Motorola APX 7000L, ASTRO APX 7000 Series User Manual

Add to My manuals
106 Pages

advertisement

Motorola APX 7000L, ASTRO APX 7000 Series User Manual | Manualzz

APX6000XE_M1_FrontCover.fm Page 1 Wednesday, March 27, 2013 7:06 PM

APX™ TWO-WAY RADIOS

APX 6000XE

MODEL 1

USER GUIDE

APX_6000XE_M1.book Page 3 Saturday, November 2, 2013 5:40 AM m

ASTRO

®

APX™ 6000XE Series

Digital Portable Radios

Quick Reference Card

RF Energy Exposure and Product Safety

Guide for Portable Two-Way Radios

ATTENTION!

This radio is restricted to Occupational use only.

Before using the radio, read the RF Energy Exposure and Product Safety

Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and

Regulations.

Radio Controls

Top (Orange)

Button

__________

3-Position A/B/C Switch

__________________

Accessory

Connector

16-Position

Select Knob

__________

On/Off/Volume

Control Knob

Top Side (Select)

Button

__________

PTT

Button

Side Button 1

__________

Side Button 2

__________

Antenna

2-Position

Concentric Switch

______________

Top

Display

Microphone

Main

Speaker

Bluetooth

Pairing

Indicator

Battery

Radio On/Off

On

On/Off/Volume

knob clockwise.

Off

On/Off/Volume

knob counterclockwise.

Receiving and Transmitting

1

Select zone/channel.

2

Listen for a transmission.

OR

Press and hold

Volume Set

button.

OR

Press

Monitor

button and listen for activity.

3

Adjust volume, if necessary.

4

Press the

PTT

button to transmit; release to receive.

Sending an Emergency Alarm

1

Press and hold the

Emergency

button*.

2

The display shows

EMERGNCY

and the current zone/channel. A short, mediumpitched tone sounds, and the LED blinks red momentarily.

3

When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency.

* Default emergency button press timer is set to 1 second.

This timer is programmable, see page 33 in the user guide for details.

To exit emergency at any time, press and hold the

Emergency

button.

Zones and Channels

Zone

Zone

switch to desired zone.

Channel

Channel

switch to desired channel.

*PMLN5935E*

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011–2013 by Motorola Solutions, Inc. All Rights Reserved. 11/13.

1303 East Algonquin Road., Schaumburg, Illinois 60196, U.S.A.

PMLN5935E

English

APX_6000XE_M1.book Page 4 Saturday, November 2, 2013 5:40 AM

Sending an Emergency Call

1

Press the

Emergency

button.

2

Press and hold the

PTT

button. Speak clearly into the microphone.

3

Release the

PTT

button to end call.

4

Press and hold

Emergency

button to exit emergency.

To exit emergency at any time, press and hold the

Emergency

button.

Sending a Silent Emergency Call

1

Press the

Emergency

button.

2

The display does not change; the LED does not light up, and there is no tone.

3

Silent emergency continues until you:

Press and hold the

Emergency

button to exit emergency state.

OR

Press and release the

PTT

button to exit the

Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode.

To exit emergency at any time, press and hold the

Emergency

button.

Display Status Icons

U

V

Blinks when the battery is low.

The more stripes, the stronger the signal strength for the current site

(trunking only).

O j

Direct radio to radio communication or connected through a repeater.

On

= Direct

Off

= Repeater

M

H

OR

L

This channel is being monitored.

L

= Radio is set at Low power.

H

= Radio is set at High power.

i

Scanning a scan list.

Blinking dot

= Detects activity on the

Priority-One Channel during scan.

Steady dot

= Detects activity on the

Priority-Two Channel during scan.

k

The vote scan feature is enabled.

m

On

= Secure operation.

Off

= Clear operation.

Blinking

= Receiving an encrypted voice call.

On steady

= View mode

Blinking

= Program mode

A

or

B

or

C

Basic Zone Bank 1

A

= Radio is in Zone 1.

B

= Radio is in Zone 2.

C

= Radio is in Zone 3.

D

or

E

or

F

Basic Zone Bank 2

D

= Radio is in Zone 4.

E

= Radio is in Zone 5.

F

= Radio is in Zone 6.

A

,

B

,

C

... ...

x

or

y

Enhanced Zone Bank

A

= Contains Zone 1, Zone 2 and Zone

3,

B

= Contains Zone 4, Zone 5 and Zone

6,

C

= Contains Zone 7, Zone 8 and Zone

9,

.

.

.

X

= Contains Zone 70, Zone 71 and

Zone 72,

Y

= Contains Zone 73, Zone 74 and

Zone 75. b a

Bluetooth is ready.

Bluetooth is connected to the device.

English

Contents

Declaration of Conformity......................... 6

Important Safety Information..........8

Software Version..............................9

Notice to Users (FCC and Industry

Canada)......................................................9

Consignes de sécurité importantes.................................10

Version logicielle........................... 11

Avis aux utilisateurs (FCC et Industrie

Canada)....................................................11

Computer Software Copyrights....12

Documentation Copyrights...........13

Disclaimer.......................................14

Getting Started............................... 15

How to Use This Guide..................................15

Notations Used in This Manual......................15

Additional Performance Enhancement.......... 15

ASTRO 25 Enhanced Data.................15

Dynamic System Resilience (DSR).... 15

CrossTalk Prevention..........................16

Encrypted Integrated Data (EID).........16

SecureNet...........................................16

Conventional Talkgroup and Radio

Scan Enhancements......................16

What Your Dealer/System Administrator

Can Tell You.............................................17

Preparing Your Radio for Use.......18

Charging the Battery......................................18

Attaching the Battery..................................... 18

1

English

2

English

Attaching the Antenna................................... 19

Removing and Attaching the Accessory

Connector Cover...................................... 20

Attaching the Belt Clip................................... 21

Turning On the Radio.................................... 21

Adjusting the Volume.....................................22

Identifying Radio Controls............ 24

Radio Parts and Controls...............................24

Programmable Features................................25

Assignable Radio Functions............... 25

Assignable Settings or Utility

Functions....................................... 28

Accessing the Preprogrammed Functions.....28

Push-To-Talk (PTT) Button............................28

Identifying Status Indicators.........30

Status Icons...................................................30

LED Indicator.................................................32

Intelligent Lighting Indicators......................... 33

Alert Tones.................................................... 35

General Radio Operation...............39

Selecting a Zone............................................39

Selecting a Radio Channel............................ 39

Receiving and Responding to a Radio Call... 39

Receiving and Responding to a

Talkgroup Call................................39

Receiving and Responding to a

Private Call (Trunking Only)...........40

Receiving and Responding to a

Telephone Call (Trunking Only).....40

Making a Radio Call.......................................41

Making a Talkgroup Call..................... 41

Switching Between Repeater or Direct

Operation Button...................................... 42

Monitor Feature............................................. 42

Monitoring a Channel..........................42

Monitoring Conventional Mode........... 42

Advanced Features........................44

Advanced Call Features................................ 44

Selective Call (ASTRO

Conventional Only)........................ 44

Responding to the Dynamic

Regrouping Feature (Trunking

Only).............................................. 44

Scan Lists...................................................... 45

Viewing a Scan List.............................46

Viewing and Changing the Priority

Status.............................................46

Scan...............................................................46

Turning Scan On or Off.......................46

Making a Dynamic Priority Change

(Conventional Scan Only)..............46

Deleting a Nuisance Channel............. 47

Restoring a Nuisance Channel........... 47

Call Alert Paging............................................47

Receiving a Call Alert Page................ 48

Emergency Operation....................................48

Sending an Emergency Alarm............ 49

Sending an Emergency Call

(Trunking Only).............................. 49

Sending an Emergency Alarm with

Emergency Call............................. 50

Sending a Silent Emergency Alarm.... 50

Change of Channels during

Emergency.....................................51

Emergency Keep-Alive Feature.......... 51

Fireground (Conventional Only).....................51

Entering Fireground Zone Channel.....52

Responding to Evacuation Indicator... 53

Tactical Public Safety(TPS) (Conventional

Only)......................................................... 53

Using TPS Normal Transmission........53

Using TPS Emergency

Transmission................................. 54

Man Down......................................................54

Pre-Alert Timer....................................56

Post-Alert Timer.................................. 56

Radio Alerts When Man Down

Feature is Triggered...................... 56

Triggering Emergency.........................56

Radio Alerts When Man Down

Enhanced is Triggered...................57

Exiting Man Down Feature..................57

Re-Initiating Man Down.......................58

Testing the Man Down Feature...........58

Secure Operations.........................................58

Selecting Secure Transmissions.........58

Selecting Clear Transmissions........... 59

Managing Encryption.......................... 59

Global Positioning System (GPS)..................62

GPS Operation....................................62

GPS Performance Enhancement........63

Peer-Location on the Display

(ASTRO Conventional only).......... 63

Trunking System Controls............................. 64

Using the Failsoft System................... 64

Out-of-Range Radio............................65

Site Trunking Feature......................... 65

Locking and Unlocking a Site..............65

3

English

4

English

Site Display and Search Button.......... 65

Mission Critical Wireless - Bluetooth

®

-.......... 66

Turning the Bluetooth On....................66

Turning the Bluetooth Off....................67

Re-Pair Timer......................................67

Bluetooth Drop Timer..........................68

Pairing with Low Frequency-

Motorola Proximity Pairing (LF-

MPP) Feature................................ 69

Radio Indications of Lost Bluetooth

Connection.....................................70

Standard Pairing Feature....................70

Turning On the Bluetooth Audio

(Routing the Audio from the

Radio to the Headset)....................72

Turning Off the Bluetooth Audio

(Routing the Audio from the

Headset to the Radio)....................73

Adjusting the Volume of the Radio from Bluetooth Audio Device......... 73

Clearing All Bluetooth Devices

Information.....................................73

Programming Over Project 25 (POP 25)

(ASTRO 25 and ASTRO Conventional)... 73

Voice Announcement.....................................74

Site Selectable Alerts (ASTRO 25)................75

Utilities........................................................... 75

Using the Flip Display......................... 75

Selecting a Basic Zone Bank..............75

Selecting an Enhanced Zone Bank.... 76

Selecting the Power Level.................. 76

Controlling the Display Backlight........ 77

Locking and Unlocking the Controls... 77

Turning Voice Mute On or Off............. 77

Using the Time-Out Timer...................78

Using Conventional Squelch

Operation Features........................78

Using the PL Defeat Feature.............. 79

Digital PTT ID Support........................ 79

Smart PTT Feature (Conventional

Only).............................................. 79

Transmit Inhibit................................... 80

Helpful Tips.................................... 82

Radio Care.....................................................82

Cleaning Your Radio...........................83

Proper Ways to Handle the Radio...... 83

Radio Service and Repair...................83

Battery Care...................................................84

Battery Charge Status.........................84

Battery Recycling and Disposal.......... 85

Accessories....................................86

Maritime Radio Use in the VHF

Frequency Range....................... 87

Special Channel Assignments.......................87

Emergency Channel........................... 87

Non-Commercial Call Channel........... 87

Operating Frequency Requirements..............87

Declaration of Compliance for the Use of

Distress and Safety Frequencies..............90

Technical Parameters for Interfacing

External Data Sources..............................90

Glossary..........................................91

Limited Warranty............................96

MOTOROLA COMMUNICATION

PRODUCTS............................................. 96

I. WHAT THIS WARRANTY COVERS

AND FOR HOW LONG:........................... 96

II. GENERAL PROVISIONS:......................... 97

III. STATE LAW RIGHTS:..............................97

IV. HOW TO GET WARRANTY SERVICE:...97

V. WHAT THIS WARRANTY DOES NOT

COVER:....................................................98

VI. PATENT AND SOFTWARE

PROVISIONS:.......................................... 98

VII. GOVERNING LAW:...............................100

VIII. For Australia Only:................................100

English

5

Declaration of Conformity

This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.

Declaration of Conformity

Per FCC CFR 47 Part 2 Section 2.1077(a)

6

English

Responsible Party

Name: Motorola Solutions, Inc.

Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.

Phone Number: 1-800-927-2744

Hereby declares that the product:

Model Name:

APX 6000XE

conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)

Class B Digital Device

As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1

This device may not cause harmful interference, and

2

This device must accept any interference received, including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

English

7

8

Important Safety Information

RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios

ATTENTION!

This radio is restricted to Occupational use only.

Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way

Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations.

For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website:

http://www.motorolasolutions.com/APX

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

English

This radio transmitter has been approved by Industry

Canada to operate with Motorola-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated.

Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Software Version

All the features described in the following sections are supported by the radio's software version

R13.00.00

or later.

See

Accessing the Radio Information

to determine your radio software version.

Check with your dealer or system administrator for more details of all the features supported.

