Calling. Siemens SP65
Реклама
Реклама
left page (24) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
24 Calling
Calling
Dialling with number keys
The phone must be switched on
(standby mode).
J
Enter the number (always with area/international dialling code).
A
]
A short press clears the last digit, a long press clears the entire phone number.
Press the Call key. The displayed phone number is dialled.
Ending a call
B
Press the End key briefly.
Press this key even if the person on the other end of the line has hung up first.
Setting the volume
It is only possible to adjust the volume during a call.
With the joystick.
I
Or
kl
With the plus/minus key.
If a car kit is used, its volume setting will not affect the usual setting on the phone.
Redialling previous numbers
To redial the phone number last called:
Press the Call key twice.
A
To redial other numbers that were dialled previously:
A
I
Press the Call key once.
Pick out the phone number from the list, then to dial press the …
… key.
A
left page (25) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
If the number is busy
If the called number is busy or cannot be reached because of network problems several options are available (depending on the service provider). An incoming call or any other use of the phone interrupts these functions.
Either
Auto. redial
§Auto dial§ The phone number is automatically dialled ten times at increasing time intervals. End with:
B
End key.
Or
Call back
b
§Call back§ Your phone rings when the busy number is free.
Press the Call key to dial the number.
Calling
Reminder
§Prompt§ A beep reminds you to redial the displayed phone number after
15 minutes.
Additional information
Ð
Store phone number in the
Addressbook/Phonebook.
§Handsfr.§
back from loudspeaker).
*
Press and hold to switch microphone off.
International dialling codes
0
Press and hold until a “+” is displayed.
§Country§ Press and select country.
Phone number memo
You can enter a phone number during the call. The person to whom you are speaking can hear these entries. When the connection has ended you can save or dial the phone number.
25
left page (26) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
26 Calling
Accepting a call
The phone must be switched on. An incoming call will interrupt any other use of the phone.
C
Press.
Or
Press.
A
A phone number transmitted by the network plus the corresponding name (possibly with a picture) are displayed if they are stored in the
Phonebook/Addressbook (p. 33).
Rejecting a call
§Reject§ Press.
Or
B
Press .
Warning!
Please make sure you have accepted the call before holding the phone to your ear.
This will avoid damage to your hearing from loud ringtones.
Additional information
*
Press and hold to switch off the ringtone and silent alert.
Â
Missed call display.
Handsfree
You can put the phone down during a call. You can then hear the caller via the loudspeaker.
§Handsfr.§ Activate handsfree talking.
C
Switch on.
I
/
kl
Regulate the volume with the joystick or the plus/minus key.
§Handsfr.§ Deactivate.
Warning!
Always switch off “handsfree talking” before holding the phone to your ear!
Otherwise, you will damage your hearing!
Swapping between
2 calls
b
Establish a second connection
You can call another number during a call.
C
Open call menu.
Hold
J
The current call is put on hold.
Now dial the new phone number or select
C
Open the call menu, then select Default book , and then select the phone number.
left page (27) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
When the new connection is established:
§Swap§ Swap between calls.
Incoming calls during a call
You may need to register for this service with your service provider and set your phone accordingly
(p. 80). During a call, you may be
advised that there is another call waiting. You will hear a special tone during the call. You have the following options:
• Accept the waiting call in addition to the first
§Swap§ Accept the waiting call, putting the current call on hold to do so.
Always proceed as above to swap between the two calls.
• Reject the waiting call
§Reject§ Press.
§Divert§
Or
The waiting call is diverted, for example, to the mailbox.
• Accept the waiting call and end the current call
End the current call.
B
C
Accept new call.
Calling 27
Ending call(s)
Press the End key.
B
After the Return to held call?
display, you have the following selection:
§Yes§ You accept the call on hold.
§No§ You end the second call too.
Conference
b
Call up to 5 parties one by one and link them together in a multiparty call. Some of the functions described may not be supported by your service provider or may have to be enabled specially.
A connection has already been established:
C
Open the call menu and select Hold . The current connection is maintained.
J
C
Now dial a new number.
When the new connection is established …
… Open the call menu and select Conference . The held call is joined.
Repeat procedure until all participants are linked together (up to
5 participants).
left page (28) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
28 Calling
Ending
B
All calls in the conference are ended when you press the End key.
Call options
The following functions are only available during a call:
C
Press.
Hold Hold current call.
Microphone on
If switched off, the person on the other end of the line cannot hear you (muting).
Also:
*
Press and hold.
Handsfree Playback through the loudspeaker.
Volume Adjust handset volume.
Default book Phonebook/Addressbook.
Conference
Time/charge Display talktime that has elapsed so far and (if set) charges incurred during
Send DTMF Enter tone sequences
(numbers) for remote inquiries to an answering machine.
Call transfer
=
Connect the original call to a second call. For you, both calls are now ended.
Main menu Access to the main menu.
Call status List all held and active calls
(e.g. participants in a conference).
Direct call
If this is active, only one number can be dialled.
Switch on
C
¢
T
¢ Security
¢
Direct call
C
Confirm selection.
Enter phone code.
J
When first prompted you define and enter the phone code (4–8 digits).
C
Confirm selection.
Please do not forget this code (p. 18)!
Ï
/
J
Select phone number from the Phonebook/
Addressbook or enter it.
C
Confirm.
left page (29) of SP65 FUG en, A31008-H7450-A1-1-7619 (03.03.2005, 11:41)
Apply
§Carol§
Switch off
To dial the phone number
(e.g. Carol’s phone number), press and hold the right soft key.
#
J
Press and hold.
Enter phone code.
C
Confirm input.
Tone sequences (DTMF)
You can, for example, enter control codes (numbers) for remote access to an automatic answering machine while another connection exists . These entries are transmitted directly as
DTMF codes (control codes).
C
Open the call menu.
Send DTMF
Select.
Calling 29
Using the Phonebook/
Addressbook
Store phone numbers and control codes (DTMF codes) in the
Phonebook/Addressbook in the same way as a normal entry.
J
0
J
0
J
Enter phone number.
Press until a “+” appears in the display (wait for the connection to be established).
Enter DTMF codes
(numbers).
If necessary, wait again for three seconds at a time for the receiver to process the entries safely.
Enter a name.
§Save§ Store entry.
You may also store just the
DTMFcodes (numbers) and then send them during the call.
Завантажити
Реклама
Ключові особливості
Black
132 x 176 pixels
MMC
Bluetooth
Multimedia Messaging Service (MMS)
Lithium-Ion (Li-Ion) 750 mAh