Water2buy Water softener User manual

3001-R15.9.1
[2]
Safety & Care Advice
This water softener’s control valve conforms to the highest industry standards for materials and structural integrity.
Water2buy™ products are for use with microbiologically safe water.
Read and follow all safety rules and operating instructions before first use of this product. If you have questions
when installing, operating or maintaining your water softener, log on to www.water2buy.com and watch the user
installation video for your product. The approximate time required to install this unit is 3 hours.
Your water softener is heavy take precaution to prevent injury.
Do not exceed 6.89bar (100psi) water pressure.
Do not exceed 40C (104F) water temperature.
Do not subject unit to freezing conditions
Subjecting your unit to these conditions will void the warranty.
Read all steps, guides and rules carefully before installing and using your water softener. Follow all steps exactly
to correctly install. Reading this manual will help you get all the benefits from your water softener. We recommend
that a trained professional install this water softener.
Please follow all local codes for plumbing this unit. Follow local electrical codes. Install a correctly sized electrical
bonding jumper between the inlet and outlet pipes when these devices are installed in metallic plumbing systems.
Inspect this unit carefully for carrier shortage or shipping damage before beginning installation of unit.
This system should not be used for treating water that is microbiologically unsafe or of unknown quality. The unit is
designed with the sole purpose of removing hardness.
Use only lead-free solder and flux, as required local codes, when installing soldered copper plumbing. Use caution
when ‘sweat joining’ metal pipes near this water conditioning system. Heat can adversely affect the plastic used in
this system and bypass valve. Use only silicone grease for lubrication of this unit.
Do not allow this water softener to freeze. Damage from freezing will void this water softener’s warranty. Do not
store flammable or volatile chemicals near this water softener.
For the purpose of plumbing system sizing, only the rated service (i.e."Normal") flow and corresponding pressure
loss may be used. The rated service flow rates are the flow rates.
Use at least 3 metres of tubing between the outlet of the water softener and the inlet to the water heater. Water
heaters can overheat to the extent that they can send heat back down the cold pipe into the unit control valve.
Hot water can severely damage the softener. A 3-metre total pipe run, including bends, elbows, and fittings, is a
reasonable distance to help hot water damage. A positive way to prevent hot water from flowing from heat source
to the water softener, in the event of a negative pressure situation, is to install a check valve in the soft water
tubing from the softener. If a check valve is installed, make sure the water-heating unit is equipped with a rated
temperature and pressure safety relief valve. Be sure that local codes are not violated.
Do not locate unit where it or its connections (including the drain and overflow lines) will ever be subjected
o
o
o
o
temperatures less than 1 C (34 F) or greater than 40 C (104 F).
Do not install unit near acid or acid fumes. The use of resin cleaners in an un-vented enclosure is not
recommended
Drain line – Important: If the unit is located more than 6 metres from drain, use 22mm tubing for distances 612metres. Purchase appropriate fitting to connect the 22mm tubing to the 15mm drain connection (v) on the
control valve.
If the unit is located where the drain line must be elevated. You may elevate the line up to 1.8 metres providing the
tubing length does not exceed 4.5 metres and water pressure at softener is not less than 1.bar (14 psi). You may
elevate an additional 60cm for each additional .7bar of water pressure.
Where the drain line is elevated but empties into a drain below the level of the control valve, form a 20cm loop at
the end of the tubing so that the bottom of the loop is level with the drain line connection. This will provide an
adequate siphon trap.
Where the drain empties into an overhead sewer line, a sink trap must be used.
[3]
Installing your water softener unit
Check parts included: unpack the box and remove the water softener unit. The unit includes the parts listed below:
• Water softener
• Cover
• Power supply transformer
• Packet of Silicon lube
• In/Out plumbing connections
• Install guide
• Bypass valve adjustment tool (meter models only)
• Plumbing fittings
Tools and Materials needed
•
•
•
•
•
Adjustable wrench
Standard pliers, and larger adjustable jaw pliers or pipe wrench to fit sink drain slotted
Phillips head screwdrivers
Pipe joint compound (thread seal) or Teflon tape, approved for use on potable water supplies
Hand or battery powered drill
Log on to
www.water2buy.com
and watch the user
installation video
Attention: Get the latest manual
We recommend that you download the latest manual in PDF for this product
from www.water2buy.com as we frequently make updates to the
recommended instructions and settings that may not be available in the
printed copy.
[4]
1) Preparation Instructions:
Prior to installing your water softener follow these instructions
A
Add the plumbing fittings
Remove the red fastened
clips.
Apply silicon lube to the orings.
Push the o-rings into the
bypass assembly.
Put back on the red
fasteners.
B
Check the water flow
direction arrows on the
control valve. The flow
direction arrows must
match the direction of
your water flow.
C
Open the bypass valves
(meter models only)
Check both bypass valves
are open.
Use the tool supplied to turn
the red bypass valves fully
clockwise. The valves are
open when both are parallel.
NOTE: Failure to open
these will bypass the
water softener leaving you
with hard water.
[5]
1) Preparation Instructions:
NOTE: A loose seal on
the brine suction hose is
the most common cause
of malfunctioning. Use
an adjustable wrench to
make sure the plastic
nut is airtight.
