advertisement
Before Installation
Before installation of this unit, please note the following precautions.
#
WARNINGS
• If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.
#
CAUTION
• Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
✎ shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.
NOTE
• Mounting and wiring this product requires skills and experience. For best safety, leave the mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V DC power supply.
• Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
• Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.
• If the power is not turned ON (“There is an error in the speaker wiring. Please check the connections.” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained.
• If the console has a lid, make sure to install the unit so that the front panel will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.
• Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into contact with metal parts to protect the wires and to prevent short circuit.
• Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the
¤
wires or ground them to any metal part in the car.
• When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the
¢
connector of the left speaker to a front output terminal, do not connect the
¤ connector to a rear output terminal.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result.
• Reception may drop if there are metal objects near the Bluetooth antenna.
Bluetooth antenna unit
Ñ
Supplied accessories for installation
1 2
3
5 [1]
7 [1]
9
x1
4 [2]
(3 m)
x1
6 [1]
x1
8 [1]
(M5 × 6 mm)
x4
(2 m)
(M5 × 7 mm)
x4
x1
[1]
North America, South America sales area only
[2] DMX110BT only
x2 x1
x1
English | 19
B5A-2245-00_KEQ_EnFrEsPt.indb 19
Continued on the next page...
2017/09/07 13:46
Installation
Ñ
Installation procedure
1) To prevent a short circuit, remove the key from the ignition and disconnect the
¤
terminal of the battery.
2) Make the proper input and output wire connections for each unit.
3) Connect the wire on the wiring harness.
4) Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle.
5) Take Connector A on the wiring harness and connect it to the external power connector on your vehicle.
6) Connect the wiring harness connector to the unit.
7) Install the unit in your car.
8) Reconnect the
¤
terminal of the battery.
9) Press the reset button.
Installing the unit
Ñ
Non-Japanese cars
Ñ
Trim plate
1) Attach accessory
1
to the unit.
1
Ñ
Microphone unit (DMX110BT)
1) Check the installation position of the microphone
(accessory
4
).
2) Clean the installation surface.
3) Remove the separator of the microphone (accessory
4
), and stick the microphone to the place shown below.
4) Wire the microphone cable up to the unit with it secured at several positions using tape or other desired method.
5) Adjust the direction of the microphone (accessory
4
) to the driver.
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
✎
NOTE
• Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Ñ
Japanese cars (North America, South
America sales area only)
7
or
8
Car Bracket
4
Fix a cable with a commercial item of tape.
✎
NOTE
• Swap the clips if necessary.
7
or
8
20
B5A-2245-00_KEQ_EnFrEsPt.indb 20 2017/09/07 13:46
Installation
Ñ
Removing the trim plate
1) Use the extraction key (accessory
3
) to lever out the four tabs (two on the left part, two on the right part).
3
Ñ
Removing the unit
1) Remove the trim plate by referring to step 1 in
“Removing the trim plate”.
2) Insert the extraction key (accessory
2
) deeply into the slot as shown. (The protrusion at the tip of the extraction key must face toward the unit.)
2) Pull the trim plate forward.
2
3) With the inserted extraction key secured, insert the other extraction key into the slot.
4) Pull out the unit halfway.
2
✎
NOTE
• Be careful to avoid injury from the catch pins on the extraction key.
5) Pull the unit all the way out with your hands, being careful not to drop it.
B5A-2245-00_KEQ_EnFrEsPt.indb 21
English | 21
Continued on the next page...
2017/09/07 13:47
Installation
Ñ
Connecting wires to terminals
USB device [2]
USB terminal
[1]
(0.8 m)
5V
=
1A
Cap
MIC
Light Green
(Parking sensor wire)
Accessory
9
: Extension cable
PARKING BRAKE
For best safety, be sure to connect the parking sensor.
Connect to the vehicle’s parking brake detection switch harness.
Accessory
4
:
Bluetooth Microphone
(DMX110BT only)
Subwoofer Preout
Cap
SUB
WOOFER
Purple/White
(Reverse sensor wire)
Connect to vehicle’s reverse lamp harness when using the optional rear view camera.
REVERSE GEAR SIGNAL
Light Blue/Yellow
(Steering remote control wire)
STEERING WHEEL REMOTE CONTROL
To steering remote
To use the steering wheel remote control feature, you need an exclusive remote adapter (not supplied) matched to your car.
Connector B
Connector A
1 3 5 7
2 4 6 8
1 3 5 7
2 4 6 8
15A
AV-IN REAR FRONT
L
R
L
R R
L
V CAM VOUT
ANT
FM/AM antenna input
FM/AM antenna
Fuse (15A)
ISO Connector
Ñ
Wiring harness connector function guide
Pin
A-4
A-5
Color and function
Yellow Battery
Blue/White
[3]
Power Control
A-7
A-8
Red
Black
Ignition (ACC)
Earth (Ground) Connection
B-1/ B-2 Purple (+) / Purple/Black (–) Rear Right
B-3/ B-4 Gray (+) / Gray/Black (–) Front Right
B-5/ B-6 White (+) / White/Black (–)
B-7/ B-8 Green (+) /
Green/Black
(–)
Front Left
Rear Left
• Speaker Impedance: 4-8 Ω
!
CAUTION
Before you connect the commercially available ISO connectors to the unit, check the following condition:
• Make sure that the pin assignment of the connector matches with the KENWOOD unit.
• Take extra notice of the power wire.
• In case battery wire and ignition wire are not corresponding then change them accordingly.
• In case the car does not have an ignition wire, use a
22 commercially available interface.
AV-IN audio input
(Left; White, Right; Red)
Rear Audio Preout
(Left; White, Right; Red)
Front Audio Preout
(Left; White, Right; Red)
Visual Output (Yellow)
Rear view camera input (Yellow)
AV-IN visual input (Yellow)
[1]
USB maximum power supply current : DC 5 V
=
1 A
[2]
[3]
Sold separately
Max. 300mA, 12V
B5A-2245-00_KEQ_EnFrEsPt.indb 22 2017/09/07 13:47
Installation
North America, South America sales area only
Ñ
Connecting an iPod/iPhone
iPod/iPhone [2]
Lightning connector
KCA-iP103 (0.8m) [3]
1 3 5 7
2 4 6 8
1 3 5 7
2 4 6 8
15A
AV-IN REAR FRONT
L
R
L
R
CAM VOUT V
Accessory
5
Accessory 6
L
R
ANT
USB terminal
[1]
(0.8 m)
5V
=
1A
Speaker impedance: 4-8 Ω
White
To front left speaker
White/Black
Gray
To front right speaker
Gray/Black
Green
To rear left speaker
Green/Black
Purple
Purple/Black
To rear right speaker
Blue/White
(Power control/ Antenna control wire)
*
1
Connect either to the power control terminal when using the optional power amplifier, or to the power terminal for the booster amplifier of the film-type or short pole type antenna.
(Max. 300mA, 12V)
*1 If no connections are made, do not let the cable come out from the tab.
Cap
15A
AV-IN REAR FRONT
L
R
L
R
L
R
V CAM VOUT
ANT
[1]
iPod/iPhone maximum power supply current :
[2]
[3]
DC 5 V
=
1 A
Sold separately
Optional accessory
Red (Ignition wire)
Yellow (Battery wire)
ACC
Ignition key switch
B+
Car fuse box
Black (Ground wire)
¤
(To car chassis)
Battery
Not used
B5A-2245-00_KEQ_EnFrEsPt.indb 23
English | 23
Continued on the next page...
2017/09/07 13:47
advertisement
Related manuals
advertisement