Help Displays For CST. Miller BIG BLUE 450 DUO CST, BIG BLUE 450 DUO CST (CST 282)
Add to My manuals68 Pages
advertisement
�
Complete Parts List is available at www.MillerWelds.com
8-12. Help Displays For CST
�
All directions are in reference to the front of the unit. All circuitry referred to is located inside the unit.
Help 1, 6, 7 Display
Indicates a malfunction in the primary power circuit. If this display is shown, contact a Factory Authorized Service Agent.
Help 2 Display
Indicates a malfunction in the thermal protection circuitry. If this display is shown, contact a Factory Authorized Service Agent.
Help 3, 5 Display
Indicates the unit has overheated. The unit has shut down to allow
the fan to cool it (see Section 4-7). Operation will continue when the
unit has cooled.
Help 8 Display
Indicates a malfunction in the secondary power circuit of the unit. If this display is shown, contact a Factory Authorized Service Agent.
OM-294672 Page 48
advertisement
Related manuals
advertisement
Table of contents
- 5 SECTION 1 – SAFETY PRECAUTIONS – READ BEFORE USING
- 5 Symbol Usage
- 5 Arc Welding Hazards
- 7 Engine Hazards
- 8 Compressed Air Hazards
- 8 Additional Hazards For Installation, Operation, And Maintenance
- 10 California Proposition 65 Warnings
- 10 Principal Safety Standards
- 10 EMF Information
- 11 SECTION 2 – CONSIGNES DE SÉCURITÉ - LIRE AVANT UTILISATION
- 11 Symboles utilisés
- 11 Dangers relatifs au soudage à l’arc
- 13 Dangers existant en relation avec le moteur
- 14 Dangers liés à l’air comprimé
- 15 Symboles de dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance
- 17 Proposition californienne 65 Avertissements
- 17 Principales normes de sécurité
- 18 Informations relatives aux CEM
- 19 SECTION 3 – DEFINITIONS
- 19 Additional Safety Symbol Definitions
- 22 Miscellaneous Symbols And Definitions
- 24 SECTION 4 – SPECIFICATIONS
- 24 Serial Number And Rating Label Locations
- 24 Software Licensing Agreement
- 24 Information About Default Weld Parameters And Settings
- 24 Weld, Power, And Engine Specifications
- 24 Dimensions, Weights, And Operating Angles
- 25 Environmental Specifications
- 25 Duty Cycle And Overheating
- 26 Volt-Ampere Curves: Stick
- 27 Volt-Ampere Curves: TIG
- 27 AC Generator Power Curve
- 27 Fuel Consumption
- 28 SECTION 5 – INSTALLATION
- 28 Installing Welder/Generator
- 29 Grounding Generator to Truck or Trailer Frame
- 29 Installing Exhaust Pipe
- 30 Connecting The Battery
- 30 Engine General Information
- 31 Engine Fuel And Coolant Prestart Information
- 32 Mitsubishi Engine Oil Prestart Information
- 32 Selecting Cable Sizes
- 33 Weld Output Terminals
- 34 Making Dual Operator CC Weld Connections With Common Work Cables
- 35 Paralleling CST Units For SMAW Welding
- 36 SECTION 6 – OPERATION
- 36 Front Panel Engine Controls
- 37 Operating Optional Engine Block Heater
- 38 Fuel/Hour Gauge Descriptions
- 39 Front Panel CST Controls
- 41 SECTION 7 – OPERATING AUXILIARY EQUIPMENT
- 41 Generator Power Receptacles
- 42 GFCI Receptacle Information, Resetting, And Testing
- 43 SECTION 8 – MAINTENANCE AND TROUBLESHOOTING
- 43 Maintenance Label
- 44 Routine Maintenance
- 45 Cleaning Unit
- 46 Servicing Air Cleaner
- 46 Battery Maintenance
- 47 Checking Generator Brush Assembly
- 47 Inspecting And Cleaning Optional Spark Arrestor Muffler
- 48 Servicing Engine Cooling System
- 48 Adjusting Engine Speed
- 49 Servicing Fuel And Lubrication Systems
- 50 Overload Protection
- 52 Help Displays For CST
- 53 Troubleshooting CST
- 53 Troubleshooting Generator
- 55 SECTION 9 – PARTS LIST
- 55 Recommended Spare Parts
- 56 SECTION 10 – ELECTRICAL DIAGRAMS
- 58 SECTION 11 – RUN-IN PROCEDURE
- 58 Wetstacking
- 59 Run-In Procedure Using Load Bank Or Resistance Grid
- 60 SECTION 12 – GENERATOR POWER GUIDELINES