D
Check brine suction hose
Check that the end of the
brine suction hose is
connected securely inside
the brine tank.
The brine suction pipe on
the inside should be wedged
at the size of the blue
vessel. The flotation buoy
end of the pipe should be on
the bottom of the brine tank.
E
Adjust the mixing valve
The mixing valve should be
turned fully anti-clockwise in
order for your unit to
produce soft water.
F
Switch the overflow to the
outside.
Locate the overflow fitting on
the side of the brine tank.
Your overflow fitting will
need to be switched to the
outside as shown, as it is
turned inside during
transport.
[6]
2) Installing Your Water Softener:
We recommend watching the videos on www.water2buy.com
A
Decide on where you want
to locate your water
softener, usually a water
softener is located where the
mains water enters your
home. Typical locations
include; under the kitchen
sink, basement, garage or
pump-house. You will need
to locate near a power
source and drainage.
B
Turn off the mains water to
your home before
proceeding.
Cut the incoming water
mains pipe before any
branches of the mains water
pipe to ensure the whole
house has softened water.
IMPORTANT: Make sure
the cut is taken before the
tee piece for the pipe going
to the water storage tank.
C
Install an elbow joint on your
mains water pipe at both
ends of the cut.
Your local plumbing
regulations may require you
to install a ‘Non-return’ valve
on your mains water pipe.
[7]
2) Installing Your Water Softener:
D
Connect the mains water
pipe to the water inlet on the
control valve.
It’s important that you
check the water
directional flow
arrows on your unit.
E
Drill a 15mm hole through
the outside wall for a waste
pipe.
Drill another 15mm hole
through the outside wall for
the overflow pipe.
F
Locate the waste fitting on
the control valve.
Using 15mm tubing, connect
the waste fitting on the
control valve to a suitable
drain outside the building.
[8]
2) Installing Your Water Softener:
G
The waste pipe should not
be connected directly to the
drain; a 15mm air gap
should be left between the
waste pipe and the drain.
The overflow and the waste
pipe should not be joined
together.
H
Fill the tank with water
softener salt. Salt levels
need to be maintained at
approximately 100mm above
the bottom of the tank and
50mm from the top of the
tank.
Add 3-4 litres of water into
the tank on top of the salt.
I
Turn back on the mains
water.
Plug-in your water2buy
water softener.
Proceed with configuring the
settings on your unit. Refer
to your product manual for
guidance.
Check for leaks. We recommend regular checks for leaks for the first 24 hours after install.
IMPORTANT: Check for leaks at all joints and connections after turning on the mains
water. After 3 hours check for leaks at all joints and connections.
We recommend a further check after 24 hours.
[9]
3) Water Softener Settings: Meter Softeners
Meter Controls
•
•
•
•
•
Press
Press
Press
Press
Press
to enter the menu.
to select a menu item.
the value starts flashing and can be edited.
to change the value.
to save the setting.
REGIONAL MEASUREMENT UNITS.
The Default setting is Metric. We recommend leaving the default
REGENERATION TYPE.
This is set to Meter Delayed by default. We recommend leaving this value
at the default setting.
TIME
14:42
SET CURRENT TIME.
Setting the correct time is very important. Using an incorrect time will cause
the water softener to regenerate at the wrong time of the day.
Reset the time after power outages and summertime and wintertime clock
change.
REGENERATION TIME.
Set the time of the day that you would like the unit to perform regeneration.
We recommend using 3am when the water supply is not in use. Reset the
regeneration time after power outages and summertime and wintertime
clock change.
REG.CAP.
00.00T
REGENERATION CAPACITY.
Failure to adjust this setting correctly will result in hard water.
If you do not know your water hardness then you can enter the basic
settings below.
Model
Reg. Cap.
200
00.60T
500
01.40T
800
02.00T
For optimal performance, measure your water hardness and refer to the
‘REGENERATION CAPACITY TABLE’ on the next page of this manual to
get the optimal setting for your household.
BACKWASH
3 MIN
BACKWASH TIME.
Select time based on table below.
Model
200
Min
5
[10]
500
5
800
8
3) Water Softener Settings:
BRINE
18 MIN
RINSE
5 MIN
BRINE TIME.
Select time based on model below.
Model
Min
200
19
500
20
800
47
500
5
800
5
500
06.0
800
09.0
RINSE TIME.
Select time based on model below.
Model
Min
200
5
REFILL TIME.
Select time based on model below.
Model
Min
200
04.0
Optimal Performance:
Regeneration Capacity For Optimal Performance
A) Select the row with the number of people in your house.
B) Select the column with the closest water hardness.
C) Where the two values intersect you will get your regeneration capacity.
Example (highlighted) shows that the correct regeneration capacity for a model W2B 200 water softener:
A) With 4 people in the house and a
B) water hardness of 300ppm
C) is 0.96T.
[11]
3) Water Softener Settings:
`
Optimal Performance: REGENERATION CAPACITY TABLE (REG.CAP.)
