advertisement
TH2515 Operation Manual
0.8
Anti-corrosion alloy Nickel: 2.5 to 4.0
Silicon: 0.5 to 1.0
---
0.80 to 0.85
0.25 to 0.45
30
980 to 1770
Soft aluminum
Hard-drawn aluminum
Aluminum alloy
Aluminum>99.5
Aluminum>99.5
2.7
2.7
0.63 to 0.64
0.60 to 0.62
42
40
Silicon: 0.4 to 0.6
Magnesium: 0.4 to
0.5
--- 0.50 to 0.55 36
Calculating the conductivity and the temperature coefficient of the copper wire:
Diameter [mm]
Aluminum: 99.2 to
98.9
Annealed
(Conductivity) copper Tinning and annealed copper (conductivity)
Hard-drawn copper
(Conductivity)
0.01 to 0.26
0.26 to 0.50
0.98
0.993
0.93
0.94
---
0.96
0.50 to 2.00
2.00 to 8.00
1.00
1.00
0.96
0.97
0.96
0.97
Temperature coefficient ( ) varies with environment temperature and material conductivity. It is supposed that the temperature coefficient of a material at 20 ℃ is coefficient ( ) at t ℃ will be as the following expression:
, its temperature
=
3.6.3
Types of Temperature Sensor
There are two temperature input types: PT500 and Analog Input.
PT500
Press the touch key T.SENS
to select the type of temperature input and select PT. The input type of the temperature is the platinum resistance temperature sensor. At this time, “PT500 temperature sensor” as standard in the instrument should be inserted into the temperature measurement input terminal.
Analog Input
Touch the T.SENS
soft key to select the temperature input type. AnLG_In is analog input (the range of the input voltage is 0-2V) and the corresponding forma is:
T
V
2
2
T
V
1
1
* ( InputVolta ge )
T 1 V
V
2
2
T
V
2
1
V 1
21
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 8 Warm-up
- 8 Other Features
- 9 Introduction to Front and Rear Panels
- 9 Introduction to Front Panel
- 10 Introduction to Rear Panel
- 11 Display Zone
- 12 Introduction to Buttons on Front Panel
- 12 [MEAS DISP]
- 12 [SYSTEM SETUP]
- 12 Simple Operation
- 13 Starting Up
- 14 Basic Operation
-
14
- 14 Measurement Functions
- 15 Measurement Range
- 16 Measurement Speed
- 16 File Manage
- 16 Tools
-
17
- 18 File Manage
- 18 Tools
- 18 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
19
- 20 STATIS DISP
- 21 Edge Mode and Settings of Its Relevant Values
- 21 Status ON/OFF
- 21 Parameters of Statistic Analysis
- 22 TOOLS
-
22
-
25
- 25 Temperature Correction
- 26 Temperature Conversion
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 29 Tools
- 31 System Setup and File Manage
- 31 System Setup
- 31 TouchTone
- 31 Language
- 32 Password
- 32 Bus Mode
- 33 Baud Rate
- 33 Bus Addr
- 33 EOC Signal
- 34 Err.OUT signal
- 35 Power Supply Frequency
- 35 Setting Time and Date
-
36
- 36 Introduction to Save/Recall
- 36 Structure of File Folder/File in a U Disk
- 41 IP ADDR
- 41 SUBNET MASK
- 41 GATEWAY
- 41 DNS SERVER1, DNS SERVER
- 42 Performance Index
- 42 Measurement Function
- 42 Measurement Parameters and Notations
- 42 Measurement Groups
- 42 Equivalent Mode
- 42 Range
- 42 Trigger
- 43 Mode of Test Terminal
- 43 Time Expenditure of Measurement
- 43 Average
- 43 Display Digits
- 44 Test Signal
- 44 Current range
- 44 Output Voltage of Open Circuit
- 44 Maximum Display Range
- 44 Measurement Accuracy
- 45 Basic Accuracy for Resistance Measurement
- 46 Accuracy for Temperature Measurement (Pt500)
- 46 Accuracy for Temperature Measurement (Analog Input)
- 47 Temperature correction factor
- 48 Remote Control
- 48 RS232C Connection
- 49 GPIB Bus (option)
- 51 GPIB Interface Function
- 51 GPIB Addressing
- 51 GPIB Bus Commands
- 52 SCPI (Standard Commands for Programmable Instruments)
- 53 LAN Remote Control System
- 55 Access TH2515 through a Browser
- 55 Access TH2515 through the Software of a Upper Computer
- 56 USBTMC Remote Control System
- 56 System Configuration
- 56 Install the Driver
- 57 USBVCOM Virtual Serial Port
- 57 System Configuration
- 57 Installing Driver
- 59 SCIP Command Reference
- 59 TH2515 Subsystem Commands
- 59 DISPlay Subsystem Commands
- 61 FUNCtion Subsystem Commands
- 65 APERture Subsystem Commands
- 66 TRIGger Subsystem Commands
- 67 FETCH? Subsystem Commands
- 69 TEMPerature Subsystem Commands
- 71 COMParator Subsystem Commands
- 74 BIN Subsystem Commands
- 79 STATistics Subsystem Commands
- 83 IO Subsystem Commands
- 83 MEMory Subsystem Commands
- 84 SYSTem Subsystem Commands
- 87 GPIB Common Commands
- 91 Handler Interface
- 95 Package Contents and Warranty
- 95 Package Contents
- 95 Marks
- 95 Package
- 96 Shipping
- 96 Storage
- 96 Warranty