Reset the units. British Telecom Digital Baby Monitor 300, PaperJet 300, 77497

18 Using your BT Digital Baby Monitor 300

Resetting the units is only advisable if you are experiencing difficulties with your product. It is a useful feature that ensures your Baby

Monitor is returned to its new

“out of the box” settings.

Reset the units

Resetting either units will return the settings at that unit back to its default settings.

Reset the Parent unit

1. Within 3 seconds of the Parent unit being switched on, press and hold the button for at least 10 seconds. You will hear a confirmation beep once the reset has been performed.

Reset the Baby unit

1. Within 3 seconds of the Baby unit being switched on, press the button for at least 10 seconds.

You will hear a confirmation beep once the reset has been performed.

If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp

2250 Baby Monitor 300 UG Iss2.[2].indd 18 10/04/2014 11:06

Help

Helpline

If you have any problems using your BT Digital Baby Monitor 300, call 0800 145 6789*.

Parent unit is beeping

Please see page 17 for the list of tones the Parent unit makes.

The Parent unit will beep for a number of reasons:

• The link has been lost between your units, see page 11. Check that the Baby unit Link indicator is illuminated. If not, please ensure that the power adapter is still connected and if this still does not switch on, please test into a different electrical socket.

• The crying alert is switched on, see page 14.

• The batteries are low, see pages 9-10.

• The Find button has been pressed on the Baby unit, see page 16.

If the Parent unit still beeps after checking the above, please try switching the Baby unit off at the power and removing the batteries for approximately 30 minutes. Ensure the Parent unit is clean by wiping with a damp cloth. If the problem persists call the Helpline for advice.

Link indicator does not come on

• Check that both the Baby and Parent units are switched on.

• Check that the batteries in the Parent unit are correctly installed and that they are charged.

• Check that the units are within range of each other.

• Check that the mains power is plugged in and switched on at the

Baby unit.

Link light is flashing green

• If you have pressed to use the Talk Back feature, the Link light will flash to indicate one-way communication between the units.

• The units are searching for a communication link.

19

If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp

2250 Baby Monitor 300 UG Iss2.[2].indd 19 10/04/2014 11:06

20 Help

• Check units are within range of one another.

• Check both units are turned on.

Link indicator is flashing red

• The Link between your units is broken. You will also hear an alert on the Parent unit to let you know there is no communication between the units. If this happens, check that the mains power (or batteries) is correctly connected and that the units are within range of one another. See page 10 for instructions on linking the units.

Battery low on Parent unit

• Put the Parent unit back on charge.

• Place the Parent unit back on charge as frequently as possible or ideally leave it on charge to ensure the batteries remain charged.

• To fully charge the batteries, the

Parent unit should be on charge for approximately 24 hours if switched on or 16 hours if switched off to reach maximum charge.

• To speed up the charging process turn the Parent unit off when charging if it is not being used.

Parent unit remains silent or very quiet

• You may have set the volume too low, see page 14 to increase the volume.

You can hear a high pitched noise

• The units might be too close to each other.

• The volume setting might be too high, see page 14.

Talk back feature is not working

• Check that the units are linked.

If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp

2250 Baby Monitor 300 UG Iss2.[2].indd 20 10/04/2014 11:06