Interface Specifications
Interface Specifications
Table 5 describes the interfaces for the WF-500 appliance.
Table 5. Interface Specifications
Specification Description
Ethernet ports
MGT port
Console port
USB ports
3 RJ-45 10/100/1000 Ethernet ports for network traffic. (Ports 2 and 3 are reserved for future use).
1 RJ-45 10/100/1000 Ethernet port used for device management and for data traffic.
1 DB-9 serial port for connecting a serial console. Use these settings:
• Data rate: 9600
• Data bits: 8
• Parity: none
• Stop bits: 1
• Flow control: none
4 USB ports reserved for future use.
Electrical Specifications
Table 6 lists the electrical specifications for the WF-500 appliance.
Table 6. Electrical Specifications
Specification
Maximum internal power dissipation
AC voltage
Description
1200W
100-240 VAC
Environmental Specifications
Table 7 lists the environmental specifications for the WF-500 appliance.
Table 7. Environmental Specifications
Specification Description
Operating temperature range 5° to 35° C
Storage temperature range
System air flow
-20° to 65° C
Front to rear
Operating humidity
Storage humidity
10% to 80% non-condensing
5% to 95% non-condensing
24 • Specifications Palo Alto Networks
Chapter 5
Compliance Statements
This section provides the compliance statement for the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI), which governs radio frequency emissions in Japan.
The following information is in accordance to VCCI Class A requirements:
Translation: This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective actions.
Palo Alto Networks Compliance Statements • 25
26 • Compliance Statements Palo Alto Networks
Appendix A
General Safety Information
CAUTION
Please Note the Following:
•
The WF-500 appliance should not be used in a home, school or other public area where the general population would have access to it.
WARNING
To prevent the potential for personal injury, property damage, or death, please observe the following instructions:
•
Do not use damaged equipment, including exposed, frayed or damaged power cords. Use only the approved power cable that is rated for the equipment. The voltage and current rating of the cable should be greater than the ratings marked on the equipment.
•
Plug the power cables into properly grounded electrical outlets. Do not use adapter plugs or
remove the grounding prong from a cable.
•
Observe extension cable and power strip ratings to ensure that the total ampere rating of all equipment plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip.
•
The power supplies in the WF-500 appliance may produce high voltages and potential energy hazards. By opening the cover of the WF-500 appliance you may be exposed to a risk of electric shock. The components inside the WF-500 appliance housing should only be serviced by Palo Alto Networks.
•
The WF-500 appliance should not be operated with the cover removed.
•
Components inside the WF-500 appliance housing may become extremely hot during normal operation. These components include the memory and CPU modules.
•
The WF-500 appliance should not be operated in environments that can get wet. Protect the WF-500 appliance at all times from liquid intrusion.
•
If your WF-500 appliance gets wet, turn off the AC power at the circuit breaker before attempting to remove the power cables from the electrical outlet. Then disconnect power to the equipment and to any attached devices.
Palo Alto Networks • 27
28 •
•
Avoid obstructing the air vents on the WF-500 appliance or pushing objects into the openings. This could lead to fire or electric shock.
CAUTION
To prevent hardware damage or loss of data, observe the following precautions:
•
Follow installation instructions carefully.
•
Do not attempt to service the equipment yourself.
•
You should operate this equipment from the type of external power source indicated on the electrical ratings label.
•
Always leave at least 4 inches (10.2cm) of physical clearance on all vented sides of the
WF-500 appliance. This permits the airflow required for proper ventilation.
•
Avoid placing equipment too close together such that it is subject to re-circulated (preheated) air. Avoid placing equipment too close to an appliance or exhaust vent.
•
Ensure that cables are connected to the WF-500 appliance without stress and that nothing rests on the cables.
•
If the equipment is located in a rack, move it with caution. Ensure that all casters and/or stabilizers are firmly connected. While moving the equipment, avoid uneven surfaces and sudden stops.
•
Do not place other equipment, monitors, or other devices on top of the WF-500 appliance.
•
To protect the WF-500 appliance from fluctuations in electrical power, use a surge suppressor, line conditioner or uninterruptible power supply (UPS).
CAUTION
Please observe the following additional precautions for rack-mounted systems:
•
Slide rail mounted equipment is not to be used as a shelf or a work space.
•
Elevated Operating Ambient – If the WF-500 appliance is installed in a closed or multiunit rack assembly, the operating ambient temperature in the rack environment may be greater than the room ambient temperature. Therefore, consideration should be given to
the maximum operating temperature specified in “Environmental Specifications” on page 24.
•
Reduced Air Flow – Installation of the WF-500 appliance in a rack should be such that the amount of air flow required for safe operation is not compromised.
•
Mechanical Loading – Mounting of the WF-500 appliance in the rack should not create a hazardous condition from uneven mechanical loading.
•
Circuit Overloading – Connection of the equipment to the supply circuit should not create an overloaded situation. Pay close attention to equipment nameplate ratings.
Palo Alto Networks
