D8 V4 Installers Manual (rev 4.5)

N E S S R A D I O

P09E, P10E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

No Radio Codes

NOTES:

• All User Codes can be Radio Codes except User Code 1 (Master Code) which is always a Keypad Code.

• Each User Code 2–15 can be either a

Radio Code or a Keypad Code (not both).

• Radio Key programming is done by

‘learning’ the code by radio.

• Radio Codes can only be deleted by keypad in the case of a lost Radio Key.

• Radio Keys are allocated to User Codes, so that Open/Close reports are identified by user number when the control panel is base station monitored. (If Open/Close reports are enabled)

• Radio Codes cannot be made Arm Only

• TIP: When adding Radio Keys, start at e.g., User Code 9. This will keep codes 1 to 8 free for use as Keypad Codes.

• RELATED OPTIONS:

P01E–P08E Programming Radio Devices

100–664 Radio Key

100–001

Radio Keypad

ASSIGN RADIO CODES

User

Codes

* 2 3 4 5 6 7 8

P09E User Codes 2-8

*

Note: User Code 1 is always a keypad code.

User

Codes

9 10 11 12 13 14 15

P10E User Codes 9-15

RADIO CODES

Each of the 15 User Codes, except for the Master Code, can be programmed to be Radio Codes. This allows up to 14 Ness Radio Keys to be used for Arming and Disarming of the panel. The Ness RKP Radio Keypad can also be used with the D8, (see the RKP installer manual). The optional 100–200 Ness Radio

Interface is required for radio operation.

PROGRAMMING RADIO KEYS

Radio Keys can be assigned to take the place of User Codes 2 to 15.

(User Code 1 is always a Keypad code.)

PROGRAMMING SEQUENCE:

➊

At option P09E

➋

Use P12E

The User Code selected must already be assigned as a Radio Code by options P09E or P10E

➌

Press 1E

The READY light will turn ON to indicate that the User Code is ready to accept the Radio Key.

If a code is already programmed the READY light will not turn on and a warning beep will sound. To clear the code, press 0E, then go back to step 3. (0E clears any Keypad Codes and Radio Keys).

➍

Press the OFF button on the Radio Key to be programmed

If the Radio Key is accepted, the READY light will turn off and 3 beeps will sound.

If the READY light stays on and a warning beep sounds, the Radio Key is already assigned to another

User Code and must be cleared from that User Code first.

➊

P10E 1E Enables User Code 9 as a radio code

➋

P19E 1E Selects ‘learn’ mode for User Code 9

➌

Press the OFF button on the Radio Key

DELETING A RADIO CODE:

➊

Use P12E

➋

Press 0E 3 beeps will sound

CODE TABLE

CODE

User Code 1

User Code 2

User Code 3

User Code 4

User Code 5

User Code 6

User Code 7

User Code 8

User Code 9

User Code 10

User Code 11

User Code 12

User Code 13

User Code 14

User Code 15

Installer Code

OPTION No

P21E

P22E

P23E

P24E

P25E

P99E

P11E

P12E

P13E

P14E

P15E

P16E

P17E

P18E

P19E

P20E

DESCRIPTION

Master Code

Installer Code

FACTORY

DEFAULT

123

2E

3E

4E

5E

6E

7E

3E

4E

5E

6E

7E

8E

1E

ENABLE AS A

RADIO CODE

(Keypad Code only)

2E

P09E

P10E

000000

NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL

57