switchover,
when an NOE goes to offline mode, or when a new application is downloaded to the
NOE.
272
Hot Standby
Power-Up and IP
Address
Assignment
An NOE obtains its IP Address assignment at power-up as follows:
If the HSBY state is ...
Then the IP Address assigned is ...
Unassigned
Configured IP Address
Primary
Configured IP Address
Secondary
Configured IP Address + 1
Unassigned to Offline
See the Offline Mode at Power-up Sequence table following
If two NOEs power-up simultaneously, a "resolution algorithm" determines the
Primary NOE, and after determining the Primary NOE, the "resolution algorithm"
assigns the configured IP Address to the Primary NOE and then assigns the
configured IP Address + 1 to the Secondary NOE.
Offline Mode at Power-up Sequence table:
Offline Mode at Power-up Sequence
Result
Controller A powers-up before controller B
z
z
IP Address of controller A is configured IP
Address
IP Address of controller B is the configured
IP Address + 1
Both controller A and controller B power-up The resolution algorithm will assign controller A
a the same time
the configured IP address and will assign
controller B the configured IP address + 1.
The NOE performs a "duplicate IP" test by issuing an ARP request to the configured
IP Address. If a response is received within 3 seconds, the IP Address remains at
the Default IP and blinks a diagnostic code.
If no IP configuration exists, the NOE remains in standalone mode, and the IP
Address must be obtained from either a BOOTP server or from a MAC address.
Power-Up and
Ethernet
Services
The following table shows how the status of an NOE service is affected by the
Modicon Quantum Hot Standby with Unity HSBY state.
HSBY State
Status of NOE Services
Client Services
Client/Server
Services
Server Services
I/O Scanner Global Data Modbus Messaging
FTP
SNMP HTTP
Unassigned
Run
Run
Run
Run
Run
Run
Primary
Run
Run
Run
Run
Run
Run
Secondary
Stop
Stop
Run
Run
Run
Run
Offline
Stop
Stop
Run
Run
Run
Run
273
Hot Standby
Hot Standby
Switchover
The following steps describe how NOEs coordinate the Hot Standby switchover.
Step
1
NOE A (installed in a HSBY rack) detects that its local controller changed from
Primary to Offline.
2
NOE A changes its HSBY state from Primary to Offline with the same Ethernet
services running, starts its watch-dog timer (with 500 ms timeout setting), and
expects from its peer NOE a UDP request to swap the IP Address.
3
NOE B (installed in peer HSBY rack) detects that its local controller changed
state from Secondary to Primary.
4
NOE B stops all Ethernet services, sends a UDP request to its peer NOE (NOE
A) for the synchronization of the IP Address swap, starts its watch-dog timer
(with 500 ms timeout setting), and then waits for an UDP response from its peer
NOE.
5
Once NOE A receives the UDP request from NOE B (or after its watch-dog timer
times out), it stops all Ethernet services, sends a UDP response to NOE B (no
UDP response is sent to NOE B for watch-dog timeout case), swaps IP Address
as Secondary, and starts Secondary services.
6
As soon as NOE B receives the UDP response from NOE A (or after its watchdog timer times out), it swaps IP Addresses and starts Ethernet services as
Primary.
7
After NOE A senses that its local controller changes state from Offline to
Standby, it changes to Secondary accordingly.
8
The Secondary NOE now becomes the Primary NOE.
9
Primary NOE opens all client connections and listens for all server connections
and re-establishes those connections.
10
Going to Offline
274
Action
Simultaneously, Secondary NOE listens for all server connections and reestablishes those connections.
When either the CPU stops or the Hot Standby state goes to offline mode, two
events occur:
1. NOE mode goes to Offline
2. NOE uses the IP Address of the present configuration
IP Address Assignment and Going Offline
HSBY State
IP Address Assigned Is ...
Primary to Offline
Configured IP Address, if other controller does not go to
Primary
Standby to Offline
Configured IP Address + 1
Hot Standby
Address Swap Times
Description
The following table details what the "time for an Address swap" comprises, such as
the time to close connections, time to swap IP addresses, or time to establish
connections.
The following table shows the swap time for each of the Ethernet services.
Service
Typical Swap Time
Maximum Swap Time
Swap IP Addresses
6 ms
500 ms
I/O Scanning
1 initial cycle of I/O Scanning 500 ms + 1 initial cycle of I/O
scanning
Global Data
For swap times, please see
the 840USE11600, Quantum
NOE 771 xx Ethernet
Modules User Guide
500 ms + 1 CPU scan
Client Messaging
1 CPU scan
500 ms + 1 CPU scan
Server Messaging
1 CPU scan + the time of the
client reestablishment
connection
500 ms + the time of the client
reestablishment connection
FTP/TFTP Server
The time of the client
reestablishment connection
500 ms + the time of the client
reestablishment connection
SNMP
1 CPU scan
500 ms + 1 CPU scan
HTTP Server
The time of the client
reestablishment connection
500 ms + the time of the client
reestablishment connection
275
Hot Standby
Network Effects of Modicon Quantum Hot Standby with Unity Solution
Overview
The Modicon Quantum Hot Standby with Unity solution is a powerful feature of
NOEs, a feature that increases the reliability of your installation. Hot Standby uses
a network, and using the Hot Standby feature over a network can affect the behavior
of
z Browsers
z Remote and Local clients
z I/O Scanning service
z Global Data service
z FTP/TFTP server
The following are factors you may encounter while using the Modicon Quantum Hot
Standby with Unity solution.
Browsers
Note: In Modicon Quantum Hot Standby with Unity configuration the NOE’s I/O
scanner is enabled.
If a browser requests a page and during the process of downloading that page an IP
Address swap occurs, the browser will either hang or time out. Click the Refresh or
Reload button.
Remote Clients
Hot Standby swaps affect remote clients.