Notice to Users (FCC and Industry Canada)

This device complies with Part 15 of the FCC rules and RSS 210 of the Industry Canada rules per the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

• Changes or modifications made to this device, not expressly approved by Motorola, could void the user's authority to operate this equipment.

English

9

10

Consignes de sécurité importantes

Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit

ATTENTION!

Cette radio ne doit être utilisée qu'à des fins professionnelles.

Avant d'utiliser la radio, lisez le guide Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit, qui contient d'importantes instructions de fonctionnement pour une utilisation sécuritaire et des informations sur l'exposition aux fréquences radioélectriques, dans le but d’assurer votre conformité aux normes et règlements en vigueur.

Visitez le site Web suivant pour obtenir la liste des antennes, des batteries et des autres accessoires approuvés par Motorola :

http://www.motorolasolutions.com/APX

Selon la réglementation d'Industrie Canada, cet

émetteur radio ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada pour cet

émetteur. Afin de limiter les interférences radio pour

Français

(Canada)

les autres utilisateurs, le type et le gain de l'antenne doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) ne soit pas plus forte qu'il ne le faut pour établir la communication.

Cet émetteur radio a été approuvé par Industrie

Canada pour utilisation avec une antenne approuvée par Motorola offrant le gain maximal autorisé et l'impédance requise pour le type d'antenne indiqué. Il est strictement interdit d'utiliser avec cet appareil tout type d'antenne ne figurant pas dans cette liste et présentant un gain supérieur au maximum indiqué pour le type.

Version logicielle

Toutes les fonctions décrites dans les sections suivantes sont prises en charge par la version

R13.00.00

ou les versions ultérieures du logiciel de la radio.

Pour obtenir davantage de renseignements à propos des fonctions prises en charge, adressez-vous à votre détaillant ou à votre administrateur de système.

Avis aux utilisateurs (FCC et Industrie

Canada)

Cet appareil est conforme à la Partie 15 des règlements de la FCC et RSS 210 du règlement d'Industrie Canada selon les conditions énumérées ci-dessous:

• Ce dispositif ne doit pas causer d'interférences nuisibles.

• Cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent perturber le fonctionnement.

• Les changements ou les modifications apportées

à ce dispositif, non expressément approuvées par

Motorola, peuvent annuler le droit de l'utilisateur à utiliser cet équipement.

Français

(Canada)

11

Computer Software Copyrights

The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media.

Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.

Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of

Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal nonexclusive license to use that arises by operation of law in the sale of a product.

12

English

Documentation Copyrights

No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of

Motorola.

English

13

Disclaimer

The information in this document is carefully examined, and is believed to be entirely reliable.

However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others.

14

English

Getting Started

How to Use This Guide

This User Guide covers the basic operation of the

APX Portables.

However, your dealer or system administrator may have customized your radio for your specific needs.

Check with your dealer or system administrator for more information.

Notations Used in This Manual

Throughout the text in this publication, you will notice the use of

Warning

,

Caution

, and

Note

. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.

Warning:

An operational procedure, practice, or condition and so on, which may result in injury or death if not carefully observed.

Caution:

An operational procedure, practice, or condition and so on, which may result in damage to the equipment if not carefully observed.

Note:

An operational procedure, practice, or condition and so on, which is essential to emphasize.

Additional Performance Enhancement

The following performance enhancements are some of the latest creations designed to enhance the security, quality and efficiency of the radios.

ASTRO 25 Enhanced Data

ASTRO 25 Enhanced Data is optimized to handle different message sizes and variable update rates from different applications of the radio. Add Enhanced

Data to the Integrated Data system with a software installation to improve data channel efficiency and enable denser network traffic.

Dynamic System Resilience (DSR)

DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV&D) or data centric are all supported by

DSR.

15

English

16

CrossTalk Prevention

This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the

Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk.

Encrypted Integrated Data (EID)

EID provides security encryption and authentication of IV&D data bearer service communication between the radio and the Customer Enterprise Network.

SecureNet

SecureNet allows user to perform secured communications on an Analog or Motorola Data

Communication (MDC) channel. The MDC Over-the-

Air Rekeying (OTAR) feature will allow users to perform OTAR activities on an MDC channel.

Conventional Talkgroup and Radio Scan

Enhancements

A few enhancements have been made to the

Conventional Talkgroup at the system. These

English enhancements improve the Scan feature operation significantly when multiple agencies are using a single conventional radio frequency channel. These enhancements allow users to use Selective Squelch to operate on only the subset of talkgroups that are relevant to the users rather than all talkgroups on the channel. These Scan improvements have been made to eliminate the audio holes that were present and to turn on the busy LED when activity is present on the channel. Mixed Vote Scan and Standard

Conventional Scan configurations are supported.

Priority Operation is also supported.

Up to 30 different talkgroups can be supported using conventional channels. A maximum of four talkgroups can be supported when Vote Scan channels are being used.

Smart PTT is supported with this enhancement as

Smart PTT prevents users from transmitting while other users are on the channel.

Note:

User Selectable Talkgroups are not compatible with this Conventional Talkgroup Enhancement.

What Your Dealer/System Administrator Can

Tell You

Check with your dealer or system administrator for the correct radio settings, if the radio is to be operated in extreme temperatures (less than -30 °C or more than +60 °C), to ensure proper top and front display operation.

You can consult your dealer or system administrator about the following:

• Is your radio programmed with any preset conventional channels?

• Which buttons have been programmed to access other features?

• What optional accessories may suit your needs?

English

17

Preparing Your Radio for Use

This section provides simple instructions to prepare your radio for use.

18

Charging the Battery

Warning:

To avoid a possible explosion:

• Do

not

replace the battery in any area labeled

hazardous atmosphere

.

• Do

not

discard batteries in a fire.

The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of

Motorola-authorized batteries and chargers available for use with your radio, see

Accessories

on page

86.

Note:

When charging a battery attached to a radio, turn the radio off to ensure a full charge.

To charge the battery, place the battery (with or without the radio) in a Motorola-approved charger.

The LED on the charger indicates the charging progress; see the charger user guide.

Attaching the Battery

If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal.

Check with your dealer or system administrator for more information.

1

Slide the battery into the radio frame until the side latches click into place.

English

2

To remove the battery, squeeze the release latches at the bottom of the battery until the battery releases from the radio and remove the battery from the radio.

Note:

When removing the battery, ensure that the radio is turned off.

1

Set the antenna in its receptacle.

2

Turn the antenna clockwise to attach to the radio.

A

Attaching the Antenna

Ensure the radio is turned off before attaching the antenna.

3

To remove the antenna, turn the antenna counterclockwise.

Note:

When removing the antenna, ensure that the radio is turned off.

English

19

Removing and Attaching the Accessory

Connector Cover

The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio.

Note:

To prevent damage to the connector, shield it with the connector cover when not in use.

1

To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio.

Note:

If the thumbscrew is too tight, use an Allen wrench at to loosen it first.

A

B

C

2

Rotate and lift the connector cover to disengage it from the radio.

3

To attach the accessory connector cover, insert the hooked end of the cover into the slot above the connector.

4

Press downward on the cover’s top to seat it in the slot.

5

Once in place, tighten by rotating the thumbscrew

clockwise by hand.

20

English

Attaching the Belt Clip

1

Align the grooves of the belt clip with those of the radio and press upward until you hear a click to attach the belt clip.

2

Use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip downward and away from the radio to remove the clip.

Turning On the Radio

1

Rotate the

On/Off/Volume Control Knob

clockwise until you hear a click.

English

21

2

To turn off the radio, rotate the

On/Off/Volume

Control Knob

counterclockwise until you hear a click.

22

English

• If the power-up test is successful, you see momentary

SELFTEST

on the radio display, followed by the Home screen.

• If the power-up test is unsuccessful, you see

ERROR XX/YY

(

XX/YY

is an alphanumeric code).

Note:

If the radio fails to power-up after repeating a few times, record the

ERROR XX/YY code and contact your dealer.

Adjusting the Volume

Ensure the radio is power on and the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises.

1

To increase the volume, rotate the On/Off/Volume

Control Knob clockwise.

A

2

To decrease the volume, rotate this knob counterclockwise.

English

23

Identifying Radio Controls

Radio Parts and Controls

1

4

5

2

6

3

7

8

24

English

9

10

11

12

13

14

8

3

4

1

2

18

19

Antenna

Top (Orange) Button

[1]

Accessory Connector

16–Position Select Knob

[1]

15

16

17

7

8

5

6

On/Off/Volume Control Knob

3–Position A/B/C Switch

Belt Clip

Battery Latch

[1]

9 LED

10 2–Position Concentric Switch

[1]

11 Top Side (Select) Button

[1]

12 Push-to-Talk (PTT) Button

13 Side Button 1

[1]

14 Side Button 2

[1]

15 Top Display

16 Microphone

17 Main Speaker

18 Bluetooth Pairing Location Indicator

19 Battery

1

These radio controls/buttons are programmable.

Programmable Features

Any reference in this manual to a control that is preprogrammed means that the control must be programmed by a dealer or qualified radio technician using the radio programming software, in order to assign a feature to that control.

The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:

Press

Pressing and releasing rapidly.

Long Press

Pressing and holding for the preprogrammed duration (between

0.25 seconds and 3.75 seconds).

Hold down

Keeping the button pressed.

Assignable Radio Functions

Bluetooth On/Off

Allows you to turn on/off the

Bluetooth.

Bluetooth Audio

Reroute

Allows you to toggle the audio route between radio speaker or

English

25

26

English

Bluetooth

Headset PTT

Bluetooth Clear

All Pairing

Bluetooth Inquiry

On/Off

Bluetooth

Discoverable

On/Off

Call Response

Dynamic Priority

(Conventional

Only)

Emergency

Remote Speaker Microphone and Bluetooth headset.

Keys up the Bluetooth Headset microphone.

Allows you to clear all pairing information for Bluetooth. This is accessed by a long press of the Bluetooth On/Off Button.

Enables Bluetooth Search feature.

Enables Bluetooth visibility.

This is accessed by a long press of the Bluetooth Inquiry

On/Off Button.

Allows you to answer a private call.

Allows any channel in a Scan

List (except for the Priority-One channel) to temporarily replace the Priority-Two channel.

Depending on the programming, initiates or

Internet Protocol

Address

cancels an emergency alarm or call.

Display the Internet Protocol

(IP) address, device name and status of the radio.

Man Down Clear

Clears the alarm of Man Down mode which was triggered when your radio achieves or passes a tilt angle threshold or a combination of the angle threshold and a motion sensitivity level.

Monitor

(Conventional

Only)

Monitors a selected channel for all radio traffic until function is disabled.

Nuisance Delete

Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel from the scan list.

One Touch 1– 4

Launches a specific feature with one single button-press.

You can setup as many as four

Private Line

Defeat

(Conventional

Only)

separately programmed buttons for four different features.

Overrides any coded squelch

(DPL or PL) that is preprogrammed to a channel.

Rekey Request

Notifies the dispatcher you want a new encryption key.

Repeater Access

Button (RAB)

(Conventional

Only)

Allows user to manually send a repeater access codeword.

Reprogram

Request

(Trunking Only)

Request-To-Talk

(Conventional

Only)

Scan

Scan List

Programming

Notifies the dispatcher you want a new dynamic regrouping assignment.

Notifies the dispatcher you want to send a voice call.

Toggles scan on or off.

Selects the scan list for editing

(by long press on the Scan button).

Secure

Transmission

Select

(Conventional and Trunking)

Toggles the Secure

Transmission On or Off when the Secure/Clear Strapping fields is set to

Select

for the current channel and when the radio is model/option capable.

Site Display/

Search (Trunking

Only)

Displays the current site ID and

RSSI value; performs site search for Automatic Multiple

Site Select (AMSS) or

SmartZone operation.

Locks onto a specific site.

Site Lock/Unlock

(Trunking Only)

Talkaround/Direct

(Conventional

Only)

Toggles between using a repeater and communicating directly with another radio.

Basic Zone Bank

Provides access from up to 6 zones by toggling between 2 banks of 3 zones, one group of

3 (A, B and C) to a second group of 3 zones (D, E and F).

Enhanced Zone

Bank

Provides access from up to 75 zones by toggling between 25

27

English

banks (A, B ... X or Y) of 3 zones.

Assignable Settings or Utility Functions

Controls Lock

Light/Flip

TX Power Level

Locks or unlocks the programmable buttons, switches or rotary knobs.

Press the button to toggle the display backlight on or off; press and hold the button to reverse the content of the top display.

Toggles transmit power level between high and low.

Voice

Announcement

Audibly indicates the current feature mode, Zone or

Channel the user has just assigned.

Voice Mute

Toggles voice mute on or off.

