Back of the Baby unit. British Telecom Digital Baby Monitor 300, PaperJet 300, 77497
Add to My manuals25 Pages
BT 77497 is a digital audio baby monitor from BT. The monitor has a range of up to 50m indoors and 300m outdoors. It features a high definition sound quality so you can hear your baby's every breath, gurgle, snuffle or cry with perfect clarity. The monitor also has a number of other features, including:
- A nightlight on the baby unit
- A crying alert on the parent unit
- A talk back feature that lets you instantly reassure and calm your baby
- A link light that provides continuous confidence that the parent unit is receiving a signal from the baby unit and will alert you if the link is lost
advertisement
8 Your BT Digital Baby Monitor 300
Back of the Baby unit
Power socket
For connection to the mains power socket via the power adapter cable supplied.
If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp
2250 Baby Monitor 300 UG Iss2.[2].indd 8 10/04/2014 11:06
Setting up
Parent unit
1. Plug one of the power adapter cables into the socket marked on the side of the Parent unit and plug the other end into the mains power wall socket and switch the power on.
2. Activate the batteries by pulling the plastic tab away from the top of the Parent unit and leave to charge for 24 hours to reach maximum charge.
24
WARNING!
Only use the power adapters supplied. Using incorrect power adapters may permanently damage your product.
Battery performance
Rechargeable batteries in the Parent unit will last approximately 16 hours during normal operation or 20 hours when Mute is switched on.
Please note that new batteries do not reach full capacity until they have been in normal use for several days.
The charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing the performance time of the Parent unit. Eventually they will need to be replaced. New batteries can be obtained from the
BT Digital Baby Monitor 300
Helpline on 0800 145 6789*.
The Parent unit rechargeable batteries will lose charge over a period of time, even if switched off.
9
If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp
2250 Baby Monitor 300 UG Iss2.[2].indd 9 10/04/2014 11:06
10 Setting up
Battery low warning –
Parent unit
When the batteries are low – approximately within 1 hour of running out – the Parent unit will emit a low battery alert and the low battery indicator on the unit will flash red.
To speed up the charging process turn the Parent unit off when charging if it’s not being used.
You can still use your Parent unit to monitor your baby even when the batteries are low, provided it remains plugged in and on charge.
WARNING
Always use rechargeable batteries in the Parent unit.
Only use the recommended type – 2 x AA NiMH 1300mAh batteries. Using other types could permanently damage the unit. Charge the batteries as instructed in this user guide.
The Parent unit can still be used when it is on charge.
Baby unit
1. Plug the remaining power adapter cable into the socket marked on the back of the Baby unit and plug the other end into the mains power and switch on.
Switch on and link the Parent and Baby units
1. Press and hold the button on the Baby unit for
1 second. The nightlight will briefly illuminate and then the green Link indicator will flash.
2. Press and hold the button on the Parent unit until all the LEDs on the unit briefly illuminate. The green Link indicator will flash.
Once the units are linked, the green Link indicators on the Parent and Baby units will stop flashing and remain a steady green. The units are now ready to use.
If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp
2250 Baby Monitor 300 UG Iss2.[2].indd 10 10/04/2014 11:06
Setting up 11
Important:
The link confirmation between the two units is vital for use so they can communicate. If the link between the units is broken at any time, the Link indicators on the Parent and Baby units will flash green as they try to search for each other. After 30 seconds, if the link is still broken they will flash red and you will also hear an alert signal from the Parent unit.
If the link is broken:
• check that the mains power is plugged in and switched on at the Baby unit
• check that both units are switched on
• check that the batteries are charged in the
Parent unit
• check that the Parent and Baby units are within range of each other (in ideal conditions the range is up to 300 metres outdoors and 50m indoors)
Removing the batteries
If you ever need to remove the batteries, simply slide open the battery compartment cover and use the ribbon to eject the batteries.
Positioning your units
The Baby unit should ideally be within 1m-2m of your baby for best performance.
If you place the Parent and
Baby units too close together you will hear a high pitched noise, this is normal. The units are designed to be located at a distance from one another, e.g. in separate rooms.
If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp
2250 Baby Monitor 300 UG Iss2.[2].indd 11 10/04/2014 11:06
advertisement
Related manuals
advertisement
Table of contents
- 7 Parent unit
- 8 Baby unit
- 9 Back of the Baby unit
- 13 Switch the Baby unit on
- 13 Switch the Parent unit on
- 13 Switch the Baby unit off
- 13 Switch the Parent unit off
- 14 Baby sound level LED indicators
- 15 loudspeaker volume
- 15 Crying alert
- 16 Nightlight
- 16 Switch Baby unit nightlight on/off
- 16 Adjust the nightlight brightness
- 16 Talk back
- 18 List of tones
- 19 Reset the units
- 19 Reset the Parent unit
- 19 Reset the Baby unit
- 22 Cleaning
- 22 Guarantee
- 23 Product disposal instructions
- 24 R&TTE
- 24 Declaration of Conformance
- 24 User Guide formats