An NOE will reset under the following conditions:
z Remote Connection Request during Hot Standby Swap
If a remote client establishes a TCP/IP connection during a Hot Standby swap,
the server closes the connection using a TCP/IP reset.
z Hot Standby Swap during Remote Connection Request
If a remote client makes a connection request and a Hot Standby swap occurs
during the connection request, the sever rejects the TCP/IP connection by
sending a reset.
z Outstanding Requests
If there is an outstanding request, the NOE will not respond to the request, but
the NOE will reset the connection.
The NOE will do a Modbus logout if any connection has logged in.
Local Clients
During a swap, the NOE will reset all client connections using a TCP/IP reset.
276
Hot Standby
I/O Scanning
Service
The I/O Scanning provides the repetitive exchange of data with remote TCP/IP
nodes I/O devices. While the PLC is running the Primary NOE sends Modbus Read/
Write, read or write request to remote I/O devices, and transfer data to and from the
PLC memory. In the secondary controller, the I/O scanning service is stopped.
When the Hot Standby swap occurs, the Primary NOE closes all connections with I/
O devices by sending a TCP/IP reset. The I/O scanning service in this NOE is
standby.
After the swap, the new Primary NOE re-establishes the connection with each I/O
devices. It restarts the repetitive exchange of data with these re-connections.
The NOE 771 01 and 11 provides the I/O scanning feature. Configure using either
z Unity Pro software
z Internal I/O Scanner Web page
Using either method, the configuration and transfer of data between network
addresses can be done without using the MSTR/IEC function block.
Note: I/O SCANNING AND SWITCHOVER WITH CRITICAL APPLICATIONS
Account for the following Ethernet I/O scanning considerations during a
switchover.
z If MSTR/IEC function block is used for TCP/IP, only some of the Op Code will
be used. Therefore, the block will not complete its transaction and returns error
code 0x8000.
z While the NOE is in the process of performing the transaction, a new MSTR/IEC
function block may become active.
z The output states of the scanned I/Os will follow the state defined in the last
value option configured in the I/O scanning table of the NOE module (in Unity
Pro software).
These two states are either
1. set to 0
2. Hold last
With the above considerations, Schneider Electric recommends using switchover
with Ethernet I/O scanning for less critical applications.
277
Hot Standby
Global Data
(Publish/
Subscribe)
Service
The Hot Standby NOE is one station within a distribution group. Distribution groups
exchange application variables. Exchanging application variables allows the system
to coordinate all the stations in the distribution group. Every station publishes local
application variable in a distribution group for all other stations and can subscribe to
remote application variables independent of the location of the producer.
The communication port has only one multicast address.
In this network service, the Modicon Quantum Hot Standby with Unity controllers are
viewed like only one station. The Primary NOE publishes the Hot Standby
application variables and receives the subscription variables. The Secondary NOE
global data service is in a stopped state.
When the Hot Standby swap occurs, the Primary NOE stops the Global Data
service. The NOE does not publish the local variable during a swap. And after the
swap, the new Primary NOE starts to publish application variables and to receive the
subscription variables.
FTP/TFTP Server
The File Transfer Protocol/Trivial File Transfer Protocol (FTP/TFTP) server is
available as soon as the module receives an IP address. Any FTP/TFTP client can
logon to the module. Access requires the correct user name and password. Modicon
Quantum Hot Standby with Unity allows only one active FTP/TFTP client session
per NOE module.
When the Hot Standby swap occurs, the Primary and Secondary NOEs close the
FTP/TFTP connection. If a user sends an FTP/TFTP request during the swap, the
communication is closed.
Whenever you re-open communication, you must re-enter a user name and a
password.
278
Appendices
At a Glance
Introduction
The appendices provide supplementary reference information for the Quantum 140
NOE 771 •• series of modules and the 140 NWM 100 00 module.
What's in this
Appendix?
The appendix contains the following chapters:
Chapter
A
Chapter Name
Page
Maintenance
281
B
Specifications
293
C
Quantum Ethernet TCP/IP Modbus Application Protocol
297
279
Appendices
280
Maintenance
A
At a Glance
Introduction
This chapter details information about system maintenance including accessing and
clearing the crash log and downloading the new NOE exec.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Responding to Errors
Page
282
Reading and Clearing the Crash Log
287
Downloading a New NOE Exec
288
Downloading a New NOE Exec via FTP
289
Downloading a New NOE Kernel
291
281
Maintenance
Responding to Errors
Overview
The following information describes how to respond to errors on the NOE 771 x0.
Detecting Errors
When faults occur, the NOE 771 xx LED display can help you determine what went
wrong. The following figure shows the pattern that the LEDs should display during
normal operation.
140
NOE 771 xx
ETHERNET TCP/IP
Active
Ready
Run
Link
The Run indicator will be solid. The Coll LED may flash, indicating that collisions are
occurring on the Ethernet network. Such collisions are normal.
If a fault occurs, the normal LEDs may be extinguished or other indicators may light.
This section will discuss errors reported by the Active, Ready, Coll, Link, Kernel,
Appl and Fault indicators.
For each type of error, try the suggested remedies in the order given. If no remedy
suggested here overcomes the error, call your local service representative or call
Schneider Electric customer service at 1-800-468-5342 for further directions.
282
Maintenance
Procedure for
Responding to
an Active LED
Error Indicator
Procedure for
Responding to a
Ready LED Error
Indicator
Procedure for
Responding to a
Link LED Error
Indicator
If the Active LED fails to light, the NOE 771 00 module is not communicating with the
backplane. The following procedure describes the steps to perform to respond to an
Active LED error.
Step
Action
1
Make sure the NOE 771 module and the controller are installed properly.
2
Verify that the controller is working; if it is not, replace it.
3
If neither the new controller nor the NOE 771 module functions, replace the
backplane.
4
Make sure that no more than two network option modules -- including NOE,
NWM, NOM, NOP, and CRP 811 modules -- have been installed in the
backplane with a 140 CPU 311 10; not more than six network option modules
with a 140 CPU 434 12A or 140 CPU 534 14A.
5
Check the version of the controller executive. You must have version 2.0 or
greater to support the Ethernet module. Earlier versions do not recognize the
module.
6
If steps 4 and 5 above check out ok, replace the NOE 771 module.
