advertisement
8.8
Clutch
4
1
2
3
6
5
7 x
8
9
10 11
12
13
Item
1
2
3
4
5
6
Designation
Muffler
Torx screw
Screw
Spring washer
Seal
Guard
18
17
16
Item
7
8
9
10
11
12
Designation
Crankcase half
Snap ring
Clutch drum
Needle sleeve
Guide disc
Clutch
15
Item
13
14
15
16
17
18
Designation
V-belt
Cover
Torx screw
Tension spring
Disc
Stopping ring
14
83
Clutch
8 Assembly
1.
Attach the snap ring (8) in the groove of the crankshaft.
2.
Attach the stopping ring (18) with recess to the snap ring (8) and disc (17).
3.
Grease the needle sleeve (10) with multipurpose grease.
4.
Press the needle sleeve (10) into the clutch drum (9).
17
10
5.
Press the guide disc (11) into the receptacle of the clutch drum (9).
6.
Block the piston with piston stop wedge (0117571) in the exhaust port of the cylinder (x).
x
0117571
7.
Press the clutch drum (9) onto the crankshaft.
8.
Tighten the clutch (12) with installation wrench (0117574) and ring wrench
(19 mm) (torque wrench setting 55 ± 0.2 Nm).
Note: Left hand thread x
0117574
84
Clutch
9.
Remove the stop wedge.
10.
Attach the guard (6) directly on the cylinder, then screw on the seal (5) and muffler (1) with Torx screw (2), screw (3) with disc (4) and tighten them (torque wrench setting 8 Nm).
11.
Attach the V-belt (13).
12.
Screw the cover (14) onto the crankcase half (7) with the Torx screws (15).
13.
Tighten the V-belt, see Chapter 10.4.
85
Clutch
8 Assembly
86
Clutch
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Foreword
- 7 Safety instructions
- 7 Proper use
- 7 General notes
- 8 Fuel, Lubricants, and Coolants / Filling the tank
- 9 Starting up
- 10 Cutting discs
- 13 Kickback and pulling motion
- 14 Maintenance
- 15 Starting up
- 16 Attaching the cutting disc
- 17 Fuel, lubricants, and coolants
- 19 Storing fuel
- 20 Filling the tank
- 21 Starting the engine
- 22 Cold start
- 23 Warm start
- 23 Turning off the engine
- 24 Setting the carburetor
- 25 Technical data
- 27 Special tools
- 29 Disassembly
- 29 Cover/Handle
- 31 Clutch
- 35 Recoil starter
- 39 Filter cover/Filter
- 41 Ignition system module/intake manifold
- 49 Cylinder/Crankshaft
- 53 Vibration dampers
- 55 Protective hood/V-belt pulley
- 59 Disassembly/Inspection
- 59 Carburetor/Inspection
- 63 Assembly
- 63 Protective hood/V-belt pulley
- 67 Vibration dampers
- 69 Cylinder/Crankshaft
- 75 Ignition system module/intake manifold
- 79 Filter cover/Filter
- 81 Recoil starter
- 85 Clutch
- 89 Cover/Handle
- 91 Malfunction
- 93 Maintenance
- 93 Maintenance schedule
- 95 Cleaning the protective hood
- 96 Replacing the V-belt
- 97 Tightening the V-belt
- 98 Carburetor setting
- 100 Cleaning/Changing the air filter
- 103 Replacing the spark plug
- 105 Replacing the suction head
- 105 Replacing the starter rope
- 106 10.10 Miscellaneous
- 109 Torque values