- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- User manual
advertisement
32
Pump Menu (12/14)
(Continued)
IntelliFlo
®
VF pump
From the IntelliFlo VF menu you can assign circuits to control the pump flow rate (GPM), priming, also filter, backwashing, vacuum functions and view the current pump status. For more information about the IntelliFlo
VS, refer to the IntelliFlo VF Installation and User’s Guide (P/N 350075).
To assign up eight (8) pump speeds and circuits for the IntelliFlo VS pump:
Main Menu 12/14
Pumps
Pump Type
[INTELLIFLO VF ]
Pumps Parameters
Menu: CIRC. SETUP
Assign Flows
1 - GPM: 80
Circuit Setup
1 - [ POOL ]
Menu button: Select the Pumps 12/14 menu.
Right button: Press the button to view the type of pump to select.
Up/Down buttons: Select IntelliFlo VF them press Right button again to select.
Press Up/Down buttons to view the Pump Parameters menus: CIRC. SETUP,
FILT. CIRC., FILTER, PRIMING, BACKWASH, VACUUM and STATUS.
Press Right button to choose one of the parameters.
Press the Right button again to ASSIGN FLOWS (GPM) setting.
Press Up/Down buttons set the pump flow rate (15 - 130 GPM).
Press Right button to CIRCUIT SETUP for the pump. Press Up/Down buttons to view the circuits for the first of eight (8) pump circuits: [NONE, SPA, POOL,
AUX 1, AUX 2, AUX 3, FEATURE 1-4, SOLAR, HEATER, POOL HEAT,
SPA HEAT, FREEZE, POOL/SPA, and SOLAR/HT (solar/heater)].
Press Right button to select the circuit. Note: Selecting “Pool/Spa” or
“Solar/HT” combines several circuits into the same pump speed for pool and spa or for solar and heater combination systems. Normally this would require programming two separate pump speeds for each function. Using one of these selections, free-up one of the four pump speed for other uses.
Press Right button to continue to assign pump FILT. CIRC. and CIRCUITS. You can assign up to eight (8) pump speeds and circuits.
Pumps Parameters
Menu: FILTER
When finished assigning pump flow rate and circuits, press the Right button until
FLOWS is displayed, then press the Up/Down buttons and select FILTER.
Filter Params
Size: 25000
Filter Params
Turns: 2
Filter Params
Man Filt: 30
Press Right button to select Filter Params Time. Press the Up/Down buttons to set the Filter Size (1000 to 255000 gallons).
Press Right button to select Filter Params Manual Filter. Press the Up/Down
buttons to set the Filter Size (15 - 130).
When finished, Press Right button to select Filter Params Turns. Press the Up/
Down buttons to set the number of pool cycle turns (1-4).
When finished assigning filter parameters, press the Right button until FLOWS is displayed, then press the Up/Down buttons and select FILTER.
Press Right button to select Filter Params Time. Press the Up/Down buttons to set the Filter Size (1000 to 255000 gallons).
Press Right button to select Filter Params Manual Filter. Press the Up/Down
buttons to set the Filter Size (15 - 130).
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Pump Menu (12/14)
(Continued)
IntelliFlo
®
VF pump
(Continued)
Assigning an IntelliFlo VF 3050 Pump Address
Before assigning a pump address in the SunTouch for IntelliFlo VF, first set the address on the pump itself.
If there is only one pump, it is always seen as pump #1 by SunTouch. In this case you do not need to set the pump address. When using multiple IntelliFlo pumps with SunTouch assign an address to each pump. The address can be set to #1, #2. The address set at the pump must match the IntelliFlo pump number selected in the SunTouch PUMPS > PUMP TYPE > menus.
Note: IntelliFlo VF 3050 pumps cannot be connected in series with other pumps.
Check valves must be used when a pump is used in parallel with other pumps.
To assign an IntelliFlo VF 3050 pump address:
1. Press the Start/Stop button to stop the pump. Be sure that the green power LED is on and the pump is stopped.
2. Press the Menu button.
3. Press the Up and Down arrow buttons to scroll through the menu items. Press the Select button to access the “Pool Data” menu.
