ITEM #0470442
8 GAL. OIL-FREE AIR COMPRESSOR
MODEL #0300841
KOBALT® and the K Design® are registered trademarks of LF, LLC. All Rights Reserved.
Français p. 14
Español p. 27
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts?
Before returning to your retailer, call our customer service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST,
Monday - Friday.
AB13785
1 kobalttools.com
TABLE OF CONTENTS
Specifications
Package Contents
Hardware Contents
Parts Description
Safety Information
Preparation
Assembly Instructions
Operating Instructions
Care and Maintenance
Troubleshooting
Warranty
Replacement Parts List
PRODUCT SPECIFICATIONS
Model No.
Pump
Motor
Voltage/Amps/Hz
Air Tank Capacity
Cut-in Pressure
Cut-out Pressure
CFM @ 40 PSI
CFM @ 90 PSI
Power Cord
0300841
Oil free, direct drive, single stage
1.8 Hp
120/12.5/60
8 gallon
120 PSI
150 PSI
5.0
4.0
SJT 16 AWG / 72 in. length
NOTE
: Avoid use of extension cords. If use of an extension cord cannot be avoided, the cord should be a minimum wire size of 12 AWG and no longer than 30 feet.
Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. kobalttools.com
2
7
7
8
9
10
12
13
3
4
5
2
3
PACKAGE CONTENTS
E
H
C
D
F
I
K
HARDWARE CONTENTS
AA BB
J
G
PART DESCRIPTION
A
Electric Motor & Air Compressor Pump
B
Air Tank
C
Tank Pressure Gauge
D
Air Pressure Regulator
E
Regulated Pressure Gauge
Quick Coupler
F
G
Air Tank Drain Valve
H
Pressure Relief Valve
I
ON/OFF Switch
J
Power Cord
K
Handle Kit
L Wheel
M
Air Filter
CC DD EE
M8 × 15
Screw
Qty. 2
M10 Nut
Qty. 2
M10 Bolt
Qty. 2
Ø10 Washer
Qty. 2
Ø10 Spring Washer
Qty. 2
M
FF
B
Wheel Cap
Qty. 2 kobalttools.com
A
1
1
1
1
2
1
QTY
1
1
1
1
1
1
1
3
L
PARTS DESCRIPTION
PART
A
PART NAME
Electric Motor
Air Compressor Pump
PART DESCRIPTION
The motor is used to power the pump. It contains a thermal overload protector. If the motor overheats for any reason, the thermal overload protector will shut it down in order to prevent the motor from being damaged.
The pump is used to compress the air and discharge it into the tank via the piston moving up and down in the cylinder.
B
C
Air Tank
Tank Pressure Gauge
The tank is used to store the compressed air.
The gauge is used to measure the stored air pressure level of
the tank. It is not adjustable by the operator and does not
indicate line pressure.
D Air Pressure Regulator
The regulator is used to adjust line pressure to the tool you are
using. Turn the knob clockwise to increase pressure and
counterclockwise to decrease pressure.
E Regulated Pressure Gauge
The gauge is used to measure the regulated outlet pressure.
F Quick Coupler
G
H
J
I
Air Tank Drain Valve
Pressure Relief Valve
On/Off Switch
Power Cord
For this compressor, the quick coupler is also used as the air line outlet. The outlet is used to connect the 1/4 in. NPT air hose.
The drain valve is used to remove moisture from the air tank
after the unit is shut off.
The valve is used to prevent system failures by relieving pressure from the system. If the pressure reaches the preset level and the pressure switch will not shut down the motor, it will automatically pop open. You can also pull the ring on the valve to open.
This switch turns on the compressor and is operated manually.
When in the ON position, it allows the compressor to start up or shut down automatically, without warning, upon air demand.
ALWAYS set this switch to OFF when the compressor is not being used and before unplugging the compressor.
This product is for use on a nominal 120-volt circuit and should be grounded. A cord with a grounding plug as illustrated must be used. Make sure that the product is connected to an outlet that has the same configuration as the plug. No adapter should be used with this product.
Grounded outlet
Plug
Grounding Pin
4 kobalttools.com