Remote Arming by Telephone. Bosch Solution 2000, SOLUTION 3000
Add to My manuals150 Pages
Bosch Solution 2000 is a versatile security system that provides comprehensive protection for your home or business. With its advanced features and user-friendly interface, the Bosch Solution 2000 is the ideal choice for those seeking a reliable and effective security solution.
advertisement
60
en | Remote Arming by Telephone
9 Remote Arming by Telephone
Control Panel
This feature allows you to arm your system from any remote location by telephone. For obvious security reasons, you cannot disarm the system using this method. A touch-tone telephone is required to use this feature.
To remotely arm your system by telephone:
1.
Call the telephone number to which your control panel is connected. When the control panel answers the incoming call, a short jingle sounds.
– If you hear modem tones (a high tone and a low tone) when the control panel answers the incoming call, the system is programmed for remote arming by telephone. Wait for a pause in the tones and follow Step 2 to arm the system remotely.
2.
Press [*] on the touch-tone telephone to arm the system. Two beeps sound to indicate that the system is armed in AWAY Mode.
3.
Hang up the telephone. The system remains armed.
If the control panel does not answer the call, the ring count might be set to 0. If the control panel answers the call without modem tones, remote arming by telephone might not be enabled. To enable remote arming by telephone, select Option 2 in Location 177 (refer to
Communication Options 1, page 77). To set the number of rings before the control panel
answers, refer to Ring Count, page 75.
Notice!
Using this method with a partitioned control panel arms both areas in AWAY Mode. Arming individual areas is not available with this method.
2017.10 | 03 | F.01U.298.026
Installation Guide Bosch Security Systems, Inc.
advertisement
Key Features
- Supports up to 8 zones for comprehensive coverage
- Stay and Away arming modes for customizable protection
- Panic, fire, and medical alarms for emergency situations
- Remote arming and disarming via telephone or A-Link Plus Software
- Event Memory Recall Mode for easy review of system activity
- Fault Analysis Mode for quick troubleshooting
Related manuals
Frequently Answers and Questions
How many zones does the Bosch Solution 2000 support?
Does the Bosch Solution 2000 have a panic alarm?
Can the Bosch Solution 2000 be armed and disarmed remotely?
How do I reset the Bosch Solution 2000 to factory default settings?
advertisement
Table of contents
- 1 Title Page
- 3 Table of Contents
- 9 Introduction
- 9 About documentation
- 9 Bosch Security Systems, Inc. product manufacturing dates
- 11 System Overview
- 11 Product Matrix
- 11 Configuration and Parts
- 11 Control panel capacities
- 12 Parts list
- 12 Order separately
- 13 Installation workflow
- 14 Accessories
- 14 Codepads
- 16 Installer Menu
- 18 WE800EV2 receiver
- 19 HCT-4 keyfob
- 19 RADION receiver B810
- 19 RADION keyfobs
- 20 RADION repeater
- 20 RADION detectors
- 20 B308 Octo-output Module
- 21 B426/B426-M Conettix Ethernet Communication Modules
- 21 B450/B450-M Conettix Plug-in Communicator Interfaces
- 22 A-Link Plus Software
- 23 Remote Security Control
- 23 Remote Security Control Plus
- 23 Keyswitches
- 24 TF008 Plug Pack (TF008-B)
