- No category
advertisement
3.6.19 !No Macro defined!
No Macro defined for key, enter macro number followed by [Shift], followed by [Store], followed by key.
3.6.20 !Not In Record!
3.6.21 !No Tracks Armed!
Auto-Edit attempted with no tracks armed.
3.6.22 !No EEPROM Access!
EEprom not found during power-up, reset unit using small reset button or power on and off. If problem persists contact CB Electronics.
3.6.23 !Backup Machine!
Chase command may not be issued to the backup machine. See Setup|ADR/Auto|Options|Menu
89: Backup Machine
3.6.24 !Rec Out Disabled!
Record out disabled by Macro Key 75 (Enable Rec Out).
3.6.25 ! System in Local!
A remote command received and ignored on input A/E or F whist the System is in Local.
3.6.26 Command not Fitted
A remote command received that is not fitted to software.
3.6.27 Master Not in Play
Record command not sent to Backup machine because the master was not in play.
3.6.28 No Record Rehearse
Record command from user ignored because in Rehearse or review mode.
3.6.29 Mcn Record Assigned
3.6.30 !Use After Shift
Key only operates when Shift LED illuminated.
3.6.31 !Number Lock On!
RM-6 only, Machine commands locked out, [SHIFT] + [NUMBER] to enable/disable
3.6.32 ! Backup not Armed
Auto Record: The specified back-up machine is not armed.
3.6.33 Backup Local-Tape
Auto Record: The specified backup machine has no tape
3.6.34 Disabled in Record
This key/command is disabled by Setup|Root|Unit|record|Menu 15: Record Disable transport
Keys
CB Electronics SR/MR User Manual 30 July 2008 SR-User 21
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 SR-4 System Diagram
- 2 SR-3 System diagram
- 10 1.1 RM6-424 Connections
- 11 1.2 To Control individual machines
- 11 1.3 To Control multiple machines
- 11 1.3.1 Master Machine
- 11 1.3.2 Perfect Machine/Virtual Master
- 11 1.3.3 Slave/chase Machines
- 11 1.3.4 Offset
- 12 1.3.5 Difference
- 12 1.4 ONE FINGER TYPIST: STICKY KEYS
- 12 1.5 INSTALLING NEW SOFTWARE
- 12 1.6 RECORD ENABLE
- 12 1.6.1 CHECKING MACHINE RECORD ENABLE
- 12 1.6.2 CHANGING MACHINE RECORD ENABLE
- 12 1.6.3 REHEARSE
- 12 1.6.4 RECORD/EDIT ON
- 12 1.6.5 RECORD TRACK SELECT
- 12 1.6.6 VIDEO MACHINE ENABLE
- 12 1.6.7 RECORD INHIBIT
- 13 1.7 SWITCH 'A' on the SR-3 or 'E' on the SR
- 13 1.8 MASTER CHASE
- 13 1.9 MACHINE REFERENCE: VIDEO SYNCS or WORD-CLOCK
- 13 1.10 USING THE GENERATOR AS A MASTER
- 13 1.11 CRASH RECORD
- 13 1.12 USING THE SR-3 WITH A DAW
- 13 1.13 CONVERTING SR-4 -> SR
- 14 End Time
- 14 2.0 Multi-Machine Synchronizer Set Up
- 14 2.1 The SR-4 as a multi-machine synchroniser
- 14 2.2 SR-4 BLOCK / SR-3 BLOCK
- 14 2.2.1 SR-4 TIMECODE OUTPUT
- 15 2.2.2 SR-4 TIMECODE INPUT
- 15 2.3 Setting up the System
- 15 2.3.1 Defining the Master
- 15 2.3.2 Perfect Master Mode
- 15 2.3.3 Remote Master Mode
- 15 2.3.4 SR/MR Timecode Generator Output
- 16 2.3.5 Defining a Machine as a Slave
- 16 2.3.6 Displaying the Chase Group
- 16 2.3.7 Entering an Offset
- 16 2.3.8 Trimming an Offset
- 16 2.3.9 Entering a Negative Offset
- 16 2.3.10 Pre-Roll
- 16 2.3.11 Post-roll
- 16 2.3.12 Delay
- 17 3.0 DISPLAY
- 17 3.1 Master Display
- 17 3.2 Slave Display
- 17 3.3 Auto Record Display
- 17 3.4 Display Fields
- 17 3.4.1 STATUS INDICATOR
- 17 3.4.2 MACHINE NAME
- 17 3.4.3 POSITION
- 17 3.4.4 CURRENT KEYBOARD ENTRY
- 18 3.4.5 OFFSET/SHIFTER | Enable/Arm/Record
- 18 3.4.6 MESSAGE TO USER
- 19 3.4.7 RECORD BANK
- 19 3.5 SR-24 KEYBOARD DISPLAY
- 19 3.6 ERROR MESSAGES
- 19 3.6.1 Not Record Enabled
- 19 3.6.2 ! Record Inhibit !