If the Ready LED fails to light, the NOE 771 module has failed internal diagnostic
tests. The following procedure describes the steps to perform.
Step
Action
1
Make sure that power has been applied to the backplane.
2
If step 1 checks out ok, replace the NOE 771 module.
If the Link LED fails to light, the NOE 771 module is not communicating with the
Ethernet hub/switch. The following procedure describes the steps to perform to
respond to a Link LED error.
Step
Action
1
Make sure that the cable has been installed correctly and the module is
functioning properly.
2
Verify that the hub/switch is working properly.
3
If steps 1 and 2 check ok, replace the NOE 771 module.
283
Maintenance
Kernel LED Error
Fault LED
The following table describes the Kernel LED errors that may occur and how to
respond to them.
If
Then
The Ready LED is on and the Kernel LED
is flashing
the module has detected an invalid software
image.
The Ready LED is on and the Kernel LED
is shining steadily,
an attempt to download a software image has
failed and the module is in kernel mode.
Either of the above conditions exists.
download a new NOE Exec see .
The Fault LED will flash briefly following an error as the module attempts to recover.
The following figure shows the Fault LED.
140
NOE 771 xx
ETHERNET TCP/IP
Active
Fault
Link
Appl
284
Maintenance
Collision LED
Error
If the twisted pair cable has not been connected properly, the Coll LED will shine
steadily and the Link LED will be extinguished. (This condition does not occur with
fiber optic modules.)
The following figure shows the Collision LED.
140
NOE 771 xx
ETHERNET TCP/IP
Active
Ready
Coll
Link
Procedure for
Responding to a
Collision LED
Error
If the Collision LED fails to light, use the following procedure.
Step
Action
1
Make sure that the cable has been installed and is working properly.
2
Verify that the Ethernet Hub/Switch is working properly.
285
Maintenance
Collision LED
Normal
Condition
If the Coll LED is flashing, the module is reporting collisions on the Ethernet
network. While such collisions are normal, the frequency of the flashes is an
indication of the volume of traffic on the network. The flashes may be so frequent
that the LED appears to be shining steadily. Heavy traffic will slow communications.
If response time is important to your application, you should consider segmenting
your network to reduce the frequency of collisions.
The following figure shows the Collision LED under normal conditions.
140
NOE 771 xx
ETHERNET TCP/IP
Active
Ready
Run
Link
Run LED
Coll
The following table describes the action to be taken if the Run LED is flashing. The
action depends on the number of flashes in sequence.
# of Flashes in Sequence
Application LED
286
Action
Three
Check Ethernet connection.
Four
Change IP address
Five
Provide IP address
Six
Connect using default IP address and configure
Seven
Download NOE Executive
If the module crashes, it will note the reason in a log. If the module is able to recover,
the Appl LED will light, indicating that an entry has been made in the crash log. To
learn how to read and clear the crash log, refer to Reading and Clearing the Crash
Log, p. 287.
Maintenance
Reading and Clearing the Crash Log
Overview
The following information describes the crash log.
Introduction
The crash log provides you with the ability to capture conditions that lead to an
anomalous condition. By providing the crash log to Schneider Electric technical
support, you can facilitate their assistance in resolving your problems.
Note: The crash log is provided with the understanding that, with a complex
product in thousands of customer applications, there may be conditions that
require advance diagnostics. The crash log is one of the tools used to solve
complex problems.
The Crash Log
If the Appl indicator is on, entries have been made in the crash log. The log may
hold up to 64K of entries.
Reading the
Crash Log
The crash log can be read from the Embedded Web Pages (see Embedded Web
Pages, p. 217) or via FTP.
Procedure for
Reading the
Crash Log via
FTP
The following procedure describes the steps to perform to access the crash log via
FTP.
Step
Action
1
Log into the module’s FTP Server
2
Change the directory to wwwroot/conf/diag
3
Perform an FTP to get the crash log file: get crash.log
Clearing the
Crash Log
The crash log can be cleared from the Embedded Web Pages (see Embedded Web
Pages, p. 217) or via FTP.
Procedure for
Clearing the
Crash Log via
FTP
The following procedure describes the steps to perform to access the crash log via
FTP.
Step
Action
1
Log into the module’s FTP Server.
2
Change the directory to wwwroot/conf/diag.
3
Perform an FTP to delete the crash log file: rm crash.log
287
Maintenance
Downloading a New NOE Exec
Introduction
288
The following tools can be used to download a new NOE Exec:
z Schneider Electric programming packages (see corresponding manuals)
z FTP
Maintenance
Downloading a New NOE Exec via FTP
Exec Version
Please check the current NOE Exec file version on the NOE Properties Web page.
Follow these links:| Web Server | Diagnostics and Online Configuration | NOE
Properties |
Procedure
The following procedure describes the steps to use to download a new NOE Exec
via FTP. An example follows the procedure.
Step
Action
1
At the DOS prompt, type FTP, followed by the IP Address and press Enter.
2
At the User prompt, type: USER and press Enter.
3
At the password prompt, enter your FTP Password and press Enter.
4
At the FTP prompt, type cd wwwroot/conf/exec and press Enter.
5
At the FTP prompt, type put and press Enter.
Note: Pay attention that the NOE771xx.bin has to be to the local path on your PC
(default path: c:\).
6
At the local file prompt, type NOE771xx.bin and press Enter.
7
At the remote file prompt, type NOE771xx.bin and press Enter.
8
After the transfer is complete you must reboot the NOE to allow the new EXEC to
become operational.
Note: The file name is case sensitive and must be entered with the name in
uppercase and the extenion in lowercase as shown in the figure below.
For example: NOE771xx.bin
289
Maintenance
Sample FTP
Session
The following FTP session was used to download an NOE Exec.
