advertisement
P R O G R A M M I N G t t eset output eset output
OPTION No
P61E
Ta mper to R
Ta mper to Strobe output
Tamper to Sonaler Ta mper to Siren output
KP P anic to R
KP P KP P
1E 2E 3E 4E 5E 6E 7E 8E
KP P
DESCRIPTION
Tamper & Panic alarms mapping ON ON ON ON ON ON ON ON anic to Siren output
ON = Factory default setting.
P61E 1E–4E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
1E–4E, ON: Tamper alarm triggers all outputs
NOTES:
• A Tamper Alarm can be caused by the
TAMP input or by removing the the J1 link.
P61E 5E–8E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
5E–8E, ON: Panic alarm triggers all outputs
NOTES:
• A Keypad Panic Alarm can be caused by the PANIC keys on the keypad (* E or ** together, depending on Option P64E6E).
TAMPER ALARM / OUTPUT MAPPING
This option selects which outputs will trigger when a Tamper Alarm occurs.
PROGRAMMING SEQUENCE:
P61E 1E–4E toggles the options ON and OFF
P61E 1E: Tamper Alarm to Reset output
P61E 2E: Tamper Alarm to Strobe output
P61E 3E: Tamper Alarm to Keypad Sonalert output
P61E 4E: Tamper Alarm to Siren output
KEYPAD PANIC ALARM / OUTPUT MAPPING
This option selects which outputs will trigger when a Keypad Panic alarm occurs.
PROGRAMMING SEQUENCE:
P61E 5E–8E toggles the options ON and OFF
P61E 5E: Keypad Panic Alarm to Reset output
P61E 6E: Keypad Panic Alarm to Strobe output
P61E 7E: Keypad Panic Alarm to Keypad Sonalert output
P61E 8E: Keypad Panic Alarm to Siren output
26
NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Introduction
- 4 Features
- 4 Specifications
- 5 Packing list
- 5 Installation procedures
- 6 CONNECTION DIAGRAM
- 7 Wiring examples
- 10 Keypad
- 11 OPERATION SUMMARY
- 12 Quick start Programming
- 13 How to enter Program Mode
- 13 Program mode levels
- 14 USER CODES
- 15 Timers
- 16 Vibration Sensitivity
- 19 Zone Assignment
- 21 AREA PARTITIONING
- 23 Zone To Output Mapping
- 25 Various Options
- 26 Tamper/Keypad Panic Output Mapping
- 27 System Operation Shortcuts
- 28 MONITOR MODE OUTPUT MAPPING
- 28 Day mode output mapping
- 29 Miscellaneous Options
- 31 SUPERVISED RADIO ZONES
- 31 Supervision time
- 33 Radio Supervision Alerts
- 35 Misc. options
- 38 Telephone Numbers
- 38 Account Number
- 39 Telephone Number 3 – Test Calls
- 39 Telephone Number 4 – Callback
- 39 Follow me Telephone Number
- 40 Report zone alarms
- 40 Report zone restorals
- 40 Report multiple zone alarms
- 40 Account No.2 zones
- 41 Report Miscellaneous alarms
- 41 Report Miscellaneous Restorals
- 41 Restoral Reporting options
- 42 Test Call Interval
- 42 Time before Next test call
- 42 Dialling Method
- 43 Disable Dialler
- 43 Contact ID format
- 43 Audible DTMF format
- 43 Audible Pulse format
- 44 Contact ID Reporting Codes
- 45 Alternate Dialling
- 45 Check for dial tone
- 45 Number of Dialling Attempts
- 46 Area1 open/close reports
- 46 Area2 open/close reports
- 46 Siren Chirp on kiss-off
- 46 Strobe Flash on kiss-off
- 47 Forced Opening Report
- 47 Delay Closing Report
- 47 Manual Exclude Report
- 47 Auto Exclude Report
- 48 Enable Test Calls
- 48 Mains Report Delay
- 48 Listen-in to dialler
- 49 Swinger Shutdown
- 49 Line Fault Monitor
- 49 Line Fault to AUX
- 50 Remote access
- 50 Direct Connect
- 51 Remote access options
- 52 Required Rings
- 53 Clear Radio Devices
- 53 Clear Memory
- 53 Clear Panel Options
- 53 Clear User Codes
- 54 Radio Quick Start
- 54 Ness Radio Interface
- 54 Signal strength meter
- 55 Radio Devices, Operation
- 55 Radio Supervision, Defined
- 56 Radio Device Programming
- 57 Radio Key Programming
- 58 Audible Monitoring Operation
- 59 Remote Operation by Telephone
- 60 Ness Accessories
- 61 Wireless Products
- 62 PROGRAMMING OPTIONS SUMMARY
- 63 Installation Record