BT-LH900P

Add to My manuals
28 Pages

advertisement

BT-LH900P | Manualzz

Liquid Crystal Video Monitor

BT-LH900

P

POWER INPUT MENU

EXIT

HD ZOOM BLUE FUNCTION

ENTER

PEAK/PHASE CHROMA BRIGHT CONTRAST

Before attempting to connect, operate or adjust this product, please read these instructions completely.

2

For your safety

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (service) instructions in the literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE AND

KEEP THIS EQUIPMENT AWAY FROM ALL

LIQUIDS—USE AND STORE ONLY IN

LOCATIONS WHICH ARE NOT EXPOSED TO

THE RISK OF DRIPPING OR SPLASHING

LIQUIDS, AND DO NOT PLACE ANY LIQUID

CONTAINERS ON TOP OF THE EQUIPMENT.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD AND ANNOYING INTERFERENCE,

USE THE RECOMMENDED ACCESSORIES

ONLY.

FCC Note:

This device complies with Part 15 of the FCC Rules.

To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications.

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Notice (U.S.A.only):

This product has a fluorescent lamp that contains a small amount of mercury.

It also contains lead in some components.

Disposal of these materials may be regulated in your community due to environmental considerations.

For disposal or recycling information please contact your local authorities, or the

Electronics Industries Alliance:

<http://www.eiae.org.>

CAUTION:

Do not install or place this unit in a bookcase, built-in cabinet or any other confined space in order to maintain adequate ventilation. Ensure that curtains and any other materials do not obstruct the ventilation to prevent risk of electric shock or fire hazard due to overheating.

indicates safety information.

Contents

Precautions for use . . . . . . . . . . . . . . . 3

Introduction . . . . . . . . . . . . . . . . . . . . . . 4

Parts and their functions . . . . . . . . . . . 5

Relocating the main controls . . . . . . . 8

Supplying the power . . . . . . . . . . . . . . 9

Cosmetic screws . . . . . . . . . . . . . . . . 10

How to use the on-screen menus . . . 11

Menu operations . . . . . . . . . . . . . . . . . 13

User data . . . . . . . . . . . . . . . . . . . . . . . 14

MAIN MENU . . . . . . . . . . . . . . . . . . . . . 15

REMOTE specifications . . . . . . . . . . . 22

Error and warning displays . . . . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . 24

Maintenance and inspections . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . 25

Precautions for use

This product has been specially designed for commercial use. As such, it should be used and operated only by persons with related expertise.

¥

The liquid crystal parts are fabricated using high-precision technology. The screen has effective pixels that cover more than 99.99% of its area, but pixels may be missing or remain permanently lighted (red, blue and/or green) in less than 0.01% of the area. This is not indicative of malfunctioning.

¥

The panel which protects the liquid crystal display has been specially treated.

Do not wipe it with hard cloths or rub it heavily as this will damage the surface of the panel.

¥

If a still image is displayed continuously for a long period of time, the image may be burnt onto the screen for some time. (The shadow of the image will usually disappear after moving images are displayed for while.)

¥

The response speed and brightness of the liquid crystals will vary with the surrounding temperature.

3

4

Introduction

Designed for use in broadcasting and commercial applications, the model BT-LH900P is a slim-line and lightweight liquid crystal video monitor with an 8.4-type liquid crystal screen.

For use, secure it in place by, for instance, installing it in a rack by using the optional rack-mounting adaptors BT-MA900G or mounting it on a tripod. (For details, refer to the instructions in the operation guide of the BT-MA900G.)

Slim design, light weight, compact size, low power consumption and driven by DC power

Since this monitor uses an LCD panel, it has a slim design, light weight and compact size. Furthermore, while supporting HD specifications, it has a low power consumption, and it can be operated using DC power: these are all features which make the monitor useful in outdoor locations.

Multiple formats supported

In addition to its two lines of SDI input connectors

(automatic HD/SD switching), the monitor provides one line each of component input connectors and composite input connectors.

Functions

The main controls can be relocated to the bottom surface or right panel of the main unit to support monitor specifications, viewfinder specifications and other applications.

The monitor comes with a film gamma correction function to support its use as the viewfinder for the AJ-

HDC27F. (For further details, consult with your dealer or a Panasonic Service Center.)

Waveform monitor functions provided

Marker functions and blue-only function incorporated

RS-232C external control, remote control using GPI connector enabled

Outline diagrams of monitor as seen from three sides

Wide viewing angle

The monitor can display excellent images over an angle extending for 170 degrees in both the top-bottom and leftright directions.

218 mm

High-definition images

At 1024 a 768 dots (XGA), the large number of screen pixels ensures a high color reproducibility and tonal range.

150 mm

Parts and their functions

1

3 HD ZOOM/X

button

This button is used to move the cursor or change settings while a menu is displayed.

If there is no menu display, it turns the HD ZOOM function ON or OFF. When the button is pressed, both the left and right sides of the images with a 16:9 aspect ratio produced by HD signals are cut off, and images with a 4:3 aspect ratio are displayed on the entire screen. When it is pressed, the original images are restored.

The HD zoom function does not work when images of

SD signals are displayed.

2 3 4

1

Tally lamps

In the above illustration, the R (red) tally lamp is shown on the left and the G (green) lamp appears on the right.

These tally lamps can be lighted by initiating the GPI

ON/OFF operation.

<Note>

When the monitor is used outdoors, it may be hard to see that the tally lamps are in fact lighted.

Controls 2, 3 and 4 can be separated from the monitor main unit as the main controls and relocated to the bottom surface or right panel of the main unit.

2

Power LED

This is the power LED. It lights while the power is ON.

1 2 3 4 5

INPUT MENU

EXIT

HD ZOOM BLUE FUNCTION

ENTER

3

Function buttons

1 INPUT button

This button is used to select the signal input. Each time it is pressed, the input channels are switched by one setting in the following sequence: SDI 1

> SDI 2

> VIDEO > YPBPR/RGB.

By means of the INPUT menu settings, the unused channels can be skipped.

2 MENU/EXIT button

This button is used to display the menus. When it is pressed while a menu is already displayed, the menu display is cleared or the menu at one hierarchical level above is restored.

When the button is pressed while a setting is being changed, the setting established prior to the change is restored, and the menu at one hierarchical level above is restored.

HD ZOOM

4 BLUE/W

button

This button is used to move the cursor or change settings while a menu is displayed.

