- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- User manual
advertisement
Heat Menu (2/14)
(Continued)
Spa Temperature and Heat Source
To set the SPA temperature and switch the HEATER ON or OFF:
Main Menu 2/14
Heat
Spa Temperature
Temp: 85°F
Spa Heat Source
Heat: Heater
Menu > Right arrow button: Select the Heat settings.
Right/Left arrow button: Select the SPA temperature setting.
Up/Down arrow button: Adjust to the desired spa set point temperature
(from 40° F to 104° F or 4° C to 40° C).
Right arrow button: Access the POOL HEAT source setting.
Up/Down arrow button: Select the heat source options: OFF, HEATER, SOLAR
PREFERRED or SOLAR.
Left arrow button: Press the Left button to return to the main status screen.
HI-TEMP (Up Arrow button)
For SunTouch single body systems (pool only or spa only, see page 36), the HI-TEMP (UP arrow button) is used to switch the heater (regardless of the Heat menu setting) and filter pump on and off. Typically this circuit is used with the “Manual Heat” feature (see below) for on-demand spa water heat. The heat temperature settings are displayed on the main screen. The heater is active when the set temperature is higher than the water temperature. The heater will switch off when the water temperature rises above the set temperature.
LO-TEMP (Spa) Menu Operation
The LO-TEMP on and off control is made from the Heat menu setting. For SunTouch single body systems
(pool only or spa only, see page 36), the LO-TEMP menu setting is used to switch on and off the heat source and filter pump. A heat selection must be selected in the Heat menu before the heater is activated. The
“Manual Heat” setting does not function with the LO-TEMP circuit. The heater is active when the set temperature is higher than the water temperature. The heater will switch off when the water temperature rises above the set temperature.
MANUAL HEAT (Off/On)
By default, the spa Manual Heat feature is always set to “ON.” This allows the spa to begin to heat whenever the SPA, Up arrow button is pressed, regardless of the heat source setting in the Heat menu (see page 4).
This feature allows the spa to be filtered daily with the heater switched off. The optional QuickTouch QT4 wireless remote can also be used to switch the spa heater on. This feature will not work for solar systems, only gas and electric heaters.
MANUAL HEAT
To enable or disable spa heat when switched on manually:
Main Menu 2/14
Heat
Manual Heat
Manual Heat: On
Menu > Right arrow button: Select the Heat settings.
Right/Left arrow button: Select the MANUAL HEAT setting.
Up/Down arrow button: Select OFF to disable or ON to automatically activate the heat when the SPA, Up arrow button (or HI-TEMP button for single body systems) is pressed regardless of the “Heat Source” setting (see page 14).
Left arrow button: Press the Left arrow button to return to the main status screen.
15
SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
advertisement
Related manuals
advertisement
Table of contents
- 9 Section 1: SunTouch Pool and Spa Control System Overview
- 9 SunTouch Control System Overview
- 9 SunTouch Solar Mode
- 9 SunTouch Pool/Spa Mode
- 10 SunTouch Control Panel
- 10 SunTouch Control Buttons
- 12 SunTouch Main Status Screen (Solar Only mode)
- 12 SunTouch Solar Only System
- 13 Operating SunTouch in Solar Only Mode
- 13 Setting up SunTouch for Solar Only mode from Pool/Spa mode
- 14 Adjusting the water temperature setting (Solar Only mode)
- 14 Solar Only Menus
- 14 Set Temperature
- 15 System Control
- 15 System Mode
- 15 Time Set
- 16 Start and Stop Temp Differentials
- 16 Solar Freeze protection
- 16 Cleaner Freeze protection
- 16 Air sensor
- 17 Freeze Protection in Solar Only mode
- 17 Operating SunTouch in Pool/Spa mode (Shared Equipment)
- 17 Setting up SunTouch to Operate in Pool/Spa mode
- 17 Adjusting the water temperature setting in Pool/Spa mode
- 18 Selecting the heat source
- 19 SunTouch Main Status Screen (Pool/Spa mode - Shared Equipment)
- 20 Pool/Spa Mode Menus (Shared Equipment)
- 21 Pool/Spa Mode Menus
- 21 Circuit On/Off Menu (1/14)
- 22 Heat Menu (2/14)
- 22 Pool Temperature and Heat Source settings
- 23 Spa Temperature and Heat Source
- 23 HI-TEMP /LO-TEMP (Pool or Spa) Control Button
- 23 Manual Heat (Off/On)
- 24 Delay Cancel Menu (3/14)
- 25 Schedules Menu (4/14)
- 26 Schedule your Spa or Pool
- 26 Edit an existing program
- 26 Delete a program
- 27 Clock Menu (5/14)
- 27 Solar Menu (6/14)
