Leviton EV48SDP Series Electric Vehicle AC Charger User Manual

Electric Vehicle AC Charger
EV48SDP Series (NA) - User
Manual
说明书
技术要求：
1.成品规格： 142 x 210 mm；
2.印刷方式：
单面印刷 ；
双面印刷；
3.装订方式：
骑马钉；
单面对折；
4.材质：
70g双胶纸；
108g铜板纸；
5.印刷颜色： 单黑色；
6.有条码的话，刷码等级需达到B级；
7.检验工具：卷尺，尺寸单位均为mm
线条图提供者
设计者
排版者
审核者
庄妍妍
EV48SDP Series (NA)
2024.09.19
批准者
文件翻译者
1:1
版本号
修订原因
修订人 修订日期
签名
日期
签名
Electric Vehicle AC Charger
EV48SDP Series (NA) - User Manual
Version 1
USER MANUAL
USER MANUAL
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ................................... 1
2. PRODUCT INTRODUCTION ..................................................... 5
3. INSTALLATION PREPARATION ............................................... 8
4. WALL MOUNTING................................................................... 10
5. WIRE THE CIRCUIT AND INSTALL........................................ 12
6. LIGHT CODES ......................................................................... 20
7. FCC DECLARATION ............................................................... 21
8. WARRANTY AND MAINTENANCE......................................... 22
USER MANUAL
USER MANUAL
1. Important Safety Instructions
1.2 Installation Requirements
1.1 Overall Warnings & Cautions
WARNING: Disconnect electrical power prior to installing the charging station.
Read and follow all warnings and instructions before installing and operating the product.
WARNING: Be sure to preview the user manual and ensure local building and electrical codes
WARNING: To avoid fire, injury or death, carefully read and follow the instructions during
are reviewed before installing the DC charger.
installation, operation and maintenance.
WARNING: The AC charger should be installed by a qualified technician according to the user
- DO NOT put fingers into the electric vehicle connector.
manual and local safety regulations.
- DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken,
CAUTION: Use appropriate protection when connecting to the main power distribution cable.
or any other signs of damage.
CAUTION: Type B, C or D breaker with the rating current for table should be installed in the
- DO NOT remove cover or attempt to open the enclosure because of risk of electric shock.
upstream AC distribution box.
- DO NOT install the product near flammable, explosive, or combustible materials.
CAUTION: The device shall be mounted at height between 2 feet and 4 feet from ground.
WARNING: The product should be supervised when used around children.
CAUTION: Please keep the charger in a clean area with low humidity. Not recommended to be
WARNING: The product must be grounded.
installed in coastal environments with high humidity or high dust.
WARNING: To avoid a risk of fire or electric shock, do not use this device with an extension
cord.
1.3 Daily Maintenance
WARNING: To reduce the risk of fire, connect only to a circuit provided branch circuit
over-current protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part
1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70
National Electrical Code (USA).
CAUTION: Avoid moisture or water in the charger. If there is water or moisture ingress in the
charger, it is necessary to immediately power off to avoid immediate danger, and notify the
professionals to carry out maintenance before next use.
CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If it is
damaged, please contact a professional technician.
Circuit Breaker Options table
Output Amperage (A)
1
CAUTION: Avoid placing the charger near hot objects and at high temperature locations and
32A*2
40A*2
48A*2
Circuit Breaker Options (A)
Method 1
40A*2
50A*2
60A*2
Circuit Breaker Options (A)
Method 2
80A
100A
120A
away from dangerous substances such as flammable gases and corrosive materials.
CAUTION: Do not put heavy objects on the charger to avoid danger.
2
USER MANUAL
USER MANUAL
1. Consignes De Sécurité Importantes
1.2 Exigence Avant L’installation
1.1 Avertissement & Mise En Garde Généraux
AVERTISSEMENT : Assurez-vous de consulter le manuel d'utilisation et assurez-vousque les
AVERTISSEMENT : Pour éviter les risques d’incendie, de blessure ou de mort, il faut lire et
codes locaux du bâtiment et de l'électricité sont passés en revue avant d'installer le chargeur.
suivre soigneusement les instructions pendant l’installation, l’utilisation et l’entretien.
- Ne mettez pas les doigts dans le connecteur du véhicule électrique.