- 19 3.6.3 !System Not Locked
- 19 3.6.4 ! Key Lock On !
- 19 3.6.5 ! OUT before IN !
- 19 3.6.6 ! Comms-Local-Tape
- 20 3.6.7 ! Macros Protected
- 20 3.6.8 ! No Track Mapped!
- 20 3.6.9 Master/Rec Enabled
- 20 3.6.10 !Locate to Start!
- 20 3.6.11 TC Jump or Pre-Rol
- 20 3.6.12 !Commands Disabled
- 20 3.6.13 !Video Not Stopped
- 20 3.6.14 !Alg & Vid Enable!
- 20 3.6.15 !Not all in Record
- 20 3.6.16 ! Crash Enabled !
- 20 3.6.17 ! No Tape !
- 20 3.6.18 !Macro Not Fitted!
- 21 3.6.19 !No Macro defined!
- 21 3.6.20 !Not In Record!
- 21 3.6.21 !No Tracks Armed!
- 21 3.6.22 !No EEPROM Access!
- 21 3.6.23 !Backup Machine!
- 21 3.6.24 !Rec Out Disabled!
- 21 3.6.25 ! System in Local!
- 21 3.6.26 Command not Fitted
- 21 3.6.27 Master Not in Play
- 21 3.6.28 No Record Rehearse
- 21 3.6.29 Mcn Record Assigned
- 21 3.6.30 !Use After Shift
- 21 3.6.31 !Number Lock On!
- 21 3.6.32 ! Backup not Armed
- 21 3.6.33 Backup Local-Tape
- 21 3.6.34 Disabled in Record
- 22 3.6.35 Fit 24C08 EEPROM
- 22 3.6.36 Reset to Factory
- 22 3.6.37 Reset to User
- 22 3.6.38 Port Not Available
- 22 3.6.39 ! Need Password !
- 22 3.6.40 ! MR Sys Not Used!
- 22 3.6.41 Set To Follow Mcn!
- 22 3.6.42 ! Serial Error !
- 22 3.6.43 ! Code Follow On !
- 22 3.6.44 ! Set PD-1 Port !
- 22 3.6.45 ! Use After Store!
- 23 4.0 KEYBOARD
- 23 4.1 SHIFT
- 23 4.2 STORE / RECALL / TRIM + / TRIM
- 24 4.3 TRIM+ and TRIM
- 24 4.4 RECALL-RECALL
- 24 4.5 Locate
- 24 4.6 INSTANT REPLAY
- 24 4.7 AGAIN
- 24 4.8 MARK
- 24 4.9 RECORD ENABLE GROUP
- 25 4.10 MASTER MACHINE
- 25 4.11 CHASE (SLAVE) MACHINE
- 25 4.12 RECORD TRACK ENABLES
- 26 4.13 RECORD BANK
- 26 4.14 PLAY
- 26 4.15 ID << and ID >>
- 26 4.16 RM-6/Video Slave [CMD] (originally [Number])
- 27 4.17 RM-6/Video Slave [Offset]
- 27 4.18 SR-4 Keyboard
- 27 5.0 AUTO RECORD/ADR/TAKER MODES
- 27 5.1 Auto Key
- 28 5.2 Rehearse Key
- 28 5.3 AUTO and REHEARSE OFF
- 28 5.4 Rehearse Mode
- 28 5.5 Auto-Record Mode
- 28 5.6 Manual Record Mode
- 29 5.7 Review Mode
- 29 5.8 NEXT LOOP
- 29 5.9 PREV LOOP
- 29 5.10 JUMP TO LOOP ???