If there is no menu display, it turns the blue-only function ON or OFF. When this function is set to ON, only the blue components among the RGB components are displayed.

5

6

Parts and their functions

5 FUNCTION/ENTER button

This button is used to enter changes or settings while a menu is displayed.

If there is no menu display, the button's function changes depending on which FUNCTION item on the menu is selected. One of the following three items can be selected. (Refer to page 19)

UNDEF:

No function is allocated to this item.

HV DELAY:

Image blanking is displayed. Each time the button is pressed, the blanking display is switched by one setting in the following sequence: H blanking display

> V blanking display > H and V blanking display

> no blanking display.

WFM ON/OFF: The Y signal (luminance) waveform is displayed at the bottom right of the image. When the button is pressed again, the display is cleared.

When waveforms are displayed in the

16:9 mode, the image displayed on the screen moves to the upper part of the screen so that it will not be superimposed onto the waveform display.

>

WFM

WFM function OFF WFM function ON

The image remains unchanged in the 4:3 mode.

>

WFM

WFM function OFF WFM function ON

<Notes>

In order for this function to be used, it is necessary to select WFM as the FUNCTION item setting on the

SYSTEM CONFIG screen, and then select FUNCTION as the WFM item setting.

The WFM function is a simplified one and, as such, finely detailed waveforms may not be displayed accurately.

In addition, differences in the input signal format or input function may result in the display having a different horizontal width.

1 2 3 4

PEAK/PHASE CHROMA BRIGHT CONTRAST

4 Image controls

These controls are used to adjust the peaking/color phase, chroma, brightness and contrast. When a control is pushed in, it pops out to enable adjustment. When a numerical value is changed from the default setting, the lamp to the left of the control lights.

The adjustments performed using these controls are valid only when the controls are in the "out" position, and when a control is pushed back in, the value adjusted by that control is returned to its default setting.

1 PEAK/PHASE (PEAKING/PHASE)

This control is used to adjust the peaking or phase.

Which of these is to be adjusted is set using the

PEAKING/PHASE item on the SYSTEM CONFIG screen.

PEAKING

This function is selected when the monitor is to be used as a viewfinder.

It is used to set the edge sharpness. Any value from 0 to 30 can be set: the higher the value, the sharper the edges. The default setting is 0.

PHASE

This function is selected when the monitor is to be used as a monitor.

It is used to set the color phase of the screen. Any value from 0 to 60 can be set. The default setting is 30.

<Notes>

When the blue-only function is ON, the control functions as the PHASE control regardless of the setting.

The color phase cannot be adjusted when RGB signals are input.

2 CHROMA

This control is used to adjust the image chroma. Any value from 0 to 60 can be set. The default setting is

30.

<Note>

The chroma cannot be adjusted when RGB signals are input or when the MONO setting is ON.

3 BRIGHT

This control is used to adjust the image brightness.

Any value from 0 to 60 can be set. The default setting is 30.

However, the brightness cannot be adjusted when blanking is displayed using the HV DELAY function.

4 CONTRAST

This control is used to adjust the image contrast. Any value from 0 to 60 can be set. The default setting is

50.

Parts and their functions

?

4

6

5

Y/G

P

B

/B

P

R

/R

SYNC

CONTROL

GPI

POWER

VIDEO

IN

OUT

SDI 1

IN

SDI 2

IN

SWITCHED

OUT

DC IN

RS-232C

9

:

;

<

=

>

? @ 7 8

4 Battery holder

This holder is used with a battery made by Anton Bauer.

5 Analog component/RGBS connectors

These are the BNC input connectors for the analog component (Y/Pb/Pr) or RGBS signals. When RGB signals are supplied, external sync (gen-lock) can also be used.

< SDI output connector

The SDI signals are output from this connector. It is the switched output of the ; SDI input connectors.

The signals displayed on the screen, whether they are the ones supplied to the SDI 1 connector or SDI 2 connector, are output.

However, the switched output signals are not output when the component or video input signals have been selected.

6 Main controls dedicated connector

The cable from the main controls is connected here.

<Note>

The monitor is shipped with the cable disconnected from the connector. Prior to use, therefore, check out the shape of the cable connector and plug it properly into this connector.

7 GPI connector

When GPI signals are connected here, external operations can be performed.

8 RS-232C connector

External operations can be performed under the RS-

232C standard.

9 VIDEO IN connector

The video input signals are supplied to this connector.

:

VIDEO OUT connector

The video signals are output from this connector.

Signals are passed through the 9 VIDEO IN connector and output from this connector.

= Power switch

This is the power switch.

> External DC power socket

The external DC power source is connected here. When a DC power supply is connected concurrently with the battery, the external power input takes precedence.

? Tripod fastening screws

Two screws (UNC3/8-16 compatible) for securing a tripod are provided each on the top of the monitor and at its bottom where the main controls are removed.

A removable screw spacer is provided in one of the screw holes in the bottom of the monitor, and this supports a UNC1/4-20 screw. To secure the tripod, use the hole that fits the diameter of the fastening screw on the tripod.

@ Light control switch

This is not used on this monitor.

; SDI input connectors

The SDI input signals are supplied to these connectors which support automatic HD/SD switching.

7

8

Relocating the main controls

The main controls can be relocated to the bottom surface or right panel of the monitor depending on such factors as where and how the monitor will be used.

<Note>

Before relocating the main control, make absolutely sure that the power has been turned off.

1

Disconnect the cord connecting the main controls to the main unit.

Take hold of this part and pull it free to disconnect the cable.

4

Use the two screws to secure the main controls to the right panel.

2

Remove the screws on the right panel of the main unit.

5

Plug the cord connecting the main controls into the connector on the main unit and secure it.

<Note>

Using too much force to plug in the cord at the wrong insertion angle may damage the pins inside. Check out the shape of the connector before plugging it in.

Plug in the connector until it clicks into place.

3

Remove the two screws, and remove the main controls from the main unit. These two screws cannot be removed from the main controls themselves.

6

Secure the two screws, which were removed in step

2

, in the screw holes on the bottom of the monitor.

Supplying the power

An Anton Bauer, V-mount or other such type of battery pack or an AC power source can be used to power this monitor.

Using the Anton Bauer battery pack

1

Install the Anton Bauer type of battery pack.

Battery pack

Using a V-mount battery pack

1

Remove the battery holder.

Battery holder

2

Insert the battery pack and slide it in the direction of the arrow.

2

Install the accessory metal battery mount.