W2B 200
(Example highlighted)
A
B
250
340
430
510
600
680
850
14.007
19.05
24.092
28.575
33.617
38.099
47.642
°dH
°TH
9.5249
17
25
34
43
51
60
68
85
1
2
3
4
3.33
2.95
2.57
2.19
2.09
1.71
1.34
0.96
1.48
1.1
0.72
0.96
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
C
^ Number of people in your home
W2B 500
Water Hardness >
PPM
170
250
340
430
510
600
680
850
14.007
19.05
24.092
28.575
33.617
38.099
47.642
°dH
°TH
9.5249
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
5.11
4.73
4.35
3.98
3.6
3.22
2.84
3.28
2.9
2.53
2.15
1.77
1.39
1.01
2.37
1.99
1.61
1.23
0.85
0.85
0.85
1.82
1.44
1.06
0.68
0.68
0.68
0.68
1.45
1.07
0.7
~
~
~
~
1.19
0.81
0.43
~
~
~
~
0.99
0.62
~
~
~
~
~
0.72
0.34
~
~
~
~
~
^ Number of people in your home
W2B 800
Water Hardness >
PPM
170
250
340
430
510
600
680
850
14.007
19.05
24.092
28.575
33.617
38.099
47.642
°dH
°TH
9.5249
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
^ Number of people in your home
[12]
4) Water Softener Settings: Timer Softeners
Timer Controls
1.
2.
3.
4.
5.
6.
Manual backwash knob.
24-hour gear.
Skipper wheel shows every other day backwash.
Red pointer.
Time of day arrow.
Red time set button.
Set the current time
•
•
•
•
•
•
Push in the red time set button (6)
Adjust the 24hour gear wheel (2)
Point the hour arrow (5) is to the current time.
The 24hour gear wheel (2) is the rear dial.
Let out the red time set button (6)
Twist the 24hour gear until it clicks, the click engages the timer
Set the regeneration frequency
IMPORTANT: Your water softener has been pre-programmed to regenerate at 2am each morning.
IMPORTANT: The pins must be pushed out at equal distances apart.
Push all the pins on the skipper wheel in before beginning the configuration.
Push IN = OFF
Push OUT = ON
A) Select the row with the number of people in your house.
B) Select the column with the closest water hardness in parts per million.
C) Where the two values intersect you will get the number of pins that you should push out.
Example (highlighted) shows that the correct number of pins to push for a model W2B 110 water
softener,
A) With 4 people in the house and a
B) water hardness of 250ppm
C) is 6.
So you need to push out pins 2, 4, 6, 8, 10, 12. (equal distances apart.)
[13]
4) Water Softener Settings: Timer Softeners
W2B 110
(Example highlighted)
A
B
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
1
2
4
4
2
4
6
6
2
4
6
12
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
C
^ Number of people in your home
W2B 300
Water Hardness >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
1
2
2
3
4
4
6
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
^ Number of people in your home
W2B 700
Water Hardness >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
1
1
2
2
3
4
4
4
1
2
3
4
4
4
6
6
1
2
4
4
6
6
6
12
2
3
4
6
6
12
12
12
2
4
4
6
12
12
12
12
2
4
6
6
12
12
12
12
2
4
6
12
12
12
12
12
3
6
12
12
12
12
12
12
^ Number of people in your home
[14]
5) Water Softener Troubleshooting: www.water2buy.com
WHAT KIND OF SALT IS BEST?
All Water2buy TM water softeners are designed to use any water softeners salt of good quality, including “rock,” “pellet,”
“solar,” or “evaporated” types. All rock salt, regardless of source, contains insoluble material, which collects at the bottom
of the salt storage tank and requires periodic clean out.
If purified salt products are used, the salt storage compartment will require less frequent clean out, but you must check
more frequently to prevent a “bridging” problem.
HOW CAN I START A MANUAL
REGENERATION CYCLE?
Do not run a manual backwash immediately before, after or
during an automatic backwash. Make sure the backwash
knob is at the ‘SERV’ position before beginning. Make sure
the backwash knob returns to the ‘SERV’ position when the
cycle is complete.
You can start a manual regeneration by turning the
manual backwash knob clockwise to the first position.
The process will take approximately 1 hour.
HOW MUCH SALT SHOULD I PUT INTO THE BRINE TANK?
Salt levels need to be maintained at approximately 100mm above the bottom of the tank and 50mm from the top of
the tank.
CAN I ADJUST THE SALT REFILL ON THE TIMER-CONTROLLED UNIT?
The salt refill is preset for you. Should you need to adjust, you will need to unscrew the back plate on the control
valve.
Refill volume can be adjusted through refill regulator (2).
To adjust the refill volume, release the screw (1) by a half turn, and then turn the Refill Regulator to the correct
volume to ‘2’. Finally tighten the screw (1).
[15]
5) Water Softener Troubleshooting: www.water2buy.com
I’M GETTING HARD WATER WHAT SHOULD I DO?
If you unexpectedly experience hard water, make these simple checks before calling Water2buy.
RUN MANUAL REGENERATION
See "HOW CAN I START A MANUAL
REGENERATION CYCLE?"
POWER SUPPLY
Check your power supply cable. Check that is plugged fully into the electric outlet. Be sure that the power outlet is
switched on. Reset softener to proper time of day and then plug in.