4. Press the Select button to access the “Pump Address” setting.
5. Press the Select button to change the current pump address.
6. To enter the new address number, press the Left and Right arrows to select which digit to modify, then use the Up and Down arrows to change the selected digit.
7. When you are done assigning the pump address number, press the Enter button to save the changes. To cancel any changes, press the Escape button to exit edit mode without saving.
33
NOTE: INTELLIFLO “FREEZE” PROTECTION - If the IntelliFlo pump is on due to a freeze condition (not switch on from a relay circuit state), and if a freeze speed/flow is set in IntelliTouch, this setting takes priority even if the previous setting is lower than the default circuit speed. If no “freeze” protection is set, the pump will be forced on at the default circuit speed/flow. Any programmed or manual operation that actually switches on a circuit, will cause the pump to run at that speed if it is higher.
NOTE: INTELLIFLO IN “SERVICE MODE” - The IntelliFlo pump will STOP when SunTouch is in ‘Service” mode.
NOTE: INTELLIFLO VF PUMPS - If the IntelliFlo VF pump is just starting (requiring a prime) and SOLAR is available, solar will be delayed for five (5) minutes to allow the pump to prime. This only applies for IntelliFlo pump(s) assigned as to a “pool” pump.
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
34
Pump Menu (12/14)
(Continued)
IntelliFlo
®
VF pump
Pumps Parameters
Menu: PRIMING
Priming Params
Max Flow: 55
Priming Params
Max Time: 5
Priming Params
Sys Time: 1
When finished, Press Right button three times until FILTER is displayed.
Press the Up/Down buttons to select PRIMING.
Press the Right button to select Priming Params: Max Flow.
Press the Up/Down buttons to select the maximum flow GPM rate (15-130).
Press the Right button to select the Max Time, press the Up/Down buttons to select the maximum time from 1 to 15 minutes.
Press the Right button to select the Sys Time, press the Up/Down buttons to select the maximum time from 1 to 15 minutes.
Pumps Parameters
Menu: BACKWASH
Backwash Params
Clean Filt: 10
Priming Params
Flow GPM: 60
Priming Params
Duration: 5
Priming Params
Rinse Time: 5
When finished assigning filter parameters, press the Right button until PRIMING is displayed, then press the Up/Down buttons to select BACKWASH.
Press Right button to select Backwash Params Clean Filt:
Press the Up/Down buttons to set the filter clean time (1-50 minutes).
Press Right button to select Flow GPM. Press the Up/Down buttons to set the flow rate (15-130 GPM).
Press Right button to select Duration. Press the Up/Down buttons to set the duration (1-60 minutes).
Press Right button to select Rinse Time. Press the Up/Down buttons to set the rinse time (1-60 minutes).
Pumps Parameters
Menu: VACUUM
Vacuum Params
Flow (gpm): 65
Vacuum Params
Time (min): 30
When finished assigning filter parameters, press the Right button until
BACKWASH is displayed, then press the Up/Down buttons to select VACUUM.
Press Right button to select Vacuum Params Flow (gpm): Press the Up/Down
buttons to set the gpm flow rate (15-130 GPM).
Press Right button to select Flow GPM. Press the Up/Down buttons to set the flow rate (15-130 GPM).
Press Right button to select Time (min). Press the Up/Down buttons to set the vacuum time (1-600 minutes).
Press Right button to select Rinse Time. Press the Up/Down buttons to set the rinse time (1-60 minutes).
Pumps Parameters
Menu: STATUS
RPM: 1500 75 W
GPM: 50
Filter: 0
Status: NORMAL
When finished assigning vacuum parameters, press the Right button until
VACUUM is displayed, then press the Up/Down buttons to select STATUS.
Press Right button to view the current RPM, WATTS and GPM status.
Press the Right button again to view the Filter and pump operation status.
