advertisement
REMOTE specifications
This monitor can be operated by remote control using the GPI connector and
RS-232C connector.
GPI connector
The items on the GPI screen correspond to the connector pins shown below.
Functions can be allocated to these pins on the GPI screen of the main menu. (Refer to page 19)
The functions allocated to the pins are enabled when the corresponding pin is shorted (ON) to the GND pin and disabled when it is left open (OFF).
5 4 3 2 1
9 8 7 6
Connector (9P)
Pin no.
1
4
5
2
3
8
9
6
7
Signal
GPI1
GPI2
GPI3
GPI4
GND
GPI5
GPI6
GPI7
GPI8
List of functions allocated
The function which can be allocated to the pins are listed below.
Function
Description
Operation condition
UNDEF
Not set (no function allocated)
MARKER1 ON/OFF This displays the markers which have been set by the
Level operation
GPI PRESET1 item on the MARKER screen. (Refer to page 16) However, it is not valid when MENU has been selected as the MARKER SELECT item setting on the
MARKER screen.
<Note>
When this function has been set to ON at the same time as MARKER2, MARKER1 takes precedence.
MARKER2 ON/OFF This displays the markers which have been set by the GPI
Level operation
PRESET2 item on the MARKER screen. (Refer to page
16) However, it is not valid when MENU has been selected as the MARKER SELECT item setting on the
MARKER screen.
MARKER BACK
HALF
Level operation
This sets the background brightness to 50% when 4:3,
13:9 or 14:9 has been selected for the GPI PRESET1 item setting on the MARKER screen. However, it is not valid when MENU has been selected as the MARKER
SELECT item setting on the MARKER screen.
MARKER BACK
BLACK
Level operation
This sets the background brightness to 0% when 4:3,
13:9 or 14:9 has been selected for the GPI PRESET1 item setting on the MARKER screen. However, it is not valid when MENU has been selected as the MARKER
SELECT item setting on the MARKER screen.
<Note>
When this function has been set to ON at the same time as MARKER BACK HALF, MARKER BACK BLACK takes precedence.
CENTER MARKER
This displays the center marker.
However, it is not valid when MENU has been selected
Level operation
as the MARKER SELECT item setting on the MARKER screen.
<Note>
When any other markers are displayed, the center marker is superimposed onto the same display.
Function
Description
Operation condition
INPUT SEL. SDI1
Edge operation
This switches the input channel to SDI 1.
<Note>
This function is not valid when OFF has been selected as the SDI 1 item (see page 20) setting on the FORMAT screen.
INPUT SEL. SDI2
Edge operation
This switches the input channel to SDI 2.
<Note>
This function is not valid when OFF has been selected as the SDI 2 item (see page 20) setting on the FORMAT screen.
INPUT SEL. VIDEO
This switches the input channel to VIDEO.
Edge operation
<Note>
This function is not valid when OFF has been selected as the VIDEO item (see page 20) setting on the FORMAT screen.
INPUT SEL.
YPBPR/RGB
Edge operation
This switches the input channel to ANALOG.
<Note>
This function is not valid when OFF has been selected as the YPBPR/RGB item (see page 20) setting on the
FORMAT screen.
SD ASPECT
Level operation
This sets the aspect ratio of the SD images. However, it is not valid if a setting other than GPI has been selected for the SD ASPECT item on the VIDEO CONFIG screen.
<Note>
This function is not valid when HD signals are supplied.
HD ZOOM
Level operation
This performs the HD ZOOM operations. (For details on
HD ZOOM, refer to page 5.)
<Notes>
≥
This function is not valid when SD signals are supplied.
≥
It is not valid when FRONT has been selected as the
HD ZOOM item setting on the SYSTEM CONFIG screen.
BACKLIGHT MIN.
This sets the backlight brightness to the minimum level.
Level operation
<Note>
The setting for the BACKLIGHT item can be changed on the SYSTEM CONFIG screen while BACKLIGHT MIN. is kept at ON. When BACKLIGHT MIN. is set to OFF and back to ON at this time, the brightness will be set to the minimum level.
R TALLY
Level operation
G TALLY
For lighting up the red tally lamp.
For lighting up the green tally lamp.
Level operation
MONO ON/OFF
Level operation
For setting the images to the monochrome mode.
However, this function is not valid when a setting other than GPI has been selected for the MONO item on the
VIDEO CONFIG screen.
GAMMA SELECT
This switches the gamma setting to FILM. (Refer to page
Level operation
18)
WFM ON/OFF
Level operation
This displays the Y signal (brightness) waveforms.
* Concerning the operation conditions
Level operation: The function is operational while the pin to which it has been allocated is shorted to ground.
Edge operation: The function is operational when the pin to which it has been allocated changes from open to shorted to ground.
<Note>
If a function whose operation condition is triggered by the level has been allocated to a multiple number of pins, it will continue to be operational while any one of those pins is shorted.
22
advertisement