Insteon app for iPhone, iPad and iPod touch. INSTEON Configuring Wi-Fi Camera, Wi-Fi Camera
INSTEON Wi-Fi Camera is an easy-to-use device that will give you peace of mind. It is equipped with a night vision feature that will allow you to see what is happening in your home even when it is dark. The camera also has a built-in microphone and speaker, so you can hear and talk to people in your home from anywhere in the world. You can use the Insteon app to configure and control your camera, and to receive alerts when motion is detected. The camera can be configured to use either a wired Ethernet connection or a Wi-Fi connection, so you can place it anywhere in your home.
विज्ञापन
विज्ञापन
Use the Insteon app to configure and control your Insteon Wi-Fi Camera.
The Insteon app requires Insteon Hub (2242-222) or (2245-222).
7
Configure a Camera for Wired Ethernet iPhone, iPad and iPod touch
Launch the Insteon App.
Tap the drawer icon or swipe from the right edge of the display to open the drawer.
Tap Add a Device.
Tap Camera.
If you have not already done so, connect your camera to power and your router using the supplied ethernet cable.
It can take up to two minutes for your camera to complete its startup process.
When ready, tap Next.
Select the camera that you would like to configure.
8
Give your camera a user name and password. This information is used to secure your camera.
When ready, tap Next.
Configure a Camera for Wired Ethernet iPhone, iPad and iPod touch
?
The maximum password length is 12 characters
The password must contain letters and numbers only; no special characters
(!@#$%^&*, etc.) are permitted
The password cannot contain spaces
If the Next button is disabled, your password does not meet the password restrictions.
Select Use Wired Ethernet and then tap Next.
Wait while your camera’s settings are updated.
To see your camera when you are away from home, you will need to configure manual remote access. Write down the
IP Address displayed at the bottom of the screen and tap Next.
Name your camera, select an icon and add it to a room.
9
Configure a Camera for Wired Ethernet iPhone, iPad and iPod touch
Scroll down and tap Port.
Change the port from 80 to 25106.
If you are setting up more than one camera, increase the port number for each successive camera to ensure that every camera has a unique port number.
When ready, tap Done.
Return to Settings by dismissing
Edit Camera and Add Device.
Tap House.
10
Configure a Camera for Wired Ethernet iPhone, iPad and iPod touch
Write down the Gateway IP address and Subnet Mask.
?
You should now have the following information:
• Camera IP Address
• Camera Port
• Gateway IP Address
• Subnet Mask
11
Assign a Static IP Address
Mac or PC
Download and launch the
Camera Setup Assistant from your Mac or PC.
insteon.com/csa
Right-click (or control-click) on a Mac) and select Network
Configuration.
Uncheck Obtain IP from DHCP
Server. IP Address, Subnet Mask,
Gateway and DNS Server will auto-populate.
Enter your camera password and click
OK. It may take up to two minutes for your camera to restart.
Visit insteon.com/remoteaccess for instructions on configuring remote access.
You’re done setting up your
Insteon Wi-Fi Camera.
?
If the fields are empty, enter the information gathered throughout this document.
Use Gateway IP Address for both Gateway and DNS
Server addresses.
12
Configure a Camera for Wi-Fi iPhone, iPad and iPod touch
Launch the Insteon App Tap the drawer icon or swipe from the right edge of the display to open the drawer
Tap Add a Device
Tap Camera If you have not already done so, connect your camera to power and your router using the supplied ethernet cable.
It can take up to two minutes for your camera to complete its startup process.
When ready, tap Next.
Select the camera that you would like to configure
13
Configure a Camera for Wi-Fi iPhone, iPad and iPod touch
Give your camera a user name and password. This information is used to secure your camera.
When ready, tap Next.
Tap Use Wi-Fi and select your network from the list. If you don’t see your network, ensure that you’ve connected the antenna to your camera.
Enter your Wi-Fi network password and tap Next
Disconnect the ethernet cable from your camera and restart the camera by disconnecting and then reconnecting your camera’s power cable.
If you do not disconnect the ethernet cable, your camera will not switch to Wi-Fi.
