Installation and User s Guide

11

SunTouch Main Status Screen (Pool/Spa mode - Shared Equipment)

Use the SunTouch display to view daily pool and spa operations. The “Schedule” menu feature (page 17) is typically used for these operations. For manual spa operation, pressing the SPA Up button will activate the spa circuit, switch on the filter pump, display the current spa water, air temperature setting, and heat source. To activate the pool circuit and activate the filter pump, display the current pool water and air temperature, and heat source, set the menu feature “Circuit On/Off” to “ON.” If the AUX 1 (Down arrow) button is assigned to a light circuit, use this button to manually switch the lights on/off. Lights and other installed equipment are setup from the

“Circuit Function” menu (page 26). Before using the SunTouch system, familiarize yourself with the status screen and control buttons.

®

SPA 75°F / 85°F

Spa button: Switch the spa on and off and display current temperature settings. Press this button to activate the filter pump and rotate the valves and circulate pool water to the spa. To enable heat for the spa when this circuit is switched on, either switch on the heat source or switch on “Manual

Heat” from the “Heat” menu.

11:51AM HEATER

AUX 1 button: Press this button to manually switch on the AUX 1 relay (number 1 is displayed). AUX 1 can be assign to operate accessory equipment such as pool and spa lights.

Lower current set point temperature setting

Raise current set point temperature setting

11: 51AM AUX 1

air temperature via the air sensor located near the pool area. To display the air temperature setting, the air sensor must be enabled

(see “Advanced” menu, page 24). The main status screen toggles between the pool, spa and air temperature settings. Degree units are displayed in either Fahrenheit or Celsius. If the top display line displays “SunTouch”, no spa or pool function is active and air sensor is not enabled.

Note: For information about

HI-TEMP (UP arrow button)

circuit controls for single body systems, see page 39.

HEATER: Displays the heat source (Heater, Solar Prf., Solar) being used as specified in the “Heat” menu settings (see page

14). If heat is enabled, when the pool filter pump is switch on, the heat source is displayed.

75° F / 85° F: Displays the actual spa or pool water temperature

(75° F) and the set point temperature (85° F) as set in the

“Heater” menu (see page 14). To adjust set temperature setting use the (-) TEMP and (+) TEMP buttons.

Time: Displays the SunTouch system time as set in the “Clock” menu setting (see page 19).

freeze protection is active (see page 26).

AIR 77°F

AUX 1 2 3: Displays AUX 1, 2, 3 (lower line) switched on. Press the AUX 1 (1) button to manually switch auxiliary 1 on or off. AUX 2, and AUX 3 can be switched on and off manually from the “Circuit On/Off” menu (page 13). Auxiliary functions are assign in the “Circ. Function” menu (page 26).

spa water temperature settings. If the pool filter pump is switched on from the “Circuit On/Off” menu or a programmed schedule, “POOL” is displayed with the current pool water temperature settings. “SPA” and

“POOL” are displayed alternatively if both are active. The filter pump will switch off while the pool/spa valves are rotating into position.

For information about

HI-TEMP/LO-TEMP controls for this button (single body system) see page 39.

11: 51AM AUX D

pump switches on. See “Circuit Functions Menu” (page 26) for more information.

(AUX 1,2,3) is in “delay” mode. For example, if AUX 2 is assigned to a cleaner, when the auxiliary circuit 2 is switched on via the “Circuit On/Off” menu setting, this will force the filter pump on for five (5) minutes before the cleaner

SunTouch Solar, Pool and Spa Control System Installation and User’s Guide