BLOWN FUSE
Check the house fuse or circuit breaker panel. Replace a blown-out fuse or reset an open circuit breaker. Consult a
registered electrician when dealing with any electrical
POWER FAILURE
Any interruption in your power supply, or time changes, such as daylight savings, will disrupt your softener’s
recharge schedule by causing the timer to run off schedule. Reset time to the correct time of day.
SALT SUPPLY
Check it. Refill if necessary and wait approximately four hours for the salt to dissolve before initiating a recharge
cycle.
INCREASED USAGE
Guests, family additions, new water-using appliances, etc. all will result in more water usage and will require more
capacity from your softener. You can reprogram your recharging schedule by following the directions on adjustments
for your softener in this manual.
NO WATER
If you aren’t getting any water flow at all, make sure your water supply is working. Open a tap ahead of the softener
(outside tap) to see if you have any water pressure.
CONTINUOUS FLOW TO DRAIN
If water runs to drain continuously. Check to make sure unit is not in regeneration. If it is regenerating, allow unit to
finish cycle, and then reset time of day if necessary.
SALT BRIDGING
Salt “bridging” occurs when a gap has formed between the salt and the water preventing the salt from dissolving in
the water to make brine. No brine = no soft water. High humidity and/or use of some brands of purified salt products
may cause a salt bridge to form.
The best way to check and eliminate a salt bridging problem is to take a brush handle then carefully begin to probe
down through the salt with the handle. Continue to probe and break up the bridge.
MIXING VALVE
If your unit has an optional mixing valve installed you need to turn it fully anti-clockwise hand tight. Marked A in
diagram.
[16]
5) Water Softener Troubleshooting: www.water2buy.com
THE BRINE TANK IS OVERFLOWING WAHT SHOULD I DO?
TIGHTEN THE BRINE SUCTION HOSE CONNECTION
Tighten the plastic nut (B) and brass nut (A) make sure the seal on both is airtight.
TIGHTEN THE CONNECTION BETWEEN THE CONTROL VALVE AND VESSEL
This is the threaded joint (C) in picture above where the control valve joins onto the brine tank. Hold the vessel
steady inside the tank and twist the control valve tight.
CLEAN THE INJECTORS
Unplug the control valve.
Turn the bypass valves fully anticlockwise into bypass position (perpendicular).
Using a screwdriver, remove injector screen and injector cap (A)
Use a screwdriver to unscrew the outer injector (B).
Insert the screwdriver and unscrew the inner injector (C).
Tilt the unit to remove the inner injector. Caution the unit may be heavy, seek assistance.
Remove the screen gauze.
Clean screen gauze using a fine brush.
Flush the gauze with water until clean.
Flush water into the injector recess of the valve to flush out debris.
Clean the injector with a pin or paperclip.
Lubricate the O-rings on the injector. Lubricate the injector cap and lubricate the injector screen with silicone
lubricant.
Reinstall the injector, injector cap and injector screen. Do not over-tighten the plastic cap. Seat the cap lightly into
position. Over tightening may cause breakage of the plastic cap that may not be immediately evident.
Plug in the control valve power.
Follow the setup and configuration process for your unit.
Slowly turn the bypass valves clockwise to open.
[17]
5) Water Softener Troubleshooting: www.water2buy.com
SERVICE OF YOUR WATER SOFTENER
We recommend watching the videos on www.water2buy.com
Following these simple steps will ensure continued trouble free service, and will keep your water softener looking like new
for years.
Do not place heavy objects on top of the salt storage tank or case.
Use only mild soap and warm water when cleaning the exterior of the softener. Never use harsh, abrasive cleaning
compounds or those, which contain acid, such as vinegar, bleach and similar products.
WARNING: Protect your water softener and the entire drain line from freezing temperatures.
DANGER: If your unit should freeze, do not attempt to disassemble it. Contact Water2buy.com
The timer is very accurate. Keep setting correct to assure recharging at the proper time.
A periodic clean out of the Salt Storage Tank is necessary to keep your Water2buy Water Softener at peak operating
efficiency. Do it at least every 2 years when the salt supply is low. Follow these step-by-step procedures:
Remove the salt storage tank cover and the cap from the brine valve chamber.
If you’d like to save any clean, dry salt remaining in the tank, remove it and place it in a clean container.
Using a scoop, dig out and discard as much remaining salt, water and debris as possible.
Lay the salt tank on its side and direct a brisk stream of water from your garden hose to its inside to rinse out all residue.
Using a household scrub brush and a mild soapy solution, clean the salt plate. This will complete the tank cleaning.
Fill the salt storage tank with 10-15cm of water.
Fill the tank with salt to within a few cm’s from the top.
The technology upon which the control valve is based is well established and proven in service over many years.
However, should a problem or question arise regarding the operation please refer to table below.
IMPORTANT: Service procedures that require the water pressure to be removed from the system are marked with a ! after
the possible cause.
Problem
1. Control will not regenerate
automatically.
2. Control regenerates at the
wrong time of day.
3. Control will not draw brine.!
Problem Cause
a. Transformer or motor not connected.
b. Defective timer motor.
c. Skipper pins not out on timer skipper
wheel.
a. Timer set incorrectly
a. Low water pressure.
b. Drain line blocked.
c. Injector blocked.
d. Injector defective.
