advertisement
The following table describes the items in the previous figure.
Item
IPv6 Address
Count
Interval (in sec)
Size (in bytes)
Ping Results
Apply
Description
Enter the IP address or host name of the station you want the switch to ping. The initial value is blank. The IP Address or host name you enter is not retained across a power cycle. Host names are composed of series of labels concatenated with dots. Each label must be between 1 and 63 characters long, and the entire hostname has a maximum of 64 characters.
Enter the number of echo requests you want to send. The default value is 4. The value ranges from 1 to 5. The count you enter is not retained across a power cycle.
Enter the interval between ping packets in seconds. The default value is 1. The value ranges from 1 to 5. The interval you enter is not retained across a power cycle.
Enter the size of ping packet. The default value is 56. The value ranges from 8 to 5120. The size you enter is not retained across a power cycle.
Display the reply format of ping.
PING 2222:777 (2222:777): 56 data bytes
--- 2222:777 ping statistics ---
4 packets transmitted, 0 packets received, 100% packet loss
Or
PING 2222:717 (2222:717): 56 data bytes
64 bytes from 2222:717: icmp6_seq=0 ttl=128 time=10.0 ms
64 bytes from 2222:717: icmp6_seq=1 ttl=128 time=0.0 ms
64 bytes from 2222:717: icmp6_seq=2 ttl=128 time=0.0 ms
64 bytes from 2222:717: icmp6_seq=3 ttl=128 time=0.0 ms
--- 2222:717 ping statistics ---
4 packets transmitted, 4 packets received, 0% packet loss round-trip min/avg/max = 0.0/2.5/10.0 ms
Click Apply to display ping result for the IP address.
4.11.4
System Log
4.11.4.1
Logging Service
The Logging Service page allows you to setup the logging services feature for the system log.
To access this page, click Diagnostics > System Log > Logging Service.
Figure 4.111 Diagnostics > System Log > Logging Service
The following table describes the items in the previous figure.
Item
Logging Service
Apply
Description
Click Enabled or Disabled to set the Logging Service status.
Click Apply to save the values and update the screen.
106 EKI-9628G User Manual
The ensuing table for Logging Information settings are informational only and display the following: Logging Service.
4.11.4.2
Local Logging
The Local Logging page allows you to designate a local target when the severity criteria is reached.
To access this page, click Diagnostics > System Log > Local Logging.
Figure 4.112 Diagnostics > System Log > Local Logging
The following table describes the items in the previous figure.
Item
Target
Severity
Description
Enter the local logging target.
Click the drop-down menu to select the severity level for local log messages.
The level options are:
emerg: Indicates system is unusable. It is the highest level of severity
alert: Indicates action must be taken immediately
crit: Indicates critical conditions
error: Indicates error conditions
warning: Indicates warning conditions
notice: Indicates normal but significant conditions
info: Indicates informational messages
debug: Indicates debug-level messages
Click Apply to save the values and update the screen.
Apply
The ensuing table for Local Logging Settings Status settings are informational only and display the following: Status, Target, Severity and Delete (click to delete the desired target).
EKI-9628G User Manual 107
advertisement
Related manuals
advertisement
Table of contents
- 15 Specifications
- 16 Hardware Views
- 16 Front View
- 17 Rear View
- 18 Dimensions
- 18 Packing List
- 20 Warnings
- 21 Installation Guidelines
- 22 Environment and Enclosure Guidelines
- 22 Connecting Hardware
- 22 Verifying Switch Operation
- 23 Installing the Switch
- 23 Rack-Mounting
- 23 Installing and Removing SFP Modules
- 24 Installing SFP Modules
- 25 Removing SFP Modules
- 26 Connecting the Switch to Ethernet Ports
- 26 RJ45 Ethernet Cable Wiring
- 27 Connecting the Switch to Console Port
- 28 Power Supply Installation
- 28 Overview
- 29 Considerations
- 29 Grounding the Device
- 30 Wiring a Relay Contact
- 31 Wiring the Power Inputs
- 32 Reset Button
- 34 First Time Setup
- 34 Overview
- 34 Introduction
- 34 Administrative Interface Access
- 35 Using the Graphical (Web) Interface
- 35 Configuring the Switch for Network Access
- 36 Configuring the Ethernet Ports
- 37 Command Line Interface Configuration
- 37 Introduction to Command-Line Interface (CLI)
- 37 Accessing the CLI
- 38 Web Browser Configuration
- 38 Preparing for Web Configuration
- 38 System Login
- 40 Log In
- 40 Recommended Practices
- 40 Changing Default Password
- 41 Monitoring
- 41 Device Information
- 42 Logging Message
- 43 Port Monitoring
- 44 Link Aggregation
- 45 LLDP Statistics
- 46 IGMP Statistics
- 48 System
- 48 IP Settings
- 48 IPv6 Settings
- 49 System Time
- 50 Network Port
- 51 L2 Switching
- 51 Port Configuration
- 52 Port Mirror
- 53 Link Aggregation
- 56 802.1Q VLAN
- 59 Q-in-Q
- 62 802.3az EEE
- 63 Multicast
- 67 Jumbo Frame
- 68 4.5.10 Spanning Tree
- 73 4.5.11 X-Ring Elite
- 74 4.5.12 X-Ring Pro
- 75 4.5.13 Loopback Detection
- 77 RL3 Switching
- 77 SNAT (Source NAT)
- 78 DNAT (Destination NAT)
- 79 Routing
- 79 MAC Address Table
- 79 Static MAC
- 80 MAC Aging Time
- 80 Dynamic Forwarding Table
- 81 Security
- 81 Storm Control
- 83 Port Security
- 83 Protected Ports
- 84 DoS Prevention
- 86 Applications
- 88 802.1x
- 89 IP Security
- 90 General
- 96 QoS Basic Mode
- 97 Rate Limit
- 99 Management
- 99 4.10.1 LLDP
- 102 4.10.2 SNMP
- 104 4.10.3 TCP Modbus Settings
- 105 4.10.4 DHCP Server
- 110 4.10.5 SMTP Client
- 113 4.10.6 RMON
- 116 Diagnostics
- 116 4.11.1 Cable Diagnostics
- 117 4.11.2 Ping Test
- 118 4.11.3 IPv6 Ping Test
- 119 4.11.4 System Log
- 121 4.11.5 DDM
- 122 4.11.6 LED Indication
- 123 Tools
- 123 4.12.1 Backup Manager
- 124 4.12.2 Upgrade Manager
- 124 4.12.3 Dual Image
- 125 4.12.4 Save Configuration
- 125 4.12.5 User Account
- 126 4.12.6 Reset System
- 126 4.12.7 Reboot Device
- 126 Modbus/TCP Mapping
- 126 4.13.1 Modbus/TCP Mapping Table
- 147 Troubleshooting