advertisement
Maintenance
Daily Maintenance (whenever using the stove) - Continued
Door Opening
Make sure the heater has fully cooled
(approximately 25 minutes) before opening the door and conducting service.
NOTE: Do not overtighten the pawl. This can permanently damage the latch and prematurely wear out the door gasket.
Phillips
Screwdriver
Bracket (attached to side of heater)
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
Door
Frame
Pawl
Lock Nut
When securing the door, make sure the pawl fits over the bracket before tightening.
With the pawl free of the bracket, the door may be swung open.
2 9
© Travis Industries
4080728
1 0 0 - 0 1 1 5 6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Introduction
- 2 Important Information
- 4 Safety Precautions
- 6 Heating Specifications
- 6 Dimensions
- 6 Electrical Specifications
- 6 EPA Compliance
- 7 Before You Begin
- 7 Packing List
- 7 Installation Options
- 7 Planning The Installation
- 7 Stove Placement
- 7 Floor Protection Requirements
- 8 Clearances - Straight Installation
- 8 Clearances - Corner Installation
- 9 Venting the Pellet Stove
- 9 Maximum Venting Distance
- 10 Pellet Vent Type
- 10 Installing the Pellet Vent
- 10 Pellet Vent Termination
- 11 Mobile Home Requirements
- 11 Outside Air (used for combustion)
- 12 Alcove Installation Requirements
- 12 Baffle Installation
- 12 Door Seal Verification
- 12 Restrictor Adjustment
- 13 Thermostat Installation
- 14 Installation
- 15 Installation Example: Interior Vertical Installation
- 16 Installation Example: Class A Chimney Retrofit
- 17 Installation Example: Masonry Fireplace Hearth Stove
- 19 Installation Example: Freestanding Masonry Chimney
- 20 Safety Notice
- 20 Location of Controls
- 20 Starting the Heater for the First Time
- 21 Loading Pellets
- 21 The Two Modes of Operation
- 22 Manual Mode
- 23 Auto Mode
- 24 Restrictor Adjustment
- 24 Adjusting the Fan Speed
- 25 Start-Up Sequence
- 25 "AUGER ON" Light
- 25 "Maintenance Required" Light
- 26 "MANUAL AUGER" Button
- 26 Power Outages
- 26 Using a Pellet/Corn Mix with This Heater
- 27 Daily Maintenance (whenever using the stove)
- 27 Inspect the Burn
- 27 Make Sure Pellets are Not Piling Up
- 28 Check Firepot for Clinkers
- 28 Cleaning the Firepot
- 29 Door Opening
- 30 Weekly Maintenance (or every 5 bags of pellets)
- 30 Flyash Removal
- 30 Clean the Hopper
- 30 Clean the Heat Exchange Tubes
- 31 Clean the Baffles
- 32 Sweep Ash Into Ashpan
- 33 Check Ashpan, Dispose if necessary
- 33 Clean the Glass
- 34 Yearly Maintenance (or every ton)
- 34 Clean the Vertical Exhaust Duct
- 35 Clean the Exhaust Blower
- 35 Clean the Vent
- 36 Door Seal
- 39 Normal Operating Sounds
- 40 Safety Label
- 41 Warranty
- 42 Index