Pumps Parameters
Menu: FILT. CIRC
Filter Circuit
[ POOL ]
When finished assigning vacuum parameters, press the Right button until STATUS is displayed, then press the Up/Down buttons to select FILT. CIRC.
Press Right button to view the filter circuits. Press the Up/Down buttons to select the circuit: (NONE, SPA, POOL, AUX 1, AUX 2, AUX 3).
Left button: Press the Left button to return to the main status screen.
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
advertisement
Related manuals
advertisement
Table of contents
- 9 Section 1: SunTouch Pool and Spa Control System Overview
- 9 SunTouch Control System Overview
- 9 SunTouch Solar Mode
- 9 SunTouch Pool/Spa Mode
- 10 SunTouch Control Panel
- 10 SunTouch Control Buttons
- 12 SunTouch Main Status Screen (Solar Only mode)
- 12 SunTouch Solar Only System
- 13 Operating SunTouch in Solar Only Mode
- 13 Setting up SunTouch for Solar Only mode from Pool/Spa mode
- 14 Adjusting the water temperature setting (Solar Only mode)
- 14 Solar Only Menus
- 14 Set Temperature
- 15 System Control
- 15 System Mode
- 15 Time Set
- 16 Start and Stop Temp Differentials
- 16 Solar Freeze protection
- 16 Cleaner Freeze protection
- 16 Air sensor
- 17 Freeze Protection in Solar Only mode
- 17 Operating SunTouch in Pool/Spa mode (Shared Equipment)
- 17 Setting up SunTouch to Operate in Pool/Spa mode
- 17 Adjusting the water temperature setting in Pool/Spa mode
- 18 Selecting the heat source
- 19 SunTouch Main Status Screen (Pool/Spa mode - Shared Equipment)
- 20 Pool/Spa Mode Menus (Shared Equipment)
- 21 Pool/Spa Mode Menus
- 21 Circuit On/Off Menu (1/14)
- 22 Heat Menu (2/14)
- 22 Pool Temperature and Heat Source settings
- 23 Spa Temperature and Heat Source
- 23 HI-TEMP /LO-TEMP (Pool or Spa) Control Button
- 23 Manual Heat (Off/On)
- 24 Delay Cancel Menu (3/14)
- 25 Schedules Menu (4/14)
- 26 Schedule your Spa or Pool
- 26 Edit an existing program
- 26 Delete a program
- 27 Clock Menu (5/14)
- 27 Solar Menu (6/14)
- 29 Valves Menu (7/14)
- 30 Advanced Menu (8/14): Heater and Valve Delays
- 30 Advanced Menu (8/14): Temp Units - F° / C° (Fahrenheit/Celsius)
- 31 Advanced Menu (8/14): Calibrate water, air and solar sensors
- 32 Advanced Menu (8/14): Air Sensor Enable/Disable
- 32 Advanced Menu (8/14): System Mode
- 32 Advanced Menu (8/14): System Type
- 32 Advanced Menu (8/14): Circuit Time Out
- 33 Advanced Menu (8/14): Reset Factory
- 33 Diagnostics Menu (9/14): Firmware Rev
- 33 Diagnostics Menu: Solar Temp
- 33 Diagnostics Menu: Self Test
- 33 Diagnostics Menu: IntelliChem
- 34 Circuit Functions Menu (10/14)
- 34 Assigning Circuit Functions
- 34 Freeze Protection
- 34 Circuit Functions
- 35 Preset Circuit Functions
- 36 Settings Menu (11/14): QuickTouch (QT4) Wireless Remote
- 36 Assign QT4 buttons
- 36 Pump Menu (12/14)
- 36 Single speed filter pump
- 37 Two-speed filter pump
- 38 IntelliFlo VS pump
- 38 Freeze Protection
- 40 IntelliFlo VF pump
- 43 IntelliFlo VSF+SVRS pump
- 44 IntelliChlor Menu (13/14)
- 44 IntelliChlor Menu (13/14): Status and Error Messages
- 46 Service Menu (14/14): Service, Timeout, Auto
- 47 SunTouch Main Status Screen (Pool/Spa Mode - Single Body System)
- 48 High/Low Temperature Circuit Control (Single Body System)