4. System using more or less salt
than salt dial setting.!
a. Foreign matter in controller causing
incorrect flow rates.
b. Defective controller
5. Intermittent or irregular brine
draw.!
a. Low water pressure.
b. Defective injector.
6. No conditioned water after
regeneration.!
a. No salt in brine tank.
b. Injector plugged.
c. Air check valve closes prematurely.
7. Control backwashes or purges
a. Incorrect drain controller
[18]
Solution
a. Connect power.
b. Replace motor.
c. Pull out pins for days regeneration required.
a. Correct time setting
according to instructions.
a. Unblock.
b. Change drain to remove restriction.
c. Clean injector and screen.
d. Replace injector.
a. Remove brine control and
flush out foreign matter.
Manually position control to
brine/slow rinse to clean
controller (after so doing
position control to "purge” to
remove brine from tank).
b. Replace brine control.
a. Set pump to maintain 1 bar (14 psi)
at softener.
b. Replace injector.
a. Add salt to brine tank.
b. Clean injector and screen.
c. Replace or
repair air check brine suction pipe if needed.
a. Replace with correct size
at excessively low or high rate.!
used.
b. Foreign matter affecting
controller operation.
controller.
b. Remove drain controller and
clean ball and seat
8. Unit fails to initiate a
regeneration cycle.
1. No power supply.
Check electrical service, fuse, etc.
2. Power failure
Reset time of day.
1. By-pass valve open.
Close by-pass valve.
2. Out of salt.
Add salt to tank.
3. Plugged injector / screen
Clean parts.
4. Flow of water blocked to brine tank.
Check brine tank refill rate.
5. Hard water in hot water tank.
Repeat flushing of hot water tank required.
6. Leak between valve and central tube.
Check if central tube is cracked or o-ring is
damaged. Replace faulty parts.
7. Internal valve leak.
Replace valve seals, spacer, and piston
assembly.
1. Refill time is too long.
Check refill time setting.
1. Iron or scale builds up in line feeding unit.
Clean pipes.
2. Iron build up inside valve or tank.
Clean control and add resin cleaner to clean
bed. Increase regeneration frequency.
3. Inlet of control plugged due to foreign
material.
Remove piston and clean control valve.
1. Air in water system.
Check well system for proper air eliminator
control.
2. Incorrect drain line flow control (DLFC)
button.
Check for proper flow rate.
1. Plugged injector or screen.
Clean parts.
2. Foreign material in brine tank.
Clean parts.
1. Drain line flow control is plugged.
Clean parts.
2. Injector or screen is plugged.
Clean parts.
3. Inlet pressure too low.
Increase pressure to 25 PSI.
4. Internal valve leak.
Replace seals, spacers, and piston assembly
15. Valve continuously cycles.
1. Broken gear.
Replace faulty parts.
16. Flow to drain continuously.
1. Valve settings incorrect.
Check valve settings.
2. Foreign material in control valve.
Clean control.
9. Water is hard.
10. Salt use is high.
11. Low water pressure.
12. Resin in drain line.
13. Too much water in brine
tank.
14. Unit fails to draw brine.
[19]
SHOULD YOU NOTICE ANY NEW PROBLEMS WITH YOUR WATER, WATER2BUY HAS
THE CAPABILITIES TO SOLVE THEM.
Water2buy products and systems reduce both natural and man-made water pollutants; and provide the best water
3. Internal
leak.
for each specific use and application.
Your
new Water2buy water softener can be adjusted to handle to wide range
seals,
spacers,
and
piston assembly.
of water problems, but it does have limitations. It has been specified ontoReplace
the basis
of your
water
conditions
at the
time of sale. It is possible for the chemical makeup of your water to change in time, and such changes cannot be
predicted. Your needs and uses may also change. Water2buy is ready to help you if any problem should arise.
With Water2buy, you get more than a quality product. Our reputation is based on prompt, courteous, efficient
attention to your needs. Selling water softeners is our full-time business, and satisfied customers are our best
assets. YOU GET THE SECURITY OF DEALING WITH AN ORGANISATION THAT’S TRUSTED ALL OVER
EUROPE.
Water2buy is one of the leading brands of water softeners in the world. This leadership position is not awarded it is
earned. It means that a Water2buy product will never be an “orphan” because we will always stand behind our
warranties. It means that we will always strive to deserve your confidence.
Thank you for choosing Water2buy™ water filtration made easy.
© Copyright notice. Water2buy™ is a registered trademark; all images, logos text and diagrams belong to
water2buy. Copying of water2buy™ materials is strictly forbidden without prior written consent.
www.water2buy.com
[20]
[21]
D
E
U
T
S
C
H
•
[22]
[23]
[24]
[25]
[26]
[27]
REGIONAL
METRIC
METER
DELAYED
TIME
14:42
REG.TIME
03:00
REG.CAP.
