advertisement
TH2515 Operation Manual
The color and arrow of the test cable should correspond to that of socket on panel, thus to avoid abnormal measurement.
8) [TRIGGER]
When the trigger mode is set as MANU (manual), pressing this key can trigger the instrument manually.
9) [ENTER]
Press this key to terminate and store input data.
10) Universal Arrow Keys
There are four arrow keys: up, down, left and right arrow keys.
11) Trademark and Model
Show instrument trademark and model.
12) POWER
It is the power switch.
2.2
Introduction to Rear Panel
Figure 2-2 shows the rear panel of TH2515.
1 2 3 4 5 6
GPIB
RS-232C
S/N:
R5-211-00001
LAN USB EXT HOLD
!
~
110V-240V
50/60Hz 30VA
HANDLER
10 9 8 7
Figure 2-2 Rear Panel
1) GPIB Interface (Option)
The GPIB interface is used to communicate with PC and further construct a GPIB test system.
2) Ground Terminal
This terminal connects the instrument chassis thus to protect or shield ground connection.
3) RS232C Serial Interface
It realizes serial communication of the instrument with PC.
4) Nameplate
It shows the instrument model.
5) Fuse socket
Fuse will be placed in this socket to protect the instrument.
6) Power Socket
It is used to input AC power.
4
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 8 Warm-up
- 8 Other Features
- 9 Introduction to Front and Rear Panels
- 9 Introduction to Front Panel
- 10 Introduction to Rear Panel
- 11 Display Zone
- 12 Introduction to Buttons on Front Panel
- 12 [MEAS DISP]
- 12 [SYSTEM SETUP]
- 12 Simple Operation
- 13 Starting Up
- 14 Basic Operation
-
14
- 14 Measurement Functions
- 15 Measurement Range
- 16 Measurement Speed
- 16 File Manage
- 16 Tools
-
17
- 18 File Manage
- 18 Tools
- 18 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
19
- 20 STATIS DISP
- 21 Edge Mode and Settings of Its Relevant Values
- 21 Status ON/OFF
- 21 Parameters of Statistic Analysis
- 22 TOOLS
-
22
-
25
- 25 Temperature Correction
- 26 Temperature Conversion
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 29 Tools
- 31 System Setup and File Manage
- 31 System Setup
- 31 TouchTone
- 31 Language
- 32 Password
- 32 Bus Mode
- 33 Baud Rate
- 33 Bus Addr
- 33 EOC Signal
- 34 Err.OUT signal
- 35 Power Supply Frequency
- 35 Setting Time and Date
-
36
- 36 Introduction to Save/Recall
- 36 Structure of File Folder/File in a U Disk
- 41 IP ADDR
- 41 SUBNET MASK
- 41 GATEWAY
- 41 DNS SERVER1, DNS SERVER
- 42 Performance Index
- 42 Measurement Function
- 42 Measurement Parameters and Notations
- 42 Measurement Groups
- 42 Equivalent Mode
- 42 Range
- 42 Trigger
- 43 Mode of Test Terminal
- 43 Time Expenditure of Measurement
- 43 Average
- 43 Display Digits
- 44 Test Signal
- 44 Current range
- 44 Output Voltage of Open Circuit
- 44 Maximum Display Range
- 44 Measurement Accuracy
- 45 Basic Accuracy for Resistance Measurement
- 46 Accuracy for Temperature Measurement (Pt500)
- 46 Accuracy for Temperature Measurement (Analog Input)
- 47 Temperature correction factor
- 48 Remote Control
- 48 RS232C Connection
- 49 GPIB Bus (option)
- 51 GPIB Interface Function
- 51 GPIB Addressing
- 51 GPIB Bus Commands
- 52 SCPI (Standard Commands for Programmable Instruments)
- 53 LAN Remote Control System
- 55 Access TH2515 through a Browser
- 55 Access TH2515 through the Software of a Upper Computer
- 56 USBTMC Remote Control System
- 56 System Configuration
- 56 Install the Driver
- 57 USBVCOM Virtual Serial Port
- 57 System Configuration
- 57 Installing Driver
- 59 SCIP Command Reference
- 59 TH2515 Subsystem Commands
- 59 DISPlay Subsystem Commands
- 61 FUNCtion Subsystem Commands
- 65 APERture Subsystem Commands
- 66 TRIGger Subsystem Commands
- 67 FETCH? Subsystem Commands
- 69 TEMPerature Subsystem Commands
- 71 COMParator Subsystem Commands
- 74 BIN Subsystem Commands
- 79 STATistics Subsystem Commands
- 83 IO Subsystem Commands
- 83 MEMory Subsystem Commands
- 84 SYSTem Subsystem Commands
- 87 GPIB Common Commands
- 91 Handler Interface
- 95 Package Contents and Warranty
- 95 Package Contents
- 95 Marks
- 95 Package
- 96 Shipping
- 96 Storage
- 96 Warranty