Vent Assem bly Illustrations. Suburban SFV-42F, NT-24SP, SH-35, P-30S/40, P-40, SF-35, SH-42F, NT.12SE, SFV-42, NT.16SE
Add to My manuals40 Pages
advertisement
![Vent Assem bly Illustrations. Suburban SFV-42F, NT-24SP, SH-35, P-30S/40, P-40, SF-35, SH-42F, NT.12SE, SFV-42, NT.16SE | Manualzz Vent Assem bly Illustrations. Suburban SFV-42F, NT-24SP, SH-35, P-30S/40, P-40, SF-35, SH-42F, NT.12SE, SFV-42, NT.16SE | Manualzz](http://s1.manualzz.com/store/data/002326402_1-45196fd0b122c9220a545bebefb681a0-360x466.png)
VENTING
Venting- By definition of a Direct Vent Sealed Combustion Furnace, it must be vented to the outside atmosphere and also draw combustion air from outdoors. Therefore, it is imperative that the vent be unobstructed and there must be a seal between the exhaust and intake (caulking) . Refer to the vent assembly installation in the manual. The vent must be straight. There can be no offsets or turns in the vent. All vent tubes which connect to the furnace exhaust and intake must overlap a minimum of 1/2" on intake, and 1 1/4" on exhaust. Check your furnace model number for vent installation procedures. Vents cannot be altered as supplied from the factory.
VENT ASSEMBLY INSTALLATION (SF and SH SERIES)
Figure 2
S F
Figure 2A
S H
6
VENT ASSEMBLY INSTALLATION (SF and SH SERIES)
Figure 3
S F
Figure 3A
SH and S H D -2542
7
VENT ASSEMBLY INSTALLATION (SF and SH SERIES)
Figure 4
S F
Figure 4A
S H
8
VENT ASSEMBLY INSTALLATION (SFV)
Figure 5
Figure 5A
9
Figure 6
Figure 6A
10
VENT ASSEMBLY INSTALLATION (DD SERIES)
Note: Vent cap must be installed on DD furnace when bench testing.
Figure 7
11
VENT ASSEM BLY INSTALLATION (NT SERIES)
Figure 8
N T-12/16/20S E
Figure 9
N T-12/16/20S and S E
Figure 10
NT-12/16S
12
VENT ASSEM BLY INSTALLATION (NT SERIES)
Figure 11
N T-20S
Figure 12
N T-24/30/34S P
P -30S
13
VENT ASSEM BLY INSTALLATION (NT SERIES)
Figure 13
N T-24/30/34S P
P -30
EXTENSION TUBE
KIT NUM BER
520498
520499
520500
520501
M IN./M AX. LENGTH
(Extension Tube Range)
Figure 14
N T-24/30/34S P
P-30S
2-1/4" to 3-1/8"
3-1/8" to 4-7/8"
4-7/8" to 7"
7" to 9"
EXTENSION TUBE
KIT NUM BER
520593
520594
520595
520596
M IN./M AX. LENGTH
(Extension Tube Range)
2-1/4" to 3-1/8"
3-1/8" to 4-7/8"
4-7/8" to 7"
7" to 9"
Figure 15
N T-40
P -40
14
VENT ASSEM BLY INSTALLATION (NT-40 and P-40)
Figure 16
N T-40
Figure 17
P -40
15
advertisement
Related manuals
advertisement
Table of contents
- 3 General Service Inform ation
- 4 Furnace Spec Sheet
- 5 Installation
- 6 Vent Assem bly Illustrations
- 16 Return Air Illustrations
- 17 Ducting Illustrations
- 18 Installation Requirem ents (DD, NT and P Model Furnaces)
- 19 Installation Requirem ents (SF, SH and SHD-2542 Model Furnaces)
- 20 Installation Requirem ent (SFV Model Furnaces)
- 21 Furnace Specifications (DD, NT and P Model Furnaces)
- 22 Furnace Specifications (SF, SFV, SH, and SHD-2542 Model Furnaces)
- 23 Sequence of Operation (Tim e Delay Relay Equipped Furnaces)
- 24 Sequence of Operation (Fan Control Module Board (520820) Equipped Furnaces)
- 25 Sequence of Operation (24 VAC Fan Control Module Board (520947)
- 26 Sequence of Operation (SHD-2542 Furance)
- 27 Trouble Shooting Flow Chart (Furnaces Equipped with Tim e Delay Relay)
- 28 Trouble Shooting Flow Chart (Furnaces Equipped with Fan Control Module Board)
- 29 for Suburban 24-Volt AC Electronic Ignition Furnaces
- 30 W iring Diagram s
- 35 Furnace Rem oval
- 37 SF, SH and SHD-2542 Electrode Gap Specifications & Positioning
- 38 NT and Park Model Electrode Gap Specifications & Positioning
- 39 Maintenance