advertisement
![2. Package Contents and Installation. Air Live SD-2020 | Manualzz 2. Package Contents and Installation. Air Live SD-2020 | Manualzz](http://s1.manualzz.com/store/data/000883793_1-65b9dd6ac435d79ca567bbeac9567a50-360x466.png)
2. Package Contents and Installation
2 2.
Package Contents and
Installation
2.1 Package Content
A user can find the following items in the package as below:
1. AirLive SD-2020 is the main element of the product.
2. Bundle CD includes Setup Wizard II, CamPro Express64, Quick Start Guide, User
Manual, and Video.
3. Quick Start Guide provides important information and instructions for installing this device.
4. Accessory Package
2.2 Connections
Power Source Requirement
This camera can work with 802.3at POE switch. However, if you need to operate this camera below 0 degree Celsius, please purchase the optional power adapter for the heater to work.
Switch/Connector
There are various connectors located on AirLive SD-2020’s back plate as shown in the figures below.
Please refer to the diagrams and tables accompanied with for using of each switch / connector.
AirLive SD-2020 User’s Manual 6
2. Package Contents and Installation
1. RJ45 LAN socket: Connect to PC or Hub/Switch.
For connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 cable to connect the Network
Camera to a 100Mbps Fast Ethernet network switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
Green Link Light indicates good network connection.
Power (orange color)
This LED is used to indicate whether DC power is on or not.
2. Alarm I/O:
AirLive SD-2020 supports 4 digital alarm inputs and 2 digital alarm outputs. Please make sure the alarm connections are properly wired before starting to configure alarm related settings in section “SystemÆApplication (Alarm Settings).”
Please refer to the pin definition table below for alarm system wiring.
7 AirLive SD-2020 User’s Manual
2. Package Contents and Installation
\
3. AC-in Jack: The input power is 24VAC.
Please refer to the illustrations below to connect power core through the supplied power adaptor.
Note: Supply the power to the Network Camera with the power adapter, which is Not included in package.
4. Audio I/O Connectors
Please refer to the illustrations below to set up the audio according to the audio pin definition.
AirLive SD-2020 User’s Manual 8
advertisement
Related manuals
advertisement
Table of contents
- 7 1. Overview
- 7 1.1 Introduction
- 7 1.2 Features
- 8 1.3 Product Specification
- 11 1.4 System Requirement
- 12 2. Package Contents and Installation
- 12 2.1 Package Content
- 12 2.2 Connections
- 15 2.3 Mounting the Camera
- 17 2.4 Connect to IP Camera
- 21 3. Using IP Camera via Web Browser
- 21 3.1 Windows Web Browser
- 23 4. Operating IP Camera via Mobile Phone
- 23 4.1 Using IP Camera via iPhone
- 26 5. Configuration of Main Menu
- 27 5.1 Live View
- 30 5.2 System
- 30 5.3 Streaming
- 30 5.4 PTZ
- 30 5.5 Logout
- 31 6. System
- 31 6.1 System
- 33 6.2 Security
- 39 6.3 Network
- 48 Application
- 53 Motion Detection
- 58 Network Failure Detection
- 60 Storage Management
- 62 Recording
- 63 Schedule
- 64 File Location
- 65 View Information
- 67 Factory Default
- 68 Software Version
- 69 Software Upgrade
- 70 Maintenance
- 71 7. Streaming
- 71 7.1 Video Format
- 73 7.2 Video Compression
- 75 7.3 Video OCX Protocol
- 76 7.4 Video Frame Rate
- 77 7.5 Audio
- 79 8. PTZ
- 79 8.1 Preset
- 80 8.2 Cruise
- 81 8.3 Auto Pan
- 83 8.4 Sequence
- 84 8.5 Home
- 85 8.6 Tilt Range
- 86 Privacy Mask
- 88 8.8 Camera-Exposure
- 89 Camera-WB
- 91 Camera-Misc