advertisement
![Hydraulic Control Valve. Doosan G33P-5 Plus | Manualzz Hydraulic Control Valve. Doosan G33P-5 Plus | Manualzz](http://s1.manualzz.com/store/data/001123057_1-f57757b0a93cb41714fc70aa034a16ab-360x466.png)
Specification
Hydraulic Control Valve
CONTROL VALVE
Main Relief
Pressure
Tilt, Auxiliary
Relief Pressure
D20S-5
G20E-5
G20P-5
GC20E-5
GC20P-5
D25S-5
G25E-5
G25P-5
GC25E-5
GC25P-5
D30S-5
G30E-5
G30P-5
GC30E-5
GC30P5
G32E-5
G32P-5
D33SC-5
D35SC-5
G33P-5
G35P-5
18,100 ± 350 Kpa
2,625 ± 50 psi
19,500 ± 350 Kpa
2,825 ± 50 psi
21,550 ± 350 Kpa
3,125 ± 50 psi
24,000 (+500,0) Kpa
3,490 +75,-0 psi
15,500 ± 350 Kpa
2,250 ± 50 psi
15,500 ± 350 Kpa
2,250 ± 50 psi
15,500 ± 350 Kpa
2,250 ± 50 psi
15,500 ± 350 Kpa
2,250 ± 50 psi
Vehicle System 5
(1) Torque for bolts that hold control valve sections
Together .............40.5±2.5 N·m (360±24 lb·in)
(2) Torque for nut......... 4.9±0.5 N·m (43±12 lb·in)
(3) Torque for nut......... 4.9±0.5 N·m (43±12 lb·in)
(4) Torque for plug.............. 1±0.5 N·m (9±5 lb·in)
(5) Torque for screws... 5.4±2.7 N·m (48±24 lb·in)
(6) Adjust main relief valve pressure for lift as shown above. See Relief Valve Pressure Check in Testing And Adjusting.
(7) Adjust secondary relief valve pressure for tilt and side shift as shown above. See Relief Valve
Pressure Check in Testing And Adjusting.
(8) Torque for plug......5.5±2.5 N·m (492±24 lb·in)
(9) Torque for plug....63.7±2.5 N·m (564±24 lb·in)
(10) Torque for plug........................ 55.5±2.5 N·m
(492±24 lb·in)
(11) Torque for plug......30±2.5 N·m (260±24 lb·in)
(12) Adjust tilt and side shift flow rate by using 6mm hex-wrench if required. See Flow Control Valve
Adjustment in Testing And Adjusting.
(13) Torque for plug....................... 63.7±2.5 N·m
(564±24 lb·in)
Specification
advertisement
Related manuals
advertisement
Table of contents
- 7 Hydraulic Control Valve
- 8 Hydraulic Pump
- 8 Lift Cylinders
- 9 Full Free Triple Lift and Full Free Lift Primary
- 9 Lift Secondary
- 10 Tilt Cylinder
- 11 Carriage
- 12 Lift Relay Group
- 12 Standard Lift
- 13 Full Free Lift
- 14 Full Free Triple
- 15 Quad Lift
- 16 Lift & Tilt Mounting Group
- 17 Steering Wheel
- 18 Steering Gear
- 19 Steer Axle and Wheel
- 20 Steer Tire Installation
- 20 (GC Models Only)
- 20 Steer Wheel Mounting
- 20 Oil Cooled Disc Brake
- 21 Parking Brake
- 22 Hydraulic Schematic
- 24 Control Valve
- 24 External Configuration
- 24 Hydraulic Circuit
- 25 Inlet Block - Key On
- 26 Lift Spool - Positioned to Lift
- 27 Lift Spool - Positioned to Lower
- 27 Tilt Spool - Positioned for Forward Tilt
- 28 Tilt Spool - Positioned for Backward Tilt
- 29 Shifting
- 29 Pressure and Flow Control Section
- 30 Flow Control Adjustment - Tilt and Auxiliary
- 31 STEERING SYSTEM
- 31 Hydraulic Schematic
- 32 Steering Cylinder
- 33 Steering Gear
- 35 Brake Power Master Cylinder
- 37 Oil Cooled Disc Brake
- 37 Parking Brake
- 38 Delayed Engine Shutdown System
- 38 Operation
- 40 System
- 40 Diagnostic Fault Codes
- 44 OSS (Operator Sensing System)
- 45 Operation
- 45 Symbols of OSS
- 46 Operator Sensing System Schematic
- 49 Troubleshooting
- 49 Visual Checks
- 49 Performance Test
- 51 Hydraulic System and Mast
- 52 Hydraulic Pump
- 53 Hydraulic Control Valve
- 54 Lift and Tilt Cylinders
- 55 Steering System
- 56 Power Master Cylinder
- 57 Brake System
- 58 Hydraulic System
- 58 Relief Valve Pressure Check
- 60 Standard Lift Cylinder Air Removal
- 61 Mast and Carriage
- 61 Mast Adjustment - STD, FFL & FFT
- 66 Mast Adjustment - Quad
- 71 Carriage Adjustment
- 73 Quad Mast
- 74 Chain Adjustment
- 75 Chain Wear Test
- 76 Carriage and Mast Height Adjustment
- 76 Forks Parallel Check
- 77 Tilt Cylinder Alignment
- 79 Drift Test
- 80 Steering System
- 80 Steer Wheel Bearing Adjustment
- 80 Steering Axle Stop Adjustment
- 81 Steering System Pressure Check
- 83 Brake System
- 83 Brake System Air Removal
- 83 Parking Brake Test
- 84 Parking Brake Adjustment