- 29 Valves Menu (7/14)
- 30 Advanced Menu (8/14): Heater and Valve Delays
- 30 Advanced Menu (8/14): Temp Units - F° / C° (Fahrenheit/Celsius)
- 31 Advanced Menu (8/14): Calibrate water, air and solar sensors
- 32 Advanced Menu (8/14): Air Sensor Enable/Disable
- 32 Advanced Menu (8/14): System Mode
- 32 Advanced Menu (8/14): System Type
- 32 Advanced Menu (8/14): Circuit Time Out
- 33 Advanced Menu (8/14): Reset Factory
- 33 Diagnostics Menu (9/14): Firmware Rev
- 33 Diagnostics Menu: Solar Temp
- 33 Diagnostics Menu: Self Test
- 33 Diagnostics Menu: IntelliChem
- 34 Circuit Functions Menu (10/14)
- 34 Assigning Circuit Functions
- 34 Freeze Protection
- 34 Circuit Functions
- 35 Preset Circuit Functions
- 36 Settings Menu (11/14): QuickTouch (QT4) Wireless Remote
- 36 Assign QT4 buttons
- 36 Pump Menu (12/14)
- 36 Single speed filter pump
- 37 Two-speed filter pump
- 38 IntelliFlo VS pump
- 38 Freeze Protection
- 40 IntelliFlo VF pump
- 43 IntelliFlo VSF+SVRS pump
- 44 IntelliChlor Menu (13/14)
- 44 IntelliChlor Menu (13/14): Status and Error Messages
- 46 Service Menu (14/14): Service, Timeout, Auto
- 47 SunTouch Main Status Screen (Pool/Spa Mode - Single Body System)
- 48 High/Low Temperature Circuit Control (Single Body System)
- 48 HI-TEMP / LO-TEMP Circuit Controls
- 48 Setting up SunTouch to operate as a Single Body system
- 49 Pool/Spa Mode (Single Body of Water) Menus
- 50 Section 2: Installation and Setup
- 50 SunTouch System Installation Steps Summary
- 50 Required Tools
- 51 SunTouch Solar Package Contents
- 51 SunTouch Control System Contents
- 51 Replacement Parts
- 51 Optional Equipment
- 52 SunTouch System Overview
- 54 Plumbing Requirements
- 55 Equipment Location
- 56 Solar Hydraulics System
- 57 SunTouch Power Center High Voltage Connections
- 57 SunTouch Power Center Location
- 58 Grounding and Bonding to the SunTouch Power Center
- 59 Preparing the SunTouch Power Center
- 59 Opening the front panel
- 60 Mounting the SunTouch Power Center
- 61 Removing Electrical Conduit Knockouts
- 62 Installing Conduit and Wire to the SunTouch Power Center
- 63 Transformer Connections
- 63 High Voltage Wiring
- 64 SunTouch Motherboard Connections
- 64 Equipment Power
- 65 Accessing the SunTouch Motherboard
- 66 Installing Auxiliary Relays
- 66 Relay locations
- 66 Installing relays
- 68 Installing Valve Actuators
- 68 Adjusting the valve position
- 69 Installing and Connecting Temperature Sensors
- 69 Water Temperature Sensor
- 69 Ambient Air Temperature Sensor (for freeze protection)
- 69 Solar Temperature Sensor
- 70 Connecting SunTouch to a Gas Heater
- 70 Connecting to a standard heater
- 70 Connecting to a MiniMax®, MasterTemp® Gas Heater
- 71 Connecting to a Sta-Rite® Gas Heater
- 71 Connecting a Standard Heat Pump or Electric Heater
- 72 SunTouch Solar System Installation
- 72 SunTouch Solar System Start-Up
- 72 Pool Cleaner Protection
- 73 SunTouch Pool/Spa Controller System Start-Up
- 73 Check Electronics
- 73 SunTouch System Test
- 73 Testing the auxiliary relays
- 74 Setting up the SunTouch system for the first time (after equipment Installation)
- 76 Section 3: Troubleshooting
- 76 Frequently Asked Questions (FAQ)
- 76 How do I setup a two-speed pump?
- 76 Can I switch the heater on and change the temperature from the spa?
- 76 How do I switch on solar heating?
- 77 SunTouch Error Messages
- 77 Error Messages
- 77 Self Test Error Codes
- 77 Error Code Table
- 77 Resetting the System Fuses
- 78 Problem Solving a Solar System
- 78 SunTouch solar is not operating
- 78 Water flow to panels switch does not operate the valve actuator
- 78 Checking The Temperature Sensors
- 78 Testing the Solar System
- 78 Air Sensor Error
- 79 Temperature vs. Resistance Data
- 80 IntelliChlor Error Messages
- 80 System Problem Diagnosis
- 81 Problem: The Quick Touch remote will not work, or will not work dependably
- 82 IntelliFlo Warning and Alarm Conditions
- 82 Alarm and warning LED sequence
- 82 SunTouch Specifications
- 83 Wiring SunTouch to the IntelliChlor Salt Chlorine Generator
- 84 Wiring IntellilChlor (SCG) and Standard Pump to SunTouch
- 85 Pump to SunTouch
- 86 Appendix
- 86 Emergency Shut-Off switch (ESO3)
- 86 Location
- 87 Installing the (ESO3) Circuit Board
- 89 Commercial Application using ESO3 and SunTouch (Single Body System)
- 90 Glossary
- 91 Delay Cancel
- 91 Schedules
- 91 Clock
- 91 Valves
- 91 Advanced
- 91 Diagnostics
- 91 QuickTouch
- 91 Pumps
- 91 IntelliChlor
- 91 Service