advertisement
8 Assembly
8 Assembly
8.1
Protective hood/V-belt pulley
1
3
4 5
6
7
8
2
11
12
21
20
9
10
6
13
14
13
4
14
Item
1
2
3
4
5
6
7
Designation
Hexagonal bolt
Thrust washer
Shaft
Distance bushing
Thrust collar
Sliding washer
Inner rubber ring
Item
8
9
10
11
12
13
14
Designation
Protective hood
Handle
Torx screw
Outer rubber ring
Stop flange
Retaining clip
Ball bearing
19
18
17
16
15
Item
15
16
17
18
19
20
21
Designation
V-belt pulley
Shim ring
Screw
Spring
Cutting attachment
Screw
Stop pin
1
61
Protective hood/V-belt pulley
8 Assembly
1.
Attach the outer retaining clip (13).
2.
Heat the cutting attachment (19) to approx. 100 °C (use industrial hot air gun).
3.
Press the ball bearing (14) up against the retaining clip (13).
4.
Insert the second retaining clip (13) and spacer bushing (4).
5.
Also press the second ball bearing (14) up against the retaining clip (13).
19
13
14
13
4
6.
Apply bonding compound to the fluted area (x) on the screws (20).
7.
Insert the screws (20) and stop pin (21).
8.
Mount the complete hood (8) with the parts 6,12,11,7,6 and 5 and screw the screws (17) with springs (18) into the thrust collar (5) (torque wrench setting
10 Nm).
Note: When attaching the hood, make sure you follow the correct order of the parts (see Fig. 8.1).
1
2
3
8
2
5
6
7
4
62
Protective hood/V-belt pulley
8 Assembly
9.
Set the inner thrust washer (2) and the distance bushing (4) onto the axle (3).
10.
Insert the axle (3) into the cutting attachment (19) that is premounted to the hood.
11.
Attach the shim ring (16) onto the axle (3).
12.
Hold the V-belt pulley (15) against it, block it by inserting a mandrel through the bore (x) and screw it on with the hexagonal bolt (1) (torque wrench setting
25 + 5.0 Nm).
13.
Screw on the handle (9) with the Torx screw (10).
9
10
15
1 x
Note: The V-belt pulley (15) is not fastened until the cutting disc is attached.
63
Protective hood/V-belt pulley
8 Assembly
64
Protective hood/V-belt pulley
advertisement
Related manuals
advertisement
Table of contents
- 5 Foreword
- 7 Safety instructions
- 7 Proper use
- 7 General notes
- 8 Fuel, Lubricants, and Coolants / Filling the tank
- 9 Starting up
- 10 Cutting discs
- 13 Kickback and pulling motion
- 14 Maintenance
- 15 Starting up
- 16 Attaching the cutting disc
- 17 Fuel, lubricants, and coolants
- 19 Storing fuel
- 20 Filling the tank
- 21 Starting the engine
- 22 Cold start
- 23 Warm start
- 23 Turning off the engine
- 24 Setting the carburetor
- 25 Technical data
- 27 Special tools
- 29 Disassembly
- 29 Cover/Handle
- 31 Clutch
- 35 Recoil starter
- 39 Filter cover/Filter
- 41 Ignition system module/intake manifold
- 49 Cylinder/Crankshaft
- 53 Vibration dampers
- 55 Protective hood/V-belt pulley
- 59 Disassembly/Inspection
- 59 Carburetor/Inspection
- 63 Assembly
- 63 Protective hood/V-belt pulley
- 67 Vibration dampers
- 69 Cylinder/Crankshaft
- 75 Ignition system module/intake manifold
- 79 Filter cover/Filter
- 81 Recoil starter
- 85 Clutch
- 89 Cover/Handle
- 91 Malfunction
- 93 Maintenance
- 93 Maintenance schedule
- 95 Cleaning the protective hood
- 96 Replacing the V-belt
- 97 Tightening the V-belt
- 98 Carburetor setting
- 100 Cleaning/Changing the air filter
- 103 Replacing the spark plug
- 105 Replacing the suction head
- 105 Replacing the starter rope
- 106 10.10 Miscellaneous
- 109 Torque values