LEDVANCE EVC Electric Vehicle AC Charger User Manual

Electric Vehicle AC Charger
EVC/48A/LVL2/4G/C2/YY - User Manual
说明书
技术要求：
1.成品规格： 142 x 210 mm；
2.印刷方式：
单面印刷 ；
双面印刷；
3.装订方式：
骑马钉；
单面对折；
4.材质：
70g双胶纸；
108g铜板纸；
5.印刷颜色： 单黑色；
6.有条码的话，刷码等级需达到B级；
7.检验工具：卷尺，尺寸单位均为mm
线条图提供者
设计者
排版者
审核者
庄妍妍
EVM002 Series (NA)
2024.07.12
批准者
文件翻译者
1:1
版本号
修订原因
修订人 修订日期
签名
日期
签名
Electric Vehicle AC Charger
EVC/48A/LVL2/4G/C2/YY - User Manual
Version 1
USER MANUAL
USER MANUAL
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ................................... 1
2. PRODUCT INTRODUCTIONS................................................... 5
3. VERIFY CONTENTS.................................................................. 8
4. GATHER TOOLS ....................................................................... 9
5. PLAN THE MOUNTING ........................................................... 10
6. WALL MOUNTING................................................................... 11
7. WIRE THE CIRCUIT AND INSTALL 4G CARD....................... 14
8. LIGHT CODES ......................................................................... 18
9. FCC DECLARATION ............................................................... 20
10. WARRANTY AND MAINTENANCE....................................... 21
USER MANUAL
USER MANUAL
WARNING & CAUTION
WARNING & CAUTION
1. Important Safety Instructions
1.2 Installation Requirements
1.1 Overall Warnings & Cautions
WARNING: Disconnect electrical power prior to installing the charging station.
WARNING: To avoid fire, injury or death, carefully read and follow the instructions during
WARNING: Be sure to preview the user manual and ensure local building and electrical codes
installation, operation and maintenance.
are reviewed before installing the AC charger.
- DO NOT put fingers into the electric vehicle connector.
WARNING: The AC charger should be installed by a qualified technician according to the user
- DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken,
manual and local safety regulations.
or any other signs of damage.
CAUTION: Use appropriate protection when connecting to the main power distribution cable.
- DO NOT use this product if the enclosure or the EV connector is broken, cracked, open, or
CAUTION: Type B, C or D breaker with the rating current for table should be installed in the
shows any other indication of damage.
upstream AC distribution box.
- DO NOT remove cover or attempt to open the enclosure because of risk of electric shock.
CAUTION: The device shall be mounted at height between 2 feet and 4 feet from ground.
WARNING: This device should be supervised when used around children.
CAUTION: Please keep the charger in a clean area with low humidity. Not recommended to
WARNING: This device must be grounded.
be installed in coastal environments with high humidity or high dust.
WARNING: To avoid a risk of fire or electric shock, do not use this device with an extension
1.3 Daily Maintenance
cord.
CAUTION: Avoid moisture or water in the charger. If there is water or moisture ingress in the
WARNING: The suitability of the use of flexible cord in accordance with CE code, part I, rule
charger, it is necessary to immediately power off to avoid immediate danger, and notify the
4-012, is to be determined by the local inspection authority.
professionals to carry out maintenance before next use.
WARNING: To reduce the risk of fire, connect only to a circuit provided branch circuit
CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If it is
over-current protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part
damaged, please contact a professional technician.
1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70
CAUTION: Avoid placing the charger near hot objects and at high temperature locations and
National Electrical Code (USA).
away from dangerous substances such as flammable gases and corrosive materials.
CAUTION: Do not put heavy objects on the charger to avoid danger.
Circuit Breaker Options table
1
Output Amperage (A)
16A
32A
40A
48A
70A
80A
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
2
USER MANUAL
USER MANUAL
WARNING & CAUTION
WARNING & CAUTION
Consignes De Sécurité Importantes
1.2 Exigence Avant L’installation
1.1 Avertissement & Mise En Garde Généraux
AVERTISSEMENT : Assurez-vous de consulter le manuel d'utilisation et assurez-vousque les
AVERTISSEMENT : Pour éviter les risques d’incendie, de blessure ou de mort, il faut lire et
codes locaux du bâtiment et de l'électricité sont passés en revue avant d'installer le chargeur.
suivre soigneusement les instructions pendant l’installation, l’utilisation et l’entretien.
AVERTISSEMENT : Débranchez l'alimentation électrique avant d'installer la station decharge.
- Ne mettez pas les doigts dans le connecteur du véhicule électrique.