- N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché,
isolé ou présentant tout autre signe de dommage.
AVERTISSEMENT : Débranchez l'alimentation électrique avant d'installer la station decharge.
AVERTISSEMENT : Le chargeur CA doit être installé par un technicien qualifié conformément au
manuel d'utilisation et aux réglementations de sécurité locales.
- N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou
MISE EN GARDE : Utilisez une protection appropriée lors de la connexion au câble de distribu-
montre toute autre indication de dommage.
tion d'alimentation principal.
Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier en raison du risque de choc
MISE EN GARDE : Un disjoncteur de type B, C ou D avec le courant nominal indiqué dans le
électrique.
tableau doit être installé dans le boîtier de distribution CA en amont.
AVERTISSEMENT : Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants.
AVERTISSEMENT : Cet appareil doit être mis à la terre.
AVERTISSEMENT : Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez pas
MISE EN GARDE : Cet appareil doit être monté à une hauteur entre 2 feet and 4 feet du sol.
MISE EN GARDE : Veuillez conserver le chargeur dans un endroit propre et peu humide. Il n’est
pas recommandé de l'installer dans des environnements côtiers à forte humidité ou à forte
cet appareil avec une rallonge électrique.
AVERTISSEMENT : L'adéquation de l'utilisation du cordon flexible conformément au code
poussière.
ce, partie i, règle 4-012, doit être déterminée par l'autorité d'inspection locale compétente.
1.3 Entretien Quotidien
AVERTISSEMENT : Pour réduire les risques d'incendie, ne connecter qu'à un circuit
protection contre les surintensités des circuits de dérivation conformément à la norme
canadienne CSA C22.1-15 Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installations électriqu (Mexique) ou ANSI / NFPA 70 National Electrical Code (États-Unis).
MISE EN GARDE : Évitez l'humidité ou l'eau dans le chargeur. En cas d'infiltration d'eau ou
d'humidité dans le chargeur, il est nécessaire de l'éteindre immédiatement pour éviter tout danger
immédiat et d'avertir le personnel professionnel d'effectuer l'entretien avant la prochaine utilisation.
MISE EN GARDE : Veuillez utiliser le chargeur correctement. Ne frappez pas ou n'appuyez pas
trop fort sur le boîtier. Si le boîtier est endommagé, veuillez contacter un technicien professionnel.
Circuit Breaker Options table
Output Amperage (A)
32A*2
40A*2
48A*2
Circuit Breaker Options (A)
Method 1
40A*2
50A*2
60A*2
Circuit Breaker Options (A)
Method 2
80A
100A
120A
MISE EN GARDE : Évitez de placer le chargeur à proximité d'objets chauds et à des endroits à
haute température et loin de substances dangereuses telles que des gaz inflammables et des
matériaux corrosifs.
MISE EN GARDE : Ne placez pas d'objets lourds sur le chargeur pour éviter tout danger.
3
4
USER MANUAL
USER MANUAL
2. Product Introduction
CAUTION: Avoid placing the charger near hot objects and at high temperature locations
and away from dangerous substances such as flammable gases and corrosive materials.