00.00T
•
•
200
00.60T
500
01.40T
800
02.00T
[28]
BACKWASH
3 MIN
BRINE
18 MIN
RINSE
5 MIN
800
8
200
19
500
20
800
47
200
5
500
5
800
5
200
04.0
500
06.0
800
09.0
[29]
A
4
3.33
2.95
2.57
2.19
2.09
1.71
1.34
0.96
C
1.48
1.1
0.72
0.96
28.57
33.61
38.09
47.64
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
24.092
1.82
1.44
1.06
0.68
0.68
0.68
0.68
28.575
1.45
1.07
0.7
~
~
~
~
33.617
1.19
0.81
0.43
~
~
~
~
38.099
0.99
0.62
~
~
~
~
~
47.642
0.72
0.34
~
~
~
~
~
5.11
4.73
4.35
3.98
3.6
3.22
2.84
14.007
3.28
2.9
2.53
2.15
1.77
1.39
1.01
19.05
2.37
1.99
1.61
1.23
0.85
0.85
0.85
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
14.007
19.05
24.092
28.575
33.617
38.099
47.642
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
[30]
•
•
•
•
[31]
A
1
2
3
4
1
2
4
4
2
4
6
6
C
2
4
6
12
28.575
33.617
38.099
47.642
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
1
2
2
3
4
4
6
14.007
19.05
24.092
28.575
33.617
38.099
47.642
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
24.092
2
3
4
6
6
12
12
12
28.575
2
4
4
6
12
12
12
12
33.617
2
4
6
6
12
12
12
12
38.099
2
4
6
12
12
12
12
12
47.642
3
6
12
12
12
12
12
12
1
1
2
2
3
4
4
4
14.007
1
2
3
4
4
4
6
6
19.05
1
2
4
4
6
6
6
12
[32]
5) Wasserenthärter-Fehlersuchhilfe: www.water2buy.com
WAS FÜR SALZ IST AM BESTEN?
[33]
[34]
[35]
Solution
a. Niedriger Wasserdruck.
b. Defekter Injektor.
[36]
1. Umgehungsventil offen.
7. Interne Ventilleck.
[37]
2. Fremdstoff im Regelventil.
www.water2buy.com
[38]
[39]
F
R
A
N
Ç
A
I
S
[40]
[41]
[42]
Il est recommandé de regarder les vidéos sur www.water2buy.com
[43]
[44]
[45]
Appuyer sur
•
Appuyer sur
•
Appuyer sur
•
•
Appuyer sur
Appuyer sur
TIME
14:42
REG.CAP.
00.00T
200
00.60T
500
01.40T
800
02.00T
[46]
BACKWASH
3 MIN
BRINE
18 MIN
RINSE
5 MIN
REFILL
0.0 MIN
800
8
200
19
500
20
800
47
200
5
500
5
800
5
200
04.0
500
06.0
800
09.0
Performance optimale:
[47]
W2B 200
A
PPM
170
°TH
17
1
2
3
4
3.33
2.95
2.57
2.19
^
250
25
B
2.09
1.71
1.34
0.96
C
340
430
510
600
680
34
43
51
60
68
850
85
1.48
1.1
0.72
0.96
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
850
170
250
340
430
510
600
680
°TH
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
5.11
4.73
4.35
3.98
3.6
3.22
2.84
3.28
2.9
2.53
2.15
1.77
1.39
1.01
2.37
1.99
1.61
1.23
0.85
0.85
0.85
1.82
1.44
1.06
0.68
0.68
0.68
0.68
1.45
1.07
0.7
~
~
~
~
1.19
0.81
0.43
~
~
~
~
0.99
0.62
~
~
~
~
~
0.72
0.34
~
~
~
~
~
510
600
680
850
^
170
250
340
430
°TH
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
^
[48]
[49]
A
PPM
170
250
340
430
510
600
680
850
°TH
17
25
34
43
51
60
68
85
1
2
3
4
1
2
4
4
2
4
6
6
2
4
6
12
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
^
B
C
170
250
340
430
510
600
680
850
°TH
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
1
2
2
3
4
4
6
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
^
170
250
340
430
510
600
680
850
°TH
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
1
1
2
2
3
4
4
4
1
2
3
4
4
4
6
6
1
2
4
4
6
6
6
12
2
3
4
6
6
12
12
12
2
4
4
6
12
12
12
12
2
4
6
6
12
12
12
12
2
4
6
12
12
12
12
12
3
6
12
12
12
12
12
12
^
[50]
5) Résolution des problèmes: www.water2buy.com
[51]
5) Résolution des problèmes: www.water2buy.com
[52]
5) Résolution des problèmes: www.water2buy.com
[53]
[54]
[55]
www.water2buy.com
[56]
[57]
Č
E
S
K
Á
[58]
[59]
[60]
Doporučujeme se podívat na videa na webu www.water2buy.com
[61]
[62]
[63]
TIME
14:42
REG.CAP.