AVERTISSEMENT : Le chargeur CA doit être installé par un technicien qualifié conformément au
- N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché,
manuel d'utilisation et aux réglementations de sécurité locales.
isolé ou présentant tout autre signe de dommage.
MISE EN GARDE : Utilisez une protection appropriée lors de la connexion au câble de distribu-
- N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou
tion d'alimentation principal.
montre toute autre indication de dommage.
MISE EN GARDE : Un disjoncteur de type B, C ou D avec le courant nominal indiqué dans le
Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier en raison du risque de choc
électrique.
tableau doit être installé dans le boîtier de distribution CA en amont.
MISE EN GARDE : Cet appareil doit être monté à une hauteur entre 2 feet and 4 feet du sol.
AVERTISSEMENT : Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants.
AVERTISSEMENT : Cet appareil doit être mis à la terre.
AVERTISSEMENT : Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez pas
cet appareil avec une rallonge électrique.
AVERTISSEMENT : L'adéquation de l'utilisation du cordon flexible conformément au code
ce, partie i, règle 4-012, doit être déterminée par l'autorité d'inspection locale compétente.
MISE EN GARDE : Veuillez conserver le chargeur dans un endroit propre et peu humide. Il n’est
pas recommandé de l'installer dans des environnements côtiers à forte humidité ou à forte
poussière.
1.3 Entretien Quotidien
MISE EN GARDE : Évitez l'humidité ou l'eau dans le chargeur. En cas d'infiltration d'eau ou
d'humidité dans le chargeur, il est nécessaire de l'éteindre immédiatement pour éviter tout danger
AVERTISSEMENT : Pour réduire les risques d'incendie, ne connecter qu'à un circuit
immédiat et d'avertir le personnel professionnel d'effectuer l'entretien avant la prochaine utilisation.
protection contre les surintensités des circuits de dérivation conformément à la norme
canadienne CSA C22.1-15 Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installa-
MISE EN GARDE : Veuillez utiliser le chargeur correctement. Ne frappez pas ou n'appuyez pas
trop fort sur le boîtier. Si le boîtier est endommagé, veuillez contacter un technicien professionnel.
tions électriqu (Mexique) ou ANSI / NFPA 70 National Electrical Code (États-Unis).
MISE EN GARDE : Évitez de placer le chargeur à proximité d'objets chauds et à des endroits à
Circuit Breaker Options table
3
haute température et loin de substances dangereuses telles que des gaz inflammables et des
Output Amperage (A)
16A
32A
40A
48A
70A
80A
matériaux corrosifs.
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
MISE EN GARDE : Ne placez pas d'objets lourds sur le chargeur pour éviter tout danger.
4
USER MANUAL
USER MANUAL
2. Product Introductions
2.2 Basic Dimensions
CAUTION: Avoid placing the charger near hot objects and at high temperature locations
and away from dangerous substances such as flammable gases and corrosive materials.
9.61"
4.64"
2.1 Basic Interface
LED Light
Indication
Emergency
Button
15.83"
RFID
Swipe Area
SAE J1772
AC Charging
Connector
Rear Notch
Charging
Cable Inlet
2.83"
Rear AC Power Inlet
4.8"
AC Power Inlet
LAN
Cable Inlet
5
6
USER MANUAL
USER MANUAL
3. Verify Contents
2.3 Specifications
EVC/48A/LVL2/4G/C2/YY
Ensure you have this installation guide and these parts:
POWER
208~240V AC
Input Rating
Output Current&Power
Power Wiring
19.2 kW (80A)
11.5 kW (48A)
Input Cord
Hard-wire
Mains frequency
50 / 60 Hz
Connector Type
SAE J1772 Type1 18ft / SAE J3400 NACS 18ft (Optional)
Ground Fault Detection
Protection
Meter Accuracy
Electric Vehicle AC Charger
EVM002 Series (NA) -User Manual
L1 / L2 / GND
CCID 20
UVP, OVP, RCD (CCID 20), SPD, Ground Fault Protection,
OCP, OTP, Control Pilot Fault Protection
±1% (CTEP qualified)
AC Charger ×1
User Manual ×1
Wall-Mounted Bracket ×1
M4 Anti-Theft Round
Head Screws ×1
M6 Hexagonal Expansion
Screws ×4
Allen Wrench ×1
Mounting Template ×1
RFID Card ×2
Cable Ramp ×1
ST3.5*16 Screws ×2
AD34.5
Conduit Fitting ×1
AD21.2
Conduit Fitting ×1
USER INTERFACE
Status Indication
Screen
Language
LED indication
4.3' touch screen (UI upgradable)
English / Spanish / French
User Interface
Compatible with multiple CPOs
Connectivity
Bluetooth5.2, Wi-Fi (2.4G / 5G), Ethernet, 4G (optional)
Communication Protocols
User Authentication
Card Reader
Software Update
ISO15118-2/3
