- No category
advertisement
PR-C101_C101M_E.book Page 8 Monday, August 27, 2007 11:16 AM
Full Color Card Printer
PR-C101/C101M
Basic Card Printing Methods
This section explains the basic flow of operations, from turning on the power through printing a card.
Turning On and Off the Printer
Turn on the printer before starting to print.
Before turning on the power, make sure the following preparations are complete:
• The Ink Ribbon Cartridge is loaded
• The Card Case is loaded
• The cards are loaded
• The Front Cover is closed
• The printer is connected to the computer
• The printer driver is installed z
If the preparations above have not been performed, follow the instructions in the "Easy Setup Guide".
1
Press the Power Switch to turn on the power.
• Press "–" on the Power Switch behind of the printer for turning on the power.
• After [Initializing..] appears on the LCD Panel, the operating indicator turns blue and [Ready to Print] appears.
• Press "O" on the Power Switch for turning off the power.
Note
z
If a card is still in the printer when the power is turned off, it is ejected from Card
Ejection Slot 1 (default setting).
z
If the ERROR Indicator turns red, refer to "Troubleshooting" on page 36.
8
advertisement
Related manuals
advertisement
Table of contents
- 3 Operating the Printer Safely
- 5 Part Names and Descriptions
- 5 Front of the Printer
- 6 Rear of the Printer
- 7 Front Cover
- 8 Operation Panel
- 10 Basic Card Printing Methods
- 10 Turning On and Off the Printer
- 11 Loading Cards
- 11 Loading Cards into the Card Case
- 12 Manually Loading Cards One by One
- 13 Printing
- 14 Removing Cards
- 15 Changing the Ink Ribbon Cartridge
- 15 When a Change is Necessary
- 15 Changing the Cartridge
- 17 Normal Mode and User Mode
- 17 Normal Mode
- 17 User Mode
- 18 Switching to User Mode
- 19 Basic User Mode Operations
- 19 Moving to the Next Menu (Switching to Menus on the Same Level)
- 19 Moving to a Sub-menu (Switching to Menus on a Lower Level)
- 20 Returning to the Main Menu (Switching to Menus on a Higher Level)
- 20 Switching to Normal Mode (Exiting User Mode)
- 21 Getting the Most Out of Your Printer
- 21 Reprinting a Card that Has Just Been Printed
- 22 Counting the Number of Cards that Are Printed
- 22 Displaying the Total Number of Sides that Are Printed
- 23 Switching the Card Ejection Slot
- 24 Checking the Ink Ribbon Remaining in the Ink Ribbon Cartridge
- 25 Checking the Ink Ribbon Cartridge that is Currently Installed
- 26 Adjusting the Print Quality
- 26 Adjusting the Color
- 28 Adjusting the Edges of Images
- 29 Turning the Error Alarm On or Off
- 30 Setting the Printer to Reprint a Card if an Error Occurs
- 31 Checking the Program Information and Serial Number
- 32 Changing the Magnetic Encoder's Settings (PR-C101M Only)
- 32 Returning Settings to the Default
- 33 Preventing Theft and Unauthorized Usage
- 33 Preventing Theft of the Printer (Security Cable Slot)
- 33 How to Store Cards (Removing the Card Case)
- 34 Cleaning
- 34 Before Cleaning
- 34 Cleaning with a Cleaning Card
- 36 Cleaning the Cleaning Roller
- 37 Cleaning the Feeding Roller
- 38 Troubleshooting
- 38 When an Error Message Appears
- 38 Clearing an Error
- 38 How to Clear an Error
- 41 When a Card is Jammed
- 42 When Cards are Not Printed Correctly
- 43 Other Troubles
- 43 When These Solutions Don't Work
- 44 Appendix
- 44 Consumables
- 44 Ink Ribbon Cartridges
- 45 Cards
- 45 Cleaning Cards
- 45 Updating the Printer's Software
- 46 Menu Route Map (User Mode)
- 48 Main Specifications