00.00T
[64]
BACKWASH
3 MIN
BRINE
18 MIN
RINSE
5 MIN
REFILL
0.0 MIN
500
5
800
8
200
19
500
20
800
47
500
5
800
5
500
06.0
800
09.0
200
5
200
04.0
[65]
A
B
250
340
430
510
600
680
850
14,0
19,05
24,09
28,57
33,61
38,09
47,64
°dH
°TH
mmol/l
9,52
17
25
34
43
51
60
68
85
1,7
2,5
3,4
4,3
5,1
6
6,8
8,5
1
2
3
3.33
2.95
2.57
2.19
2.09
1.71
1.34
0.96
1.48
1.1
0.72
0.96
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
4
C
^ Počet osob v domácnosti
250
340
430
510
600
680
850
9,52
14,0
19,05
24,09
28,57
33,61
38,09
47,64
17
25
34
43
51
60
68
85
1,7
2,5
3,4
4,3
5,1
6
6,8
8,5
1
2
3
4
5
6
7
5.11
4.73
4.35
3.98
3.6
3.22
2.84
3.28
2.9
2.53
2.15
1.77
1.39
1.01
2.37
1.99
1.61
1.23
0.85
0.85
0.85
1.82
1.44
1.06
0.68
0.68
0.68
0.68
1.45
1.07
0.7
~
~
~
~
1.19
0.81
0.43
~
~
~
~
0.99
0.62
~
~
~
~
~
0.72
0.34
~
~
~
~
~
^ Počet osob v domácnosti
250
340
430
510
600
680
850
14,0
19,05
24,09
28,57
33,61
38,09
47,64
43
51
60
68
85
4,3
5,1
6
6,8
8,5
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
°dH
°TH
mmol/l
9,52
17
25
34
1,7
2,5
3,4
1
2
3
4
5
6
7
8+
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
^ Počet osob v domácnosti
[66]
[67]
B
250
340
430
510
600
680
850
14,0
19,05
24,09
28,57
33,61
38,09
47,64
°dH
°TH
mmol/l
9,52
17
25
34
43
51
60
68
85
1,7
2,5
3,4
4,3
5,1
6
6,8
8,5
1
2
3
4
1
2
4
4
2
4
6
6
2
4
6
12
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
A
^
C
Počet osob v domácnosti
250
340
430
510
600
680
850
14,007
19,05
24,092
28,575
33,617
38,099
47,642
43
51
60
68
85
4,3
5,1
6
6,8
8,5
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
°dH
°TH
mmol/l
9,5249
17
25
34
1,7
2,5
3,4
1
2
3
4
5
6
7
1
2
2
3
4
4
6
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
^
Počet osob v domácnosti
250
340
430
510
600
680
850
14,007
19,05
24,092
28,575
33,617
38,099
47,642
43
51
60
68
85
4,3
5,1
6
6,8
8,5
2
4
4
6
12
12
12
12
2
4
6
6
12
12
12
12
2
4
6
12
12
12
12
12
3
6
12
12
12
12
12
12
°dH
°TH
mmol/l
9,5249
17
25
34
1,7
2,5
3,4
1
2
3
4
5
6
7
8+
1
1
2
2
3
4
4
4
1
2
3
4
4
4
6
6
1
2
4
4
6
6
6
12
2
3
4
6
6
12
12
12
^ Počet osob v domácnosti
[68]
[69]
[70]
[71]
6. Tvrdá voda po regeneraci.!
[72]
Zkontrolujte el. zdroj, pojistku, atd.
9. Tvrdá voda.
Zavřete bypass.
4. Tok vody do nádrže solanky blokován.
5. Tvrdá voda v bojleru.
2. Použit nesprávný odpadní regulátor
(DLFC).
1. Ucpaný odpadní regulátor (DLFC).
Nastavte vaše čerpadlo, aby udrželo 1,4 bar.
1. Nespravné nastavení.
[73]
www.water2buy.com
[74]
[75]
I
T
A
L
I
A
N
O
•
•
•
•
•
•
•
•
[76]
[77]
[78]
Si consiglia di guardare i video su www.water2buy.com
[79]
[80]
[81]
Premere
Premere
Premere
Premere
Premere
TIME
14:42
REG.CAP.
00.00T
[82]
BACKWASH
3 MIN
BRINE
18 MIN
RINSE
5 MIN
800
8
200
19
500
20
800
47
200
5
500
5
800
5
200
04.0
500
06.0
800
09.0
[83]
A
B
170
250
°dH
°TH
9.52
14.00
17
25
34
43
51
60
68
85
1
2
3
4
3.33
2.95
2.57
2.19
2.09
1.71
1.34
0.96
1.48
1.1
0.72
0.96
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
C
340
430
510
600
680
850
19.05
24.09
28.57
33.61
38.09
47.64
W2B 500
Durezza >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.52
14.00
19.05
24.09
28.57
33.61
38.09
47.64
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
5.11
4.73
4.35
3.98
3.6
3.22
2.84
3.28
2.9
2.53
2.15
1.77
1.39
1.01
2.37
1.99
1.61
1.23
0.85
0.85
0.85
1.82
1.44
1.06
0.68
0.68
0.68
0.68
1.45
1.07
0.7
~
~
~
~
1.19
0.81
0.43
~
~
~
~
0.99
0.62
~
~
~
~
~
0.72
0.34
~
~
~
~
~
W2B 800
Durezza >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.52
14.00
19.05
24.09
28.57
33.61
38.09
47.64
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
[84]
[85]
A
B
170
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
1
2
4
4
2
4
6
6
2
4
6
12
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
C
W2B 300
Durezza >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
1
2
2
3
4
4
6
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
W2B 700
Durezza >
PPM
170
250
340
430
510
600
680
850
°dH
°TH
9.5249
14.007
19.05
24.092
28.575
33.617
38.099
47.642
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
1
1
2
2
3
4
4
4
1
2
3
4
4
4
6
6
1
2
4
4
6
6
6
12
2
3
4
6
6
12
12
12
2
4
4
6
12
12
12
12
2
4
6
6
12
12
12
12
2
4
6
12
12
12
12
12
3
6
12
12
12
12
12
12
[86]
QUALE È IL TIPO DI SALE MIGLIORE?