To see your camera when you are away from home, you will need to configure manual remote access. Write down the
IP Address displayed at the bottom of the screen and tap Next.
Name your camera, select an icon and add it to a room.
14
Configure a Camera for Wi-Fi iPhone, iPad and iPod touch
Scroll down and tap Port.
Change the port from 80 to 25106.
If you are setting up more than one camera, increase the port number for each successive camera to ensure that every camera has a unique port number.
When ready, tap Done.
Return to Settings by dismissing
Edit Camera and Add Device.
Tap House.
15
Configure a Camera for Wi-Fi iPhone, iPad and iPod touch
Write down the Gateway IP address and Subnet Mask.
?
You should now have the following information:
• Camera IP Address
• Camera Port
• Gateway IP Address
• Subnet Mask
16
Assign a Static IP Address
Mac or PC
Download and launch the
Camera Setup Assistant from your Mac or PC.
insteon.com/csa
Right-click (or control-click) on a Mac) and select Network
Configuration.
Uncheck Obtain IP from DHCP
Server. IP Address, Subnet Mask,
Gateway and DNS Server will auto-populate.
Enter your camera password and click
OK. It may take up to two minutes for your camera to restart.
Visit insteon.com/remoteaccess for instructions on configuring remote access.
You’re done setting up your
Insteon Wi-Fi Camera.
?
If the fields are empty, enter the information gathered throughout this document.
Use Gateway IP Address for both Gateway and DNS
Server addresses.
17
Add an Already Configured Camera iPhone, iPad and iPod touch
Add an already configured camera if you have already setup an Insteon Wi-Fi Camera using its web browser interface or would like to re-add a camera that was previously configured using the Insteon app.
Launch the Insteon App Tap the drawer icon or swipe from the right edge of the display to open the drawer
Tap Add a Device
18
Add an Already Configured Camera iPhone, iPad and iPod touch
Tap Camera Tap Next.
Select that camera that you would like to add from the list of cameras
19
Add an Already Configured Camera iPhone, iPad and iPod touch
Enter your camera’s user name and password. When ready, tap Next.
To see your camera when you are away from home, you will need to configure manual remote access. Write down the
IP Address displayed at the bottom of the screen and tap Next.
?
If you have not already done so, you will need to configure manual remote access to see your camera when you are away from home. Follow these steps to Configure Manual
Remote Access.
Name your camera, select an icon and add it to a room.
When finished, tap Done.
You’re done setting up your
Insteon Wi-Fi Camera.
20
Add a Remote Camera iPhone, iPad and iPod touch
Add a remote camera if your camera has been previously setup and is not located on your local network.
Launch the Insteon App Tap the drawer icon or swipe from the right edge of the display to open the drawer
Tap Add a Device
21
Add a Remote Camera iPhone, iPad and iPod touch
Tap Camera Tap Next.
Tap My Camera Isn’t Listed
Tap Add a Remote Camera Enter your camera’s IP address or URL, port, user name and password. When ready, tap Done.
Name your camera, select an icon and add it to a room.
When finished, tap Done.
You’re done setting up your
Insteon Wi-Fi Camera.
22
Advanced Camera Configuration iPhone, iPad and iPod touch
Use advanced camera configuration if you would like to enter all of your camera’s network information at once or if you would like to control options like DHCP, IP address and port.
Launch the Insteon App Tap the drawer icon or swipe from the right edge of the display to open the drawer
Tap Add a Device
23
Advanced Camera Configuration iPhone, iPad and iPod touch
Tap Camera If you have not already done so, connect your camera to power and your router using the supplied ethernet cable.
It can take up to two minutes for your camera to complete its startup process.
When ready, tap Next.
Select that camera that you would like to configure from the list of cameras
24
Advanced Camera Configuration iPhone, iPad and iPod touch
Tap Advanced Setup Configure your camera as desired and tap Next
Wait while your camera’s settings are updated
If you have not already done so, you will need to configure manual remote access to see your camera when you are away from home.
Follow these steps to Configure
Manual Remote Access.
Name your camera, select an icon and add it to a room. When finished, tap Done.
You’re done setting up your
Insteon Wi-Fi Camera.
25
डाउनलोड
विज्ञापन