Metal battery mount

Release lever

<Reference>

To remove the battery pack, slide it in the opposite direction to the one in which it was attached while keeping the release lever on the battery holder pulled down all the way.

3

Secure the V-mount adapter using the four screws, and then secure the two screws of the connector section.

V-mount adapter

9

Supplying the power

Using an AC power supply

1

Connect the DC OUT connector on the AJ-B75 AC adapter to the DC IN socket on the unit.

AC adapter

AJ-B75 (optional accessory)

2

Set the power of the AC adapter to ON.

DC IN socket

3

Set the unit’s power switch to ON.

When using an external power supply other than the

AJ-B75 AC adapter, check the pin signals of its external

DC input connector and use the polarities correctly.

1

2 3

4

Pin no.

Signal

1

2, 3

4

GND

+12V

External DC input socket

<Notes>

Power from the AC adapter takes precedence when both a battery pack and AC adapter have been connected. It is also possible to attach/remove a battery while the AC adapter is being used.

When using the AC adapter, be absolutely sure to first set the power of the AC adapter to ON and then set the unit’s power switch to ON.

A voltage of 20V or more will not be indicated accurately on the battery voltage display.

Cosmetic screws

Screwsa4

A total of eight cosmetic screws are provided with the monitor for use at such times when the main controls have been relocated. (Refer to page 8)

Since these screws also serve to protect the internal mechanisms, do not leave the screw holes empty but place the screws inside them and tighten them up. Any screws which are not being used should be kept in a safe place.

Screwsa2

Screwsa2

10

How to use the on-screen menus

Four kinds of information—menus, status displays, image control settings and battery voltage—can be displayed on the screen.

Menu display

[MAIN MENU]

VIDEO CONFIG 4

SYSTEM CONFIG 4

OSD CONFIG 4

GPI 4

INPUT SELECT 4

CONTROL 4

XW

This display appears when the MENU/EXIT button is pressed. If no further action is taken for the next 120 seconds, the display will be automatically cleared.

The position where the display appears on the screen can be changed using the marker setting.

For details on the menu, refer to “MAIN MENU” (page 15).

Status display

1

2

3

SDI1 1080/60I

CRCC

1 Channel and signal format

The channel which has been selected—whether SDI 1,

SDI 2, VIDEO, YPBPR or RGB—is displayed here.

Indicated as the signal format is the format of the signals which have been input. However, "UNSUPPORTED

SIGNAL" will appear if signals which are not supported have been input.

Similarly, “UNSUPPORTED SIGNAL” will also appear if signals not selected as the FORMAT item setting on the

INPUT SELECT screen of the main menu are input even when those signals are supported.

For details on the signals supported and format displays, refer to page 12.

The status display information is displayed under the following conditions while the menu display is not on the screen.

When the input signals have been switched

When the input channel has been changed

When no signals are supplied

The display location and display time can be changed using the menu settings. When images are adjusted using the image controls while the status display information is on the screen, the display is cleared, and the settings adjusted by the controls are displayed instead.

2 Warning display

This appears when an error has occurred or when a special mode is being used.

CRCC This indicates a CRCC error, and it appears when the SDI signals contain an error.

FILM This appears when the film mode (FILM) has been selected as the GAMMA SELECT item setting on the VIDEO CONFIG screen of the main menu.

This appears when REMOTE has been selected as the CONTROL item setting on the

CONTROL screen of the main unit. The monitor controls will no longer function at this time.

3 Battery voltage display

This indicates the voltage level of the battery. If an Anton

Bauer digital battery is being used, its remaining level is indicated as a number of "[//]" blocks and as a percentage along with the voltage value.

11

How to use the on-screen menus

Image control display

[CONTRAST] 50

The image control information is displayed when an image has been adjusted using the image controls. (Refer to page

6)

It appears when a control has been pressed in so that it has popped out or when an adjustment is made by turning an already popped out control.

It is cleared when a control is pressed again and returned to its original position. It is also cleared when a popped out control is not touched for 10 seconds.

Battery voltage display

The battery voltage information is displayed all the time when ON has been selected as the BATTERY REMAIN item setting on the OSD screen of the main menu.

It indicates the voltage level of the battery. If an Anton

Bauer digital battery is being used, its remaining level is indicated as a number of “∫” blocks and as a percentage along with the voltage value.

Concerning the signal formats

Menu setting

AUTO

1080/60I

1080/50I

1080/30P

1080/25P

1080/24P

1080/24PsF

1035/60I

720/60P

720/60P ANAMO

576/50I

480/60P

480/60I

NTSC

PAL

All supported signals

1080/60I

1080/59.94I

1080/50I

1080/30P

1080/29.97P

1080/25P

1080/24P

1080/23.98P

1080/24PsF

1080/23.98PsF

1035/60I

1035/59.94I

720/60P

720/59.94P

720/60P

720/59.94P

576/50I

480/59.94P

480/59.94I

NTSC

PAL

Signals whose input is accepted Status display

The format of the input signals is displayed.

1080/60I

1080/59.94I

1080/50I

1080/30P

1080/29.97P

1080/25P

1080/24P

1080/23.98P

1080/24PsF

1080/23.98PsF

1035/60I

1035/59.94I

720/60P

720/59.94P

720/60P

720/59.94P

576/50I

480/60P

480/60I

NTSC

PAL

12

Menu operations

Menu operations

1

When the MENU/EXIT button is pressed, the main menu appears on the screen.

MENU/EXIT button

2

Use the HD ZOOM/X button and BLUE/W button to move the cursor, and select the desired menu using the

FUNCTION/ENTER button.

4

Use the HD ZOOM/X button and BLUE/W button to change the setting, and press the FUNCTION/ENTER button to enter the change.

Alternatively, the change will be canceled when the

MENU/EXIT button is pressed instead.

Displayed in green.

[MARKER]

MARKER SELECT GPI

MARKER 16:9 OFF

MARKER 4:3 OFF

MARKER BACK NORMAL

CENTER MARKER OFF

GPI PRESET1 80%

GPI PRESET2 80%

XW

5

Press the MENU/EXIT button to exit the menu settings.

[MAIN]

MARKER

4

VIDEO CONFIG 4

SYSTEM CONFIG 4

OSD CONFIG 4

GPI 4

INPUT SELECT 4

CONTROL 4

XW

3

Use the HD ZOOM/X button and BLUE/W button to align the cursor with the item to be changed, and press the FUNCTION/ENTER button. The setting is now displayed in green.