Dynamic Load Balancing
Plug&Charge(Free)、Plug&Charge(PnC)、RFID Card、OCPP
RFID, ISO14443A、ISO14443B, 13.56MHz
OTA
CERTIFICATION & STANDARDS
Safety & Compliance
Holster Bracket
Pile Group Management
OCPP2.0.1 / OCPP 1.6Js self-adaptation
UL991, UL1998, UL2231, UL2594, ISO15118 (P&C)
Certification
ETL / FCC / Energy Star
Warranty
36 months
GENERAL
Button
Emergency Button
Enclosure Rating
NEMA 4 (IP65), IK08
Operating Altitude
＜6561ft (2000m)
Operating Temperature
-40°F ~ +131°F (-40°C ~ +55°C)
Storage Temperature
-40°F ~ +185°F (-40°C ~ +85°C)
Operating Humidity
Mounting
Product Dimensions
7
5 ~ 95%
Wall mount / Pedestal (optional)
15.83"×9.61"×4.64" (402×244×118mm)
M32 Conduit Fitting ×1
8
USER MANUAL
USER MANUAL
5. Plan The Mounting
4. Gather Tools
Tools required before installing the Wall-Mounted charger, gather the following tools:
1. Wire stripper
WARNING: In areas with frequent thunderstorms, add surge protection at the service
panel for all circuits. Ensure all power and ground connections, especially those at the
2. Adjustable Wrench
breaker and bus bar, are clean and tight.
3. Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
4. Level
CAUTION: Not recommended to be installed in coastal environments with high
5. Pencil or marker
humidity or high dust.
6. Drill
7. Phillips screwdriver
Select the appropriate mounting location with electri calcapacity:
I. Ensure the owner has chosen a mounting location that allows the charging cable to reach the
car’s charging port while still providing slack.
1
4
2
5
3
6
II. The device must be anchored into mounting such as 3.14" x 5.11" stud or a solid wall.
7
Note: The above tools are very important, please gather them all.
9
10
USER MANUAL
USER MANUAL
6. Wall mounting
STEP 3
STEP 1
Use 4 Hexagonal Expansion Screws to secure the wall-mounted bracket on the wall, Use an
Make sure the installation wall is vertical, and use the Mounting template to drill four screw holes
wrench to tighten the screw nuts on the expansion screws.
with a diameter of 0.33" (8.5mm) and a depth of 2.17"~2.36" (55mm~60mm) at a height of
47.24"~51.18"(1200-1300mm) from the ground according to the hole positions.
Wall-Mounted Bracket
47.24"~51.18" (1200-1300mm)
Ground
STEP 2
Push the bracket down to remove the wall hanger.
STEP 4
Align the rear notch of charger with the wall-mounted bracket and alignment the screw holes at the
bottom, and secure it using M4 Anti-Theft Round Head Screws.
11
12
USER MANUAL
USER MANUAL
7. Wire The Circuit And Install 4G Card
STEP 5
Overall outlook picture after installation:
WARNING: This device must be grounded. Disconnect electrical power prior to
installing the charging station.
Wall-mounted cable winding
Plug holder (optional)
Pedestal (optional)
WARNING: Improper connection of the equipment-grounding conductor would result
in a risk of electric shock. Check with a qualified electrician or serviceman if you are
not sure whether the product is properly grounded. Do not modify the plug provided
with the product – if it doesn’t fit the outlet, have a proper outlet installed by a qualified
electrician.
CAUTION: Use appropriate protection when connecting to the main power distribution
cable.
This step is only to Hard-wire wiring and requires user-supplied AC input cables.
For safe use of electricity, please set circuit
breaker protection in the input part of EV Charger.
Circuit Breaker Options table
13
Output Amperage (A)
16A
32A
40A
48A
70A
80A
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
14
USER MANUAL
USER MANUAL
STEP 1
STEP 4
Use a allen wrench to loosen the two screws
Take out the AC input cable and strip the TPU
located at the bottom of the charging station.
cover by 5.52" (140mm), and then strip individual
Open the buckle on both sides and lift up the
wires by 0.47" (12mm). use ferrules on stranded
front cover to remove it from the charging
wires and press it by wire crimper.
station.
Note: You need to bring your own ferrules.
(ferrules)
0.47"(12mm)
5.52"(140mm)
STEP 2
Remove the cover from the charger using
the appropriate tools. (such as coin)
STEP 5
COCN
First, pass the AC input cable through the M32
STEP 3
Conduit Fitting Part 3 ( 3 ), then continue through Part
Remove the waterproof plug from the charger
1 and Part 2. Connect the wires (L1, L2, GND) and
cable inlet，Connect and Lock the M32 Conduit
tighten each connector screw to 2 N.m (17.7 in.lbs).