Volume Set Tone

Sets the volume set tone.

Accessing the Preprogrammed Functions

You can access various radio functions through the following method.

A short or long press of the relevant programmable buttons.

Push-To-Talk (PTT) Button

A

The

PTT

button on the side of the radio serves two basic purposes:

28

English

• While a call is in progress, the

PTT

button allows the radio to transmit to other radios in the call.

Press and hold down

PTT

button to talk. Release the

PTT

button to listen. The microphone is activated when the

PTT

button is pressed.

• While a call is not in progress, the

PTT

button is used to make a new call. See

Making a Radio Call

on page 41 for more information.

English

29

Identifying Status Indicators

Status Icons

Selected icons are also shown on the first row of the

112 x 32 pixel top monochrome display screen of your radio. The following icons are for the front display screen unless indicated otherwise.

Receiving

Radio is receiving a call or data.

Transmitting

Radio is transmitting a call or data.

Battery

For IMPRES battery operation only – the icon shown indicates the charge remaining in the battery.

For all battery operation – the icon blinks when the battery is low.

30

English

Received Signal Strength Indicator

(RSSI)

The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal.

Roaming

The radio has roamed to and is currently registered to a foreign system.

Direct

On

– Radio is currently configured for direct radio-to-radio communication

(during conventional operation only).

Off

– Radio is connected with other radios through a repeater.

Monitor (Carrier Squelch)

Selected channel is being monitored

(during conventional operation only).

or

Power Level

L

– Radio is set at Low power.

H

– Radio is set at High power.

Scan

Radio is scanning a scan list.

Priority Channel Scan

Blinking dot

– Radio detects activity on channel designated as Priority-One.

Steady dot

– Radio detects activity on channel designated as Priority-Two.

View/Program Mode

Radio is in the view or program mode.

On steady

– View mode

Blinking

– Program mode

Vote Scan Enabled

The vote scan feature is enabled.

or

or or

or

,

, until or

Basic Zone Bank 1

A

– Radio is in Zone 1.

B

– Radio is in Zone 2.

C

– Radio is in Zone 3.

Basic Zone Bank 2

D

– Radio is in Zone 4.

E

– Radio is in Zone 5.

F

– Radio is in Zone 6.

Enhanced Zone Bank

A

– Contains Zone 1, Zone 2 and Zone

3,

B

– Contains Zone 4, Zone 5 and Zone

6,

C

– Contains Zone 7, Zone 8 and Zone

9, until

X

– Contains Zone 70, Zone 71 and

Zone 72,

English

31

32

English

Y

– Contains Zone 73, Zone 74 and

Zone 75.

Secure Operation

On

Off

Secure operation.

Clear operation.

Blinking

Receiving an encrypted voice call.

GPS Signal

On

– Feature is enabled and signal is available.

Off

– Feature is disabled.

Blinking

– Feature is enabled, but no signal is available.

Bluetooth On

Bluetooth is on and ready for Bluetooth connection.

Bluetooth Connected

Bluetooth is currently connected to the external Bluetooth device.

LED Indicator

The LED indicator shows the operational status of your radio.

A

Solid red

Blinking red

Double blinking red

Radio is transmitting.

Radio is transmitting at low battery condition.

Radio is in Emergency Mode.

Rapidly blinking red

Solid yellow

(Conventional

Only)

Blinking yellow

Radio has failed the self test upon powering up or encountered a fatal error.

Channel is busy.

Rapidly blinking green

Radio is on a Priority-One channel while in the Scan List

Programming mode.

Solid green

Blinking green

Radio is receiving a secured transmission.

Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode.

Radio is receiving an individual or telephone call, or is on a

Priority-Two channel while in the Scan List Programming mode.

Note:

No LED indication when the radio receives a clear (non-secured) transmission in trunking Mode.

LED indication can be preprogramed by qualified technician to be permanently disabled. Consult your dealer for further details if you want to disable it.

Intelligent Lighting Indicators

This feature temporarily changes the backlight of the top display screen, and adds a color bar to the main display screen to help signal that a radio event has occurred.

Note:

This feature must be preprogrammed by a qualified radio technician.

English

33

34

English

Backlight and Bar

Color

Orange

Notification

Emergency Alerts

Red

Green

Critical Alerts

Call Alerts

When

The radio initiates an emergency alarm or call.

The radio receives an emergency alarm or call.

The radio battery is low.

The radio is out of range.

The radio enters Failsoft mode.

The radio is unable to establish a full connection with the system.

The radio is unable to authenticate or register with the system.

The radio lost GPS signal or GPS function fails.

The radio receives a private call.

The radio receives a phone call.

The radio receives a call alert.

The radio receives a selective call.

The radio enters Geofence.

Alert Tones

Your radio uses alert tones to inform you of your radio’s condition. The following table lists these tones and when they occur.

You Hear

Short, Low-

Pitched Tone

Long, Low-

Pitched Tone

Tone Name

Radio Self Test Fail

Reject

Time-Out Timer Warning

No ACK Received

Heard

When radio fails its power-up self test.

When an unauthorized request is made.

Four seconds before time out.

When radio fails to receive an acknowledgment.

Individual Call Warning

Tone

Man Down Entry

When radio is in an individual call for greater than 6 seconds without any activity.

When radio initiates Man Down mode.

Time-Out Timer Timed Out

After time out.

Talk Prohibit/PTT Inhibit

(When

PTT

button is pressed) transmissions are not allowed.

Lack of Voice PTT Time out

When the radio ends your call after it detected there are lack of voice for 5 seconds after the PTT is pressed and hold. Your radio ends the call to enable your radio to receive calls from other radio users.

Out of Range

(When

PTT

button is pressed) the radio is out of range of the system.

English

35

36

English

You Hear

A Group of

Low-Pitched

Tones

Short, Medium-

Pitched Tone

Tone Name

Invalid Mode

Busy

Long, Medium-

Pitched Tone

A Group of

Medium-

Pitched Tones

Heard

When radio is on an unpreprogrammed channel.

When system is busy.

Valid Key-Press

Radio Self Test Pass

Clear Voice

At beginning of a non-coded communication.

Priority Channel Received

When activity on a priority channel is received.

Emergency Alarm /Call

Entry

Central Echo

Volume Set

Emergency Exit

When a correct key is pressed.

When radio passes its power-up self test.

When entering the emergency state.

When central controller has received a request from a radio.

When volume is changed on a quiet channel.

Failsoft

Automatic Call Back

Keyfail

When exiting the emergency state.

When the trunking system fails.

When voice channel is available from previous request.

When encryption key has been lost.

You Hear Tone Name

Console Acknowledge

Short, High-

Pitched Tone

(Chirp)

Two High-

Pitched Tones

Ringing

Gurgle

Received Individual Call

Site Trunking

Low-Battery Chirp

GPS Fails

Phone Call Received

Dynamic Regrouping

Talk Permit

Unique, Low-

Pitched Chirp

Unique, High-

Pitched Chirp

Incremental-

Pitched Tone

New Message

Priority Status

Bluetooth Paired

Heard

When status, emergency alarm, or reprogram request ACK is received.

When Call Alert or Private Call is received.

When a SmartZone trunking system fails.

When battery is below preset threshold value.

When the GPS signal is lost or when GPS fails.

When a land-to-mobile phone call is received.

(When

PTT

button is pressed) a dynamic ID has been received.

(When

PTT

button is pressed) is verifying with the system for accepting its transmissions.

When a new message is received.

When a priority message is received.

When Bluetooth accessory is paired with the radio.

English

37

38

English

You Hear

Decremental-

Pitched Tone

A Group of

Very High-

Pitched Tones

Unique Low-

High Tone

Unique High-

Low Tone

Tone Name

Bluetooth Connected

Bluetooth Unpaired

Bluetooth Disconnected

Man Down Continuous

Tone

Heard

When Bluetooth accessory is connected to the radio.

When Bluetooth accessory is unpaired from the radio.

When Bluetooth accessory is disconnected from the radio.

When radio is in Man Down mode and prepares to transmit

Emergency Alarm when the timer of this alarm ends.

Critical Man Down

Continuous Tone

Enhanced Zone Bank Up

When radio is in Man Down Enhanced mode and prepares to transmit Emergency Alarm when the timer of this alarm ends.

When

EZB Up

button is pressed to scroll the Enhance Zone

Bank up.

Enhanced Zone Bank Down

When

EZB Down

button is pressed to scroll the Enhance Zone

Bank down.

General Radio Operation

Selecting a Zone

Your radio must be preprogrammed to allow you to use this feature.

A zone is a group of channels.

Select a zone via the preprogrammed

Zone (3-

Position A/B/C)

switch: a) Move the preprogrammed

Zone (3-Position

A/B/C)

switch to the position of the required zone.

If the zone number entered is unprogrammed, the display shows

INVALID

. Repeat this step.

b) Press the

PTT

button to transmit on the displayed zone channel.

Selecting a Radio Channel

A channel is a group of radio characteristics, such as transmit/ receive frequency pairs.

Select a channel via the preprogrammed

16–

Position Select Knob

to the desired channel.

a) Rotate the preprogrammed

16–Position

Select Knob

to the desired channel.

b) Press the

PTT

button to transmit on the displayed zone channel.

Receiving and Responding to a Radio Call

Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls.

The LED lights up solid red while the radio is transmitting. In conventional mode, the LED lights up solid yellow when the radio is receiving a transmission. In trunking mode, there is no LED indication when the radio receives a transmission.

If the radio is receiving a secure transmission, the

LED blinks yellow.

Receiving and Responding to a Talkgroup Call

To receive a call from a group of users, your radio must be configured as part of that talkgroup.

When you receive a talkgroup call (while on the

Home screen) the radio triggers for your attention with one of the following scenarios depending on the system your radio is configured:

39

English

• For ASTRO Conventional system, the LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID.

• For Trunking system, the display shows the caller alias or ID.

1

Hold the radio vertically 1 to 2 inches (2.5 to 5.0

cm) from your mouth.

2

Press the

PTT

button to respond to the call.

The LED lights up solid red.

3

Release the

PTT

button to listen.

40

See also

Making a Talkgroup Call

on page 41 for

details on making a Talkgroup Call.

Receiving and Responding to a Private Call (Trunking

Only)

A Private Call is a call from an individual radio to another individual radio.

The one-to-one call between the two radios are not heard by the others in the current talkgroup. The transmitting radio automatically verifies that the receiving radio is active on the system and can display the caller ID.

English

Note:

With the inactivity timer enabled (optional), when there is no response from the receiving radio, the transmitting radio exits the call with Menu Inactive

Exit tone after the timer expires.

When you receive a Private Call, you hear two alert tones and the LED blinks green. The display shows

CALL RCV

, alternating with the caller alias (name) or

ID (number).

1

Press the

Call Response

button within 20 seconds after the call indicators begin.

2

Press and hold the

PTT

button to talk. Release the

PTT

button to listen.

3

Press the

Call Response

button to hang up and return to the Home screen.

You cannot initiate a Private Call.

Receiving and Responding to a Telephone Call

(Trunking Only)

This feature allows you to receive calls similar to standard phone calls from a landline phone.

Note:

With the inactivity timer enabled (optional), if there is no response to the call after the timer expires, your radio exits the call with Menu Inactive Exit tone.

When you receive a Telephone Call, you hear telephone-type ringing and the LED blinks green. The display shows

PHN CALL

and the call received icon blinks.

1

Press the

Call Response

button within 20 seconds after the call indicators begin.

2

Press and hold the

PTT

button to talk. Release the

PTT

button to listen.

3

Press the

Call Response

button to hang up and return to the Home screen.

You cannot initiate a Telephone Call.

Making a Radio Call

You can select a zone, channel, subscriber ID, or talkgroup by using:

• The preprogrammed

Zone

switch.

• The

16-Position Select Channel Knob

.

Making a Talkgroup Call

To make a call to a group of users, your radio must be configured as part of that talkgroup.

1

Turn the

16-Position Select Channel Knob

to select the channel with the desired talkgroup.

2

Hold the radio vertically 1 to 2 inches (2.5 to 5.0

cm) from your mouth.

3

Press the

PTT

button to make the call.

The radio shows different indicators based on the system the radio is configured.

• For ASTRO Conventional system, the LED lights up solid red. The display shows the talkgroup alias or ID.

• For Trunking system, the LED lights up solid red.

4

Speak clearly into the microphone.

5

Release the

PTT

button to listen.

English

41

Switching Between Repeater or Direct

Operation Button

The

Repeater Operation

increases the radio’s range by connecting with other radios through a repeater.

The transmit and receive frequencies are different.

The

Direct

or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same.

Press the preprogrammed

Repeater/Direct

switch to toggle between talkaround and repeater modes.

