advertisement
![Wireing diagram. Mitsubishi LDT 323V | Manualzz Wireing diagram. Mitsubishi LDT 323V | Manualzz](http://s1.manualzz.com/store/data/001979871_1-74d83d38d8fed5197a7874760a371046-360x466.png)
● The following diagram shown accessories fully equiped.
L1 L2 L3 N
Extension terminals
Power supply
Less than 2m
RS1 RS2 513 P1 P2 97 C1 A1
See Fig.1.
D2 D1 413 U1
Electronic trip relay(ETR)
Reset circuit Power circuit
Alarm contacts
SHT CC
UVT M
Main circuit
N1 N2 Z1 Z2
NCT * ZCT *
* Voltage forbid to be applied
FG
Dielectric test forbidden
P4 574 564 554 544 534 524 98 C2 A2 DT2
Short bar
DT1 414 U2
Open to trip
(less than 2m)
Electronic trip relay Control power circuit / alarm contact
OCR alarm
Electrical operation circuit
Terminal description
13
11
14
12
U1 U2
413 414
~
~
53
51
54
52
Auxiliary switch "a"
Auxiliary switch "b"
Motor charging
Charged signal
D1
DT1 DT2
A1
D2
A2
Voltage Input terminal of UVT
Trip terminal of UVT (Remote trip)
Closing coil
Shunt trip C1 C2
97
P1
P4
98
P2
OCR alarm
Power supply for ETR
FG of power supply (FG:Frame Ground)
Alarm reset (Trip cause LED, alarm contact) RS1 RS2
513
Z1
, 524 ~ 574
Z2
Alarm contacts
For external ZCT
For Neutral CT
(Note) N1 N2
Extension terminals
For external display DP2
For Interface unit
For VT unit
Note; Do not connect the NCT type CW-40LM (for AE-SS series).
CC
M
UVT
AX
AL
CLS
SBC
CL
Accessory Symbols
SHT Shunt tripping device
Closing coil
Motor(Motor charging device)
UVT coil
Auxiliary switch
OCR alarm switch
Charge limit switch
Shorting b-contact
Cell switch
Internal wiring
External wiring (user's wiring)
Control circuit connecter (drawout type)
51 41 31 21 11 53 43 33 23 13
Breaker
341 331 321 311
52 42 32 22 12 54 44 34 24 14
Breaker
344 342 334 332 324 322 314 312
Cell switch
Auxiliary switch(normal close) Auxiliary switch(normal open)
Fig.1
UVT controller wiring
100-120V AC type
200-240V AC type
DC types
380-460V AC type input input
D2 D1
+
IN2 IN1 external unit
OUT4 OUT3
D2 D1
Cell switch
Note;
● On the drawout type, the cables should have the length which allow the control circuit terminal block to be moved to the left or right by 5mm.
●
When a coil load is connected in the same control circuit as the ETR, surge absorbers are required to absorb the surge voltage.
● OCR alarm (AL)
The contact output of the OCR alarm(Standard type AL) is the one-pulse output and the output time is 30~50ms.
For this reason, this output needs self-holding circuit.
●
Closing coil (CC)
As CC is one-pulse driven, it is not necessary to insert AXb for burning prevention purposes.
Inserting AXb will cause anti-pumping function to be ineffective.
●
Under voltage trip device (UVT)
Use the switch that can open and close DC150V, 0.5A to remote trip.
Remote trip terminal has short bar at shipment, so remove it before using this function.
Disconnect the voltage input wires during dielectric testing of main circuit.
● voltage. (longer than 1sec.)
advertisement