[MARKER]

MARKER 16:9 OFF

MARKER 4:3 OFF

MARKER BACK NORMAL

CENTER MARKER OFF

GPI PRESET1 80%

GPI PRESET2 80%

XW

13

User data

This monitor enables the menu settings and screen values which have been adjusted by the image controls to be saved in five user data files which can then be loaded as required.

The following data can be saved and loaded as user data files:

All menu settings (including the function settings of the buttons at the front of the monitor) with the exception of USER

MODE LOAD/SAVE

Screen values which have been adjusted by the image controls

Saving the user data

1

When the MENU/EXIT button is pressed, the main menu appears on the screen.

2

Using menu operations (see page 13), select USER

MODE SAVE on the SYSTEM CONFIG screen, and press the FUNCTION/ENTER button. The setting is now displayed in green.

Loading the user data

1

When the MENU/EXIT button is pressed, the main menu appears on the screen.

2

Using menu operations (see page 13), select USER

MODE LOAD on the SYSTEM CONFIG screen, and press the FUNCTION/ENTER button. The setting is now displayed in green.

[SYSTEM CONFIG]

BACK LIGHT 60

FUNCTION WFM

WFM FUNCTION

HD ZOOM FRONT

PEAKING PHASE PHASE

USER MODE LOAD FACTORY

1

USER MODE SAVE

XW

3

When the file whose data is to be saved is selected from the USER1 to USER5 files and the

FUNCTION/ENTER button is then pressed, the screen shown below appears.

[SYSTEM CONFIG]

BACK LIGHT 60

FUNCTION WFM

WFM FUNCTION

HD ZOOM FRONT

PEAKING PHASE PHASE

1

USER MODE LOAD

USER MODE SAVE USER1

XW

ENTER

Displayed in green.

3

When the file whose data is to be loaded is selected from the FACTORY or USER1 to USER5 files and the

FUNCTION/ENTER button is then pressed, the screen shown below appears.

If FACTORY is selected at this time, the data is restored to the factory settings.

[USER MODE SAVE]

USER1

YES

1

NO

XW

[USER MODE LOAD]

USER1

YES

1

NO

XW

4

Align the cursor with YES, and press the

FUNCTION/ENTER button.

4

Align the cursor with YES, and press the

FUNCTION/ENTER button.

14

MAIN MENU

Menu configuration

MAIN

MARKER

VIDEO CONFIG

SYSTEM CONFIG

OSD CONFIG

GPI

INPUT SELECT

CONTROL

GAMMA SELECT

COLOR TEMP.

SHARPNESS MODE

SHARPNESS H

SHARPNESS V

I-P MODE

MONO

SD ASPECT

MARKER SELECT

MARKER 16:9

MARKER 4:3

MARKER BACK

CENTER MARKER

GPI PRESET1

GPI PRESET2

BATTERY REMAIN

STATUS DISPLAY

CRCC MESSAGE

MENU POSITION

STATUS POSITION

ROTARY POSITION

SDI1

FORMAT

SDI2

FORMAT

VIDEO

FORMAT

YPBPR/RGB

MODE

FORMAT

COMPONENT LEVEL

RGB SYNC

BACKLIGHT

FUNCTION

WFM

HD ZOOM

PEAKING/PHASE

USER MODE LOAD

USER MODE SAVE

GPI1

GPI2

GPI3

GPI4

GPI5

GPI6

GPI7

GPI8

CONTROL

LOCAL ENABLE

BACKLIGHT TIME

15

MAIN MENU

Menu items

MARKER

Item Setting

MARKER SELECT

MENU

GPI

MARKER 16:9

MARKER 4:3

MARKER BACK

CENTER MARKER

OFF

4:3

13:9

14:9

95%

93%

88%

80%

OFF

95%

93%

88%

80%

NORMAL

HALF

BLACK

OFF

ON

Description

For setting whether the marker display settings are to be performed using the menu or from the GPI connector.

MENU: The operations are performed using the menu. Operations from the GPI connector are canceled.

GPI:

The operations are performed from the GPI connector. The settings established using the menu are canceled.

For selecting the type of marker used for

16:9 images.

OFF: No markers are displayed.

4:3: Markers indicating the 4:3 size are displayed.

13:9: Markers indicating the 13:9 size are displayed.

14:9: Markers indicating the 14:9 size are displayed.

95%: The 95% area markers are displayed.

93%: The 93% area markers are displayed.

88%: The 88% area markers are displayed.

80%: The 80% area markers are displayed.

<Note>

When 4:3 images are displayed, the setting of this item is not reflected.

For selecting the type of marker used for

4:3 images.

OFF: No markers are displayed.

95%: The 95% area markers are displayed.

93%: The 93% area markers are displayed.

88%: The 88% area markers are displayed.

80%: The 80% area markers are displayed.

<Note>

When 16:9 images are displayed, the setting of this item is not reflected.

For setting the background brightness of the markers.

NORMAL: The background is set to the

HALF:

normal brightness.

The background brightness is set to 50%.

BLACK:

The background brightness is set to 0%.

<Note>

The setting of this item is valid only when

4:3, 13:9 or 14:9 has been selected as the

MARKER 16:9 item setting.

For selecting whether to display the center marker.

OFF: The center marker is not displayed.

ON:

The center marker is displayed.

Item

GPI PRESET1

GPI PRESET2

4:3

13:9

14:9

95%

93%

88%

80%

Setting

4:3

13:9

14:9

95%

93%

88%

80%

Description

For setting the markers to be displayed if, when MARKER1 ON/OFF has been allocated to any item and GPI has been selected as the MARKER SELECT item setting on the GPI screen, the corresponding pin has been set to ON.

For details, refer to “REMOTE specifications” (page 22).

4:3: Markers indicating the 4:3 size are displayed.

13:9: Markers indicating the 13:9 size are displayed.

14:9: Markers indicating the 14:9 size are displayed.

95%: The 95% area markers are displayed.

93%: The 93% area markers are displayed.

88%: The 88% area markers are displayed.

80%: The 80% area markers are displayed.

For setting the markers to be displayed if, when MARKER2 ON/OFF has been allocated to any item and GPI has been selected as the MARKER SELECT item setting on the GPI screen, the corresponding pin has been set to ON.

For details, refer to “REMOTE specifications” (page 22).

4:3: Markers indicating the 4:3 size are displayed.

13:9: Markers indicating the 13:9 size are displayed.