Command Prompt - ftp 205.217.193.173
C:\noe77100>ftp 205.217.193.173
331 Password required
Password:
230 User logged in
ftp> cd wwwroot/conf/exec
250 Changed directory to “/FLASH0/wwwroot/conf/exec”
ftp> put
(local-file) NOE77100.bin
(remote-file) NOE77100.bin
200 Port set okay
150 Opening BINARY mode data connection
226 Transfer complete
485376 bytes sent in 3.06 seconds (158.41 Kbytes/sec)
ftp> dir
200 Port set okay
150 Opening BINARY mode data connection
-rwx---A-- 1 user
2 kerVer
-rwx---A-- 1 user
485376 NOE77100.bin
226 Transfer complete
86 bytes received in 0.01 seconds (8.60 Kbytes/sec)
ftp> _
Connected to 205.217.193.173.
220 VxWorks FTP server (VxWorks 5.3.1) ready.
User (205.217.193.173:(none)): USER
Note: The NOE Kernel can not be downloaded via FTP.
Reboot
Information after
FTP
290
Note: After downloading by FTP, reboot the module.
Perform a download or a reboot when your system can tolerate these actions.
Maintenance
Downloading a New NOE Kernel
Procedure
The NOE Executive (Exec) adds a new feature that allows updating of the low level
Kernel within the NOE 771 xx's firmware. For the proper installation of new kernel
firmware, use the following procedure.
Step
Action
1
Check the current version of the NOE's Executive firmware (Exec file).
2
If the Exec is not the appropriate version, the Exec must be updated before
updating the Kernel.
3
Use the EXECLoader to load the latest version of the EXEC.
4
After loading the new Exec and before loading the Kernel, make sure to cycle
power to the NOE.
5
Load the Kernel using the EXECLoader.
6
After the transfer displays as Successful, the NOE needs approximately 1
minute to burn the new Kernel into the NOE's FLASH.
7
The NOE goes go through a reboot sequence.
Kernel Version
Note: The NOE Kernel can not be downloaded via FTP.
Please check the current NOE Kernel version on the NOE Properties Web page.
Follow these links:| Web Server | Diagnostics and Online Configuration | NOE
Properties |
Note: NOE Operation
Failure to perform the preceding update procedure will render the NOE inoperable.
291
Maintenance
292
Specifications
B
Specifications
Overview
The following information describes the main specifications for the Quantum 140
NOE 771 xx and 140 NWM 100 00 Ethernet Module.
293
Specifications
140 NOE 771 ••
Specification
Table
The main specifications for the Quantum 140 NOE 771 xx Ethernet Module are
described in the following table
Communication Ports
One auto-sensing 10/100Base-T shielded twisted pair (RJ-45
connector) port and one 100Base-FX (MT-RJ connector) port. Both
ports transmit and receive Modbus commands encapsulated in
TCP/IP protocol
Bus Current Required
750 mA
Power Dissipation
3.8 W
Fuse
None
Programming Software
Type and version
Concept, Ver. 2.2, or higher
Unity Pro, Ver. 1.0, or higher
Modlink, Ver. 2.0, or higher
Modsoft, Ver. 2.6, or higher
ProWORX NxT, Ver. 2.1, or higher
Firmware
CPU Type and version
Quantum Executive, Ver. 2.0, or higher
NOE Upgradeable
Field Upgradeable via FTP or Programming Panel.
Operating Conditions
Temperature
0 to +60° C
Humidity
0 to 95% Rh non condensing @ 60° C
Altitude
15,000 ft (4500 m)
Vibration
10-57 Hz @ 0.0075 mm d.a
57-150 Hz @ 1 g
Storage Conditions
140 NWM 100 00
Specification
Table
294
Temperature
-40 to +85°C
Humidity
0 to 95% Rh non condensing @ 60°C
Free Fall
1 m unpackaged
Shock
3 shocks / axis, 15 g, 11 ms
The main specifications for the Quantum 140 NWM 100 00 Ethernet Module are
described in the following table
Communication Ports
One auto-sensing 10/100Base-T shielded twisted pair (RJ-45
connector) port and one 100Base-FX (MT-RJ connector) port. Both
ports transmit and receive Modbus commands encapsulated in
TCP/IP protocol
Specifications
Bus Current Required
900 mA
Power Dissipation
4.5 W
Fuse
None
Programming Software
Type and version
Concept, Ver. 2.6, or higher
Unity Pro, Ver. 1.0, or higher
Firmware
CPU Type and version Quantum Executive, Ver. 2.6, or higher
NOE Upgradeable
Field Upgradeable via FTP or Programming Panel.
Operating Conditions
Temperature
0 to +60° C
Humidity
0 to 95% Rh non condensing @ 60° C
Altitude
15,000 ft (4500 m)
Vibration
10-57 Hz @ 0.0075 mm d.a
57-150 Hz @ 1 g
Storage Conditions
Temperature
-40 to +85°C
Humidity
0 to 95% Rh non condensing @ 60°C
Free Fall
1 m unpackaged
Shock
3 shocks / axis, 15 g, 11 ms
Immunity
International Standard
ISO/IEC 802-3 ANSI/IEEE Std 802.3 2000 Edition
US Standard
UL508, CEI 1131-2 for Immunity and 50081-2 for Emissions.
European Standard
CSA C22.2 / 142
Canadian Standard
Conformity to FCC-B for Emission (50082-1
CE Marketing
Conformance to Marine Standards for the Principal European
Organizations
V, DNV, GL, LROS, RINA
IEC 61131-2, EN66631-2
Agency Approvals
UL 508, 94 Specifications
CSA 22.2-142
IEC 1131
CE
Factory Mutual Class 1 Division 2
Maritime Certifications
295
Specifications
296
Quantum Ethernet TCP/IP Modbus
Application Protocol
C
At a Glance
Introduction
This chapter describes the Quantum Ethernet TCP/IP Modbus Application Protocol.
What's in this
Chapter?
This chapter contains the following topics:
Topic
Page
Overview
298
Modbus Application Protocol PDU
299
Modbus Application Protocol Service Classes
301
Modbus Application Protocol PDU Analysis
302
TCP/IP Specific Issues
304
Reference Documents
305
297
Ethernet TCP/IP Modbus Application Protocol
Overview
Introduction
298
The following information describes the Modbus Application Protocol (MBAP).
