- No category
advertisement
PR-C101_C101M_E.book Page 30 Monday, August 27, 2007 11:16 AM
Full Color Card Printer
PR-C101/C101M
Changing the Magnetic Encoder's Settings (PR-C101M Only)
You can switch the coercivity (Hi-Co or Lo-Co) when writing magnetic data.
Note
z
You can also change the setting by using the printer driver. (
→See "Opening the
Printer Driver Settings Screen" on page 47.)
1
Switch from Normal Mode to User
Mode.
→See "Switching to User Mode" on page 16 for details on how to switch to User Mode.
Ready to Print
MENU
(3 Sec.)
CLEAR
User Mode >>
EXE
[User Mode]
2
Press the Menu Key until [Printer
Setup >>] appears, and then press the
EXE Key.
[User Mode]
MENU
MENU
Printer Setup >>
EXE
[Printer Setup]
3
Press the Menu Key until [Encode
Type] appears, and then press the EXE
Key.
• Pressing the EXE Key switches between [LOCO] and
[HICO].
[Printer Setup]
MENU
MENU
Encode Type LOCO
EXE
Encode Type HICO
Returning Settings to the Default
You can restore changed settings to their initial factory default settings.
The following settings can be returned to their initial settings.
• [Card Count] value (the [Total Count] value cannot be initialized).
• Settings on the sub menus in [Printer Setup].
• Settings on the sub menus in [Image Setup].
30
advertisement
Related manuals
advertisement
Table of contents
- 3 Operating the Printer Safely
- 5 Part Names and Descriptions
- 5 Front of the Printer
- 6 Rear of the Printer
- 7 Front Cover
- 8 Operation Panel
- 10 Basic Card Printing Methods
- 10 Turning On and Off the Printer
- 11 Loading Cards
- 11 Loading Cards into the Card Case
- 12 Manually Loading Cards One by One
- 13 Printing
- 14 Removing Cards
- 15 Changing the Ink Ribbon Cartridge
- 15 When a Change is Necessary
- 15 Changing the Cartridge
- 17 Normal Mode and User Mode
- 17 Normal Mode
- 17 User Mode
- 18 Switching to User Mode
- 19 Basic User Mode Operations
- 19 Moving to the Next Menu (Switching to Menus on the Same Level)
- 19 Moving to a Sub-menu (Switching to Menus on a Lower Level)
- 20 Returning to the Main Menu (Switching to Menus on a Higher Level)
- 20 Switching to Normal Mode (Exiting User Mode)
- 21 Getting the Most Out of Your Printer
- 21 Reprinting a Card that Has Just Been Printed
- 22 Counting the Number of Cards that Are Printed
- 22 Displaying the Total Number of Sides that Are Printed
- 23 Switching the Card Ejection Slot
- 24 Checking the Ink Ribbon Remaining in the Ink Ribbon Cartridge
- 25 Checking the Ink Ribbon Cartridge that is Currently Installed
- 26 Adjusting the Print Quality
- 26 Adjusting the Color
- 28 Adjusting the Edges of Images
- 29 Turning the Error Alarm On or Off
- 30 Setting the Printer to Reprint a Card if an Error Occurs
- 31 Checking the Program Information and Serial Number
- 32 Changing the Magnetic Encoder's Settings (PR-C101M Only)
- 32 Returning Settings to the Default
- 33 Preventing Theft and Unauthorized Usage
- 33 Preventing Theft of the Printer (Security Cable Slot)
- 33 How to Store Cards (Removing the Card Case)
- 34 Cleaning
- 34 Before Cleaning
- 34 Cleaning with a Cleaning Card
- 36 Cleaning the Cleaning Roller
- 37 Cleaning the Feeding Roller
- 38 Troubleshooting
- 38 When an Error Message Appears
- 38 Clearing an Error
- 38 How to Clear an Error
- 41 When a Card is Jammed
- 42 When Cards are Not Printed Correctly
- 43 Other Troubles
- 43 When These Solutions Don't Work
- 44 Appendix
- 44 Consumables
- 44 Ink Ribbon Cartridges
- 45 Cards
- 45 Cleaning Cards
- 45 Updating the Printer's Software
- 46 Menu Route Map (User Mode)
- 48 Main Specifications