14:9: Markers indicating the 14:9 size are displayed.

95%: The 95% area markers are displayed.

93%: The 93% area markers are displayed.

88%: The 88% area markers are displayed.

80%: The 80% area markers are displayed.

The underlined setting indicates the factory setting mode.

16

MAIN MENU

Types of markers

16:9 markers

(These appear when HD signals or when SD signals with a 16:9 aspect ratio are supplied.)

4:3 markers

(These appear when SD signals with a 4:3 aspect ratio are supplied.)

4:3 markers 13:9 markers 95% area markers 93% area markers

14:9 markers

Markers are displayed only in the form of vertical lines.

The shaded areas indicate what is set by the MARKER

BACK item.

88% area markers 80% area markers

Dotted lines are displayed as the markers.

Center marker

This appears at the center of the image.

95% area markers 93% area markers

Center marker

88% area markers 80% area markers

Dotted lines are displayed as the markers.

17

MAIN MENU

VIDEO CONFIG

Item Setting

GAMMA SELECT

GPI

NORMAL

FILM

COLOR TEMP.

SHARPNESS

MODE

SHARPNESS H

SHARPNESS V

USER

D93

D65

D56

HIGH

LOW

0

2

30

0

2

:

:

:

:

30

Description

For setting the gamma mode.

GPI:

This is the GPI setting. For details, refer to “REMOTE specifications” (page 22).

NORMAL: The normal gamma mode is established.

FILM:

The film mode that supports the

Varicam digital cine camera is established.

For setting the color temperature.

USER: Any setting from 0 to 63 (equivalent to a color temperature range from

3000 K to 9300 K) can be established.

D93:

This is equivalent to a color temperature of 9300 K.

D65:

This is equivalent to a color temperature of 6500 K.

D56:

This is equivalent to a color temperature of 5600 K.

<Note>

The color temperature can be set for each gamma mode (NORMAL, FILM).

For setting the image sharpness.

HIGH: The images are accentuated with fine edges.

LOW: The images are accentuated with

<Note>

thick edges.

The sharpness can be set for VIDEO and all other input channels.

For setting the image sharpness in the horizontal direction.

This item enables two settings, one for the

VIDEO input signals and one for other signals, to be stored in the memory.

<Notes>

While this item's setting is selected, the only information displayed on the screen is this item which appears at the bottom left regardless of the MENU POSI setting selected on the OSD screen.

The sharpness can be set for VIDEO and all other input channels.

For setting the image sharpness in the vertical direction.

This item enables two settings, one for the

VIDEO input signals and one for other signals, to be stored in the memory.

<Notes>

While this item's setting is selected, the only information displayed on the screen is this item which appears at the bottom left regardless of the MENU POSI setting selected on the OSD screen.

The sharpness can be set for VIDEO and all other input channels.

Item

I-P MODE

MONO

SD ASPECT

Setting

MODE2

MODE1

GPI

OFF

ON

GPI

16:9

4:3

Description

For switching the IP conversion mode.

MODE2: Movement compensation mode

MODE1: Normal mode

<Note>

This setting takes effect when progressive signals (1080/30P, 1080/25P, 1080/24P,

720/60P or 480/60P) are input.

For selecting monochrome images.

GPI:

This is the GPI setting. For details, refer to “Concerning the REMOTE specifications” (page 22).

OFF: Normal images

ON:

Monochrome images

<Notes>

No adjustments are possible when RGB signals are input.

When ON has been selected as this item's setting, the setting for the

CHROMA image control is fixed at 0.

When the setting is returned to OFF, the

CHROMA setting prior to the change is restored.

For setting the aspect ratio of the SD signals.

GPI : This is the GPI setting. For details, refer to “REMOTE specifications”

(page 22).

16:9 : The images are displayed with a

16:9 aspect ratio.

4:3 :

The images are displayed with a 4:3 aspect ratio.

The underlined setting indicates the factory setting mode.

18

MAIN MENU

SYSTEM CONFIG

Item

BACKLIGHT

FUNCTION

WFM

HD ZOOM

PEAKING/ PHASE

USER MODE

LOAD

:

0

60

Setting

WFM

GPI

GPI

ON/OFF

HV DELAY

UNDEF

FUNCTION

FRONT

PEAKING

PHASE

USER5

USER4

USER3

USER2

USER1

FACTORY

USER MODE SAVE USER5

USER4

USER3

USER2

USER1

Description

For adjusting the backlight brightness to a level from 0 to 60. The higher the setting, the brighter the backlight.

For setting the function to be allocated to the FUNCTION/ENTER button.

WFM ON/OFF: The Y signal (luminance) waveforms are displayed.

HV DELAY: The blanked parts of the

UNDEF:

images are displayed.

No function is allocated.

For selecting whether the Y signal

(luminance) waveforms are to be displayed using the FUNCTION/ENTER button or from the GPI connector.

FUNCTION: The waveforms are displayed using the FUNCTION/ENTER

GPI:

button.

The operations are performed from the GPI connector. For details, refer to “REMOTE specifications” (page 22).

For selecting whether the HD ZOOM function is to be operated using the HD

ZOOM/X button or from the GPI connector.

FRONT: The function is operated using the

GPI:

HD ZOOM/X button.

The operations are performed from the GPI connector. For details, refer to “REMOTE specifications”

(page 22).

For selecting the PEAKING or PHASE function for the image control.

PEAKING: The PEAKING function is allocated to the control.

PHASE: The PHASE function is allocated to the control.

For calling the file in which the user data is stored.

USER1-5:

These are the files in which the user has stored data. If the user data has not yet been stored, the settings are the same as the ones in the FACTORY file.

FACTORY: This file contains the factory settings.

For saving the user data.

The underlined setting indicates the factory setting mode.

OSD CONFIG

Item Setting

BATTERY REMAIN

OFF

ON

STATUS DISPLAY

CRCC MESSAGE

MENU POSITION

ROTARY

POSITION

CONTINUE

3SEC. OFF

OFF

OFF

ON

LT

CENTER

LB

RB

RT

STATUS POSITION LT

CENTER

LB

RB

RT

LB

CB

RB

RT

LT

CENTER

OFF

Description

For selecting whether to display the remaining battery charge.

OFF: The remaining charge is not displayed.

ON: The remaining charge is displayed.

For setting how long the status display is to remain on the screen.

CONTINUE: The status display appears continuously at all times.

3SEC.OFF: The status display appears for three seconds.