2.1 Basic Interface
2.2 Basic Dimensions
Enclosure
4.8"
12.2"
4G SIM Card Solt
Light Bar
78
78
90 1
23
90 1
23
RS485 Port
(connects the RS485 cables)
4.8"
19.2"
4 56
Card Swipe Area
RJ45 Port
(connects the RJ45 cables)
4 56
7" LCD
Touch Screen
Reset
CAN Port
(connects the CAN cables)
Current Selector
(adjusts the current for the charger)
Wall-Mounted Bracket
2.8"
4.8"
AC Power Cord Interface
(Bottom Connect)
Ethernet Inlet Hole
AC Power Cord Interface
(Rear Connect)
Dual Charging
Cable Interface
5
6
USER MANUAL
USER MANUAL
3. Installation Preparation
2.3 Technical specifications
3.1 Verify contents
EV48SDP
POWER
Input Rating
208~240V AC
Output Current
48A*2
Network Type
L1 / L2 / GND
Input Cord
50 / 60 Hz
Connector Type
SAE J1772 Type1 18ft / SAE J3400 NACS 18ft (Optional)
Protection
Meter Accuracy
CCID 20
±1% (CTEP qualified)
Status Indication
LED indication
Screen
7" touch screen
English / Spanish / French
User Interface
Compatible with multiple CPOs
Connectivity
Bluetooth5.2, Wi-Fi 6 (2.4G / 5G), Ethernet
Communication Protocols
Pile Group Management
User Authentication
Card Reader
Software Update
OTA
7
0:8A; 1:16A; 2:24A; 3:32A; 4:40A; 5:48A;
NEMA 4 (IP65), IK08
Cable Ramp ×1
ST3.5*16
Screws ×2
RFID Card ×2
Shorting Terminal
Combination (2pcs) ×1 Mounting template ×1 RNB Terminal ×6
AD21.2
Conduit Fitting ×1
AD42.5
Conduit Fitting ×1
M40
Conduit Fitting ×1
Holster Bracket
(Optional) ×2
Plug Holster
M5*16mm
Screws (Optional) ×2
Holster Bracket
Screws
(Optional) ×8
Plug Holster
(Optional) ×2
＜6561ft (2000m)
Operating Temperature
−40°F ~ +131°F (−40°C ~ +55°C)
Storage Temperature
−40°F ~ +185°F (−40°C ~ +85°C)
Product Dimensions
Allen Wrench ×1
UL991, UL1998, UL2231, UL2594, ISO15118 (PnC)
36 months
Mounting
M6 Hexagonal
Expansion Screws ×4
ISO 14443 A/B, ISO / IEC 15693,
VAS & Apple, Pay & Google, Pay & More (Optional)
GENERAL
Operating Humidity
M4 Anti-Theft
Screws ×2
Plug&Charge (Free) / RFID Card / Credit Card (Optional)
ETL / FCC / Energy Star
Operating Altitude
Wall-Mounted
Bracket ×1
ISO15118-2/3 (Optional)
Warranty
Enclosure Rating
User Manual ×1
Dynamic Load Balancing
Certification
Dip Switch
AC Charger ×1
OCPP2.0.1 / OCPP 1.6Js self-adaptation
CERTIFICATION & STANDARDS
Safety & Compliance
EV48SDP Series (NA) -User Manual
UVP, OVP, RCD (CCID 20), SPD, Ground Fault Protection,
OCP, OTP, Control Pilot Fault Protection
USER INTERFACE
Language
Electric Vehicle AC Charger
Hard-wire
Mains frequency
Ground Fault Detection
Check the box to ensure you have the user manual, and these parts:
5~95%
Wall mount / Pedestal (optional)
12.2"×19.2"×4.8” (310×488×122mm)
8
USER MANUAL
USER MANUAL
4. Wall mounting
3.2 Gather Tools
In addition, you will need the following tools and accessories:
WARNING: This device must be grounded. Disconnect electrical power prior to
1. Level
installing the charging station.
2. Drill
3. Gummi hammer
STEP 1
4. Phillips screwdriver
5. Wire stripper
Make sure the installation wall is vertical, and use the Mounting template to drill four screw holes
6. Voltmeter or digital multi-meter
with a diameter of 0.33" (8.5mm) and a depth of 2.17"~2.36" (55mm~60mm) at a height of
(for measuring AC voltage at the installation site)
47.24"~51.18" (1200-1300mm) from the ground according to the hole positions.
Please drill screw holes in the direction of the template arrow.
Use Gummi hammer to fix the expansion screws into the holes.
1
9
5
3
6
47.24"~51.18" (1200-1300mm)
4
2
UP
Wall mounting use the mounting layout
template provided to drill the holes
1.Tape the layout template on the wall to the position
where you plan to install the charger.
2.Mark the mounting holes （which are marked as circles
on the template ) on to the wall.
3.Remove the template.
4.Drill the 4 mounting holes of size
φ10 and a depth of 50~55mm.
WARNING: If you hit something metallic when drilling,
stop immediately and contact an electrician.
Ground
10
USER MANUAL
USER MANUAL
STEP 2
1. Remove the 2 M4 Anti-theft screws from backplate by allen wrench.
3. Align the rear notch of charger with the wall-mounted bracket and alignment the screw holes at
the bottom, and secure it using M4 Anti-Theft Screws.
2. Use 4 Hexagonal Expansion Screws to secure the wall-mounted bracket on the wall, Use an
wrench to tighten the screw nuts on the expansion screws.