The Modbus Application Protocol (MBAP) is a layer-7 protocol providing peer-topeer communication between programmable logic controllers (PLCs) and other
host-based nodes on a LAN. Collectively, these nodes implement all or part of a
control application used for industrial automation applications in the automotive, tire
and rubber, food and beverage, and utilities industries, to name a few.
Modbus protocol transactions are typical request-response message pairs. Modbus
requests contain function codes representing several classes of service including
data access, online programming, and program download and upload classes.
Modbus responses can be ACKs with and without data, or NACKs with error
information.
The Modbus Application Protocol can be transmitted over any communication
system that supports messaging services. However, the current Quantum
implementation transports Modbus Application Protocol PDUs over TCP/IP. Both
Ethernet II and IEEE 802.3 framing are accommodated, although Ethernet II framing
is the default.
For more information, consult the Modbus Protocol Reference Guide.
Ethernet TCP/IP Modbus Application Protocol
Modbus Application Protocol PDU
Overview
The following information describes the structure and content of the Modbus
Application Protocol PDU.
Description
The Modbus Application Protocol PDU, mbap_pdu, is received at TCP port number
502. The current maximum size of the mbap_pdu for this class of services is 256
bytes. The structure and content of the mbap_pdu is defined to be:
mbap_pdu::={inv_id[2], proto_id[2], len[2],dst_idx[1],
data=mb_pdu}
The header is seven bytes long and includes the fields listed in the following table:
Field
Description
inv_id
[2 bytes] invocation id used for transaction pairing
proto_id
[2 bytes] used for intra-system multiplexing, default is 0 for Modbus services
len
[2 bytes] the len field is a byte count of the remaining fields, and it includes the
dst_id and data fields
The remainder of the pdu includes two fields:
Field
Description
dst_idx
[1 byte] destination index is used for intra-system routing of packets (currently
not implemented)
data
[n bytes] this is the service portion of the Modbus pdu, mb_pdu, and it is defined
below
The service portion of the Modbus Application Protocol, called mb_pdu, contains
two fields:
mb_pdu::={func_code[1], data[n]}
The following table describes the fields in mb_pdu.:
Field
Description
func_code{1 byte Modbus function code
data
[n bytes] this field is function code dependent and usually contains
information such as variable references, variable counts, and data offsets
The size and content of the data field are dependent on the value of the function
code.
299
Ethernet TCP/IP Modbus Application Protocol
Example
Here are the values for a sample mbap_pdu for reading a register:
00 01 00 00 00 06 01 03 00 00 00 01
The following table shows the structure and content for this example:
inv_id
00 01
proto_id
300
00 00
len
00 00
dst_idx
01
func_code
03
data
00 00 00 01
Ethernet TCP/IP Modbus Application Protocol
Modbus Application Protocol Service Classes
Introduction
There are several classes of service that are part of the Modbus Application
Protocol. Each of these classes is described below.
Data Access
Read/write both discrete and analog data values from PLC register files.
Online
Programming
Services make relatively minor alterations to ladder logic programs with a highly
controlled introduction of these changes into the executing program.
Image Download/
Upload
Image download services support the downloading of a ladder logic control program
to the PLC. Image upload services support the uploading of a ladder logic control
program from a PLC to PC host for archival/backup purposes.
Configuration
Configuration services allow the user to define parameter values which affect the
PIC’s register files, I/O map, communication port configuration and scan attributes,
to name a few.
Device
Execution State
Control
The class of service allows the user to start/stop the PLC scan execution. These
services require the user to be in an application login context which is obtained
through other Modbus services.
301
Ethernet TCP/IP Modbus Application Protocol
Modbus Application Protocol PDU Analysis
Oveview
The following information provides an analysis of the Modbus Application Protocol.
Analysis
The Modbus Application Protocol PDU is transmitted over a TCP/IP Ethernet stack.
Both Ethernet II and IEEE 802.3 framing will be accommodated. Ethernet II framing
is the default.
. . .
from the wire in for IEEE 802.3 framing
. . .
. . . is IEEE 802.3 framing if length <=1500 . . .802.3_pdu
::= {dst_addr[6], src_addr[6], length[2], data=802.2_pdu}*an
IEEE 802.3 PDU has a maxFrameSize of 1518 octets
*an IEEE 802.3 PDU has a minFrameSize of 64 octets802.2_pdu :
{dsap[1], ssap[1], frm_cntrl[1], snap_hdr[5], data=ip_pdu}
*the snap_hdr is associated with a "well-known" 802.2 sap
snap_hdr
::={org_code[3], ethertype[2] }
*the snap hdr (sub network access protocol) allows the older
style
Ethernet protocols to run on the newer IEEE 802.2 interface.
The
ethertype parameter indicates the service, ex. ip or arp. IP
has a value
0x800.. . .
from the wire in for Ethernet II framing
. . .
. . . is Ethernet II framing if length >1500 . . .802.3_pdu
::= {dst_addr[6], src_addr[6], length[2], data=ip_pdu}. . .
the common part of the packet begins here
. . .ip_pdu ::=
{ip_hdr[20], data=tcp_pdu}tcp_pdu ::= {tcp_hdr[24],
data=appl_pdu=mbap_pdu}
The mbap_pdu is the Modbus Application Protocol whose messages are received
at a well-known port. The current maximum size of the mbap_pdu for this class of
services in 256 bytes.
302
Ethernet TCP/IP Modbus Application Protocol
Structure and
Content
The structure and content of the mbap_pdu is defined to be:
mbap_pdu ::={ inv_id[2], proto_id[2], len[2], dst_idx[1],
data=mb_pdu }The header is 7 bytes long, and includes the
following fields:
inv_id[2 bytes] invocation id used for transaction pairing
proto_id[2 bytes] used for intra-system multiplexing,default
is 0 for Modbus
serviceslen[2 bytes] the len field is a byte count of the
remaining fields and
includes the dst_id and data fields.