L1 L2 GND
Fitting Part1 ( 1 ) and Part2 ( 2 ) (including the
L1 L2 GND
washer) to the Inlet as shown below.
Note:
L1 L2 GND
1.You need to bring your own AC input cable.
2.Select the AD34.5 or M32 Conduit Fitting based
1
L1 L2 GND
3
1
2
on the AC input cable type，If you use AD34.5
Conduit Fitting, perform the same steps as above.
15
3
2
16
USER MANUAL
USER MANUAL
STEP 8
Align the cover with its position on the
STEP 6
charging station.Secure the cover in place
using the appropriate tools (such as coin).
Lock the M32 Conduit Fitting Part 3 ( 3 ),
Press the AC input cable with cable ramp and
STEP 9
secure it with two screws (3.5*16).
COCN
Insert the SIM (MICRO SIM) card according
L1 L2 GND
L1 L2 GND
to the picture’s instruction (for 4G version,
Optational).
3
STEP 10
Align the magnetic positions of the cover
plate and the middle frame, Fasten both
clips and fix the two screws at the bottom.
STEP 7
8. Light Codes
Remove the waterproof plug from the
charger cable inlet. Connect and lock the
8.1 After Start UP
AD21.2 conduit fitting Part1 ( 1 ) and Part2
( 2 ) to the inlet. Then, insert the Ethernet
cable with the RJ45 plug into the bellows,
L1 L2 GND
1
through the AD21.2 conduit fitting, and plug
L1 L2 GND
1
2
the cable into the RJ45 port (RS232/RS485
operate in the same mode).
Note: You need to bring your own bellows
17
2
Device Status
Light Codes
Power On
Blue, green and red run clockwise
Standby
Solid Blue
Plug The Charging Connector
Solid Green
Swipe Card
Green Blinking
Charging In Progress
Green Breathing
Finished / Stopped Charging
Solid Green
OTA
Yellow Breathing
Fault
Red
18
USER MANUAL
USER MANUAL
9. FCC Declaration
8.2 Error and Warning Messages
This device complies with part 15 of the FCC Rules.
No.
Fault Status
Red Light
Remark
1
Emergency Fault
Solid Red
Reset Recover
2
Meter Fault
1 flash followed by 3 sec pause
Auto Recover
3
CP Fault
2 flashes followed by 3 sec pause
Unplug the Connector to Recover
4
UVP
3 flashes followed by 3 sec pause
Auto Recover
5
OVP
4 flashes followed by 3 sec pause
Auto Recover
6
OTP
5 flashes followed by 3 sec pause
Auto Recover
7
OCP
6 flashes followed by 3 sec pause
Unplug the Connector to Recover
Note: This equipment has been tested and found to comply with the limits for a Class A digital
8
Ground Fault
7 flashes followed by 3 sec pause
Unplug the Connector to Recover
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
9
Relay Fault
8 flashes followed by 3 sec pause
Unplug the Connector to Recover
protection against harmful interference when the equipment is operated in a commercial
10
RCD Abnormal
9 flashes followed by 3 sec pause
Unplug the Connector to Recover
11
RCD Self-Test Fault
10 flashes followed by 3 sec pause
Reboot to Recover
12
Relay Self-Test Fault 11 flashes followed by 3 sec pause
Reboot to Recover
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference
received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
WIFI module: Containing FCC ID: XMR2023FCS960K
LTE module: Containing FCC ID: XMR202008EC25AFXD
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should
be maintained between the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance is not recommended.
19
20
USER MANUAL
10. Warranty and Maintenance
• The warranty period for this charger is three years.
• During the warranty period for any malfunction under normal use according to the User Manual
(to be determined by certified maintenance technicians of sellers), the product shall be repaired
free of charge. Except for the following situations, the charger shall be subject to the above
warranty terms:
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
modified
or inconsistent with the label indication of the repaired product.
2. Those who are unable to provide valid proof of purchase.
3. Those who exceed the manufacturer's specified warranty period.
4. Those who damage the product due to not following the product service instruction for use,
maintenance and storage.
5. Damage or malfunction caused by external object entering.
6. Unauthorized repair, disassembly or modification.
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire, flood,
etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
damage caused by improper use of equipment, such as water or other solutions entering into the
equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not specified for
use with the charger equipment.
The above guarantees shall be made solely, and no other express or implied warranties shall be
made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
Company shall not be responsible for any special, incidental or consequential damages.
21
">