- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- User manual
advertisement
44
SunTouch System Overview
QuickTouch (QT4)
Wireless remote kit
(P/N 520148)
(Optional)
Temperature Sensors
(Water, Air and Solar)
• Pumps
Filter, Cleaner, Spa Jet -
1.5 HP 120 VAC
3 HP 277 VAC
20 FLA/120 LRA,120 VAC
17 FLA/102 LRA, 277 VAC
• Pool/Spa Lights
1.5 KW 120 VAC Tungsten
4.8 KW 240 VAC Tungsten
20 AMP, 277 VAC Ballast
• Pool/Spa Valve
Suction and return.
24 VAC valve actuator, shared equipment only
• Valve actuators
Valve A (intake), Valve B
(return), Valve C (Solar)
• Heat Source
Gas, Electric and Solar
• Relays (3 maximum
installed in power center)
25 AMP, 277 VAC
Optional equipment
SunTouch enclosure (with two resettable circuit breakers
(18 VAC and 24 VAC).
Electrical Ratings:
Input:
120/240 VAC, 60/50 Hz,
820/410 mA maximum.
Output:
120 VAC, 20 FLA/120 LRA,
1.5 HP.
277 VAC, 17 FLA/120 LRA,
3.0 HP.
20 AMP Tungsten, 50/60 Hz.
• IntelliChlor Salt Chlorine
Generator (SCG)
• IC20 P/N 520554/520556
• IC40 P/N 520555/520556
• Power Center
P/N 520556
• IntelliFlo VS (P/N 011013)
IntelliFlo VF (P/N 011012)
(see page 30)
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
SunTouch Power Center
(Front View)
Enclosure front door
Low voltage push-button circuit breakers
(18 VAC / 24 VAC)
Control Panel LCD and buttons
1” Grommet for low voltage wires
(Air and water temperature sensors, motorized valves)
Two ½" and one ¾"conduit knockout for high voltage wires
SunTouch Power Center (Front View)
(14” H x 12” W x 4¾” D)
Mounting bracket (x3)
Front panel handle
Spring latch
Retaining screw
45
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Section 1: SunTouch Pool and Spa Control System Overview
- 9 SunTouch Control System Overview
- 9 SunTouch Solar Mode
- 9 SunTouch Pool/Spa Mode
- 10 SunTouch Control Panel
- 10 SunTouch Control Buttons
- 12 SunTouch Main Status Screen (Solar Only mode)
- 12 SunTouch Solar Only System
- 13 Operating SunTouch in Solar Only Mode
- 13 Setting up SunTouch for Solar Only mode from Pool/Spa mode
- 14 Adjusting the water temperature setting (Solar Only mode)
- 14 Solar Only Menus
- 14 Set Temperature
- 15 System Control
- 15 System Mode
- 15 Time Set
- 16 Start and Stop Temp Differentials
- 16 Solar Freeze protection
- 16 Cleaner Freeze protection
- 16 Air sensor
- 17 Freeze Protection in Solar Only mode
- 17 Operating SunTouch in Pool/Spa mode (Shared Equipment)
- 17 Setting up SunTouch to Operate in Pool/Spa mode
- 17 Adjusting the water temperature setting in Pool/Spa mode
- 18 Selecting the heat source
- 19 SunTouch Main Status Screen (Pool/Spa mode - Shared Equipment)
- 20 Pool/Spa Mode Menus (Shared Equipment)
- 21 Pool/Spa Mode Menus
- 21 Circuit On/Off Menu (1/14)
- 22 Heat Menu (2/14)
- 22 Pool Temperature and Heat Source settings
- 23 Spa Temperature and Heat Source
- 23 HI-TEMP /LO-TEMP (Pool or Spa) Control Button
- 23 Manual Heat (Off/On)
- 24 Delay Cancel Menu (3/14)
- 25 Schedules Menu (4/14)
- 26 Schedule your Spa or Pool
- 26 Edit an existing program
- 26 Delete a program
- 27 Clock Menu (5/14)
- 27 Solar Menu (6/14)
- 29 Valves Menu (7/14)
- 30 Advanced Menu (8/14): Heater and Valve Delays
- 30 Advanced Menu (8/14): Temp Units - F° / C° (Fahrenheit/Celsius)
- 31 Advanced Menu (8/14): Calibrate water, air and solar sensors
- 32 Advanced Menu (8/14): Air Sensor Enable/Disable
- 32 Advanced Menu (8/14): System Mode
- 32 Advanced Menu (8/14): System Type
- 32 Advanced Menu (8/14): Circuit Time Out
- 33 Advanced Menu (8/14): Reset Factory
- 33 Diagnostics Menu (9/14): Firmware Rev
- 33 Diagnostics Menu: Solar Temp
- 33 Diagnostics Menu: Self Test
- 33 Diagnostics Menu: IntelliChem
- 34 Circuit Functions Menu (10/14)
- 34 Assigning Circuit Functions
- 34 Freeze Protection
- 34 Circuit Functions