The display shows

RPTR MOD

if the radio is currently in Repeater mode.

The display shows

DIR MODE

and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only).

42

Monitor Feature

Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case.

This digital technology quiets the transmission by removing the noise from the signal and allows only the clear voice or data information to be heard.

Use the Monitor feature to make sure a channel is clear before transmitting.

Monitoring a Channel

Monitoring a Channel via the

Monitor

and

Volume Set

button.

a) Press the preprogrammed

Monitor

button.

The Carrier Squelch indicator appears on the display when you monitor a channel via the preprogrammed Monitor button.

b) Press and hold the

Volume Set

button to hear the volume set tone.

c) Adjust the

Volume Control Knob

if necessary.

d) Release the

Volume Set

button.

e) Press and hold the

PTT

button to transmit.

The LED lights up solid red.

f) Release the

PTT

button to receive (listen).

Monitoring Conventional Mode

Your radio may be preprogrammed to receive Private-

Line

®

(PL) calls.

English

1

Momentarily press the

Monitor

button to listen for activity.

The Carrier Squelch indicator appears on the display.

2

Press and hold the

Monitor

button to set continuous monitor operation.

The duration of the button press is programmable.

3

Press the

Monitor

button again, or the

PTT

button, to return to the original squelch setting.

If you try to transmit on a receive-only channel, you hear an invalid tone until you release the

PTT

button.

English

43

44

Advanced Features

Advanced Call Features

Selective Call (ASTRO Conventional Only)

This feature allows you to receive a call from a specific individual with privacy and without the annoyance of having to listen to conversations that are of no interest to you.

Receiving a Selective Call

When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The backlight of the screen turns green momentarily and the display briefly shows

CALL RCV

.

The speaker unmutes.

1

Hold the radio vertically 1 to 2 inches (2.5 to 5.0

cm) from your mouth.

2

Press and hold the

PTT

button to talk. Release the

PTT

button to listen.

You cannot initiate a Selective Call.

Responding to the Dynamic Regrouping Feature

(Trunking Only)

This feature allows the dispatcher to temporarily reassign selected radios to a particular channel where they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician.

You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher.

Note:

If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, you hear an invalid tone.

When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. You hear a Gurgle tone and the display shows the dynamically regrouped channel’s name.

Press the

PTT

button to talk. Release

PTT

button to listen.

When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel

English

that you were using before the radio was dynamically regrouped.

Requesting a Reprogram (Trunking Only)

This feature allows you to notify the dispatcher when you want a new dynamic regrouping assignment.

Press the preprogrammed

Reprogram Request

button to send reprogram request to the dispatcher.

The display shows

RPGM

and

PLS WAIT

.

If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows

ACK RCVD

and the radio returns to the

Home

screen.

If the dispatcher does not acknowledge the reprogram request within six seconds, you hear a low-pitched alert tone and the display shows

NO ACK

.

Classification of Regrouped Radios

The dispatcher can classify regrouped radios into either of two categories:

Select

Enabled

Select-enabled radios are free to change to any available channel, including the dynamic-regrouping

Select

Disabled

channel, once the user has selected the dynamic-regrouping position.

Select-disabled radios cannot change channels while dynamically regrouped.

The dispatcher has forced the radio to remain on the dynamic-regrouping channel.

The Scan or Private Call feature cannot be selected while your radio is Select Disabled.

Scan Lists

Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/ group.

Your radio supports different types of Scan Lists:

• Trunking Priority Monitor Scan List

• Conventional Scan List

• Talkgroup Scan List

Please refer to a qualified radio technician for the maximum number of Scan Lists can be programmed

45

English

in your radio. These lists must be preprogrammed by a qualified radio technician.

Viewing a Scan List

Turn the

16-Position Select Knob

to view the members on the list.

46

Viewing and Changing the Priority Status

Press the

Top Side (Select)

button to change the priority status of the currently displayed channel or the scan list status icon of the currently displayed channel.

The radio shows one of following priority status icons and scenarios:

• A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The

LED lights up solid green.

• A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green.

• A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-

One channel, regardless of traffic on nonpriority channels.

• No icon indicates that the current channel is deleted from the scan list.

Scan

This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels.

Turning Scan On or Off

Press the preprogrammed

Scan

button to toggle

SCAN ON

or

SCAN OFF

to initiate or stop scan.

If the scan is enabled, the display shows

SCAN ON and the scan status icon.

If the scan is disabled, the display shows

SCAN

OFF

.

Making a Dynamic Priority Change (Conventional Scan

Only)

While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel.

English

This change remains in effect until scan is turned off.

Scan then reverts to the preprogrammed (original) setting.

Making a Dynamic Priority Change via the preprogrammed

Dynamic Priority

button: a) When the radio locks onto the channel designated as the new Priority-Two channel, press the preprogrammed

Dynamic Priority

button.

The radio continues scanning the remaining channels in the list.

Deleting a Nuisance Channel

If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.

This capability does not apply to priority channels or the designated transmit channel.

Note:

Deleting a nuisance channel is only possible through the preprogrammed

Nuisance Channel

Delete

button.

When the radio is locked onto the channel to be deleted, press the preprogrammed

Nuisance

Delete

button.

The radio continues scanning the remaining channels in the list.

Restoring a Nuisance Channel

To restore the deleted nuisance channel, perform one of the following actions:

• Turn scan off, and then on.

• Change channels.

• Turn off the radio, and then turn it back on.

Nuisance mode delete can be disabled by the system administrator.

Call Alert Paging

This feature allows your radio to work like a pager.

The radio which you missed its call can send a Call

Alert page to your radio. The sender also able to know that your radio is active.

Note:

This feature must be preprogrammed by a qualified radio technician.

47

English

Receiving a Call Alert Page

When you receive a Call Alert page, you hear four repeating alert tones and the LED blinks green. The call received icons blinks and the display shows

PAGE

RCV

.

Press any button to clear the Call Alert page.

You cannot send a Call Alert page.

48

Emergency Operation

The Emergency feature is used to indicate a critical situation.

If the

Top (Orange)

button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel.

Your radio supports the following Emergency modes:

• Emergency Alarm

• Emergency Call (Trunking Only)

• Emergency Alarm with Emergency Call

• Silent Emergency Alarm

Check with your dealer or system administrator for more information on the programming of this feature.

English

Only

one

of the Emergency modes above can be assigned to the preprogrammed

Emergency

button.

Note:

To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second.

The radio operates in the normal dispatch manner while in Emergency Call, except if enabled, it returns to one of the following:

Tactical/Non-

Revert

Non-Tactical/

Revert for

Conventional system

Non-Tactical/

Revert for

Trunking system

The radio sends emergency alarm and/or make emergency call on the current selected channel.

The radio reverts to the preprogrammed emergency channel to send alarm and/or make emergency call.

The radio reverts to the preprogrammed emergency talkgroup to send alarm and/or make emergency call.

Man Down is an alternate way to activate the

Emergency feature on the condition the Emergency must be set up for this feature to operate.

See

Man Down

on page 54 for details.

Sending an Emergency Alarm

This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher.

Note:

Emergency button press timer by default is set to 1 second. This timer is programmable from 0 – 6 seconds by a qualified technician.

Press the preprogrammed

Emergency

button.

One of the following scenarios occurs:

• The display shows

EMERGENCY

and the current zone or channel. You hear a short mediumpitched tone and the LED blinks red momentarily.

• You hear the radio sounds a short low-pitched tone to indicate that the selected channel does not support emergency and rejects to launch emergency mode.

When you receive the dispatcher’s acknowledgment, the display shows

ACK RCVD

. You hear four tones, the alarm ends, and the radio exits the Emergency Alarm mode.

If no acknowledgement is received, the display shows

NO ACK

. The alarm ends and the radio exits the

Emergency Alarm mode.

Sending an Emergency Call (Trunking Only)

This feature gives your radio priority access to a talkgroup.

1

Press the preprogrammed

Emergency

button.

One of the following scenarios will occur:

• The display shows

EMERGNCY

and the current zone or channel. You hear a short mediumpitched tone and the LED blinks red momentarily.

• You hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode.

2

Hold the radio vertically 1 to 2 inches (2.5 to 5.0

cm) from your mouth.

3

Press and hold the

PTT

button. Speak clearly into the microphone.

49

English

4

Release the

PTT

button to end the transmission and wait for a response from the dispatcher.

5

To exit Emergency Call, press and hold the preprogrammed

Emergency

button for about a second.

50

Sending an Emergency Alarm with Emergency Call

This feature gives your radio priority access on a channel for conventional system, and to a talkgroup for trunking system.

1

Press the preprogrammed

Emergency

button.

If successful, the display shows

EMERGNCY

on the current zone and channel. You hear a short, medium-pitched tone and the LED blinks red momentarily.

The radio exits Emergency Alarm and enters the

Emergency Call state when one of the following scenarios occur:

• You receive the dispatcher’s acknowledgment.

The display shows

ACK RCVD

.

• You receive no acknowledgement. The display shows

NO ACK

.

• You press the

PTT

button while in the

Emergency Alarm mode.

If unsuccessful, you hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode.

2

Hold the radio vertically 1 to 2 inches (2.5 to 5.0

cm) from your mouth.

3

Press and hold the

PTT

button. Speak clearly into the microphone.

4

Release the

PTT

button to end the transmission and wait for a response from the dispatcher.

5

To exit Emergency Call, press and hold the preprogrammed

Emergency

button for about a second.

Turning the radio off also cancels the emergency state.

Sending a Silent Emergency Alarm

This feature allows you to send an Emergency Alarm to the system without triggering any audio or visual indicators.

English

1

Press the preprogrammed

Emergency

button.

The display shows no changes, the LED does not light up, and you hear no tones. The silent emergency state continues until you perform the next step.

2

Perform one of the following actions:

• You press and hold the preprogrammed

Emergency

button for about a second to exit the Silent Emergency Alarm mode.

• Press and release the

PTT

button to exit the

Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode.

Change of Channels during Emergency

For ALL Emergency transmissions, when changing channels:

• If the new channel is also preprogrammed for

Emergency, you can change channels while in

Emergency operation. The emergency alarm or call continues on the new channel.

• If the new channel is

NOT

preprogrammed for

Emergency, the display shows

NO EMERG

, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for

Emergency.

Emergency Keep-Alive Feature

This feature, when enabled, prevents the radio from being turned off via the

On/Off Control Knob

when the radio is in the Emergency state.

Note:

The radio only exits the Emergency state using one of the ways mentioned in the previous sections.

See

Sending an Emergency Alarm

on page 49,

Sending an Emergency Call (Trunking Only)

on page

49,

Sending an Emergency Alarm with Emergency

Call

on page 50, or

Sending a Silent Emergency

Alarm

on page 50.

Fireground (Conventional Only)

The portable Fireground Communications System is designed for deployment at an incident scene. It consists of five central components:

• Your APX portable radios

• Incident Management Software

• Command Terminal

• Radio Frequency (RF) Modem

• DVRS (Optional)

51

English

52

English

These components provide on-scene and inbuilding radio coverage, and enhanced personnel accountability and monitoring.

The radio helps to indicate your presence on the scene if it is in the range of the Incident Commander command terminal.

Each Fireground Communication System radio automatically reports your radio ID on the commander mobile command terminal. Your name, riding position and sector are all can be configured to be seen at the

Commander’s command terminal.

If you have a critical situation, you can press the

Emergency button which activates an alarm on the

Incident Management Software at the command terminal.

The Fireground signals transmission is always exchanging data between your radio and the RF

Modem and command terminal. The status of your radio includes:

• Powering up or down the radio

• Automatic response to Polling

• Response to Evacuation commands

• Pressing the

PTT

button to make voice transmission

• Sending an Emergency Alarm and Call

Entering Fireground Zone Channel

1

Upon powering up, perform one of the following actions:

• If the Fireground Zone Channel is set as default, you hear gurgle tone and the home screen. You are in Fireground zone channel.

• If the Fireground Zone Channel is set as default, but you hear a short, low-pitched tone, the display shows

REG FAIL

to indicate that the command terminal does not respond to

Fireground Zone Channel. Get a qualified technician for assistance.

• If your home channel is not Fireground Zone

Channel, toggle or change the radio zone channel to Fireground Zone Channel.

2

Listen for a transmission. Adjust the

Volume

Control Knob

if necessary.

3

Perform one of the following actions:

• Press and hold the preprogrammed

Volume

Set

button to hear the volume set tone. Adjust

the

Volume Control Knob

if necessary.

Release the

Volume Set

button.

• At the desired Fireground zone and channel, press the preprogrammed

Monitor

button and listen for activity. Adjust the

Volume Control

Knob

if necessary.

• If your radio is working in Fireground Zone

Channel, proceed to next step.