- 24 Install the transformer
- 24 DLA
- 25 Configuration
- 25 Installer Commands
- 25 Command 958 - Exit from Installer's Programming Mode without saving changes
- 25 Command 959 - Test IUI-SOL-ADAPTER
- 26 Command 960 - Save and exit from Installer's Programming Mode
- 26 Command 961 - Reset the Control Panel to Factory Default Settings
- 26 Command 962 - Copy the Control Panel Memory to IUI-SOL-ADAPTER
- 27 Command 963 - Copy IUI-SOL-ADAPTER data to the Control Panel
- 27 Command 965 - Set up Domestic Dialing Format
- 28 Command 966 - Enable/Disable the Automatic Stepping of Locations
- 28 Command 999 - Display the Control Panel Firmware Version Number
- 29 Disable Factory Defaults
- 31 System Operations
- 31 Arming the system in AWAY Mode
- 31 Disarming the system from AWAY Mode
- 32 Arming the System in STAY Mode 1
- 33 Disarming the system from STAY Mode 1
- 33 Arming the system from STAY Mode 2
- 34 Disarming the system from STAY Mode 2
- 34 Codepad duress alarm
- 34 Codepad panic alarm
- 35 Codepad fire alarm
- 35 Codepad medical alarm
- 35 Isolating zones
- 35 Standard isolating
- 36 Code to isolate
- 36 Fault analysis mode
- 37 Fault descriptions
- 39 Inquire cloud status
- 41 System Functions
- 41 Installer Code Functions
- 41 Add or Delete RF Wireless Devices
- 42 Add/Delete RF Repeater
- 43 Add/Delete RF Keyfob
- 43 Using an ICON codepad
- 44 Using an Alphanumeric codepad
- 45 Set the Number of Days until the First Test Report
- 45 Change Domestic Phone Numbers
- 46 Change Telco Arm/Disarm Sequence
- 47 Setting STAY Mode 2 Bypass Zones
- 48 Turning Report Monitor Mode On and Off
- 49 Walk Test Mode
- 49 Event Memory Recall Mode
- 50 AWAY/STAY 1 Arm/Disarm
- 51 Master Code Functions
- 51 Arm or Disarm both Areas at the Same Time
- 51 Arm or Disarm Single Area
- 52 Changing and Deleting User Codes
- 53 Adding Remote Radio User Codes
- 53 Deleting User/Radio Codes
- 54 Change Domestic Phone Numbers
- 54 Change Telco Arm/Disarm Sequence
- 54 Setting STAY Mode 2 Bypass Zone
- 54 Turning Outputs On and Off
- 55 Setting the Date and Time
- 55 Walk Test Mode
- 55 Event Memory Recall Mode
- 55 System reset
- 55 User Code Functions
- 55 Arm or Disarm both Areas at the Same Time
- 56 Arm or Disarm Single Area
- 56 Hold-Down Functions
- 56 Arm the System in AWAY Mode
- 56 Arm the System in STAY Mode 1
- 56 Arm the System in STAY Mode 2
- 57 Horn Speaker Test
- 57 Bell Test
- 57 Strobe Test
- 57 Turning Day Alarm On and Off
- 57 Fault Analysis Mode
- 57 Initiate a Modem Call
- 58 Reset Latching Outputs
- 58 Change the Codepad Buzzer Tone
- 58 Send Test Report
- 59 RF Keyfob Operations
- 59 Indications from RF Keyfob Operations
- 59 Remote Radio User Code Priority Levels
- 60 Remote Arming by Telephone
- 61 A-Link Plus Application
- 61 Modem Connection
- 61 Remote Connection with Customer Control
- 61 Remote Connection without Callback Verification
- 62 Remote Connection with Callback Verification
- 62 Answering Machine Bypass Connection
- 62 Network Connection
- 63 Direct Connection
- 63 Options
- 64 Configuring for email
- 64 Configure through B426/B426-M
- 66 Configure through B450/B450-M
- 68 Communication Information
- 69 Primary Telephone Number for Receivers
- 69 Secondary Telephone Number for Receivers
- 69 Transmission Format for Receivers