OFF: The status display does not appear.

For selecting whether a message is to be displayed when a CRCC error has been detected.

OFF: A CRCC error message is not displayed.

ON:

A CRCC error message is displayed.

For setting the menu display position.

LT: The menu is displayed at the top left.

CENTER:

The menu is displayed in the center.

LB: The menu is displayed at the bottom left.

RB: The menu is displayed at the bottom right.

RT: The menu is displayed at the top right.

For setting the status display position.

LT: The menu is displayed at the top left.

CENTER:

The menu is displayed in the center.

LB: The menu is displayed at the bottom left.

RB: The menu is displayed at the bottom right.

RT: The menu is displayed at the top right.

For setting the display position of the settings when images have been adjusted using the image controls.

LB: The settings are displayed at the bottom left.

CB: The settings are displayed below the center.

RB: The settings are displayed at the bottom right.

RT: The settings are displayed at the top right.

LT: The settings are displayed at the top left.

CENTER:

The settings are displayed in the center.

OFF: The settings are not displayed.

GPI

GPI1-8

Item Setting

UNDEF

MARKER1 ON/OFF

MARKER2 ON/OFF

MARKER BACK HALF

MARKER BACK BLACK

CENTER MARKER

INPUT SEL. SDI1

INPUT SEL. SDI2

INPUT SEL. VIDEO

INPUT SEL. YPBPR/RGB

SD ASPECT

HD ZOOM

BACKLIGHT MIN.

R.TALLY

G.TALLY

MONO ON/OFF

GAMMA SELECT

WFM ON/OFF

Description

For allocating particular functions to particular pins when remote control operations are to be performed using the GPI signals. For details, refer to

“REMOTE specifications”

(page 22).

19

MAIN MENU

INPUT SELECT

SDI1 * 1

Item

FORMAT

AUTO

1080/60I

1080/50I

1080/30P

1080/25P

1080/24P

1080/24PsF

1035/60I

720/60P

720/60P

ANAMO

576/50I

480/60I

Setting

OFF

ON

Description

For setting whether the SDI 1 signals can be selected when the channels are to be switched using the INPUT button.

OFF: The SDI 1 signals cannot be selected.

ON: The SDI 1 signals can be selected.

For selecting the signals whose input is to be accepted at the SDI 1 connector.

AUTO:

All supported signals are accepted.

1080/60I:

1080/60I or 1080/59.94I format signals are accepted.

1080/50I:

1080/50I format signals are accepted.

1080/30P:

1080/30P or 1080/29.97P format signals are accepted.

1080/25P:

1080/25P format signals are accepted.

1080/24P:

1080/24P or 1080/23.98P format signals are accepted.

1080/24PsF:

1080/24PsF or 1080/23.98PsF format signals are accepted.

1035/60I:

1035/60I or 1035/59.94I format signals are accepted.

720/60P:

720/60P or 720/59.94P format signals are accepted.

720/60P ANAMO:

720/60P or 720/59.94P format signals which support an anamorphic lens are accepted.

576/50I:

576/50I format signals are accepted.

480/60I:

480/59.94I format signals are accepted.

SDI2 * 1

Item

FORMAT

VIDEO *

FORMAT

YPBPR *

MODE

1

1

AUTO

1080/60I

1080/50I

1080/30P

1080/25P

1080/24P

1080/24PsF

1035/60I

720/60P

720/60P

ANAMO

576/50I

480/60I

OFF

ON

Setting

OFF

ON

Description

For setting whether the SDI 2 signals can be selected when the channels are to be switched using the INPUT button.

OFF: The SDI 2 signals cannot be selected.

ON: The SDI 2 signals can be selected.

For selecting the signals whose input is to be accepted at the SDI 2 connector.

The setting selection is the same as for the

SDI 1 FORMAT item.

AUTO

NTSC

PAL

OFF

ON

YPBPR

RGB

For setting whether the VIDEO signals can be selected when the channels are to be switched using the INPUT button.

OFF: The VIDEO signals cannot be selected.

ON: The VIDEO signals can be selected.

For selecting the signals whose input is to be accepted at the VIDEO connector.

AUTO:

All supported signals are accepted.

NTSC:

NTSC signals are accepted.

PAL:

PAL signals are accepted.

For setting whether the YPBPR/RGB signals can be selected when the channels are to be switched using the INPUT button.

OFF: The YPBPR/RGB signals cannot be selected.

ON: The YPBPR/RGB signals can be selected.

For switching between the YPBPR and

RGB analog signals.

YPBPR:

The analog signals are switched to

Y/Pb/Pr.

RGB:

The analog signals are switched to RGB.

*1

Up to three of these items can be set to OFF at the same time. Once the three items have been set to OFF, it is no longer possible to set a fourth item to OFF. It is not possible to set all the inputs to OFF.

The underlined setting indicates the factory setting mode.

20

MAIN MENU

INPUT SELECT

Item

FORMAT

COMPONENT

LEVEL

RGB-SYNC

Setting

AUTO

1080/60I

1080/50I

1080/30P

1080/25P

1080/24P

1080/24PsF

1035/60I

720/60P

576/50I

480/60P

480/60I

SMPTE

B75

G-ON

EXT

Description

For selecting the signals whose input is to be accepted in the YPBPR mode and in the

RGB mode.

The signals can be set for each mode, and when the MODE item setting is switched from YPBPR to RGB or vice versa, the mode is automatically switched so that the signal format which has been set for the mode now set is accepted.

AUTO:

All supported signals are accepted.

1080/60I:

1080/60I or 1080/59.94I format signals are accepted.

1080/50I:

1080/50I format signals are accepted.

1080/30P:

1080/30P or 1080/29.97P format signals are accepted. (This setting takes effect only when YPBPR is selected.)

1080/25P:

1080/25P format signals are accepted.

(This setting takes effect only when

YPBPR is selected.)

1080/24P:

1080/24P or 1080/23.98P format signals are accepted. (This setting takes effect only when YPBPR is selected.)

1080/24PsF:

1080/24PsF or 1080/23.98PsF format signals are accepted. (This setting takes effect only when YPBPR is selected.)

1035/60I:

1035/60I or 1035/59.94I format signals are accepted. (This setting takes effect only when YPBPR is selected.)

720/60P:

720/60P or 720/59.94P format signals are accepted.

576/50I:

576/50I format signals are accepted.

480/60P:

480/60P format signals are accepted.

480/60I:

480/59.94I format signals are accepted.

