Assembly. Briggs & Stratton 2050PSI, CleanShot 020206-0, CLEANSHOT 2050PSI

CleanShot™ 2050 PSI Pressure Washer

Required Assembly Tools

NO Tools Required for Assembly

ASSEMBLY

IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer.

Remove Pressure Washer From

Carton

1.

Remove the parts bag, accessories, and inserts included with pressure washer.

2.

Slice two corners at the end of carton from top to bottom so the panel can be folded down flat.

3.

Remove pressure washer from carton.

Carton Contents

Items in the carton include:

• Main Unit

• High Pressure Hose

• Spray Gun

• Nozzle Extension

• Turbo Nozzle

• Utility Brush with Adapter

• Accessory Storage Bag

• Safety Goggles

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Engine Manual

• Owner’s Registration Card

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the pressure washer helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available.

To prepare your pressure washer for operation, you will need to perform these tasks:

1.

Fill out and send in registration card.

2.

Add oil to engine crankcase.

3.

Add fuel to fuel tank.

4.

Connect high pressure hose to spray gun and pump.

5.

Connect water supply to pump.

6.

Attach nozzle extension to spray gun.

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

• Refer to engine manual for oil and fuel fill information.

• Damage to equipment resulting from failure to follow this instruction will void warranty.

• Refer to engine owner’s manual and follow oil and fuel recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.

6

CleanShot™ 2050 PSI Pressure Washer

Connect Hose and Water Supply to

Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

1.

Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 1).Tighten by hand.

Figure 1 — Connect High Pressure Hose to Spray Gun

Connect high pressure hose here

NOTE: Remove and discard all pump shipping caps before attaching hoses.

2.

Attach other end of high pressure hose to high pressure outlet on pump (Figure 2).Tighten by hand.

Figure 2 — Connect High Pressure Hose to Pump

4.

Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.

Connect the garden hose (not to exceed 50 feet in length) to the water inlet.Tighten by hand (Figure 3).

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

• Damage to equipment resulting from failure to follow this instruction will void warranty.

6.

Turn ON the water and squeeze the trigger on the gun to purge the pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

• Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing adequate eye protection.

3.

Before connecting garden hose to water inlet, inspect inlet screen (Figure 3). Clean screen if it contains debris or have it replaced if damaged. DO NOT RUN

PRESSURE WASHER IF INLET SCREEN IS DAMAGED.

Figure 3 — Connect the Garden Hose to Water Inlet

Inspect inlet screen, DO NOT use if damaged; clean if dirty.

CHECKLIST BEFORE

STARTING ENGINE

Review the unit’s assembly to ensure you have performed all of the following.

1.

Check that oil has been added to proper level in the engine crankcase.

2.

Add proper gasoline to fuel tank.

3.

Check for properly tightened hose connections.

4.

Check to make sure there are no kinks, cuts, or damage to high pressure hose.

5.

Provide a proper water supply at an adequate flow.

6.

Be sure to read “Safety Rules” and “How To Use Your

Pressure Washer” before using pressure washer.

7