5. Wire The Circuit
STEP 1
Use a allen wrench to loosen the two
screws located at the bottom of the
charging station. Open the buckle on both
sides and lift up the front cover to remove
it from the charging station.
11
12
USER MANUAL
USER MANUAL
STEP 2
STEP 4
Remove the cover from the charger using
We support two methods of AC Power input, the two methods of wiring will be different,
the appropriate tools. (such as coin)
respectively, as follows:
Method 1: Two AC Power Cord and two Charging Cable
Method 2: One AC Power Cord and two Charging Cable
(Using shorting terminals to connect AC1_L1 and AC2_L1, connect AC1_L2 and AC2_L2)
COCN
STEP 3
L1 L2 GND
L1
L2
GND
L1
L2
L1 L2 GND
L1 L2 GND
L1
L2
GND
L1
L2
L1 L2 GND
Remove the waterproof plug from the charger
cable inlet，Connect and Lock the M40 Conduit
Fitting Part1 ( 1 ) and Part2 ( 2 ) (including the
washer) to the Inlet as shown below.
Method 1
Note:
Method 1: Two AC Power Cord
1.You need to bring your own AC input cable.
2.Select the AD42.5 or M40 Conduit Fitting
Circuit Breaker Options table
based on the AC input cable type
If you choose One AC Power Cord，you can
use M40 or AD42.5 Conduit Fitting
If you choose Two AC Power Cord，you only
use AD42.5 Conduit Fitting
3.If you use AD42.5 Conduit Fitting，perform the
same steps as above，and you need to bring
Method 2
1
L1 L2 GND
Output Amperage (A)
32A*2
40A*2
48A*2
Circuit Breaker Options (A)
40A*2
50A*2
60A*2
L1 L2 GND
1
STEP 4-1
2
3
Press the wires of AC power cord onto the RNB
2
terminals in the accessory kit.
L1
L2
GND GND
L1
L2
your own bellows.
13
14
USER MANUAL
USER MANUAL
STEP 4-2
STEP 4-2
First, pass the two AC power cords through the M40 Conduit Fitting Part 3 ( 3 ), then continue
Take out the shorting terminals in the accessory package. Connect AC1_L1 and AC2_L1, and
through Part 1 and Part 2. Connect the five terminals according to the following wiring methods
connect AC1_L2 and AC2_L2 according to thefollowing wiring methods image.
image, and connect the two GND together.
L1
L1
L2
GND
L1
L2
GND
L1
L2
L2
L1 L2 GND
L1
L2
GND
L1
L2
L1 L2 GND
L1 L2 GND
L1
L2
GND
L1
L2
L1 L2 GND
3
Method 2: One AC Power Cord
STEP 4-3
Circuit Breaker Options table
First, pass the One AC power cords through the M40 Conduit Fitting Part 3 ( 3 ), then continue
Output Amperage (A)
32A*2
40A*2
48A*2
Circuit Breaker Options (A)
80A
100A
120A
through Part 1 and Part 2. Connect the three terminals according to the following wiring methods
L1 is connected to L1, L2 is connected to L2, and GND is connected to GND.
STEP 4-1
L1
Press the wires of AC power cord onto the RNB terminals in the accessory kit.
L1 L2 GND
L1
L2
L1
L2
GND
L1
L2
L2
GND
L1
L2
L1 L2 GND
GND
3
15
16
USER MANUAL
USER MANUAL
STEP 5
STEP 7
Lock the M40 Conduit Fitting Part 3 ( 3 ), Press the AC input cable with cable ramp and secure it
This AC charger is equipped with two current selectors, each corresponding to the left and right
with two screws (3.5*16).
connectors, enabling it to support different maximum output currents via the setting rotary switch.
Setting methods are shown below：
Before setting the rotary switch, make sure the input power is turned OFF.
Use a non-conductive object to set the rotary switch.
L1 L2 GND
L1
L2
GND
L1
L2
L1 L2 GND
78
23
901
3
STEP 6
78
78
4 56
4 56
L2
23
90 1
23
L1
456
90 1
L1 L2 GND
GND
L1
L2
L1 L2 GND
Remove the waterproof plug from the charger cable inlet. Connect and lock the AD21.2 conduit
fitting Part1 ( 1 ) and Part2 ( 2 ) to the inlet. Then, insert the Ethernet cable with the RJ45 plug into
the bellows, through the AD21.2 conduit fitting, and plug the cable into the RJ45 port
(RS232/RS485 operate in the same mode).