- 29 5.11 JOIN LOOP
- 29 5.12 INSERT LOOP
- 29 5.13 DELETE LOOP
- 30 5.14 Cycle: Record Out Enable
- 30 5.15 Talent Cueing: CB VS-1 Streamer
- 30 5.16 BACKUP DAT
- 30 5.17 RECORD ADVANCE
- 30 5.18 Streamer/Wipe Trigger output
- 31 5.19 Beep output
- 32 6.0 MACRO KEYS
- 32 6.1 DEFINING A MACRO KEY
- 32 6.2 READING A MACRO KEY
- 32 6.3 Factory default MACRO KEYS
- 32 6.4 Some Useful Macro's
- 32 6.4.1 Shifter control :- Macro's 68, 69 and
- 33 6.4.2 Instant Record :- Macro
- 33 6.4.3 Auto Input Monitor :- Macro
- 33 6.4.4 Display Generator : Macro
- 33 6.4.5 Step Forward and Reverse : Macros
- 33 6.4.6 *2, *4, *6 Wind :- Macro's
- 33 6.4.7 Red light :- Macro
- 33 6.4.8 One Key Post Sync :- Macro
- 33 6.4.9 Loop:- Macro
- 34 7.0 OFFSET
- 34 7.1 DIRECT ENTRY OF OFFSETS
- 34 7.2 AUTO OFFSET CALCULATION
- 34 7.2.1 AUTO SLAVE
- 34 7.2.2 MARK SYNC
- 34 7.2.3 VIDEO EDITOR
- 34 7.3 TRIMMING THE OFFSET
- 34 7.4 ENTERING A NEGATIVE OFFSET
- 35 7.5 SUB-FRAME OFFSETS
- 35 7.6 CLEAR ALL OFFSETS
- 35 7.7 OFFSET CHANGE LOCKOUT WHEN RECORD ENABLED/MASTER
- 35 7.8 Shifter (Macro's on SR-4, SR-24 as standard)
- 35 7.9 Using the shifter to nudge offset's
- 36 7.10 The Colour Frame Key
- 36 7.11 Colour Trim
- 36 7.12 Mixed Code
- 36 7.12.1 Mixed Code & Offset
- 36 7.12.2 Mixed Code Passing through Zero/Midnight
- 36 7.13 Offset and Record In
- 39 8.0 Set-up
- 39 8.1 ROOT: Select Set-up Required
- 40 8.2 Unit Select Menu
- 40 8.3 Initial Record Command
- 40 8.4 Check for Lock Status
- 40 8.5 Offset change when Master or Record Enabled
- 40 8.6 Virtual Record Tally
- 41 8.7 Track Arm Keys
- 41 8.8 Record Track Arm
- 41 8.9 System Ready Length
- 41 8.10 Check for Record
- 42 8.11 SR-4/SR-424/RM-6: Global Record Command
- 42 8.12 Record-In & Record-Out Keys
- 42 8.13 Default Analogue & Video Record Ready
- 42 8.14 Default Record Enable
- 42 8.15 Record Disable Transport Keys
- 42 8.16 Mark record In
- 43 8.18 Wait for Slaves
- 43 8.19 Group Locates
- 43 8.20 Master When in Play
- 43 8.21 Stop Command
- 43 8.22 Timed Start Enable
- 44 UNIT TIMECODE
- 44 8.23 System Timecode Standard
- 44 8.24 Film Speed
- 44 8.25 Timecode Standard
- 44 8.26 Slave Tally Source
- 45 8.27 TC Reader -> Serial Port
- 45 8.28 Reader Incremental and direction test
- 45 8.29 System Frame Reference
- 45 8.30 Stationary Code
- 46 8.31 Macro Protection
- 46 8.31.1 Installing New Software
- 47 8.32 Input Ports
- 47 8.33 Locate with / without Preroll
- 47 8.34 GP Outputs
- 48 8.35 GP Output
- 49 8.36 Enable Auto-In when NOT Play
- 49 8.37 Setup Access
- 49 8.38 ID Key function
- 49 UNIT JOG
- 49 8.39 Jog Response
- 49 8.40 Jog Wheel
- 50 IFACE MENU