For selecting the input level of the Y/Pb/Pr signals.

SMPTE: This is selected when the signals are to be output from an MII VTR.

B75:

This is selected when the signals are to be output from a Betacam

VTR.

For switching the connector where the sync signal is to be accepted.

G-ON: This is selected when the sync signal has been superimposed onto the G signal.

EXT:

The sync signal is accepted at the

SYNC connector among the analog component/RGBS connectors.

CONTROL

Item

CONTROL

LOCALENABLE

BACKLIGHT TIME

Setting

LOCAL

REMOTE

DIS.

INPUT

Description

For selecting where the operations are to be initiated.

LOCAL:

Only operations initiated from the main controls can be performed.

Remote control operations cannot be performed.

REMOTE: Remote control operations can be performed, but no operations initiated by the main controls can be performed although there are a few exceptions to this.

<Notes>

When REMOTE has been selected, the

“ ” lock mark appears on the status display.

When REMOTE has been selected, only the settings of the CONTROL item and

LOCALENABLE item on the CONTROL screen can be changed as menu operations.

For selecting whether to enable the input to be switched to the main controls when

REMOTE has been selected.

DIS: When REMOTE has been selected, the input can no longer be switched to the main controls.

INPUT:Even when REMOTE has been selected, the input can be switched to the main controls.

For displaying the total operation time of the backlight.

The underlined setting indicates the factory setting mode.

21

REMOTE specifications

This monitor can be operated by remote control using the GPI connector and

RS-232C connector.

GPI connector

The items on the GPI screen correspond to the connector pins shown below.

Functions can be allocated to these pins on the GPI screen of the main menu. (Refer to page 19)

The functions allocated to the pins are enabled when the corresponding pin is shorted (ON) to the GND pin and disabled when it is left open (OFF).

5 4 3 2 1

9 8 7 6

Connector (9P)

Pin no.

1

4

5

2

3

8

9

6

7

Signal

GPI1

GPI2

GPI3

GPI4

GND

GPI5

GPI6

GPI7

GPI8

List of functions allocated

The function which can be allocated to the pins are listed below.

Function

Description

Operation condition

UNDEF

Not set (no function allocated)

MARKER1 ON/OFF This displays the markers which have been set by the

Level operation

GPI PRESET1 item on the MARKER screen. (Refer to page 16) However, it is not valid when MENU has been selected as the MARKER SELECT item setting on the

MARKER screen.

<Note>

When this function has been set to ON at the same time as MARKER2, MARKER1 takes precedence.

MARKER2 ON/OFF This displays the markers which have been set by the GPI

Level operation

PRESET2 item on the MARKER screen. (Refer to page

16) However, it is not valid when MENU has been selected as the MARKER SELECT item setting on the

MARKER screen.

MARKER BACK

HALF

Level operation

This sets the background brightness to 50% when 4:3,

13:9 or 14:9 has been selected for the GPI PRESET1 item setting on the MARKER screen. However, it is not valid when MENU has been selected as the MARKER

SELECT item setting on the MARKER screen.

MARKER BACK

BLACK

Level operation

This sets the background brightness to 0% when 4:3,

13:9 or 14:9 has been selected for the GPI PRESET1 item setting on the MARKER screen. However, it is not valid when MENU has been selected as the MARKER

SELECT item setting on the MARKER screen.

<Note>

When this function has been set to ON at the same time as MARKER BACK HALF, MARKER BACK BLACK takes precedence.

CENTER MARKER

This displays the center marker.

However, it is not valid when MENU has been selected

Level operation

as the MARKER SELECT item setting on the MARKER screen.

<Note>

When any other markers are displayed, the center marker is superimposed onto the same display.

Function

Description

Operation condition

INPUT SEL. SDI1

Edge operation

This switches the input channel to SDI 1.

<Note>

This function is not valid when OFF has been selected as the SDI 1 item (see page 20) setting on the FORMAT screen.

INPUT SEL. SDI2

Edge operation

This switches the input channel to SDI 2.

<Note>

This function is not valid when OFF has been selected as the SDI 2 item (see page 20) setting on the FORMAT screen.

INPUT SEL. VIDEO

This switches the input channel to VIDEO.

Edge operation

<Note>

This function is not valid when OFF has been selected as the VIDEO item (see page 20) setting on the FORMAT screen.

INPUT SEL.

YPBPR/RGB

Edge operation

This switches the input channel to ANALOG.

<Note>

This function is not valid when OFF has been selected as the YPBPR/RGB item (see page 20) setting on the

FORMAT screen.

SD ASPECT

Level operation

This sets the aspect ratio of the SD images. However, it is not valid if a setting other than GPI has been selected for the SD ASPECT item on the VIDEO CONFIG screen.

<Note>

This function is not valid when HD signals are supplied.

HD ZOOM

Level operation

This performs the HD ZOOM operations. (For details on

HD ZOOM, refer to page 5.)

<Notes>

This function is not valid when SD signals are supplied.

It is not valid when FRONT has been selected as the

HD ZOOM item setting on the SYSTEM CONFIG screen.

BACKLIGHT MIN.

This sets the backlight brightness to the minimum level.

Level operation

<Note>

The setting for the BACKLIGHT item can be changed on the SYSTEM CONFIG screen while BACKLIGHT MIN. is kept at ON. When BACKLIGHT MIN. is set to OFF and back to ON at this time, the brightness will be set to the minimum level.

R TALLY

Level operation

G TALLY

For lighting up the red tally lamp.

For lighting up the green tally lamp.

Level operation

MONO ON/OFF

Level operation

For setting the images to the monochrome mode.

However, this function is not valid when a setting other than GPI has been selected for the MONO item on the

VIDEO CONFIG screen.

GAMMA SELECT

This switches the gamma setting to FILM. (Refer to page

Level operation

18)

WFM ON/OFF

Level operation

This displays the Y signal (brightness) waveforms.

* Concerning the operation conditions

Level operation: The function is operational while the pin to which it has been allocated is shorted to ground.

Edge operation: The function is operational when the pin to which it has been allocated changes from open to shorted to ground.

<Note>

If a function whose operation condition is triggered by the level has been allocated to a multiple number of pins, it will continue to be operational while any one of those pins is shorted.

22

REMOTE specifications

RS-232C connector

For the RS-232C connector pin layout and connections, refer to the figure below and tables on the right.

<Note>

For details on systems that use the RS-232C connector, consult with your dealer a Panasonic Service Center.