TM
[87]
[88]
[89]
[90]
Aggiungere sale al serbatoio.
[91]
3. Perdite interne.
www.water2buy.com
[92]
[93]
E
S
P
A
Ñ
O
L
•
•
•
•
•
•
Llave ajustable
•
•
•
•
[95]
[96]
[97]
[98]
[99]
Controles Meter
•
•
•
•
•
REGIONAL
METRIC
METER
DELAYED
TIME
14:42
REG.TIME
03:00
REG.CAP.
00.00T
200
00.60T
500
01.40T
800
02.00T
[100]
BACKWASH
3 MIN
BRINE
18 MIN
RINSE
5 MIN
800
8
200
19
500
20
800
47
200
5
500
5
800
5
200
04.0
500
06.0
800
09.0
[101]
A
B
250
340
430
510
600
680
850
14.00
19.05
24.09
28.57
33.61
38.09
47.64
°dH
°TH
9.52
17
25
34
43
51
60
68
85
1
2
3
3.33
2.95
2.57
2.19
2.09
1.71
1.34
0.96
1.48
1.1
0.72
0.96
1.1
0.73
0.35
0.96
0.86
0.48
~
~
0.68
0.3
~
~
0.55
~
~
~
0.36
~
~
~
4
C
250
340
430
510
600
680
850
14.00
19.05
24.09
28.57
33.61
38.09
47.64
°dH
°TH
9.52
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
5.11
4.73
4.35
3.98
3.6
3.22
2.84
3.28
2.9
2.53
2.15
1.77
1.39
1.01
2.37
1.99
1.61
1.23
0.85
0.85
0.85
1.82
1.44
1.06
0.68
0.68
0.68
0.68
1.45
1.07
0.7
~
~
~
~
1.19
0.81
0.43
~
~
~
~
0.99
0.62
~
~
~
~
~
0.72
0.34
~
~
~
~
~
250
340
430
510
600
680
850
14.00
19.05
24.09
28.57
33.61
38.09
47.64
°dH
°TH
9.52
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
7.18
6.8
6.43
6.05
5.67
5.29
4.91
4.54
4.66
4.28
3.91
3.53
3.15
2.77
2.39
2.02
3.4
3.02
2.65
2.27
1.89
1.51
1.13
1.13
2.65
2.27
1.89
1.51
1.13
0.76
0.76
0.76
2.14
1.76
1.39
1.01
0.63
0.63
0.63
0.63
1.78
1.4
1.03
0.65
~
~
~
~
1.51
1.13
0.76
~
~
~
~
~
1.13
0.76
0.38
~
~
~
~
~
[102]
[103]
A
B
250
340
430
510
600
680
850
°dH
°TH
9.52
14.00
19.05
24.09
28.57
33.61
38.09
47.64
17
25
34
43
51
60
68
85
1
2
3
4
1
2
4
4
2
4
6
6
2
4
6
12
3
6
12
12
4
6
12
12
4
12
12
12
4
12
12
12
6
12
12
12
C
250
340
430
510
600
680
850
°dH
°TH
9.52
14.00
19.05
24.09
28.57
33.61
38.09
47.64
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
1
2
2
3
4
4
6
1
2
4
4
6
6
12
2
3
4
6
6
12
12
2
4
6
6
12
12
12
2
4
6
12
12
12
12
3
6
12
12
12
12
12
3
6
12
12
12
12
12
4
6
12
12
12
12
12
250
340
430
510
600
680
850
°dH
°TH
9.52
14.00
19.05
24.09
28.57
33.61
38.09
47.64
17
25
34
43
51
60
68
85
1
2
3
4
5
6
7
8+
1
1
2
2
3
4
4
4
1
2
3
4
4
4
6
6
1
2
4
4
6
6
6
12
2
3
4
6
6
12
12
12
2
4
4
6
12
12
12
12
2
4
6
6
12
12
12
12
2
4
6
12
12
12
12
12
3
6
12
12
12
12
12
12
[104]
¿QUÉ TIPO DE SAL ES EL MEJOR?
TM
[105]
[106]
[107]
2.
3.
a.
a.
b.
c.
d.
[108]
b.
5.
Retirada de salmuera
intermitente o irregular. !
a.
b.
6.
a.
b.
c.
7.
a.
b.
4.
a.
10. Se usa demasiada sal.
b.
a.
b.
a.
b.
c.
a.
b.
2. No hay sal.
9.
a.
1.
[109]
Revise los ajustes de la válvula.
Limpie el control.
3. Fuga interna.
www.water2buy.com
[110]">