advertisement
![Connecting the BSM-2 to your display. Simrad BSM-2 | Manualzz Connecting the BSM-2 to your display. Simrad BSM-2 | Manualzz](http://s2.manualzz.com/store/data/061659207_1-30cc69c4193bedb641d208ff83eed76c-360x466.png)
Strap settings for transducer impedance
Each transducer connector has 3 transducer impedance jumpers, used to assure max power is being transferred to the sonar elements.
The transducer list on page 21 shows how to set the jumper for transducers that can be used with BSM-2.
XDCR HIGH XDCR LOW
J8 J7
1 1
C
B
A
F
E
D
For any transducer not included in the list, connect the jumper to the impedance selector according to the transducer impedance based on the following table:
HIGH FrEQ
A 100 Ohm
B 270 Ohm
C 400 Ohm
LoW FrEQ
D 100 Ohm
E 270 Ohm
F 400 Ohm
If the Transducer impedance doesn’t appear in the table, select the closest impedance that is higher than the customers value.
Connecting the BSM-2 to your display
The BSM-2 connects to your display system over an
Ethernet network, either directly or via a Network
Expansion Port. Refer Cabling diagram, page 9.
When connected to an NSO, the RJ45 to 5 pin cross-over
Ethernet cable included with the NSO system must be used.
For details refer to the display system’s Installation manual.
14 | BSM-2 Installation manual
BSM-2_IM_988-0170-09_A.indb 14 2/14/2011 2:52:31 PM
Setting up the transducers
The BSM-2 is compatible with Airmar’s Transducer ID protocol. If you have an Airmar transducer that supports this feature, BSM-2 will read your transducer’s specification at start-up and automatically adjust the frequency and temperature settings. The transducer’s
XID wire (orange) should be connected to the XDCR_ID_
HIGH/LOW terminal in the TEMP HIGH/LOW connector as shown below.
TEMP HIGH
1
J5 rEF.
1
2
CoLor
Orange
Shield
SIGNAL
XID
XID GND x2
MENU WIN
1 2
If your transducer doesn’t support Airmar’s Transducer
ID protocol, the transducer selection and configuring needs to be done from the display as shown on the graphics below.
A detailed description is found in the relevant documentation for the display.
BSM-2_IM_988-0170-09_A.indb 15
BSM-2 Installation manual | 15
2/14/2011 2:52:31 PM
advertisement
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 About this manual
- 5 The BSM-2 module layout
- 6 Parts included in package
- 6 Required tools and supplies
- 7 Installation and wiring
- 7 Mounting location
- 8 Securing BSM-2 module
- 8 Wiring
- 8 General
- 9 Grounding the unit
- 9 Wiring diagram
- 10 Terminal connections
- 11 Power connection
- 11 Transducers connection
- 14 Connecting the BSM-2 to your display
- 16 Trouble shooting
- 20 Dimensional drawing
- 21 Spare parts and accessories
- 21 Spare parts
- 21 Accessories
- 21 Transducers
- 29 Einleitung
- 29 Informationen zu diesem Handbuch
- 29 Aufbau des BSM-2-Moduls
- 30 Im Paket enthaltene Teile
- 30 Erforderliches Werkzeug und Zubehör
- 31 Installation und verkabelung
- 31 Einbauposition
- 32 Sichern des Moduls BSM
- 32 Verkabelung
- 32 Allgemeines
- 33 Erden des Geräts
- 33 Schaltplan
- 34 Anschlüsse
- 35 Stromanschluss
- 35 Schwingeranschluss
- 38 Display
- 40 Fehlerbehebung
- 41 Technische Angaben
- 44 Maßzeichnung
- 45 Ersatzteile und Zubehör
- 45 Ersatzteile
- 45 Zubehör
- 45 Schwinger
- 53 Introducción
- 53 Sobre este manual
- 53 Disposición modular del BSM
- 54 Piezas incluidas en el paquete
- 54 Herramientas y suministros necesarios
- 55 Instalación y cableado
- 55 Lugar de instalación
- 56 Fijación del módulo del BSM
- 56 Cableado
- 56 General
- 57 Conexión a tierra de la unidad
- 57 Diagrama de cableado
- 58 Conexiones de terminales
- 59 Conexión de alimentación
- 59 Conexión de transductores
- 62 Conexión del BSM-2 a su pantalla
- 64 resolución de problemas
- 68 Dimensiones
- 69 Piezas de repuesto y accesorios
- 69 Piezas de repuesto
- 69 Accesorios
- 69 Transductores
- 77 Introduction
- 77 À propos de ce manuel
- 77 Disposition du module BSM
- 78 Composants inclus dans l'emballage
- 78 Outils et matériaux nécessaires
- 79 Installation et câblage
- 79 Emplacement de montage
- 80 Montage du module BSM
- 80 Câblage
- 80 Généralités
- 81 Mise à la terre de l'unité
- 81 Schéma de câblage
- 82 Raccordements du bornier
- 83 Raccordement de l'alimentation
- 83 Raccordement des transducteurs
- 92 Dessin dimensionnel
- 93 Composants de rechange et accessoires
- 93 Composants de rechange
- 93 Accessoires
- 93 Transducteurs
- 101 Introduzione
- 101 Informazioni su questo manuale
- 101 Struttura del modulo BSM
- 102 Parti comprese nella confezione
- 102 Strumenti e attrezzature necessari
- 103 Installazione e cablaggio
- 103 Ubicazione di montaggio
- 104 Fissaggio del modulo BSM
- 104 Cablaggio
- 104 Informazioni generali
- 105 Messa a terra dell'unità
- 105 Diagramma di cablaggio
- 106 Connessioni terminali
- 107 Connessione dell'alimentazione
- 107 Connessione trasduttori
- 110 Collegamento del BSM-2 al display
- 112 risoluzione dei problemi
- 116 Disegno dimensionale
- 117 Parti di ricambio e accessori
- 117 Parti di ricambio
- 117 Accessori
- 117 Trasduttori