- 35 Preset Circuit Functions
- 36 Settings Menu (11/14): QuickTouch (QT4) Wireless Remote
- 36 Assign QT4 buttons
- 36 Pump Menu (12/14)
- 36 Single speed filter pump
- 37 Two-speed filter pump
- 38 IntelliFlo VS pump
- 38 Freeze Protection
- 40 IntelliFlo VF pump
- 43 IntelliFlo VSF+SVRS pump
- 44 IntelliChlor Menu (13/14)
- 44 IntelliChlor Menu (13/14): Status and Error Messages
- 46 Service Menu (14/14): Service, Timeout, Auto
- 47 SunTouch Main Status Screen (Pool/Spa Mode - Single Body System)
- 48 High/Low Temperature Circuit Control (Single Body System)
- 48 HI-TEMP / LO-TEMP Circuit Controls
- 48 Setting up SunTouch to operate as a Single Body system
- 49 Pool/Spa Mode (Single Body of Water) Menus
- 50 Section 2: Installation and Setup
- 50 SunTouch System Installation Steps Summary
- 50 Required Tools
- 51 SunTouch Solar Package Contents
- 51 SunTouch Control System Contents
- 51 Replacement Parts
- 51 Optional Equipment
- 52 SunTouch System Overview
- 54 Plumbing Requirements
- 55 Equipment Location
- 56 Solar Hydraulics System
- 57 SunTouch Power Center High Voltage Connections
- 57 SunTouch Power Center Location
- 58 Grounding and Bonding to the SunTouch Power Center
- 59 Preparing the SunTouch Power Center
- 59 Opening the front panel
- 60 Mounting the SunTouch Power Center
- 61 Removing Electrical Conduit Knockouts
- 62 Installing Conduit and Wire to the SunTouch Power Center
- 63 Transformer Connections
- 63 High Voltage Wiring
- 64 SunTouch Motherboard Connections
- 64 Equipment Power
- 65 Accessing the SunTouch Motherboard
- 66 Installing Auxiliary Relays
- 66 Relay locations
- 66 Installing relays
- 68 Installing Valve Actuators
- 68 Adjusting the valve position
- 69 Installing and Connecting Temperature Sensors
- 69 Water Temperature Sensor
- 69 Ambient Air Temperature Sensor (for freeze protection)
- 69 Solar Temperature Sensor
- 70 Connecting SunTouch to a Gas Heater
- 70 Connecting to a standard heater
- 70 Connecting to a MiniMax®, MasterTemp® Gas Heater
- 71 Connecting to a Sta-Rite® Gas Heater
- 71 Connecting a Standard Heat Pump or Electric Heater
- 72 SunTouch Solar System Installation
- 72 SunTouch Solar System Start-Up
- 72 Pool Cleaner Protection
- 73 SunTouch Pool/Spa Controller System Start-Up
- 73 Check Electronics
- 73 SunTouch System Test
- 73 Testing the auxiliary relays
- 74 Setting up the SunTouch system for the first time (after equipment Installation)
- 76 Section 3: Troubleshooting
- 76 Frequently Asked Questions (FAQ)
- 76 How do I setup a two-speed pump?
- 76 Can I switch the heater on and change the temperature from the spa?
- 76 How do I switch on solar heating?
- 77 SunTouch Error Messages
- 77 Error Messages
- 77 Self Test Error Codes
- 77 Error Code Table
- 77 Resetting the System Fuses
- 78 Problem Solving a Solar System
- 78 SunTouch solar is not operating
- 78 Water flow to panels switch does not operate the valve actuator
- 78 Checking The Temperature Sensors
- 78 Testing the Solar System
- 78 Air Sensor Error
- 79 Temperature vs. Resistance Data
- 80 IntelliChlor Error Messages
- 80 System Problem Diagnosis
- 81 Problem: The Quick Touch remote will not work, or will not work dependably
- 82 IntelliFlo Warning and Alarm Conditions
- 82 Alarm and warning LED sequence
- 82 SunTouch Specifications
- 83 Wiring SunTouch to the IntelliChlor Salt Chlorine Generator
- 84 Wiring IntellilChlor (SCG) and Standard Pump to SunTouch
- 85 Pump to SunTouch
- 86 Appendix
- 86 Emergency Shut-Off switch (ESO3)
- 86 Location
- 87 Installing the (ESO3) Circuit Board
- 89 Commercial Application using ESO3 and SunTouch (Single Body System)
- 90 Glossary
- 91 Delay Cancel
- 91 Schedules
- 91 Clock
- 91 Valves
- 91 Advanced
- 91 Diagnostics
- 91 QuickTouch
- 91 Pumps
- 91 IntelliChlor
- 91 Service