The remainder of the pdu includes two fields:
dst_idx[1 byte] destination index is used for intra-system
routing of
packets. (currently not implemented)data[n bytes] this is the
service portion of the Modbus pdu, mb_pdu, and is
defined below
The service portion of the Modbus Application Protocol, called mb_pdu, contains 2
fields:
mb_pdu ::= { func_code[1], data[n] }
func_code[1 byte] MB function codedata[n bytes] this field is
function code dependent and usually contains
information such as variable references, variable counts, and
data offsets.
The size and content of the data field are dependent on the value of the function
code.
303
Ethernet TCP/IP Modbus Application Protocol
TCP/IP Specific Issues
Overview
The following information describes some TCP/IP specific issues.
Broadcast/
Multicast
Although broadcast and/or multicast are supported by both IP network address and
IEEE 802.3 MAC address, the Modbus Application Protocol does not support either
broadcast or multicast at the application layer.
Schneider Electric’s Quantum PLCs use broadcast addressing because they use
ARP as the means of locating the destination node. The client interface to the
Modbus Application Protocol service on the PLC, the MSTR block, requires the user
to provide the destination IP address. Also the embedded stack does use a preconfigured default gateway IP address in the case where ARP does not succeed.
TCP Port Number
Schneider Electric has obtained a well-known system port from an Internet
Authority. Schneider Electric’s well-known system port number is 502. The Internet
Authority assigned the system port number 502 to asa-appl-proto with Dennis Dubé
as the company point of contact.
This port number allows Schneider Electric to transport various application protocols
over with TCP or UDP. The particular protocol is indicated by the value of the
proto_id parameter in the mbap_pdu. Currently the only assignment is 0 meaning
Modbus Application Protocol.
304
Ethernet TCP/IP Modbus Application Protocol
Reference Documents
Overview
The following information provides a list of reference documents that you may find
helpful.
Introduction
Following is a list of related documentation.
z ANSI/IEEE Std 802.3-1985, ISO DIS 8802/3, ISBN - 0-471-82749-5, May 1988
z ANSI/IEEE Std 802.2-1985, ISO DIS 8802/2, ISBN 0-471-82748-7, Feb 1988
z RFC793, TCP (Transmission Control Protocol) DARPA Internet Program
Protocol Specification, Sep 1981
z RFC 791, IP (Internet Protocol) DARPA Internet Protocol Specification, Sep
1981
z RFC826, An Ethernet Address Resolution Protocol (ARP), David Plummer, NIC
Sep 1982
z RFC1042, A Standard for the Transmission of IP Datagrams over IEEE 802.2
Networks, Postel & Reynolds, ISI, Feb 1988
z RFC 792, ICMP (Internet Control Message Protocol) DARPA Internet C Control
Message Protocol Specification, Jon Postel, Sep 1981
z RFC951, BOOTSTRAP PROTOCOL (BOOTP), Bill Croft and John Gilmore,
September 1985
z RFC783, The Trivial File Transfer Protocol (TFTP) rev 2, K.R. Solons MIT, June
1981
305
Ethernet TCP/IP Modbus Application Protocol
306
Glossary
A
ACK
Acknowledgement
address
On a network, the identification of a station. In a frame, a grouping of bits that
identifies the frame’s source or destination.
API
Application Program Interface. The specification of functions and data used by one
program module to access another; the programming interface that corresponds to
the boundary between protocol layers.
ARP
Address Resolution Protocol. A network layer protocol used to determine the
physical address which corresponds to the IP address for a host on the network.
ARP is a sub-protocol which operates under TCP/IP.
ASN.1
Abstract Syntax Notation. Grammar used to define a protocol (OSI scope)
B
Backplane
A metal plate with a bus-bar and couplers. Use the backplane to attach a module
and make a PLC bus connection.
BOOTP
BOOTstrap Protocol. A protocol used at power-up in order to get an IP address
which is provided by a BOOTP server and is based on the module’s MAC address.
bps
Bits per second.
307
Glossary
bridge
A device that connects two or more physical networks which use the same protocol.
Bridges read frames and decide whether to transmit or block them based on their
destination address.
BSP
Board Support Package. A software package that maps a specific real-time
operating system (RTOS0 onto a specific hardware.
C
client
A computer process requesting service from other computer processes.
Cyclic Data
Exchange
Provides data transfer between two or more NOE 771 xx controllers on a TCP/IP
network.
D
default gateway
The IP address of the network or host to which all packets addressed to an unknown
network or host are sent. The default gateway is typically a router or other device.
DHCP
Dynamic Host Configuration Protocol. An improved version of BOOTP.
DHCP Client
Host on the network obtaining its configuration from a DHCP Server.
DHCP Server
Server providing configuration parameters to a DHCP Client.
DNS
Domain Name System. A protocol within TCP/IP used to find IP addresses based
on host names
F
FactoryCast
An embedded Web server which the user customizes, permitting user access to
controller diagnostics and Ethernet configuration.
field
A logical grouping of contiguous bits that convey one kind of information, such as
the start or end of a message, an address, data, or an error check.
308
Glossary
firewall
A gateway that controls access to a network or an application.
frame
A group of bits which form a discrete block of information. Frames contain network
control information or data. The size and composition of a frame is determined by
the network technology being used.
framing types
Two common framing types are Ethernet II and IEEE 802.3.
FTP
File Transfer Protocol. The protocol (over TCP) used to read or write a file into a
remote station (the FTP server side).
G
gateway
A device which connects networks with dissimilar network architectures and which
operates at the Application Layer. This term may refer to a router.
Global Data
(Publish /
Subscribe)
Service of inter PLC synchronization (shared databases).
H
half duplex
(HDX) A method of data transmission capable of communication in two directions,
but only one direction at a time.
host
A node on a network.
hostname
A domain name given to a specific computer on a network and used to address that
computer.
HTTP
A domain name given to a specific computer on a network and used to address that
computer.
hub
A device which connects a series of flexible and centralized modules to create a
network.
309
Glossary
I
I/O Drop
One or two (depending on the system type) Remote I/O Channels consisting of a
fixed number of I/O points.
I/O Map
An area in the controller configuration memory used to map input and output points.
Previously called traffic cop.
