Chapter 2: Connecting the Wireless-G Broadband Router. Linksys WRT54GS, WRT54GS EU
Add to My manuals
453 Pages
advertisement
Wireless-G Broadband Router with SpeedBooster
Chapter 2: Connecting the Wireless-G Broadband Router
Overview
This chapter includes two sets of instructions. If the Wireless-G Broadband Router will be the only router in your network, follow the instructions in “Hardware Installation for Connection to Your
Broadband Modem.” You may wish to run some applications, such as Parental Control, for only certain PCs on your network and will need to run the Wireless-G Broadband Router behind another router to do this. If you want to install the Wireless-G Broadband Router behind another router in your network, follow the instructions in “Connecting One Router to Another.”
Hardware Installation for Connection to Your Broadband Modem
1. Power down your network devices.
2. Locate an optimum location for the Router. The best place for the Router is usually at the center of your wireless network, with line of sight to all of your mobile stations.
3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be.
4. Connect a standard Ethernet network cable to the Router’s Internet port. Then, connect the other end of the Ethernet cable to your cable or DSL broadband modem.
5. Connect your network PCs or Ethernet devices to the Router’s numbered ports using standard Ethernet network cabling.
IMPORTANT: Make sure you use the power adapter that is supplied with the Router. Use of a different power adapter could damage the Router.
Figure 2-1: Connecting Your Modem
Figure 2-2: Connecting Your Network Devices
6. Connect the AC power adapter to the Router's Power port and the other end into an electrical outlet. Only use the power adapter supplied with the Router. Use of a different adapter may result in product damage.
Now that the hardware installation is complete, proceed to “Chapter 3: Configuring the Wireless-G Broadband
Router,” for directions on using the Router’s Web-Based Utility to configure the Router’s settings for your network.
Figure 2-3: Connecting the Power
Chapter 2: Connecting the Wireless-G Broadband Router
Overview
4
Wireless-G Broadband Router with SpeedBooster
Connecting One Router to Another
Some applications, such as Parental Control, apply setting to all PCs connected to the Router. Sometimes, you may not want those settings to apply to all settings in your network. When this is the case, you may want to connect the Router behind another, so you can have some PCs connected to the Router with Parental Control and some connected to a Router without.
Before you connect one Router to another, you must make sure that both have different IP Addresses. This is mandatory because both routers may be set to the same IP address by default, right out of the box. If both routers have the same IP address, then you may not be able to set up the Router with Parental Control.
First, make sure the Router is NOT connected to your network. Then follow these instructions:
1. To access the other router’s Web-based Utility, launch Internet Explorer or Netscape Navigator, and enter the other router’s default IP address, 192.168.1.1, or whatever IP Address you have set it to, in the Address field. Then, press
Enter.
2. A password request page will appear. Leave the User Name field blank. In the Password field, enter the password you have set (the default password is admin). Then click the OK button.
3. The first screen that appears will display the Setup tab. In the Network Setup section, there is a setting called Local IP
Address, which is set to 192.168.1.1. Change this to 192.168.2.1.
4. Click the Save Settings button to save your change, and then exit the Web-based Utility.
5. Power down your network devices. Now you will begin the hardware installation of Broadband Router.
6. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at the center of your wireless network, with line of sight to all of your mobile stations.
7. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be.
Internet Broadband
Modem
Router Wireless-G
Broadband
Router
Figure 2-4: Connecting the Router Behind Another
NOTE: Steps 1-4 are instructions for a typical
Linksys router; however, if you are using a non-
Linksys router, refer to the other router’s documentation for instructions on how to change its local IP address to 192.168.2.1.
Internet
Router
Broadband
Modem
Chapter 2: Connecting the Wireless-G Broadband Router
Connecting One Router to Another
Wireless-G
Broadband
Router
Multiple PCs
Figure 2-5: Diagram for Connection to Another Router
5
Wireless-G Broadband Router with SpeedBooster
8. Connect a standard Ethernet network cable to the Broadband Router’s Internet port. Then, connect the other end of the
Ethernet cable to one of the numbered Ethernet ports on your other router.
Figure 2-6: The Router with the Internet Connection is connected through the Internet Port
9. Decide which network computers or Ethernet devices you want to connect to the Broadband Router.
IMPORTANT: Make sure you use the power adapter that is supplied with the Router. Use of a different power adapter could damage the Router.
Disconnect the selected computers or devices from the other router, and then connect them to the Broadband Router’s numbered ports using standard Ethernet network cabling.
Figure 2-7: Connecting Your Network Devices
10. Connect the AC power adapter to the Broadband Router's Power port and the other end into an electrical outlet. Only use the power adapter supplied with the Broadband Router. Use of a different adapter may result in product damage.
Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G
Broadband Router,” for directions on using the Router’s Web-Based Utility to configure the Router’s settings for your network.
Chapter 2: Connecting the Wireless-G Broadband Router
Connecting One Router to Another
Figure 2-8: Connecting the Power
6
advertisement
Key Features
- Black, Blue
- Fast Ethernet
- Ethernet WAN
- Ethernet LAN (RJ-45) ports: 4
- Web-based management
Related manuals
advertisement
Table of contents
- 1 English, User Guide
- 3 Chapter 1: Getting to Know the Wireless-G Broadband Router
- 5 Chapter 2: Connecting the Wireless-G Broadband Router
- 8 Chapter 3: Configuring the Wireless-G Broadband Router
- 34 Appendix A: Troubleshooting
- 46 Appendix B: Specifications
- 47 Appendix C: Warranty Information
- 48 Appendix D: Regulatory Information
- 62 Appendix E: Contact Information
- 259 Deutsch, Benutzerhandbuch
- 261 Kapitel 1: Kennenlernen des Wireless-G Broadband-Routers
- 263 Kapitel 2: Anschließen des Wireless-G Broadband-Routers
- 266 Kapitel 3: Konfigurieren des Wireless-G Broadband- Routers mit SRX400
- 294 Anhang A: Fehlerbehebung
- 308 Anhang B: Spezifikationen
- 309 Anhang C: Garantieinformationen
- 310 Anhang D: Zulassungsinformationen
- 324 Anhang E: Kontaktinformationen
- 326 Français, Guide de l'utilisateur
- 328 Chapitre 1 : Présentation du routeur haut débit sans fil G
- 330 Chapitre 2 : Connexion du routeur haut débit sans fil - G
- 333 Chapitre 3 : Configuration du routeur haut débit sans fil - G
- 359 Annexe A : Dépannage
- 373 Annexe B : Spécifications
- 374 Annexe C : Informations de garantie
- 375 Annexe D : Réglementation
- 389 Annexe E : Contacts
- 391 Nederlands, Gebruikershandleiding
- 393 Hoofdstuk 1: Bekend raken met de Wireless-G- breedbandrouter
- 395 Hoofdstuk 2: Het aansluiten van de Wireless-G- breedbandrouter
- 398 Hoofdstuk 3: De Wireless-G-breedbandrouter configureren
- 424 Bijlage A: Probleemoplossing
- 436 Bijlage B: Specificaties
- 437 Bijlage C: Informatie over garantie
- 438 Bijlage D: Informatie over regelgeving
- 452 Bijlage E: Contactgegevens