- Sports & recreation
- Fitness, gymnastics & weight training
- Treadmills
- Alliance Laundry Systems
- SWD439C
- User manual
advertisement
![Water Supply Requirements. Alliance Laundry Systems SWD439C | Manualzz Water Supply Requirements. Alliance Laundry Systems SWD439C | Manualzz](http://s1.manualzz.com/store/data/002079776_1-7ea6e1919c265edb07203c41e5260bca-360x466.png)
Installation
Water Supply Requirements
WARNING
Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time.
W029
NOTE: Water supply faucets must fit standard
3/4 in. (19.1 mm) female garden hose couplings.
DO NOT USE SLIP-ON OR CLAMP-ON
CONNECTIONS.
NOTE: Water supply faucets should be readily accessible to permit turning them off when washer is not being used.
Water Temperature
Cold:
Recommended cold water temperature is 60° to 80°
Fahrenheit (16° to 27° Celsius).
Hot:
Recommended hot water temperature is 120° to 140°
Fahrenheit (49° to 60° Celsius).
Warm:
Mixture of hot and cold water (warm water temperature is dependent upon the water temperature and the pressure of both the hot and cold water supply lines).
IMPORTANT: Turn off water supply faucets after check-out and demonstration. Owner should turn off water supply whenever there will be an extended period of non-use.
NOTE: Longer inlet hoses are available (as optional equipment at extra cost) if the hoses
(supplied with the washer) are not long enough for the installation. Order hoses as follows:
No. 20617 Inlet Hose (8 ft.) (2.44 m)
No. 20618 Inlet Hose (10 ft.) (3.05 m)
1
1
2
1
Water Supply Faucets
Risers (Air Cushions)
Figure 40
WATER MIXING
VALVE
W005I
2
4
SWD548N
3
SWD548N
3
4
1
2
Water Supply Faucets
Cold Water Connection
Hot Water Connection
Water Inlet Hoses
Figure 39
Water Pressure
Pressure must be a minimum of 20 to a maximum of
120 pounds per square inch (138 to 827 kPa) static pressure measured at the faucet.
NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer and may not properly flush out the detergent dispenser.
Risers
Risers (or air cushions) may have to be installed if the pipes knock or pound when flow of water stops. The risers are more efficient when installed as close as possible to the water supply faucets (Refer to Figure 40).
2
W005I
800937 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
advertisement
Related manuals
advertisement
Table of contents
- 12 Step 3: Connect Drain Hose to Drain Receptacle
- 14 Step 4: (Gas Dryer Only) Connect Gas Supply Pipe
- 15 Step 5: (Electric Dryer Only) Connect Electrical Plug
- 16 Step 6: Connect Dryer Exhaust System
- 17 Step 7: Position and Level the Unit
- 18 (Washer Only)
- 18 Step 9: Wipe Out Inside of Washer Drum and Dryer Drum
- 19 Step 10: Plug In the Washer and Dryer
- 19 Step 11: Check Installation
- 19 Moving Unit to a New Location
- 20 Heat Source Check
- 20 Electric Dryers
- 20 Gas Dryers
- 21 Electrical Requirements
- 21 Washer
- 22 Electric Dryer
- 24 Electrical Plug Connection
- 24 Three-Wire Plug
- 25 Four-Wire Plug
- 27 Electrical Requirements
- 27 Gas Dryer
- 29 Gas Requirements
- 31 Water Supply Requirements
- 31 Water Temperature
- 31 Water Pressure
- 31 Risers
- 32 Location Requirements
- 33 Dryer Exhaust Requirements
- 33 Exhaust System Materials
- 34 Make-Up Air Requirements
- 34 Make-Up Air Dos and Don’ts
- 34 Exhaust Direction
- 35 Exhaust System
- 36 Exhaust System Maintenance
- 36 Dryer Airflow
- 37 Information for Handy Reference
- 45 Piezas de repuesto
- 47 Instalación
- 47 Dimensiones y especificiones
- 48 Antes de comenzar
- 48 Herramientas
- 48 Ubicación
- 48 Ducto de escape
- 48 Requisitos eléctricos
- 49 Instalación de la unidad
- 49 Paso 1: Coloque la unidad cerca del área de instalación
- 49 Paso 2: Conecte las mangueras de suministro de agua
- 50 de desagüe
- 52 suministro de gas
- 53 suministro de energía eléctrica
- 54 Paso 6: Conecte el sistema de escape de la secadora
- 55 Paso 7: Coloque la unidad en su lugar y nivélela
- 56 (en la lavadora solamente)
- 56 la secadora
- 57 Paso 10: Enchufe la lavadora y la secadora
- 57 Paso 11: Revise la instalación
- 57 Desplazamiento de la unidad a un nuevo sitio
- 58 Revisión de la fuente de calor
- 58 Secadoras eléctricas
- 58 Secadoras a gas
- 59 Requisitos eléctricos
- 59 Lavadora
- 60 Secadoras eléctricas
- 62 Conexión eléctrica
- 62 Enchufe de tres conductores
- 63 Enchufe de cuatro conductores
- 65 Requisitos eléctricos
- 65 Secadoras a gas
- 67 Requisitos de la fuente de suministro de gas
- 69 Requisitos de suministro de agua
- 69 Temperatura del agua
- 69 Presión del agua
- 69 Tubos ascendentes
- 70 Requisitos del lugar
- 71 Requisitos del sistema de escape de la secadora
- 71 Materiales del sistema de escape
- 72 Requisitos de aire de reposición
- 72 Qué hacer y qué no hacer
- 72 Dirección del escape
- 73 Sistema de escape
- 74 Mantenimiento del sistema de escape
- 74 Flujo de aire de la secadora
- 75 Información de referencia