I/O Scan
A procedure the processor follows to monitor inputs and control outputs.
I/O Scan List
A configuration table which identifies the targets with which repetitive
communication is authorized.
I/O scanner
Software component which is in charge of scanning Ethernet based Momentum IO
in order to get inputs and set outputs.
ICMP
Internet Control Message Protocol. A protocol within TCP/IP used to report errors in
datagram transmission.
Internet
The global interconnection of TCP/IP based computer communication networks.
IP
Internet Protocol. A common network layer protocol. IP is most often used with TCP.
IP Address
Internet Protocol Address. A 32-bit address assigned to hosts using TCP/IP.
L
layer
In the OSI model, a portion of the structure of a device which provides defined
services for the transfer of information.
Legacy
In the sense of network communication: Existing Components (PLC products etc.)
that do not provide special (hardware) support for Control Intranet.
310
Glossary
M
MAC Address
Media Access Control address. The hardware address of a device. A MAC address
is assigned to an Ethernet TCP/IP module in the factory.
MBAP
Modbus Application Protocol
MIB
Management Information Base. Database that holds the configuration of a SNMP
enabled device.
MODBUS
A communication system that links Modicon controllers with intelligent terminals and
computers over common carrier or dedicated lines
MSTR
A special master instruction which uses ladder logic to read and write controller
information.
N
NACK
Negative acknowledgment indicating an error.
NDDS
Network Data Delivery Services.
network
Interconnected devices sharing a common data path and protocol for
communication.
node
An addressable device on a communications network.
NTP
Network Time Protocol. A protocol used to synchronize the time of a client or server
to the time of another server or referenced source like a satellite receiver.
O
OIT / OID
Object Information True / Object ID (identify OIT) Contain databases managing
SNMP (MIBs)
311
Glossary
OSI model
Open System Interconnection model. A reference standard describing the required
performance of devices for data communication. Produced by the International
Standards Organization.
P
packet
The unit of data sent across a network.
Peer Cop
Software that allows you to configure data blocks to be transferred between
controllers on a Modbus Plus network.
PING
Packet Internet Groper. A program used to test whether a destination on a network
can be reached.
PLC
Programmable Logic Controller
port
An access point for data entry or exit within a host using TCP services.
protocol
Describes message formats and a set of rules used by two or more devices to
communicate using those formats.
R
repeater
A device that connects two sections of a network and conveys signals between them
without making routing decisions or filtering packets.
RFC
Request For Comment. Paper identified by a number in Internet world. They define
the state of art regarding Internet protocols (ruled by IETF = Internet Engineering
Task Force) http://www.ietf.org
router
A device that connects two or more sections of a network and allows information to
flow between them. A router examines every packet it receives and decides whether
to block the packet from the rest of the network or transmit it. The router will attempt
to send the packet through the network by the most efficient path.
312
Glossary
S
server
Provides services to clients. This term may also refer to the computer on which the
service is based.
SMTP
Simple Mail Transfer Protocol. A common protocol used to transfer e-mail
messages.
SNMP
Simple Network Management Protocol
socket
The association of a port with an IP address, serving as an identification of sender
or recipient.
stack
The software code which implements the protocol being used. In the case of the
NOE modules it is TCP/IP.
STP
Shielded Twisted Pair. A type of cabling consisting of several strands of wire
surrounded by foil shielding, twisted together.
subnet
A physical or logical network within an IP network, which shares a network address
with other portions of the network.
subnet mask
A bit mask used to identify or determine which bits in an IP address correspond to
the network address and which bits correspond to the subnet portions of the
address. The subnet mask is the network address plus the bits reserved for
identifying the subnetwork.
switch
A network device which connects two or more separate network segments and
allows traffic to be passed between them. A switch determines whether a frame
should be blocked or transmitted based on its destination address.
T
TCP
Transmission Control Protocol.
TCP/IP
A protocol suite consisting of the Transmission Control Protocol and the Internet
Protocol; the suite of communications protocols on which the Internet is based.
313
Glossary
U
UDP
User Datagram Protocol. A protocol which transmits data over IP.
Uni-Te
Télémecanique unified application protocol (used in S7, Premium, and Micro PLC
ranges).
URL
Uniform Resource Locator. The network address of a file.
UTP
Unshielded Twisted Pair. A type of cabling consisting of insulated cable strands
which are twisted together in pairs.
W
Web
Worldwide interconnection of stations based on Internet protocols. The most famous
one is HTTP (Web server).
WWW
World Wide Web. A hypertext-based, distributed information system in which clients
and servers are freely available.