- 48 HI-TEMP / LO-TEMP Circuit Controls
- 48 Setting up SunTouch to operate as a Single Body system
- 49 Pool/Spa Mode (Single Body of Water) Menus
- 50 Section 2: Installation and Setup
- 50 SunTouch System Installation Steps Summary
- 50 Required Tools
- 51 SunTouch Solar Package Contents
- 51 SunTouch Control System Contents
- 51 Replacement Parts
- 51 Optional Equipment
- 52 SunTouch System Overview
- 54 Plumbing Requirements
- 55 Equipment Location
- 56 Solar Hydraulics System
- 57 SunTouch Power Center High Voltage Connections
- 57 SunTouch Power Center Location
- 58 Grounding and Bonding to the SunTouch Power Center
- 59 Preparing the SunTouch Power Center
- 59 Opening the front panel
- 60 Mounting the SunTouch Power Center
- 61 Removing Electrical Conduit Knockouts
- 62 Installing Conduit and Wire to the SunTouch Power Center
- 63 Transformer Connections
- 63 High Voltage Wiring
- 64 SunTouch Motherboard Connections
- 64 Equipment Power
- 65 Accessing the SunTouch Motherboard
- 66 Installing Auxiliary Relays
- 66 Relay locations
- 66 Installing relays
- 68 Installing Valve Actuators
- 68 Adjusting the valve position
- 69 Installing and Connecting Temperature Sensors
- 69 Water Temperature Sensor
- 69 Ambient Air Temperature Sensor (for freeze protection)
- 69 Solar Temperature Sensor
- 70 Connecting SunTouch to a Gas Heater
- 70 Connecting to a standard heater
- 70 Connecting to a MiniMax®, MasterTemp® Gas Heater
- 71 Connecting to a Sta-Rite® Gas Heater
- 71 Connecting a Standard Heat Pump or Electric Heater
- 72 SunTouch Solar System Installation
- 72 SunTouch Solar System Start-Up
- 72 Pool Cleaner Protection
- 73 SunTouch Pool/Spa Controller System Start-Up
- 73 Check Electronics
- 73 SunTouch System Test
- 73 Testing the auxiliary relays
- 74 Setting up the SunTouch system for the first time (after equipment Installation)
- 76 Section 3: Troubleshooting
- 76 Frequently Asked Questions (FAQ)
- 76 How do I setup a two-speed pump?
- 76 Can I switch the heater on and change the temperature from the spa?
- 76 How do I switch on solar heating?
- 77 SunTouch Error Messages
- 77 Error Messages
- 77 Self Test Error Codes
- 77 Error Code Table
- 77 Resetting the System Fuses
- 78 Problem Solving a Solar System
- 78 SunTouch solar is not operating
- 78 Water flow to panels switch does not operate the valve actuator
- 78 Checking The Temperature Sensors
- 78 Testing the Solar System
- 78 Air Sensor Error
- 79 Temperature vs. Resistance Data
- 80 IntelliChlor Error Messages
- 80 System Problem Diagnosis
- 81 Problem: The Quick Touch remote will not work, or will not work dependably
- 82 IntelliFlo Warning and Alarm Conditions
- 82 Alarm and warning LED sequence
- 82 SunTouch Specifications
- 83 Wiring SunTouch to the IntelliChlor Salt Chlorine Generator
- 84 Wiring IntellilChlor (SCG) and Standard Pump to SunTouch
- 85 Pump to SunTouch
- 86 Appendix
- 86 Emergency Shut-Off switch (ESO3)
- 86 Location
- 87 Installing the (ESO3) Circuit Board
- 89 Commercial Application using ESO3 and SunTouch (Single Body System)
- 90 Glossary
- 91 Delay Cancel
- 91 Schedules
- 91 Clock
- 91 Valves
- 91 Advanced
- 91 Diagnostics
- 91 QuickTouch
- 91 Pumps
- 91 IntelliChlor
- 91 Service