- 70 Subscriber ID Number for Receivers
- 70 IP Items for Receivers
- 71 Conettix Items for Receivers
- 72 External Network Modules
- 73 Network Module Cloud Connection
- 73 Password for A-Link Connection
- 73 DTMF Timing Compensation
- 73 Country Codes
- 73 Telco Arming Sequence
- 74 Telco Disarming Sequence
- 75 Call Back Telephone Number
- 75 Ring Count
- 76 Telephone Line Fail Options
- 77 Communication Options 1
- 77 Communication Options 2
- 78 Communication Options 3
- 79 A-Link Plus Options
- 79 Domestic Dialing
- 79 Domestic Dialing Funtion
- 80 Setting Up and Programming Domestic Reporting
- 81 Reporting Formats
- 81 Contact ID Format
- 82 SIA Format
- 82 System Reporting List
- 87 Access
- 87 Installer Code
- 87 User Codes
- 89 User Code Priority
- 91 Zone Information
- 91 Day Alarm Information
- 91 Day Alarm Resetting
- 91 Day Alarm Latching
- 91 Day Alarm Operation
- 92 EOL Resistor Value
- 93 Zone Programming
- 93 Zone Defaults
- 97 Zone Types
- 99 Zone Pulse Count
- 100 Zone Pulse Count Time
- 100 Zone Options 1
- 101 Zone Options 2
- 102 Zone Report Options
- 103 Keyswitch Zone Options
- 104 Zone Source
- 104 Swinger Shutdown Count for Siren
- 105 Swinger Shutdown Count for Report
- 106 STAY Mode 2 Automatically Bypass Zones
- 106 Zone Status Reporting Options
- 107 RF Information
- 107 RF Supervision Time
- 107 Anti-Jamming Sensitivity
- 108 RF Receiver
- 108 RF Options
- 108 RFID
- 109 RF Keyfob RFID
- 109 RF Device RFID
- 110 RF Reapter RFID
- 111 System Reporting Information
- 111 Arm/Disarm Reporting Options
- 111 Codepad Reporting Options
- 111 Access Denied
- 112 System Status Reporting Options
- 112 Test Reporting Time
- 113 Test Reporting Options
- 113 Reports
- 113 Zone Tamper Report
- 113 Walk Test Report
- 113 Bypass Report
- 113 Trouble Report
- 114 Sensor Watch Report
- 114 Alarm Restore Code
- 114 RF Receiver Trouble Report
- 114 RF Receiver Trouble Restore Report
- 114 RF Low Battery Report
- 114 Arm/Disarm Reports
- 115 Codepad Duress Report
- 115 Codepad Panic Report
- 115 Codepad Fire Report
- 115 Codepad Medical Report
- 115 AUX Power Supply Fail Report
- 115 AUX Power Supply Fail Restore Report
- 116 AC Fail Report
- 116 AC Fail Restore Report
- 116 Low Battery Report
- 116 Low Battery Restore Report
- 117 Programmable Outputs
- 117 Output Programming
- 123 B228 Output Mode
- 123 Output Event Types
- 130 Output Polarity
- 132 Output Timing
- 132 Pulsing Polarities
- 132 One-Shot Polarities
- 134 System Event Timers
- 134 Programming Entry/Exit Times
- 134 Entry Time 1
- 134 Entry Time 2
- 134 Exit Time
- 135 Entry Guard Time for STAY Mode
- 135 Delay Alarm Reporting Time
- 135 Sensor Watch Time
- 136 Codepad Lockout Time
- 136 Siren Run Time
- 136 Siren Sound Rate
- 136 Auto Arming Pre-Alert Time
- 137 Auto Arming Time
- 137 Auto Disarming Time
- 137 Kiss-Off Wait Time
- 137 Speaker Beep Volume
- 138 System and Consumer Options
- 138 System Options 1
- 139 System Options 2
- 139 System Options 3
- 140 System Options 4
- 141 System Option 5
- 141 Consumer Options 1
- 142 Consumer Options 2
- 143 Consumer Options 3
- 144 Partitioning
- 144 Programming
- 144 Partitioning Options 1
- 144 Partitioning Options 2
- 145 Partition Allocations
- 145 Zone Area Assignments
- 146 Codepad assignment
- 146 User code area assignments
- 148 Text Information
- 149 Back Page