4

Press and hold the

PTT

button to transmit. The

LED lights up solid

red

while transmitting. Talk into the microphone clearly if needed.

5

Release the

PTT

button to receive.

You hear a Transmit End Tone.

Responding to Evacuation Indicator

When Incident Commander triggers Evacuation signal from his command terminal, the RF Modem updates everyone in the Fireground Communication

System with the order to evacuate the incident site.

Your radio sounds the Evacuation Tone at the profile maximum alert tone volume level. The display shows

EVACUATE

.

Perform one of the following actions:

• Move the

Volume Control Knob

to adjust the volume of the Evacuation Tone from full volume.

• Perform any action on the radio other than volume adjustments to cancel the evacuation indications and update the command terminal.

• If preprogrammed with Manual

Acknowledgement of Evacuation Command, pressing the

PTT

button shall cancel the indications and acknowledge the command terminal.

Tactical Public Safety(TPS) (Conventional

Only)

TPS enabled the user of a group to identify a transmission starts and ends clearly by displaying the caller name or ID on the radio display.

Using TPS Normal Transmission

At TPS Zone Channel, perform one of the following actions:

• Press

PTT

button to transmit. Talk clearly into the microphone. Release

PTT

button to listen.

53

English

54

• Receive and listen to call, the radio displays the caller’s name or ID.

Using TPS Emergency Transmission

The following are two important alert tones designed for this feature.

Emergency

Beacon

Emergency

Call De-Key

Sidetone

During Emergency if the TPS radio user pushes the

Emergency

button, the radio sounds a Beacon at the maximum volume of the radio at radio’s internal speaker and it is not adjustable. This beacon goes to silent when user presses the

PTT

button for voice transmission.

The radio sounds an alert tone to remind radio user that the

Emergency Mode is still active after user releases the

PTT

button for an

Emergency call transmission. The volume of loudness depends on the maximum tone at your radio profile.

1

Press the

Emergency

button to enter Emergency

Mode.

You hear Emergency Beacon.

English

2

Press

PTT

button to make Emergency Call.

3

Release to listen.

You hear Emergency Call De-Key Sidetone. After a short pause, you hear Emergency Beacon.

4

Long press

Emergency

button to exit Emergency mode and cancel Emergency Beacon.

Man Down

Man Down condition is determined based upon the radio tilt angle or a combination of radio tilt angle and the lack of radio motion.

Man Down feature is an alternate way to activate the

Emergency feature if Emergency has been programmed in your radio.

Note:

This feature could be preprogrammed for all channels that support Emergency feature or could be preprogrammed specifically to a zone and channel which has Emergency feature. Consult your agent or qualified technician for more details.

Your radio automatically activates Emergency Alarm or Call when the radio achieves or passes a tilt angle threshold or a combination of the angle threshold and

radio motion below the motion sensitivity level, depending upon how the radio is programmed. The radio must stay in this condition for a preprogrammed amount of time before the Emergency Alarm or Call is activated.

Note:

It is recommended that an Emergency button is preprogrammed in order to allow the user to exit the emergency condition.

The Man Down feature provides a

Clear

function to the user. After a Man Down condition has been detected, the user can press a preprogrammed

Clear

button or preprogrammed

Menu Select

button to cancel the Man Down condition. The radio remains in the Man Down state without triggering an emergency condition until the radio is moved out of the Man

Down state, at which point Man Down functionality resumes.

The Man Down feature has three phases:

1

The radio senses the Man Down condition and

Pre-Alert Timer is initiated.

2

Man Down condition continues for the time duration defined in the Pre-Alert Timer field. At the end of this time, the radio alerts the user on the

Man Down status with an audible alert tone and

MAN-DOWN

text on the screen. The Post-Alert Timer also initiates at this point.

3

Man Down condition continues for the time duration defined in the Post-Alert Timer field. Once the timer expires, the Emergency alarm is transmitted. The Man Down Clear function is used in this phase to cancel the Man Down condition.

The following scenarios affect the timers:

• Pressing the

PTT

button suspends the Man Down timers; releasing the

PTT

button re-initiates the

Pre-Alert Timer.

• Pressing other buttons on the radio does not impact these timers.

• Repositioning the radio exits the Man Down feature, which stops and resets the timers.

• Pressing a preprogrammed

Clear

button or pressing a

Menu Select

button preprogrammed for

Clear

stops and resets the timers. The timers do not restart until the radio is repositioned.

Note:

Emergency must be set up for this feature to operate. For details on operating the Emergency

alerts, please see

Emergency Operation

on page 48.

English

55

56

If the radio is preprogrammed to horizontal only, it must be worn in a vertical position otherwise the Man

Down alert may be inadvertently triggered.

When the radio is programmed with Man Down feature, special care is required when charging the radio with a wall mounted charger. See

Proper Ways to Handle the Radio

on page 83 for details.

Pre-Alert Timer

This timer sets the amount of time that a Man Down condition must be present before the radio-user is warned of the Man Down condition.

When the radio detects that it has returned to the vertical position or when the radio detects motion, the

Pre-Alert timer stops and is reset.

The Pre-Alert timer reinitiates when the radio detects it is in the horizontal position or motionless again.

Post-Alert Timer

This timer sets the amount of time the radio needs to remain in the Man Down condition before the

Emergency alarm is transmitted. When the Post-Alert

Timer is initiated, the radio alerts the user with an audible tone and displays the “

MAN-DOWN

” text.

See

Exiting Man Down Feature

on page 57 to exit

Man Down feature.

Radio Alerts When Man Down Feature is Triggered

The Man Down alert tone volume is directly related to the radio’s volume. Ensure that the radio’s volume is loud enough so that the user does not miss the Post-

Alert tone.

Note:

If the radio is programmed with Silent

Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature.

If the radio is programmed in Surveillance Mode, the radio inhibits all tones and lights on the radio including the Man Down tones.

Triggering Emergency

When the user does not clear the Man Down condition and the Post-Alert Timer comes to an end,

Emergency Alarm or call is triggered. The radio sends emergency message to units within the same

Talkgroup. The radio also sends ID number and GPS coordinates to dispatcher if these features are enabled. User can exit Emergency following the

Emergency procedure. See

Emergency Operation

on page 48 for details.

English

Note:

At this point the Man Down features is complete. Use normal Emergency procedures to cancel Emergency transmissions.

Radio Alerts When Man Down Enhanced is Triggered

Note:

This feature is to be preprogrammed specifically to a zone and channel which supports

Emergency feature.

The volume and repetition duration of Man Down

Enhanced alert tone could be customized and preprogrammed to suite the required situation.

Consult your agent or qualified technician for more details.

When the radio initiates Man Down Enhanced, you hear the Critical Man Down Continuous alert tone from the radio speaker. The volume of this tone is set to the louder of the preprogrammed minimum level or the current radio speaker level. This acts as a beacon to find the radio.

Note:

If the radio is programmed with Silent

Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature.

If the radio is programmed in Surveillance Mode, the alert tone can be heard from the radio speaker.

Once the alert tone is active, changing to another channel with different setup triggers a different response from the radio as described next.

• The alert tone is inhibited when you change to a channel without Emergency feature.

• The alert tone is inhibited when you change to a channel with Emergency but no Man Down feature.

• The current alert tone is inhibited and is replaced with a different alert tone when you change to a channel with Emergency and different Man Down configuration.

• The alert tone continues when you change to a channel with Emergency and similar Man Down configuration.

Exiting Man Down Feature

If you are not in a real Man Down situation, you should exit the Man Down feature and prevent emergency from going off with the following operation.

Perform one of the following actions:

• Repositioning the radio or shaking the radio

(when motion sensitivity is enabled).

57

English

58

• Press the preprogrammed

Man Down Clear

button to exit.

Re-Initiating Man Down

After exiting the Emergency Operation when the radio is still in Man Down condition (tilted achieving threshold angle or motionless), user must first exit

Man Down condition to then reinitiate the Man Down feature.

Return the radio to the vertical position or shake the radio (when motion sensitivity is enabled).

Testing the Man Down Feature

Enable the Emergency feature with Silent Alarm disabled, but not in Surveillance Mode before running this test on the radio.

1

Turn the radio on and place in the vertical position, for at least 5 seconds.

2

Lay the radio down in the horizontal position.

3

Wait for alert tone.

One of the following scenarios will occur:

• The radio alerts with audible tone and displays

MAN-DOWN

.

• If no tone is heard, make sure that the Man Down feature is enabled on your radio. If Man Down feature was not enabled, please enable it and

repeat

1

to

3

.

• If the Man Down feature is enabled and no tone is heard, send the radio to a qualified technician.

Secure Operations

Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels.

Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message.

Selecting Secure Transmissions

Turn the preprogrammed

Secure/Clear

switch to the secure position.

Note:

If the selected channel is preprogrammed for clear-only operation, when you press the

PTT

English

button, you hear an invalid mode tone and the display shows

CLR TX

.

The radio will not transmit until you set the

Secure/Clear

switch to the clear position.

Selecting Clear Transmissions

Turn the preprogrammed

Secure/Clear

switch to the clear position.

Note:

If the selected channel is preprogrammed for secure-only operation, when you press the

PTT

button, you hear an invalid mode tone and the display shows

SEC TX

.

The radio will not transmit until you set the

Secure/ Clear

switch to the secure position.

The radio can be configured to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details.

Managing Encryption

Loading an Encryption Key

Note:

Refer to the key-variable loader (KVL) manual for equipment connections and setup.

1

Attach the KVL to your radio.

The display shows

KEYLOAD

, and all other radio functions, except for power down, backlight, and volume, are locked out.

2

Select the required keys and press the

Menu

Select

button directly below

LOAD

on the KVL.

This loads the encryption keys into your radio.

When the key has been loaded successfully, one of the following scenarios occurs:

• You hear a short tone for single-key radios.

• You hear an alternating tone for multikey radios.

Multikey Feature

This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm.

There are two types:

Conventional

Multikey

The encryption keys can be tied

(strapped), on a one-per-channel basis, through Customer

Programming Software. In addition, you can have operator-selectable

59

English

60

English

Trunked

Multikey

keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups.

If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcementgroup basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure.

Erasing the Selected Encryption Keys

This feature allows you to erase all or selected encryption keys.

Erasing the single key in radios with the single-key option and erasing all keys in radios with the multikey option via the preprogrammed

Top Side

(Select)

button and

Top (Orange)

button: a) Press and hold the

Top Side (Select)

button.

b) While holding

Top Side (Select)

button down, press the

Top (Orange)

button.

The display shows

PLS WAIT

. When all the encryption keys have been erased, the display shows

ALL ERASED

.

Note:

Do

not

press the

Top (Orange)

button before pressing the

Top Side (Select)

button, unless you are in an emergency situation as this sends an emergency alarm.

Requesting an Over-the-Air Rekey (ASTRO

Conventional Only)

Ensure that the Unique Shadow Key (USK) is loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information.

This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user.

Press and hold the preprogrammed

Rekey

Request

button to send the rekey request.

If the rekey operation fails, a bad-key tone sounds and the display shows

RKY FAIL

.

Note:

The rekey operation failure indicates that your radio does not contain the Unique Shadow

Key (USK).

MDC Over-the-Air Rekeying (OTAR) Page

This feature allows you to view or define MDC Overthe-Air Rekeying (OTAR) features. It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to

Rekey Requests, OTAR transmissions include

Delayed Acknowledgements, and Powerup

Acknowledgements.

Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly.

Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.

Infinite UKEK Retention

This feature enables Unique Key Encryption Key

(UKEK) to be permanently stored in the radio even when all of the encryption keys is erased. Without this

UKEK key, the radio could not be over the air rekeyed.

Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.

Hear Clear

Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.

There are two components of Hear Clear.

Companding

Reduces the channel noise, e.g.

OTA transmission, that is predominantly present in UHF2 and

900 MHz channel with the following features.

Compressor

Reduces the background noise flow and the speech signal at transmitting radio.

Expander

Expands the speech while the noise flow

61

English

Random FM

Noise

Canceller

(Flutter

Fighter)

remains the same at receiving radio.

Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-

Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal.

The Random FM Noise Canceller operates only in receive mode.

62

Global Positioning System (GPS)

This feature uses information from the Global

Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude or

MGRS format per request from customers. The availability and accuracy of this location information

(and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature.

For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky.

Once GPS is enabled, the radio displays the GPS icon on the screen. The dispatcher can always request the system to determine the real-time location coordinates of the radio.

GPS Operation

The GPS technology uses radio signals from earth orbiting satellites, to establish the location coordinates, maximizing your view of clear unobstructed sky is essential for optimum performance.

Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to:

• Underground locations

• Inside of buildings, trains, or other covered vehicles

• Under any other metal or concrete roof or structure

English

• Between tall buildings or under dense tree-cover

• In temperature extremes outside the operating limits of your radio

Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher.

Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites.

Note:

Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes farther away.

The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of

Defense GPS user policy and the Federal Radio

Navigation Plan. These changes may affect the performance of the GPS feature on your radio.

GPS Performance Enhancement

Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites.

To maximize the ability of your radio to determine a fix, take note of the following guidelines:

• For your initial fix, hold the radio in the face position.

• Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky.

Peer-Location on the Display (ASTRO Conventional only)

This feature is only available for radio-to-radio voice transmissions, dispatch call and selective call in conventional ASTRO system. For radio-to-radio transmission, in order to allow the radio to show peerlocation, the voice should be directly sent from one radio to another radio without passing through any infrastructure facility such as repeaters, phone or

DVRS system. Both the transmitting radio and receiving radio must be configured to enable them to send and/or receive the GPS coordinates. You can

63

English

64

English check with your nearest qualified technician for more details.

Note:

If the receiving radio is operating in a Mixed

Mode channel, only if its voice transmission is via conventional ASTRO system then it can receive the location coordinates of its peers.

This feature is also operable in a Scan Active channel or Scan Talkback channel.

Upon receiving a voice transmission with GPS coordinates enabled on the receiving radio, the display shows the coordinates available in full or in short coordinates. There are two different formats available. Refer to the following list for the details shown in the Peer-Location quick text. Consult your agent to pick the best format to configure to your radio.

Full location coordinates

• PTT ID (This is optional.)

• Longitude and latitude

• Relative distance or direction.

Short location coordinates

• PTT ID (This is optional.)

• Longitude and latitude

Note:

If the transmitting radio is stale at its location after a period of time, the receiving radio display shows

ID:<PTT ID> LKL: <Coordinates> <distance>

. If the radio is not configured to show

PTT ID

, you see

LAST KNWN LOC: <Coordinates> <distance>.

If the transmitting radio does not have GPS or the receiving radio could not decode the GPS signal of the received signal, the receiving radio display shows

ID:<PTT ID> UNK LOC

. The

PTT ID

seen here is optional to be shown on the display per requirement of usage.

Trunking System Controls

Using the Failsoft System

The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel.

During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency. You hear a mediumpitched tone and the display shows

FAILSOFT

.

When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation.

To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure.

1

Rotate the

Mode Knob

to change to a different repeater frequency.

2

Press the

PTT

button to talk, and release the button to listen.

Out-of-Range Radio

When your radio goes out of the range of the system, it can no longer lock onto a control channel.

You hear a low-pitched tone and/or the display shows the currently selected zone/channel combination and

OUT RNG

. Your radio remains in this out-of-range condition until it locks onto a control channel, it locks onto a failsoft channel, or it is turned off.

Site Trunking Feature

If the zone controller loses communication with any site, that site reverts to site trunking.

The display shows the currently selected zone/ channel combination and

STE TRNK

.

Note:

When this occurs, you can communicate only with other radios within your trunking site.

Locking and Unlocking a Site

This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites.

This feature should be used with caution, since it inhibits roaming to another site in a wide-area system.

Use the preprogrammed

Site Lock/Unlock

button to toggle the lock state between locked and unlocked.

The radio saves the new site lock state and returns to the Home screen.

Site Display and Search Button

The

Site Display

and

Site Search

button allows you to view the name of the current site or force your radio to change to a new one.

Viewing the Current Site

Press the preprogrammed

Site Displ/Srch

button.

65

English

66

The display shows momentary the name of the current site and its corresponding received signal strength indicator (RSSI).

Changing the Current Site

Press and hold down the preprogrammed

Site

Displ/Srch

button.

You hear a tone and the display shows momentary

SCANNING

.

When the radio finds a new site, it returns to the

Home screen.

Mission Critical Wireless - Bluetooth

®

-

This feature allows your radio to extend its functionality by connecting to external proprietary

Motorola accessories.

Note:

It is recommended to use Motorola proprietary

Mission Critical Wireless (MCW) devices with APX radios during Mission Critical operations as other

Bluetooth

®

devices may or may not meet the mission critical standard.

Your radio must be preprogrammed to allow you to use this feature.

English

The use of this feature requires the "Full Feature" expansion board together with the Bluetooth

Software.

The default setting for Bluetooth-enabled radio is

Bluetooth ON. See

Turning the Bluetooth Off

on page

67 to turn the Bluetooth OFF.

Currently your radio supports the following Bluetooth devices or profiles.

• Headset (HSP)

• Dial Up Networking (DUN)

• Personal Area Networking (PAN)

• Serial Port (SPP)

Turning the Bluetooth On

Turning the Bluetooth on via the preprogrammed button: a) Press the preprogrammed button to turn on the

Bluetooth.

You hear a short, medium-pitched tone. The display shows momentary

BT ON

, and appears.

If Bluetooth fails to launch, the display shows

BT ON FL

.

Turning the Bluetooth Off

Turning the Bluetooth off via the preprogrammed button: a) Press the preprogrammed button to turn off the

Bluetooth.

You hear a short, medium-pitched tone. The display shows momentary

BT OFF

and disappears.

Re-Pair Timer

There are two options for configuring the Bluetooth pairing type of the radio. The type defines the duration the radio and the accessory retain the pairing information.

Immediate

(For MCW accessories only.) When the radio and/or device is turned off after pairing, the keys are lost. Due to this, when your radio and your device are turned back on, they are unable to reconnect. The user must re-pair the devices to re-establish a new set of

pairing keys. See

Pairing with Low

Frequency-Motorola Proximity Pairing

Infinite

Re-Pair

Timer

Options

Immediate

(For MCW

Accessories only)

(LF-MPP) Feature

on page 69 and

Standard Pairing Feature

on page 70.

(For all Bluetooth devices.) When the radio and/or device are turned off after pairing, keys are

not

lost. When the radio and the device are turned back on, they can resume the Bluetooth connection without user intervention.

Re-Pair Timer Scenarios

• When the radio is powered off, pairing key is lost immediately, and accessory attempts to pair again. If pairing is unsuccessful within the Drop Timer value, the accessory automatically powers off.

• When the accessory is powered off, all keys are lost immediately, and the user must re-pair the devices.

English

67

Re-Pair

Timer

Options

Re-Pair Timer Scenarios

• When the device loses Bluetooth connection, the device will attempt to re-establish Bluetooth

Connection within the Drop

Timer value.

Infinite (For all

Bluetooth devices)

• When the radio is powered off, the accessory attempts to reestablish the Bluetooth

Connection for a period of time depending upon the Drop Timer value. If the device fails to reconnect within the period, the accessory then powers off.

Bluetooth Drop Timer

The Bluetooth Drop Timer has two different settings and functions, depending upon the selection of the

Re-Pair Timer.

68

English

Re-Pair Timer

Options

Immediate

(For MCW

Accessories only)

Description

0 – 15 minutes programmable buffer time to re-establish the

Bluetooth Connection when the

Bluetooth signal is out of range.

If either device powers

off

, the pairing keys are immediately cleared from both devices and the devices must re-pair.

Infinite (For all

Bluetooth devices)

This Timer only applies to the accessory. The programmable timer choices are: 0 – 15 minutes, 2 hours, 4 hours or 8 hours.

Do note there are exceptions for

Operation Critical Wireless (OCW) headset and

PTT

which are preprogrammed to 8 hours.

This is a "stay alive" time that the accessory will remain

on

without the device reconnecting before powering off. The radio will remain

Re-Pair Timer

Options

Description on

until the user powers the radio

off

. The radio and accessory will remain paired indefinitely. Once the device re-connect, the timer is reset.

The radio could not control the Drop Timer of

Personal Area Networking (PAN), Dial-Up Networking

(DUN), Commercial Off- The-Shelf (COTS) and data services. It is depends on the specifications of these external devices.

Check with your dealer or system administrator for more information about these timers.

To establish the Bluetooth Connection, see

Pairing with Low Frequency-Motorola Proximity Pairing (LF-

MPP) Feature

on page 69 or

Standard Pairing

Feature

on page 70 .

Pairing with Low Frequency-Motorola Proximity Pairing

(LF-MPP) Feature

Ensure that Bluetooth feature of your radio is on and the Bluetooth tones are enabled.

Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.

The range of Bluetooth operation is 10 meters line-ofsight communication. This is an unobstructed path between the location of the signal transmitter (your radio) and the location of the receiver (your device or accessory).

Obstacles that can cause an obstruction in the line-ofsight include trees, buildings, mountains, cars and etc.

It is

not

recommended that you leave your radio behind and expect your accessory to work with a high degree of reliability when they are separated.

At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken". To correct this problem, simply position the accessory and radio closer to each other (within the 10 meter defined range) to re-establish clear audio reception.

Note:

Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk Time power consumption, not the Standby Time consumption.

69

English

70

English

Turn on the accessory. Then place it close to your radio aligning the Bluetooth Pairing Location ( ) on the radio to the Bluetooth Pairing Location (a blue dot) on the accessory.

If the pairing process is successful, you hear an incremental-pitched tone. The radio begins to connect to the device.

If the pairing process fails, you hear a short, lowpitched tone. The display shows

PAIRING alternates with

FAILED

. Repeat this step.

The radio tries to establish connection with the device once paired.

Note:

If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows

<Device

Type> UNPAIRED

. Repeat this step to re-initiate the pairing process.

If the connection is successful, you hear an incremental-pitched tone. The display shows

<Device

Type> CONNCTED

and the Bluetooth icon turns from

to .

If the radio has the pairing record of the device and the connection fails, you hear a short, low-pitched tone. The display shows

<Device Type> CON FAIL

.

Radio Indications of Lost Bluetooth Connection

The radio shows when the device has a Bluetooth connection. Below is the scenario and radio indications when the connection is interrupted.

The starts blinking for up to 10 seconds. You hear a decremental-pitched tone. The display shows

<Device Type>

alternating with

CON LOST

.

If the Bluetooth device successfully re-connects before the Bluetooth Drop Timer expires, the display shows momentary

<Device Type> CONNCTED

, and

shows persistently, or if the Bluetooth device fails to re-connect within 10 seconds, the blinking is replaced by a persistent .

Standard Pairing Feature

Note:

Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by

a qualified radio technician. Check with your dealer or system administrator for more information.

Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk time power consumption, not the Standby time consumption.

The Bluetooth Standard Pairing feature enables your

Bluetooth enabled radio to search for other Bluetooth enabled and discoverable device. Once the device is discovered, your radio automatically pairs with the device.

This feature also enables your Bluetooth enabled radio to be visible to another Bluetooth enabled device and receive request to pair from other device.

Searching and Pairing the Bluetooth Device

Ensure the Bluetooth on your device is turned to On and is set to

Discoverable

in order to enable your radio to detect your device in Bluetooth.

Bluetooth Search in Bluetooth Standard Pairing method is used to scan for other Bluetooth devices nearby. It is set to off by default.

The radio only search for HSP devices and Motorola

MCW & OCW accessories. Radio will filter out other profiles.

Press the preprogrammed

Bluetooth Inquiry

On/Off

button, to enable the

Bluetooth Search

feature.

One of the following scenarios occurs:

• If successful, the display shows

SRCH ON followed by

SRCH END

when the radio is pairing with a device found. The display shows

<Device Name> PAIRED

to indicate pairing is complete.

• The display shows

SRCH END

when the search timer expires without pairing with any device.

Repeat this step.

One of the following scenarios occurs:

• The radio continues to connect to the device. If the connecting process is successful, the radio sounds an incremental-pitched tone. The display shows

<Device Type>CONNCTED

, and the

Bluetooth icon turns from b to a.

• If the device already has pairing records and the connecting process fails, the radio sounds a short,

71

English

low-pitched tone. The display shows

<Device

Type> CON FAIL

.

• If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows

<Device

Type> UNPAIRED

.

Turning Bluetooth Visibility On

Turning Bluetooth visibility to on enables other

Bluetooth devices to search for your radio. The visibility of the Bluetooth is set to off by default.

Turn Bluetooth visibility on via the preprogrammed button.

a) Press and hold the preprogrammed

Bluetooth

Inquiry On/ Off

button for three seconds to enable the Bluetooth visibility feature.

One of the following scenarios occurs:

• Keep holding the button although you hear a short, medium-pitched tone with the display shows momentary

VISIBLE

.

[2]

This indicates the visibility is turned on successfully.

• If the visibility fails to turn on, the display shows

VISIBLTYFAILED

.

• When the timer expires, the display shows

VISI OFF

.

Receiving Pairing Request from other Devices

Turn on your radio Bluetooth Visible mode.

Your radio automatically accept the request and pair with any request received from other device.