Note: You need to bring your own bellows.
78
78
2
3
4
5-9
Maximum Output Current
8A
16A
24A
32A
40A
48A
4 56
4 56
L2
1
23
1
L1
0
90 1
23
90 1
L1 L2 GND
Switch Setting Number
GND
L1
L2
L1 L2 GND
1
2
2
17
18
USER MANUAL
USER MANUAL
6. Light Codes
STEP 8
6.1 After Start UP
Align the cover with its position on the
charging station.Secure the cover in place
using the appropriate tools (such as coin).
COCN
STEP 9
Align the magnetic positions of the cover
plate and the middle frame, Fasten both
clips and fix the two screws at the bottom.
19
Device Status
Light Codes
Power On
Blue, green and red run clockwise
Standby
Solid Blue
Plug The Charging Connector
Solid Green
Authentication（Swipe Card）
Green Blinking
Charging In Progress
Green Breathing
Finished / Stopped Charging
Solid Green
Reservation Charging
Solid Yellow
Device Unabailable
Yellow Blinking
OTA
Yellow Breathing
Fault
Red
6.2 Error and Warning Messages
No.
Fault Status
Red Light
Remark
1
Meter Fault
1 flash followed by 3 sec pause
Auto Recover
2
CP Fault
2 flashes followed by 3 sec pause
Unplug the Connector to Recover
3
UVP
3 flashes followed by 3 sec pause
Auto Recover
4
OVP
4 flashes followed by 3 sec pause
Auto Recover
5
OTP
5 flashes followed by 3 sec pause
Auto Recover
6
OCP
6 flashes followed by 3 sec pause
Unplug the Connector to Recover
7
Ground Fault
7 flashes followed by 3 sec pause
Unplug the Connector to Recover
8
Relay Fault
8 flashes followed by 3 sec pause
Unplug the Connector to Recover
9
RCD Abnormal
9 flashes followed by 3 sec pause
Unplug the Connector to Recover
10
RCD Self-Test Fault 10 flashes followed by 3 sec pause
Reboot to Recover
11
Relay Self-Test Fault 11 flashes followed by 3 sec pause
Reboot to Recover
12
Sensor Fault
12 flashes followed by 3 sec pause Check sensor or contact after-sales
13
Cable Fault
13 flashes followed by 3 sec pause
Check cable or contact after-sales
20
USER MANUAL
USER MANUAL
7. FCC Declaration
8. Warranty and Maintenance
This device complies with part 15 of the FCC Rules.
• The warranty period for this charger is three years.
• During the warranty period for any malfunction under normal use according to the User Manual
Operation is subject to the following two conditions:
(to be determined by certified maintenance technicians of sellers), the product shall be repaired
This device may not cause harmful interference, and this device must accept any interference
free of charge. Except for the following situations, the charger shall be subject to the above
received, including interference that may cause undesired operation.
warranty terms:
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
Caution: Changes or modifications to this unit not expressly approved by the party responsible
modified
for compliance could void the user's authority to operate the equipment.
or inconsistent with the label indication of the repaired product.
2. Those who are unable to provide valid proof of purchase.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
3. Those who exceed the manufacturer's specified warranty period.
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
4. Those who damage the product due to not following the product service instruction for use,
protection against harmful interference when the equipment is operated in a commercial
maintenance and storage.
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
5. Damage or malfunction caused by external object entering.
installed and used in accordance with the instruction manual, may cause harmful interference to
6. Unauthorized repair, disassembly or modification.
radio communications. Operation of this equipment in a residential area is likely to cause harmful
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire, flood,
interference in which case the user will be required to correct the interference at his own expense.
etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
WIFI module: Containing FCC ID: XMR2023FCS960K
damage caused by improper use of equipment, such as water or other solutions entering into the
equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not specified for
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should
use with the charger equipment.
be maintained between the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance is not recommended.
The above guarantees shall be made solely, and no other express or implied warranties shall be
made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
Company shall not be responsible for any special, incidental or consequential damages.
21
22
">