advertisement
TH2515 Operation Manual
5.3.4
Temperature correction factor
When the instrument is used under the following environmental conditions:
0 ℃ ~18 ℃ , ≤80%RH; 28 ℃ ~40 ℃ , ≤80%RH
Measurement Accuracy: Multiply the basic measurement accuracy value listed in chapter 5.3.1
-5.3.4 by the temperature correction factor K in the following table.
Temperature( ℃ ) 0 - 5 5 - 18 18 - 28
Temperature correction factor K
4 2 1
28 - 35
2
35 - 40
4
-------------------------------------------------------------------------------------------------------------------------------
Note: Rd is the digit reading of measuring instrument; Fs is the full range.
-------------------------------------------------------------------------------------------------------------------------------
41
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 8 Warm-up
- 8 Other Features
- 9 Introduction to Front and Rear Panels
- 9 Introduction to Front Panel
- 10 Introduction to Rear Panel
- 11 Display Zone
- 12 Introduction to Buttons on Front Panel
- 12 [MEAS DISP]
- 12 [SYSTEM SETUP]
- 12 Simple Operation
- 13 Starting Up
- 14 Basic Operation
-
14
- 14 Measurement Functions
- 15 Measurement Range
- 16 Measurement Speed
- 16 File Manage
- 16 Tools
-
17
- 18 File Manage
- 18 Tools
- 18 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
19
- 20 STATIS DISP
- 21 Edge Mode and Settings of Its Relevant Values
- 21 Status ON/OFF
- 21 Parameters of Statistic Analysis
- 22 TOOLS
-
22
-
25
- 25 Temperature Correction
- 26 Temperature Conversion
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 29 Tools
- 31 System Setup and File Manage
- 31 System Setup
- 31 TouchTone
- 31 Language
- 32 Password
- 32 Bus Mode
- 33 Baud Rate
- 33 Bus Addr
- 33 EOC Signal
- 34 Err.OUT signal
- 35 Power Supply Frequency
- 35 Setting Time and Date
-
36
- 36 Introduction to Save/Recall
- 36 Structure of File Folder/File in a U Disk
- 41 IP ADDR
- 41 SUBNET MASK
- 41 GATEWAY
- 41 DNS SERVER1, DNS SERVER
- 42 Performance Index
- 42 Measurement Function
- 42 Measurement Parameters and Notations
- 42 Measurement Groups
- 42 Equivalent Mode
- 42 Range
- 42 Trigger
- 43 Mode of Test Terminal
- 43 Time Expenditure of Measurement
- 43 Average
- 43 Display Digits
- 44 Test Signal
- 44 Current range
- 44 Output Voltage of Open Circuit
- 44 Maximum Display Range
- 44 Measurement Accuracy
- 45 Basic Accuracy for Resistance Measurement
- 46 Accuracy for Temperature Measurement (Pt500)
- 46 Accuracy for Temperature Measurement (Analog Input)
- 47 Temperature correction factor
- 48 Remote Control
- 48 RS232C Connection
- 49 GPIB Bus (option)
- 51 GPIB Interface Function
- 51 GPIB Addressing
- 51 GPIB Bus Commands
- 52 SCPI (Standard Commands for Programmable Instruments)
- 53 LAN Remote Control System
- 55 Access TH2515 through a Browser
- 55 Access TH2515 through the Software of a Upper Computer
- 56 USBTMC Remote Control System
- 56 System Configuration
- 56 Install the Driver
- 57 USBVCOM Virtual Serial Port
- 57 System Configuration
- 57 Installing Driver
- 59 SCIP Command Reference
- 59 TH2515 Subsystem Commands
- 59 DISPlay Subsystem Commands
- 61 FUNCtion Subsystem Commands
- 65 APERture Subsystem Commands
- 66 TRIGger Subsystem Commands
- 67 FETCH? Subsystem Commands
- 69 TEMPerature Subsystem Commands
- 71 COMParator Subsystem Commands
- 74 BIN Subsystem Commands
- 79 STATistics Subsystem Commands
- 83 IO Subsystem Commands
- 83 MEMory Subsystem Commands
- 84 SYSTem Subsystem Commands
- 87 GPIB Common Commands
- 91 Handler Interface
- 95 Package Contents and Warranty
- 95 Package Contents
- 95 Marks
- 95 Package
- 96 Shipping
- 96 Storage
- 96 Warranty