Turning On the Bluetooth Audio (Routing the Audio from the Radio to the Headset)

Turning on the Bluetooth audio via the preprogrammed button: a) Press the preprogrammed

Bluetooth Audio

Reroute

button to route the audio from the radio to the headset.

A short, medium-pitched tone sounds. The display shows

HDSET ON

.

72

2

Releasing the preprogrammed button turns off the Visibility mode.

English

Turning Off the Bluetooth Audio (Routing the Audio from the Headset to the Radio)

Turning off the Bluetooth audio via the preprogrammed button: a) Press the preprogrammed

Bluetooth Audio

Reroute

button to route the audio from the headset to the radio.

A short, medium-pitched tone sounds. The display shows

SPKR ON

.

Adjusting the Volume of the Radio from Bluetooth

Audio Device

Ensure that the Bluetooth audio device is connected to the radio.

Your radio can only control the volume of MCW and

OCW Bluetooth enabled audio device. If the radio is paired with other Bluetooth enabled audio device, its volume is independent from the APX radio. In this case, the volume is only adjustable on the device.

Adjust volume up/down on the Bluetooth audio device.

The radio display shows

VOL XX

and sounds a short, medium-pitched tone.

Clearing All Bluetooth Devices Information

Clearing all Bluetooth devices information via the preprogrammed

Bluetooth On/Off

button: a) Long press the preprogrammed

Bluetooth

On/Off

button.

You hear a short, medium-pitched tone. The display shows

PLS WAIT

to indicate clearing is in progress.

If successful, the display shows

ALL CLR

.

If unsuccessful, you hear the radio sounds a short, low-pitched tone.The display shows

CLR

FAIL

.

Note:

If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.)

Programming Over Project 25 (POP 25)

(ASTRO 25 and ASTRO Conventional)

This feature enables configuration data to be upgraded to your radio over-the-air. This feature retains full use of the radio during the configuration

73

English

data transfer without interrupting communication. The upgrade pauses to give priorities to voice call, and continues after the voice call ended.

Once a configuration upgrade is downloaded to your radio, you can install new changes immediately or delay changes to be installed on the radio when it is being powered up.

Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.

74

Voice Announcement

This feature enables the radio to audibly indicate the current feature mode, zone or channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display.

Each voice announcement is within a limit of three seconds maximum. The sum duration of all different voice announcements in a radio shall be no more than 1000 seconds.

Note:

This feature must be preprogrammed by a qualified radio technician.

English

Check with your agent if Voice Announcement is available for the feature you need.

The two options of priority for the Voice

Announcement available are:

High

Enables the voice of the feature to announce even when the radio is receiving calls.

Low

Disables the voice of the feature from announcing when the radio is receiving calls.

You hear a voice announcement when the features below are preprogrammed in the radio.

• The radio powers up. The radio announces the current zone and channel it is transmitting.

• Press the preprogrammed voice announcement button (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting.

Note:

Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority.

All the three programmable buttons at the side of the radio support this feature.

• Change to a new zone. The radio announces the current zone and channel it is transmitting.

• Change to a new channel remaining within the current zone. The radio announces the current channel.

• Press either the preprogrammed button or switch of the radio to launch or terminate Scan,

Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation.

Site Selectable Alerts (ASTRO 25)

A Site Selectable Alert (SSA) is an Intelligent Lighting indicator together with audio alert sent to radios at a site or a few sites to notify the users when there is a special situation that they need to be aware of. Only authorized radios are enabled to send SSA.

Upon the activation of a SSA, the receiving radios display the alert alias and generate the periodic alert tone.

Note:

Alert alias, alert tone, and alert period can be preprogrammed. Alert period is the duration for the radio to repeat the alert tone. An interval of 5 seconds might impact the battery life of the radio. Check with your dealer or system administrator for more details.

When mixing SSA with received voice audio, the SSA alert is reduced in volume to ensure that the voice message is still heard clearly. Therefore, it is important that the SSA audio files are created with clear loud audio to ensure they can still be heard clearly when played at reduced levels.

Utilities

Using the Flip Display

This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still in the carry holder attached to your belt.

To flip the display, press and hold the preprogrammed

Light/Flip

button

Selecting a Basic Zone Bank

The Basic Zone Select feature must to be preprogrammed to the

3-position A-B-C

switch, while the Basic Zone Bank feature must be preprogrammed to any

side

button or

Top (Orange)

button before you can use this feature.

75

English

This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions.

Use the preprogrammed

Basic Zone Bank

button to toggle the position between Bank 1 and Bank 2.

The top display shows the status icons (

A

,

B

,

C

,

D

,

E

or

F

) or the zone name based on the bank and switch position selected.

Note:

See the

Basic Zone Bank 1

and

Basic Zone

Bank 2

icons for more information on the status icons.

76

Selecting an Enhanced Zone Bank

This feature is created in order to allow users to communicate in more zones. An

Enhanced Zone

Bank (EZB)

consists of three zones. This also means each icon

A

,

B

,

C

, ... or

Y

consist of three zones. You can use the preprogrammed

3-position A-B-C

switch to select the first, second or third zone in an EZB.

This feature allows user to navigate from up to 75 zones in 25 EZBs.

Note:

The Zone Select feature must to be preprogrammed to the

3-position A-B-C

switch, while the Enhanced Zone Bank feature must be preprogrammed to any

side

button or

Top (Orange)

button before you can use this feature.

1

Press the preprogrammed

EZB Up

or

EZB Down

button to scroll the EZB up or down or press and hold the preprogrammed

EZB Up

or

EZB Down

button to fast scroll the EZB up or down.

2

Turn the

3-Position A/B/C

Switch to select the first, second or third zone in the selected EZB.

Selecting the Power Level

Note:

This feature must be preprogrammed by a qualified radio technician.

This feature enables you to reduce the transmit power level for specific case that requires a lower power level. You can select the power level at which your radio transmits. The radio always turns on to the default setting. These reduced transmit power level settings do not affect the receiving performance of your radio, nor diminish the overall quality of the audio and data functionality of the radio given the following conditions.

Power level

Low

enables a shorter transmitting distance and to conserve power. Power level

High enables a longer transmitting distance.

English

Use the preprogrammed

Transmit Power Level

switch to toggle the power level between low and high power.

The display shows

LOW PWR

and the low power icon or the display shows

HIGH PWR

and the high power icon.

Controlling the Display Backlight

You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display or keypad difficult to read.

Note:

The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level.

Perform one of the following actions:

• To toggle the backlight on or off, press the preprogrammed

Light/Flip

button.

• To turn the backlight on, press any programmable radio controls or buttons.

Locking and Unlocking the Controls

You can lock the programmable buttons, switches and rotary knobs of your radio to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suit your usage.

1

Toggle the preprogrammed

Keypad/Control Lock

button or switch to on.

2

The display shows

CTRL LCK

.

3

To unlock the knobs and buttons, toggle again.

Turning Voice Mute On or Off

You can enable and disable voice transmission, if needed.

Turning Voice Mute on or off via the preprogrammed

Voice Mute

button: a) To turn the feature off or on, press the preprogrammed

Voice Mute

button.

The display shows momentary

VMUT OFF

, and you hear a short tone, indicating that the feature is disabled or the display shows momentary

VMUT ON

,

English

77

78

and you hear a short tone, indicating that the feature is enabled.

Using the Time-Out Timer

This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting.

If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone.

The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician.

Note:

You hear a brief, low-pitched, warning tone four seconds before the transmission times out.

1

Hold down the

PTT

button longer than the preprogrammed time.

You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the

PTT

button.

2

Release the

PTT

button.

The timer resets.

3

To re-transmit, press the

PTT

button.

The time-out timer restarts and the LED lights up solid red.

Using Conventional Squelch Operation Features

This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise.

Analog Options

Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available

(preprogrammed) per channel.

Mode

Carrier squelch (C)

PL or DPL

Result

You hear all traffic on a channel.

The radio responds only to your messages.

Digital Options

One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information.

English

Option

Digital Carrier-Operated

Squelch (COS)

Normal Squelch

Selective Switch

Result

You hear any digital traffic.

You hear any digital traffic having the correct network access code.

You hear any digital traffic having the correct network access code and correct talkgroup.

Using the PL Defeat Feature

This feature allows you to override any coded squelch

(DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel.

Place the preprogrammed

PL Defeat

switch in the

PL Defeat position.

One of the following scenarios occurs:

• You hear any activity on the channel.

• The radio is muted if no activity is present.

Note:

When this feature is active, the Carrier

Squelch status indicator is displayed.

Digital PTT ID Support

This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher.

Your radio’s ID number is also automatically sent every time the

PTT

button is pressed. This is a perchannel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message.

Smart PTT Feature (Conventional Only)

Smart

PTT

is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations.

When smart

PTT

is enabled in your radio, you cannot transmit on an active channel.

If you try to transmit on an active smart-

PTT

channel, you hear an alert tone, and the transmission is

79

English

80

English inhibited. The LED lights up solid yellow to indicate that the channel is busy.

The following table shows the variations of smart

PTT

:

Mode

Transmit Inhibit on Busy

Channel with

Carrier

Transmit Inhibit on Busy

Channel with

Wrong Squelch

Code

Quick-Key

Override

Description

You cannot transmit if any traffic is detected on the channel.

You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented.

This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two

PTT

button presses within the preprogrammed time limit.

Transmit Inhibit

This feature is available for APCO 25 trunking, Type II trunking and Conventional operations for all APX radios.

When Transmit Inhibit feature is enabled, the radio stops all transmission including voice and data. The radio could receive messages but not replying the acknowledgement request of the received message.

User could physically control the transmission of the radio especially during operation in hazardous environments with this feature. An environment is considered hazardous when the power emitted by the radio power amplifier could initiate an explosion or other dangerous reactions.

When the Transmit Inhibit feature is disabled, the radio functions according to its normal operations.

The radio sounds alert tone when user enters or exits this feature and also when PTT is pressed.

Note:

Acknowledgement of any messages required from the radio is not transmitted if the Transmit

Inhibition is enabled.

Enabling Transmit Inhibition

Press the Transmit Inhibit programmable button.

Note:

If the user has disabled TX Inhibit via the menu and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value.

The display shows

Tx inhibit on

. You hear a sequence of short, low

‐ high tones to indicate transmission is inhibited.

Pressing

PTT

triggers the radio sounds a constant short, low

‐ pitched tone (reject tone).

Note:

The status of the Transmit Inhibit does not change after the radio powers up.

Disabling Transmit Inhibition

Press the Transmit Inhibit programmable button.

Note:

If the user has disabled TX Inhibit via the softkey and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value.

The display shows

Tx inhibit off

. You hear a sequence of short, high

‐ low tone (Transmit Inhibit

Off tone) to indicate transmission is back to normal operation.

English

81

Helpful Tips

Radio Care

Caution:

• Your radio casting has a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers.This could create leak paths into the radio and the radio’s submergibility will be lost.

A

82

English

• Your radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours.

Exceeding either maximum limit may result in damage to the radio.

• Elastomer technology materials used for seals in rugged portable radios can age with time and environmental exposure.

Therefore, Motorola recommends that rugged radios be checked annually as a preventive measure in order to assure the watertight integrity of the radio. Motorola details the disassembly, test, and reassembly procedures along with necessary test equipment needed to inspect, maintain and troubleshoot radio seals in the radio’s service manual.

• If the radio battery contact area has been submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio.

• If the radio has been submerged in water, shake the radio well so that any water that may be trapped inside the speaker grille and microphone port can be removed.

Otherwise, the water will decrease the audio quality of the radio.

• Do

not

disassemble the radio. This could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician.

Cleaning Your Radio

Caution:

Do

not

use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures.

Do

not

submerge the radio in the detergent solution.

To clean the external surfaces of your radio, follow the procedure described next.

1

Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution).

2

Apply the solution sparingly with a stiff, nonmetallic, shortbristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth.

3

Clean battery contacts with a lint-free cloth to remove dirt or grease.

Proper Ways to Handle the Radio

• Do

not

pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna.

• Avoid subjecting the radio to an excess of liquids.

Do not submerge the radio unless it is a ruggedized.

• Avoid subjecting the radio to corrosives, solvents or chemicals.

• Do

not

disassemble the radio.

• Keep the accessory-connector cover in place until ready to use the connector. Replace the cover immediately once the accessory has been disconnected.

• When charging the radio using a wall mounted charger, the radio must be turned off. Otherwise, the Man Down Alert and Emergency may be accidentally triggered.

Radio Service and Repair

Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating

83

English

84

condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer.

Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for an additional period of either one or two years beyond the normal expiration date of the standard warranty. For more information about ESP, contact the Motorola Radio Support Center at 3761

South Central Avenue, Rockford, IL 61102 (800)

227-6772 / (847)725-4200.

