- No category
advertisement
PR-C101_C101M_E.book Page 15 Monday, August 27, 2007 11:16 AM
Normal Mode and User Mode
Normal Mode and User Mode
You can switch the printer from Normal Mode to User Mode while it is operating.
This section provides an outline of both modes, explains how to change modes and explains the basic operations of the User Mode.
Normal Mode and User Mode
Normal Mode
Normal Mode is used for printing cards.
When the power is turned on the printer starts in
Normal Mode.
The printer's status, such as [Ready to Print] or
[Card Empty], appears on the LCD Panel.
User Mode
User Mode is used to set operations and check the status of the printer.
To switch to the User Mode from the Normal
Mode, hold down the Menu Key for more than three seconds and then press the EXE Key.
→See "Switching to User Mode" on page 16 for details on how to switch modes.
A list of menus, such as [Card Count] and [Color
Adjust] are displayed on the LCD Panel.
15
advertisement
Related manuals
advertisement
Table of contents
- 3 Operating the Printer Safely
- 5 Part Names and Descriptions
- 5 Front of the Printer
- 6 Rear of the Printer
- 7 Front Cover
- 8 Operation Panel
- 10 Basic Card Printing Methods
- 10 Turning On and Off the Printer
- 11 Loading Cards
- 11 Loading Cards into the Card Case
- 12 Manually Loading Cards One by One
- 13 Printing
- 14 Removing Cards
- 15 Changing the Ink Ribbon Cartridge
- 15 When a Change is Necessary
- 15 Changing the Cartridge
- 17 Normal Mode and User Mode
- 17 Normal Mode
- 17 User Mode
- 18 Switching to User Mode
- 19 Basic User Mode Operations
- 19 Moving to the Next Menu (Switching to Menus on the Same Level)
- 19 Moving to a Sub-menu (Switching to Menus on a Lower Level)
- 20 Returning to the Main Menu (Switching to Menus on a Higher Level)
- 20 Switching to Normal Mode (Exiting User Mode)
- 21 Getting the Most Out of Your Printer
- 21 Reprinting a Card that Has Just Been Printed
- 22 Counting the Number of Cards that Are Printed
- 22 Displaying the Total Number of Sides that Are Printed
- 23 Switching the Card Ejection Slot
- 24 Checking the Ink Ribbon Remaining in the Ink Ribbon Cartridge
- 25 Checking the Ink Ribbon Cartridge that is Currently Installed
- 26 Adjusting the Print Quality
- 26 Adjusting the Color
- 28 Adjusting the Edges of Images
- 29 Turning the Error Alarm On or Off
- 30 Setting the Printer to Reprint a Card if an Error Occurs
- 31 Checking the Program Information and Serial Number
- 32 Changing the Magnetic Encoder's Settings (PR-C101M Only)
- 32 Returning Settings to the Default
- 33 Preventing Theft and Unauthorized Usage
- 33 Preventing Theft of the Printer (Security Cable Slot)
- 33 How to Store Cards (Removing the Card Case)
- 34 Cleaning
- 34 Before Cleaning
- 34 Cleaning with a Cleaning Card
- 36 Cleaning the Cleaning Roller
- 37 Cleaning the Feeding Roller
- 38 Troubleshooting
- 38 When an Error Message Appears
- 38 Clearing an Error
- 38 How to Clear an Error
- 41 When a Card is Jammed
- 42 When Cards are Not Printed Correctly
- 43 Other Troubles
- 43 When These Solutions Don't Work
- 44 Appendix
- 44 Consumables
- 44 Ink Ribbon Cartridges
- 45 Cards
- 45 Cleaning Cards
- 45 Updating the Printer's Software
- 46 Menu Route Map (User Mode)
- 48 Main Specifications