advertisement
Figure 32: Earth terminal of the DC distribution cabinet (left view)
Earth terminal
3. Connect one end of the earth cable to the user earth bar, and the other end to the earth bar in the AC distribution cabinet (See Figure 31 and Figure 32 ).
4. Lead out the DC earth cable from the positive busbar of the DC distribution cabinet, and connect it to the copper earth bar in the equipment room. The sectional area of the DC earth cable increases with system capacity, and should be at least 95mm 2 .
Connecting Cables Between Rectifier Cabinet and AC Distribution Cabinet
For Rack1000-A rectifier cabinet, choose one 160A MCB as AC input switch of the rectifier cabinet.
For Rack1500-A and Rack2000-A rectifier cabinets, choose two 160A MCBs as AC input switches of the rectifier cabinet.
Follow the steps below to install the AC input cables of the rectifier cabinet.
1. If the AC input cables of the rectifier cabinet are routed inside the cabinets, users can use the accessory cables as the AC input cables. Otherwise users need to prepare armored cables by themselves. If the system capacity exceeds 2000A, users need to prepare extra cables. The cable specification cannot greater than 50mm 2 . The wiring is shown in Figure 33 .
Vertiv | NetSure 801 CAA Series Power Supply System Instruction Manual 52
Figure 33: Connection of AC input cables of rectifier cabinet in AC distribution cabinet (front view)
2. Connect one end of the cable to the output terminal of the selected MCB in the AC distribution cabinet (do not connect the neutral line). The AC input cable wiring is shown in Figure 34 and Figure
35 .
Figure 34: AC input cable wiring (manually switch AC distribution cabinet, rear view)
Front view Right view
Vertiv | NetSure 801 CAA Series Power Supply System Instruction Manual
Top view
Input cable wiring area
Output cable wiring area one
Output cable wiring area two
53
Figure 35: AC input cable wiring (automatically switch AC distribution cabinet, rear view)
Top view
Output cable wiring area
Input cable wiring area
Right view Front view
3. Connect the other end of the cable to the AC input terminal of the rectifier cabinet. The connection of AC input cables in rectifier cabinet is shown in Figure 36 .
Vertiv | NetSure 801 CAA Series Power Supply System Instruction Manual 54
advertisement
Related manuals
advertisement
Table of contents
- 5 Safety Precautions
- 5 Electrical Safety
- 6 Battery
- 7 Others
- 8 OVERVIEW
- 8 Model Information
- 8 Overview
- 9 Components
- 9 Rectifier
- 11 Controller
- 11 AC Distribution Cabinet
- 16 DC Distribution Cabinet
- 24 Rectifier Cabinet
- 29 installation preparation
- 29 Installation Requirements
- 29 Environmental Requirements
- 29 Layout Requirements of The Equipment Room
- 32 Power Supply
- 33 Safety Protection
- 34 Equipment Running Environment Checklist
- 36 Storage Conditions
- 36 Installation Preparation
- 40 Unpacking Inspection
- 42 Installation
- 42 Cabinet Installation
- 42 Cabinet Placement
- 43 Mounting Large Side Door And Small Side Door
- 43 Installation on The Floor
- 45 Installation on Supporting Rack
- 46 Parallel Connection Between Cabinets
- 46 Parallel Connection with Copper Bars
- 49 Connecting Power Cables
- 50 Connecting Earth Cable
- 52 Distribution Cabinet
- 55 Connecting AC Input Cables
- 57 Connecting DC Emergency Lighting Cables (Optional)
- 58 Connecting DC Load Cables
- 59 Connecting Battery Cables
- 60 Installation Checklist
- 61 Installing Rectifier and Controller
- 61 Installing Rectifier
- 62 Installing Controller
- 63 Board
- 66 Cable
- 66 Connecting Rectifier Cabinet Communication Cable
- 68 Cabinet
- 69 Connecting Communication Cable of Distribution Cabinet
- 71 Installing Options
- 71 Installing Temperature Sensor
- 73 Testing
- 73 Note on Testing
- 73 Power-on
- 75 Setting Basic Parameters
- 75 Setting DIP Switch
- 76 Setting Basic Parameters for Controller
- 82 Checking Alarm and Operation Status
- 82 Testing Controller
- 84 Testing AC Distribution
- 85 Testing DC Distribution
- 86 Access Controller Through Web
- 94 Operation
- 94 Power Distribution LCD Operation
- 96 Controller Operation of Rectifier Cabinet
- 96 System Alarm and Status
- 96 Distribution Parameters Setting
- 96 Setting the Position Number of The Rectifier Manually
- 100 Adding Load
- 100 Adding Rectifier
- 101 Maintenance
- 101 Maintenance Requirements
- 101 General
- 101 Maintenance Tools and Equipment
- 102 Reference Technical Specification for Maintenance
- 104 Routine Maintenance Items
- 107 Routine Maintenance
- 108 Basic Inspection
- 108 Handling Controller Fault
- 108 Handling Rectifier Fault
- 110 Replacing Rectifier
- 111 Emergency Treatment
- 113 Appendix 1 Technical Parameters
- 116 Appendix 2 Alarm list
- 122 Appendix 3 ENGINEERING DESIGN DIAGRAM
- 138 APPENDIX 4 WIRING DIAGRAM
- 156 Appendix 5 SPARE PARTS