Battery Care

Battery Charge Status

Your radio can indicate the battery’s charge status through:

• the LED and sounds.

• the fuel gauge icon on the display.

English

LED and Sounds

When your battery is low:

• the LED blinks red when the

PTT

button is pressed.

• you hear a low-battery “chirp” (short, high-pitched tone).

Fuel Gauge Icons

A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one.

Gauge Battery Charge

76% to 100% full

[3]

51% to 75%

[3]

26% to 50%

[3]

Gauge Battery Charge

11% to 25%

[3]

10% or less (at 10%, the gauge begins blinking)

Battery Recycling and Disposal

In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling

Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers participate in this program.

For the of the drop-off facility closest to you, access

RBRC's Internet web site at

www.rbrc.com

or call

1-800-8-BATTERY. This internet site and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies.

3

These are for IMPRES

battery operation only.

English

85

Accessories

The accessory link below is for APX radios. Not all accessories are FCC certified to operate with all APX models and/or bandsplits. Please refer to the specific

APX radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility.

http://www.motorolasolutions.com/APX

Note:

GPS only antenna is only used in either a single band UHF or 700/800 application where the

Public Safety Microphone (PSM) is used with the corresponding PSM antenna. This antenna is only for

GPS reception and cannot be used for receive/ transmit operation at UHF, VHF or 700/800. This antenna is never to be used on the PSM.

86

English

Maritime Radio Use in the VHF

Frequency Range

Special Channel Assignments

Emergency Channel

If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the

United States Coast Guard. Transmit the following information, in this order:

1

“MAYDAY, MAYDAY, MAYDAY.”

2

“THIS IS _____________________, CALL SIGN

__________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.

3

Repeat “MAYDAY” and the name of the vessel.

4

“WE ARE LOCATED AT

_______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:

• latitude and longitude

• bearing (state whether you are using true or magnetic north)

• distance to a well-known landmark

• vessel course, speed or destination

5

State the nature of the distress.

6

Specify what kind of assistance you need.

7

State the number of persons on board and the number needing medical attention, if any.

8

Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc.

9

“OVER.”

10

Wait for a response.

11

If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you.

Non-Commercial Call Channel

For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use

VHF Channel 9

.

Operating Frequency Requirements

A radio designated for shipboard use must comply with Federal Communications Commission Rule Part

80 as follows:

87

English

88

English

• on ships subject to Part II of Title III of the

Communications Act, the radio must be capable of operating on the 156.800 MHz frequency.

• on ships subject to the Safety Convention, the radio must be capable of operating:

• in the simplex mode on the ship station transmitting frequencies specified in the

156.025 – 157.425 MHz frequency band, and

• in the semiduplex mode on the two frequency channels specified in the table below.

Note:

Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast

Guard.

Table 1: VHF Marine Channel List

Channel

Number

Frequency (MHz)

Transmit Receive

11

12

13**

14

15**

16

17**

7

8

9

10

*

4

1

2

5

6

156.550

156.600

156.650

156.700

156.750

156.800

156.850

156.050

156.100

156.150

156.200

156.250

156.300

156.350

156.400

156.450

156.500

156.550

156.600

156.650

156.700

156.750

156.800

156.850

160.

6

50

160.700

160.750

160.800

160.850

160.950

156.450

156.500

63

*

65

28

60

*

62

24

25

26

27

18

19

20

*

22

*

157.400

156.025

156.075

156.125

156.175

156.225

156.275

156.900

156.950

157.000

157.050

157.100

157.150

157.200

157.250

157.300

157.350

162.000

160.625

160.675

160.725

160.775

160.825

160.875

161.500

161.550

161.600

161.650

161.700

161.750

161.800

161.850

161.9

0

0

161.950

*

*

*

77**

78

79

80

73

74

75

76

66

67**

68

69

71

72

156.325

156.375

156.425

156.475

156.575

156.625

156.675

156.725

***

***

156.875

156.925

156.975

157.025

157.0

7

5

157.125

157.175

161.525

161.575

161.

6

25

161.675

161.725

161.775

160.925

156.375

156.425

156.475

156.575

156.675

156.725

***

***

English

89

84

85

86

87

88

157.225

157.275

157.325

157.375

157.425

161.825

161.875

161.925

161.975

162.025

Note:

*

Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

**

Low power (1 W) only.

***

Guard band.

Note:

A – in the Receive column indicates that the channel is transmit only.

90

Declaration of Compliance for the Use of

Distress and Safety Frequencies

The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3.

English

Technical Parameters for Interfacing External

Data Sources

Input

Voltage

(Volts

Peak-topeak)

RS232

18V

Max Data

Rate

28 kb/s

Impedance

5k ohm

USB

3.6V

12 Mb/s

90 ohm

SB9600

5V

9.6 kb/s

120 ohm

Glossary

This glossary is a list of specialized terms used in this manual.

ACK

Active Channel

Analog Signal

ARS

ASTRO 25

ASTRO

Conventional

Autoscan

Bluetooth

Acknowledgment of communication.

A channel that has traffic on it.

An RF signal that has a continuous nature rather than a pulsed or discrete nature.

Automatic Registration Service

Motorola standard for wireless digital trunked communications.

Motorola standard for wireless digital conventional communications.

A feature that allows the radio to automatically scan the members of a scan list.

Bluetooth is an open wireless technology standard for exchanging data over short distances from fixed and mobile devices with high levels of security.

Bluetooth Pairing

Bluetooth pairing occurs when two bluetooth devices exchanged a passkey to form a paired Bluetooth wireless connection.

Call Alert

Privately page an individual by sending an audible tone.

Carrier Squelch

Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”.

Central Controller

A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the

English

91

92

English

Channel

operations of the trunked repeaters.

A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding.

Control Channel

In a trunking system, one of the channels that is used to provide a continuous, twoway/ data communications path between the central controller and all radios on the system.

Conventional

Typically refers to radio-toradio communications, sometimes through a repeater

(see Trunking).

Conventional

Scan List

COTS

Digital Private

Line (DPL)

A scan list that includes only conventional channels.

Commercial Off-The-Shelf

A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone.

Digital Signal

Dispatcher

Dynamic

Regrouping

Failsoft

FCC

FM

Hang Up

An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature.

An individual who has radio system management duties.

A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other.

A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft.

Federal Communications

Commission.

Frequency Modulation

Disconnect.

Home screen

IV&D

KVL

LCD

LED

Li-Ion

Man Down

MCW

The first display information after the radio completes its self test.

Integrated Voice and Data

Key-variable loader: A device for loading encryption keys into the radio.

Liquid crystal display.

Light-emitting diode.

Lithium ion.

A life-saving feature that senses the radio user may be in trouble by monitoring the whether the radio is in a vertical or horizontal position or whether the radio is motionless. When this feature is triggered, the radio alerts the user with audio and visual alerts. It can also trigger

Emergency Alarm the Post-

Alert Timer is not cancelled.

Mission Critical Wireless

MDC

Monitor

Multi-System

Talkgroup Scan

List

Network Access

Code

NiMH

Non-Tactical/

Revert

Motorola Data Communication

Check channel activity by pressing the Monitor button. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed.

A scan list that can include both talkgroups (trunked) and channels (conventional).

Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites.

Nickel-metal-hydride.

The user talks on a preprogrammed emergency channel. The emergency alarm

93

English

94

English

OCW

OTAR

Page

is sent out on this same channel.

Operation Critical Wireless

Over-the-air rekeying.

Personality

A one-way alert, with audio and/or display messages.

A set of unique features specific to a radio.

Preprogrammed

Refers to a software feature that has been activated by a qualified radio technician.

Private

(Conversation)

Call

A feature that lets you have a private conversation with another radio user in the talkgroup.

Private Line (PL)

A sub-audible tone that is transmitted such that only receivers decoding the tone receives it.

Programmable

Refers to a radio control that can have a radio feature assigned to it.

PTT

Radio Frequency

(RF)

Repeater

Push-To-Talk. The

PTT

button engages the transmitter and puts the radio in transmit

(send) operation when pressed.

The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to

10,000,000 MHz).

A conventional radio feature, where you talk through a receive/transmit facility that retransmits received signals, in order to improve communications range and coverage.

Selective Switch

Any digital P25 traffic having the correct Network Access

Code and the correct talkgroup.

Squelch

Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off,

Standby

Status Calls

Tactical/ Non-

Revert

Talkaround

Talkgroup

unwanted signals before they are heard in the speaker.

An operating condition whereby the radio’s speaker is muted but still continues to receive data.

Pre-defined text messages that allow the user to send a conditional message without talking.

The user talks on the channel that was selected before the radio entered the emergency state.

Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications.

An organization or group of radio users who communicate with each other using the same communication path.

Trunking

Trunking Priority

Monitor Scan List

USK

Zone

The automatic sharing of communications paths between a large number of users (see

Conventional).

A scan list that includes talkgroups that are all from the same trunking system.

Unique Shadow Key.

A grouping of channels.

English

95

Limited Warranty

MOTOROLA COMMUNICATION PRODUCTS

96

I. WHAT THIS WARRANTY COVERS AND FOR

HOW LONG:

MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the MOTOROLA manufactured

Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

ASTRO APX 6000XE

Portable Units

Product Accessories

One (1) Year

One (1) Year

MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or

English boards are warranted for the balance of the original applicable warranty period. All replaced parts of

Product shall become the property of MOTOROLA.

This express limited warranty is extended by

MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA.

Unless made in a separate agreement between

MOTOROLA and the original end user purchaser,

MOTOROLA does not warrant the installation, maintenance or service of the Product.

MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the

Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique,

MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.

II. GENERAL PROVISIONS:

This warranty sets forth the full extent of

MOTOROLA'S responsibilities regarding the Product.

Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy.

THIS WARRANTY IS GIVEN IN LIEU OF ALL

OTHER EXPRESS WARRANTIES. IMPLIED

WARRANTIES, INCLUDING WITHOUT LIMITATION,

IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO THE DURATION OF THIS

LIMITED WARRANTY. IN NO EVENT SHALL

MOTOROLA BE LIABLE FOR DAMAGES IN

EXCESS OF THE PURCHASE PRICE OF THE

PRODUCT, FOR ANY LOSS OF USE, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS,

LOST PROFITS OR SAVINGS OR OTHER

INCIDENTAL, SPECIAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR

INABILITY TO USE SUCH PRODUCT, TO THE

FULL EXTENT SUCH MAY BE DISCLAIMED BY

LAW.

III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION

OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LIMITATION ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO

THE ABOVE LIMITATION OR EXCLUSIONS MAY

NOT APPLY.

This warranty gives specific legal rights, and there may be other rights which may vary from state to state.

IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location.

Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at

1-800-927-2744 US/Canada.

97

English

98

V. WHAT THIS WARRANTY DOES NOT

COVER:

1

Defects or damage resulting from use of the

Product in other than its normal and customary manner.

2

Defects or damage from misuse, accident, water, or neglect.

3

Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.

4

Breakage or damage to antennas unless caused directly by defects in material workmanship.

5

A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.

6

Product which has had the serial number removed or made illegible.

7

Rechargeable batteries if:

• any of the seals on the battery enclosure of cells are broken or show evidence of tampering.

• the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.

8

Freight costs to the repair depot.

9

A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with

MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from

MOTOROLA.

10

Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the

Product.

11

Normal and customary wear and tear.

VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against

English

the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

1

that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim,

2

that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise, and

3

should the Product or parts become, or in

MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United

States patent, that such purchaser will permit

MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.

MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product.

The foregoing states the entire liability of

MOTOROLA with respect to infringement of patents by the Product or any parts thereof.

Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under

MOTOROLA patent rights or copyrights.

English

99

VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of

Illinois, U.S.A.

100

VIII. For Australia Only:

This warranty is given by Motorola Solutions Australia

Pty Limited (ABN 16 004 742 312) of Tally Ho

Business Park, 10 Wesley Court. Burwood East,

Victoria.

Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Motorola Solutions Australia’s limited warranty above is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website:

http://www.motorolasolutions.com/XA-EN/Pages/

Contact_Us

for the most updated warranty terms.

English

APX6000XE_M1_BackCover_HalfLetter_P299C.fm Page 1 Monday, November 3, 2014 4:27 PM

APX6000XE_M1_BackCover_HalfLetter_P299C.fm Page 2 Monday, November 3, 2014 4:27 PM

Motorola Solutions, Inc.

1303 East Algonquin Road

Schaumburg, Illinois 60196 U.S.A.

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.

All other trademarks are the property of their respective owners.

© 2011–2014 Motorola Solutions, Inc. All rights reserved.

November 2014.

*68012003047*

68012003047-HA

advertisement

Related manuals

advertisement

Table of contents