advertisement
P83E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
84 (=168hrs =7 days)
NOTES:
• Enter a value from 1 to 99
• RELATED OPTIONS:
P89E 1E Enable Test Calls
P84E Time Before Next Test Call
P84E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
6 (=12hrs)
NOTES:
• Enter a value from 1 to 99
• If Test Calls are to start immediately, then the value is set to 0.
• The Time Before Next Test Call is constantly updated. When viewed, the current value will be displayed (not the initially entered value).
• RELATED OPTIONS:
P89E 1E Enable Test Calls
P83E Test Call interval
P R O G R A M M I N G
OPTION No
P83E
P84E
DESCRIPTION
Test Call Interval
Time Before Next Test Call
DEFAULT
84
6
NOTE x2 = 168hrs (7 days) x2 = 12hrs
TEST CALL INTERVAL
Test calls to the Central Station can be sent at intervals between 2 and 198 hours in 2 hour increments.
Programmable from 2 to 198 Hours. Enter a value between 1 and 99. (This is automatically multiplied by 2).
Test Calls must be enabled by option P89E 1E.
PROGRAMMING SEQUENCE:
P83E existing Test Call Interval time is displayed
[ENTER NEW TIME] E new Test Call Interval time is displayed
EXAMPLE: To program daily test calls:
P83E12E
TIME BEFORE NEXT TEST CALL
This option sets the time before the next Test Call and is used to set the preferred time for Test Calls. Programmable from 2 to 198 Hours. Enter a value between 1 and 99. (This is automatically multiplied by 2).
EXAMPLES:
A/ New Installation: Set the time before the first test call.
E.g., If you are programming the panel at 5pm and you want test calls to be sent at 1am. Enter P84E 4E (4 x 2 =8hrs. Therefore 5pm + 8hrs =1am).
B/ Existing Installation: To reset the time that test calls are sent.
E.g., Our example panel is sending test calls at 1am and you want to change it to 2am. If you are programming the panel at 6pm, enter P84E 4E (4 x 2
=8hrs. Therefore 6pm + 8hrs =2am).
PROGRAMMING SEQUENCE:
P84E existing Time Before Next Test Call is displayed (See note 3)
[ENTER NEW TIME] E new Time Before Next Test Call is displayed s
P85E 1E–3E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
1E, ON: Auto Dialling Method
NOTES:
• Only one option is allowed to be ON
42
OPTION No DESCRIPTION
P85E Dialling Method
Auto dialling methodPULSE Dialling alway .
.
.
.
1E 2E 3E 4E 5E 6E 7E 8E
ON
ON = Factory default setting.
DIALLING METHOD
The dial format is determined by the detected Dial Tone. By default, if no dial tone is detected after looping the line then the dialler will attempt to dial regardless alternating between PULSE (Decadic) first and then DTMF dialling.
PROGRAMMING SEQUENCE:
P85E 1E–3E turns the option ON
P85E 1E: Auto Dialling (PULSE or DTMF)
P85E 2E: Pulse Dialling always
P85E 3E: DTMF Dialling always
NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Introduction
- 4 Features
- 4 Specifications
- 5 Packing list
- 5 Installation procedures
- 6 CONNECTION DIAGRAM
- 7 Wiring examples
- 10 Keypad
- 11 OPERATION SUMMARY
- 12 Quick start Programming
- 13 How to enter Program Mode
- 13 Program mode levels
- 14 USER CODES
- 15 Timers
- 16 Vibration Sensitivity
- 19 Zone Assignment
- 21 AREA PARTITIONING
- 23 Zone To Output Mapping
- 25 Various Options
- 26 Tamper/Keypad Panic Output Mapping
- 27 System Operation Shortcuts
- 28 MONITOR MODE OUTPUT MAPPING
- 28 Day mode output mapping
- 29 Miscellaneous Options
- 31 SUPERVISED RADIO ZONES
- 31 Supervision time
- 33 Radio Supervision Alerts
- 35 Misc. options
- 38 Telephone Numbers
- 38 Account Number
- 39 Telephone Number 3 – Test Calls
- 39 Telephone Number 4 – Callback
- 39 Follow me Telephone Number
- 40 Report zone alarms
- 40 Report zone restorals
- 40 Report multiple zone alarms
- 40 Account No.2 zones
- 41 Report Miscellaneous alarms
- 41 Report Miscellaneous Restorals
- 41 Restoral Reporting options
- 42 Test Call Interval
- 42 Time before Next test call
- 42 Dialling Method
- 43 Disable Dialler
- 43 Contact ID format
- 43 Audible DTMF format
- 43 Audible Pulse format
- 44 Contact ID Reporting Codes
- 45 Alternate Dialling
- 45 Check for dial tone
- 45 Number of Dialling Attempts
- 46 Area1 open/close reports
- 46 Area2 open/close reports
- 46 Siren Chirp on kiss-off
- 46 Strobe Flash on kiss-off
- 47 Forced Opening Report
- 47 Delay Closing Report
- 47 Manual Exclude Report
- 47 Auto Exclude Report
- 48 Enable Test Calls
- 48 Mains Report Delay
- 48 Listen-in to dialler
- 49 Swinger Shutdown
- 49 Line Fault Monitor
- 49 Line Fault to AUX
- 50 Remote access
- 50 Direct Connect
- 51 Remote access options
- 52 Required Rings
- 53 Clear Radio Devices
- 53 Clear Memory
- 53 Clear Panel Options
- 53 Clear User Codes
- 54 Radio Quick Start
- 54 Ness Radio Interface
- 54 Signal strength meter
- 55 Radio Devices, Operation
- 55 Radio Supervision, Defined
- 56 Radio Device Programming
- 57 Radio Key Programming
- 58 Audible Monitoring Operation
- 59 Remote Operation by Telephone
- 60 Ness Accessories
- 61 Wireless Products
- 62 PROGRAMMING OPTIONS SUMMARY
- 63 Installation Record