314
Index
Numerics
140 CPU 6x1 x0, 21
140 NOE 771 10 FactoryCast module, 57
140 NWM 100 00, 19, 39
Important note, 40
A
addresses
IP, 266
swapping, 266
ASN.1, 187
B
BOOTP, 172
Display via web server, 241, 243
BOOTP Lite
Assigning IP addresses, 64
BOOTP Server
assigning IP address parameters, 54
C
cable connections
Ethernet, 49
Collision LED
Normal Conditions, 286
Communication Links, 93
Configure BOOTP
Via web server, 240
B
AC
Configure Communication, 88
Configure NOE
Via web server, 231
Configure SNMP
Fields, 234
Links, 234
Via web server, 233
connections supported, 81
Connector
100 BASE-FX, 45
100 BASE-T, 45
ConneXium, 154
ConnexView, 185
counters
resetting, 210
CPU 611 60
Cable connections, 45
CPU 651 x0, 97
Cable connections, 45
CPU configuration
Via web server, 224
Crash log
Clearing, 287
Clearing via FTP, 287
Reading, 287
Reading via FTP, 287
Crash Log Diagnostics Page
Links, 262
Customer Support, 65
315
Index
D
daylight savings time (DST), 206
DHCP, 172
direct connections, 210
E
ENTER buttons, 30
Error codes
mail service, 215
MSTR, 129, 132
TCP/IP Ethernet, 129
TCP/IP network, 130
Errors
Collision LED, 285
Detecting, 282
Fault LED, 284
Kernel LED, 284
LED indicators, 283
Run LED, 286
ESC buttons, 30
Ethernet Module, 97
Overview, 39
Ethernet module statistics
Via web server, 227
Ethernet Switch, 154
Ethernet TCP/IP
Modbus Application Protocol
(MBAP), 298
F
FactoryCast
Overview, 83
FactoryCast Module
Graphic Editor Link, 228
Overview, 39
FAST, 77, 205
Faulty Device Replacement, 172
FDR, 172
File Transfer Protocol (FTP), 80
Flash File System, 83
FTP
Downloading a new NOE Exec, 289
316
function blocks
FAST, 77, 205
MAST, 77, 205
G
Graphic Editor Link, 228
H
Health Bits
Global Data, 166
I/O Scanner, 166
High End, 21
HiVision, 185
Hot Standby, 265
Overview, 83
Hot Standby system
topology, 268
Hypertext Transport Protocol (HTTP), 81
I
I/O scan lists, 166
I/O Scanner
Device Control Block, 169
Peer Cop Health operation, 139
Illustration, 22
Indicators, 27
IP address parameters
Assigning, 54
Default IP address, 55, 56
K
Kernel, 291
key switches, 30
Keypad operation, 25
Index
L
LCDs
communications screens, 33
default screens, 31
displays, 29
LCD settings screens, 37
PLC operations screens, 32
system info screens, 36
leap seconds, 206
LED
Active indicators, 283
Application, 286
Collision error, 285
Fault error, 284
Kernel error, 284
Link error, 283
Run error, 286
LED Description, 27
local clock offsets, 206
M
MAC Address, 172
Management Information Base (MIB), 184
MAST, 77, 205
menus
communications, 33
default, 31
LCD display screens, 29
LCD settings, 37
PLC operations, 32
system, 36
Modbus Application Protocol (MBAP)
Description, 298
PDU, 299
Modbus I/O Scanner
Functionality, 74
Support, 39
MODBUS/TCP Server
Performance, 73
MSTR
Statistics (local), 135, 136
Statistics (remote), 137, 138
CTE error codes, 132
Operations, 133, 141
Read CTE, 142
Write CTE, 144, 145
MSTR error codes, 129
MSTR function
Error codes, 129
MSTR instruction
Peer Cop Health operation, 139
N
NOE, 272, 276
Crash log diagnostics via Web
server, 262
Properties via Web server, 261
PropertiesPage links, 261
NOE 771 00
Key Features, 39
NOE 771 01
Key Features, 39
NOE 771 10
Key Features, 39
NOE 771 11
Key Features, 39
NOE 771 x0
Cable connections, 45
Configuring, 190
Detecting errors, 282
Front panel components, 41
Responding to errors, 282
System maintenance, 281
NOE 771 x0 module
Assigning IP address parameters, 54
Installing, 47
NOE 771 x0, -1x, 97
NOE 771 xx
Quantum Ethernet TCP/IP modules, 73
NOE 771 xx module
Installing, 52
NOE Exec
Downloading a new, 288
Downloading via FTP, 289
NOE Option Module
Reset cycle, 141
317
Index
NWM 100 00, 97
Cable connections, 45
Front panel components, 41
Key Features, 39
relay systems, 210
Remote I/O communications status
Via Web server, 228
right buttons, 30
Role Name, 172
send requests, 210
Simple Network Management Protocol
(SNMP), 72, 184, 189
SNMP Manager, 185
Statistics
TCP/IP Ethernet, 146
Statistics (local)
MSTR, 135, 136
Statistics (remote)
MSTR, 137, 138
steady indicators, 31
submenus
default screen, 31
Init, 32
LCD contrast, 37
LCD display screens, 29
LCD Light, 37
Modbus Plus, 34
PLC operations screens, 32
serial port, 35
Start, 32
Stop, 32
System Info, 36
TCP/IP Ethernet, 34
subtrees
Address_Server, 197
Equipment_Profiles, 197
Global_Data, 196
I/O_Scanning, 195
NTP, 199
Port502_Messaging, 194
SMTP, 200
Transparent Factory Ethernet, 193
Web, 197
S
T
O
Overview, 13
P
parameters
setting daylight savings time, 245
setting NTP server IP address, 245
setting synchronization period, 245
setting time zone, 245
passwords, 80, 81
Peer Cop communications
Health status, 140
Peer Cop Health operation
MSTR instruction, 139
PLC data monitor
Via web server, 229
PLC operations screens, 32
polling times, 206
Presentation, 22
R
Schneider Private MIB, 191, 210
Security
Firewall, 51
FTP password, 57, 58
HTTP password, 58, 61
Modifying HTTP passwords, 62
Protocol port numbers, 51
Protocols, 51
318
TCP port numbers, 211
TCP/IP
Broadcast addressing, 304
Peer Cop Health operation, 140
TCP/IP Ethernet
Statistics, 146
TFE, 183, 184, 191
time accuracy, 206
Index
time zones, 246
customizing, 246
times
address swaps, 275
Transparent Factory
Transparent Factory Ethernet (TFE), 184
Transparent Factory Ethernet, 183
Transparent Factory Ethernet Private
MIB, 191
traps, 201
setting, 245
tz compilers, 246
Crash log diagnostics via Web
server, 262
Customer Support information, 263
Ethernet module statistics, 227
Features, 219
Home Utility Page, 220
Internet Explorer, 219
Netscape Navigator, 219
NOE Properties Page, 261
Password Request, 220
PLC data monitor, 229
Remote I/O communications status, 228
Welcome page links, 222
U
Universal Time, Coordinated (UTC), 206
up buttons, 30
user names, 80, 81
V
Version
Exec, 289
W
Web diagnostics, 82
Web pages
NTP Configuration, 244
Web Server
Accessing, 57
Web server
Accessing the home page, 219
Configure BOOTP, 240
Configure NOE, 231
Configure SNMP, 233
Configured Local Rack page, 223
Configured Local Rack page links, 223
CPU configuration fields, 225
CPU configuration screen, 224
319
Index
320
">