advertisement
Steering System
Steer Wheel Bearing Adjustment
1
2
1 2
Bearing Adjustment
(1)Nut (2) Lock Washer
1. Tighten nut (1) slowly to 135 N·m (100 lb·ft) while the wheels is rotated in both directions to put the bearings into position.
2. Loosen nut (1) completely. Tighten nut (1) again to.............................. 50 ± 5 N·m (37 ± 4 lb·ft) .
3. Put the lock washer (2) on the nut and align the hole. In case of no match, rotate the nut (1) about 1/32 turn clockwise.
4. Apply loctite 242 on the threads of bots and tighten them at 8
±
3 N·m (6
±
2 lb·ft).
Steering Axle Stop Adjustment
1
A
2
3
4 5
IDCS132S
Steer Angle
(1) Bolt. (2) Nut. (3) Bolt. (4) Nut. (5) Bolts. (A) 80° angle.
Use the procedure that follows to make an adjustment to the steer axle turning angle.
1. Adjust the cylinder rod extension so it is equal on both sides of the axle.
2. Loosen nuts (2) and (4) on both sides of the steer axle.
3. Turn the steer wheel one direction until the steer cylinder rod extension measures 94mm(3.7 in) more than the straight ahead measurement.
4. Adjust stop bolt (1) on one side and stop bolt (3) on the other.
5. Tighten nut (2) on one side and nut (4) on the other side. Turn the steer wheel the opposite direction and do the same procedure for the opposite stop bolts. This will give a maximum cramp angle of 80°
Vehicle System 78 Testing & Adjusting
advertisement
Related manuals
advertisement
Table of contents
- 7 Hydraulic Control Valve
- 8 Hydraulic Pump
- 8 Lift Cylinders
- 9 Full Free Triple Lift and Full Free Lift Primary
- 9 Lift Secondary
- 10 Tilt Cylinder
- 11 Carriage
- 12 Lift Relay Group
- 12 Standard Lift
- 13 Full Free Lift
- 14 Full Free Triple
- 15 Quad Lift
- 16 Lift & Tilt Mounting Group
- 17 Steering Wheel
- 18 Steering Gear
- 19 Steer Axle and Wheel
- 20 Steer Tire Installation
- 20 (GC Models Only)
- 20 Steer Wheel Mounting
- 20 Oil Cooled Disc Brake
- 21 Parking Brake
- 22 Hydraulic Schematic
- 24 Control Valve
- 24 External Configuration
- 24 Hydraulic Circuit
- 25 Inlet Block - Key On
- 26 Lift Spool - Positioned to Lift
- 27 Lift Spool - Positioned to Lower
- 27 Tilt Spool - Positioned for Forward Tilt
- 28 Tilt Spool - Positioned for Backward Tilt
- 29 Shifting
- 29 Pressure and Flow Control Section
- 30 Flow Control Adjustment - Tilt and Auxiliary
- 31 STEERING SYSTEM
- 31 Hydraulic Schematic
- 32 Steering Cylinder
- 33 Steering Gear
- 35 Brake Power Master Cylinder
- 37 Oil Cooled Disc Brake
- 37 Parking Brake
- 38 Delayed Engine Shutdown System
- 38 Operation
- 40 System
- 40 Diagnostic Fault Codes
- 44 OSS (Operator Sensing System)
- 45 Operation
- 45 Symbols of OSS
- 46 Operator Sensing System Schematic
- 49 Troubleshooting
- 49 Visual Checks
- 49 Performance Test
- 51 Hydraulic System and Mast
- 52 Hydraulic Pump
- 53 Hydraulic Control Valve
- 54 Lift and Tilt Cylinders
- 55 Steering System
- 56 Power Master Cylinder
- 57 Brake System
- 58 Hydraulic System
- 58 Relief Valve Pressure Check
- 60 Standard Lift Cylinder Air Removal
- 61 Mast and Carriage
- 61 Mast Adjustment - STD, FFL & FFT
- 66 Mast Adjustment - Quad
- 71 Carriage Adjustment
- 73 Quad Mast
- 74 Chain Adjustment
- 75 Chain Wear Test
- 76 Carriage and Mast Height Adjustment
- 76 Forks Parallel Check
- 77 Tilt Cylinder Alignment
- 79 Drift Test
- 80 Steering System
- 80 Steer Wheel Bearing Adjustment
- 80 Steering Axle Stop Adjustment
- 81 Steering System Pressure Check
- 83 Brake System
- 83 Brake System Air Removal
- 83 Parking Brake Test
- 84 Parking Brake Adjustment