RS-232C

5 4 3 2 1

9 8 7 6

7

8

9

4

5

6

Pin no.

1

2

3

PC side

Signal

NC

TXD

RXD

NC

GND

DSR

RTS

CTS

NC

BT-LH900P side

Pin no.

Signal

4

5

6

1

2

3

7

8

9

RTS

CTS

NC

NC

TXD

RXD

NC

GND

DSR

Error and warning displays

If an error has occurred in the monitor for some reason, an error or warning display will appear on the screen.

±

CRCC error

When this error appears

When the SDI signals contain an error, the CRCC error display appears on the screen.

When a menu is displayed, the error is indicated in the menu area. At all other times, it is indicated on the status display. However, only the error will be displayed when 3SEC OFF or OFF has been selected as the STATUS

DISPLAY item setting on the OSD screen. On the other hand, if OFF has been selected as the CRCC MESSAGE item setting on the OSD screen, the error will not be displayed even when it has been detected.

Countermeasure

Check the input signals and connection statuses.

±

Inverter error

When this error appears

If trouble has occurred in the inverter which controls the brightness of the backlight, the backlight is turned off, and all the lamps by the sides of the image controls and tally lamps flash at 1-second intervals.

Countermeasure

Turn off the power and turn it back on. If the error display persists, contact a Panasonic service center.

±

Low remaining battery charge warning/error

When this warning/error appears

If the battery voltage is 10.5V to 11.3V:

(If the remaining charge is less than 10% when an Anton Bauer digital battery is being used)

> The remaining battery charge and voltage are displayed on the screen, and the display flashes.

If the battery voltage is less than 10.5V:

> “END BATTERY” appears on screen in red for about three seconds, and the power is turned off.

Countermeasure

Replace the battery with one containing a sufficient charge.

23

Maintenance

Wipe off any dust or dirt on the monitor and LCD panel with a soft cloth.

For stubborn dirt or stains, wipe the monitor and LCD panel with a cloth that has been lightly dampened with well-diluted kitchen detergent and wrung out thoroughly, then finish it off with a dry cloth. The monitor may malfunction if even one drop of water gets into the internals.

Do not use benzine, paint thinners, etc. to clean the monitor.

They may discolor the monitor's surfaces or cause the paint to peel off.

Do not spray detergent or other cleaners directly on the monitor or LCD panel.

The monitor may malfunction if even one drop of water gets into the internals.

Maintenance and inspections

In order to ensure that this video component will provide many hours of trouble-free operation, provide the appropriate maintenance and servicing at periodic intervals so that the monitor's functions will be kept in perfect working order at all times. In order to ensure that the monitor's functions will perform to the best of their ability for a long time to come, be absolutely sure to conduct the maintenance and inspections described here.

1. Necessity for periodic maintenance and servicing

A backlight power supply is used in this LCD monitor.

This part (which is a consumable) will deteriorate over time and lead to a reduced level of performance and failure.

For this reason, do not confine the maintenance activities to the kind of after-sale servicing which is performed when the usual failures have occurred. The user should know that it is important to follow through with comprehensive servicing which involves periodic maintenance and servicing aimed at keeping up the performance that the monitor is designed to provide and preventing sudden failures caused by consumable parts, etc.

2. Maintenance timeframe and implementation item

The maintenance implementation time given below is provided as a standard guideline, and it does not represent the service life of the part concerned. It should also be borne in mind that the period over which the part's performance will deteriorate differs according to the operating environment and method.

Part

Backlight

Quantity Periodic maintenance/inspection and time (hours)

1 Replace every 38,000 hours.

24

Specifications

[GENERAL]

Power supply: DC 12 V (11.0 V to 17.0 V)

Input current: 1.45 A

indicates safety information.

Dimensions (W a H a D):

218 a 176 a 65 mm

(When the main controls have been installed at the bottom of the monitor)

Weight:

2.0 kg (main unit only)

Ambient operating temperature:

0 °C to 40 °C

Ambient operating humidity:

10% to 85% (no condensation)

Ambient temperature for storage:

–4 °F to 140 °F (–20 °C to +60 °C)

[Panel]

Size:

8.4 type

Number of pixels:

1024 a 768 (XGA)

Display colors:

Approx. 16.77 million colors

Angle of view:

Top-bottom direction: 170°

Left-right direction: 170°

[Signal formats supported]

Formats when SDI signals are used

480/59.94I

720/60P

1035/60I

1080/24PsF

1080/24P

1080/25P

1080/29.97P

1080/60I

576/50I

720/59.94P

1035/59.94I

1080/23.98PsF

1080/23.98P

1080/30P

1080/50I

1080/59.94I

Formats when RGB signals are used

480/59.94I

576/50I

480/59.94P

720/59.94P

720/60P

1035/60I

1035/59.94I

1080/60I

1080/50I

1080/59.94I

Formats when Y/Pb/Pr signals are used

480/59.94I

576/50I

480/59.94P

720/59.94P

1035/59.94I

1080/23.98PsF

720/60P

1035/60I

1080/24PsF

1080/24P

1080/23.98P

1080/30P

1080/50I

1080/59.94I

1080/25P

1080/29.97P

1080/60I

Formats when video signals are used

480/59.94I

576/50I

[Accessories provided with the monitor]

Metal battery mount

[Input connectors]

Image input:

VIDEO:

1 line, BNC a 2

(1 connector with through-out configuration)

Analog component:

1 line for YPBPR/RGB, BNC a 4

SDI:

2 lines, BNC a 3

(1 connector with switched out facility)

GPI:

D-sub, 9 pins

RS-232C:

D-sub, 9 pins

DC input:

XLR, 4 pins

Battery holder:

Battery holder made by Anton Bauer

25

MEMO

26

MEMO

27

PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY

UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA

Executive Office:

One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000

EASTERN ZONE:

One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621

Southeast Region:

1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835

Central Region:

1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200

WESTERN ZONE:

3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500

Government Marketing Department:

52 West Gude Drive, Rockville, MD 20850 (301) 738-3840

Broadcast PARTS INFORMATION & ORDERING:

9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880

Emergency after hour parts orders (800) 334-4881

TECHNICAL SUPPORT:

Emergency 24 Hour Service (800) 222-0741

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010

Panasonic de Mexico S.A. de C.V.

Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127

Panasonic Sales Company

Division of Matsushita Electric of Puerto Rico Inc.

San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300

advertisement

Related manuals