D8 V4 Installers Manual (rev 4.5)

P68E 5E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Radio Key siren warning disabled

NOTES:

•

P R O G R A M M I N G

RADIO KEY ARMING, UNSEALED ZONE WARNING

Setting this option ON allows a 2 second SIREN warning if there is an unsealed zone in an Area Armed by a Radio Key.

PROGRAMMING SEQUENCE:

P68E 5E toggles the option ON and OFF

P68E 5E OFF: Radio Key arming, siren warning disabled

P68E 5E ON: Radio Key arming, siren warning enabled

P68E 6E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: No 24hr Fire siren sound

NOTES:

• The keypad key sequence for FIRE (3 E) always outputs the FIRE siren sound

P68E 7E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: 4th button for AUX1 disabled

NOTES:

• RELATED OPTIONS:

P68E 3E & 4E Radio Key Panic to AUX1

24HR ZONE FIRE SIREN SOUND

This option changes the siren sound when a 24hr zone is triggered.

PROGRAMMING SEQUENCE:

P68E 6E toggles the option ON and OFF

P68E 6E OFF: Fire siren sound disabled

P68E 6E ON: Fire siren sound enabled

4th BUTTON RADIO KEY FOR AUX1

Ness 4 Button Radio Key only – this option changes P68E 3E and 4E to work with the 4th Button of a 4 Button Radio Key instead of the PANIC button.

PROGRAMMING SEQUENCE:

P68E 7E toggles the option ON and OFF

P68E 7E OFF: 4th button Radio Key for AUX1 disabled

P68E 7E ON: 4th button Radio Key for AUX1 enabled

P68E 8E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Quiet Chirps disabled

NOTES:

• RELATED OPTIONS:

P64E 4E Arm/Disarm Chirps

QUIET CHIRPS ON ARM/DISARM

This quietens the siren chirps that are made whenever keyswitch or radio key

Arming or Disarming is used.

(Arm/Disarm Chirps must be enabled at P64E 4E).

PROGRAMMING SEQUENCE:

P68E 8E toggles the option ON and OFF

P68E 8E OFF: Quiet Chirps disabled

P68E 8E ON: Quiet Chirps enabled

NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL

35

P69E 1E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: ARM1 output toggles

NOTES:

• This is useful as a Smoke Detector reset output with an optional external relay.

• RELATED OPTIONS:

P60E 8E Delay ARM1/ARM2 outputs

P69E 2E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: ARM2 output toggles

NOTES:

• This is useful as a Smoke Detector reset output with an optional external relay.

• RELATED OPTIONS:

P60E 8E Delay ARM1/ARM2 outputs

P R O G R A M M I N G

OPTION No DESCRIPTION

P69E Miscellaneous options 2 ming ming ey Monitor Ar

ARM1 pulse outputARM2 pulse outputQuiet Monitor siren6 beeps on Ar R adio K

.

.

1E 2E 3E 4E 5E 6E 7E 8E

.

ON = Factory default setting.

ARM1 PULSE OUTPUT

This option selects the ARM1 output to pulse on for 2 seconds whenever arming or disarming of Area1.

(The ARM1 output normally toggles when arming/disarming).

Note also that when Arming with the P60E 8E option selected that the pulse will occur at the end of Exit Time.

PROGRAMMING SEQUENCE:

P69E 1E toggles the option ON and OFF

P69E 1E OFF: ARM1 output toggles

P69E 1E ON: ARM1 output pulses

ARM2 PULSE OUTPUT

This option selects the ARM2 output to pulse on for 2 seconds whenever Arming or Disarming of Area2.

(The ARM2 output normally toggles when arming/disarming).

Note also that when Arming with the P60E 8E option selected that the pulse will occur at the end of Exit Time.

PROGRAMMING SEQUENCE:

P69E 2E toggles the option ON and OFF

P69E 2E OFF: ARM2 output toggles

P69E 2E ON: ARM2 output pulses

P69E 3E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Normal siren sound in Monitor Mode

NOTES:

• This does not affect the RESET output

QUIET MONITOR SIREN

This option selects the ‘Quiet Siren’ sound in Monitor Mode.

The Quiet Siren sound is a continuous “beep beep beep” sound rather than the normal siren sound.

PROGRAMMING SEQUENCE:

P69E 3E toggles the option ON and OFF

P69E 3E OFF: Normal siren sound in Monitor Mode

P69E 3E ON: Quiet Siren sound in Monitor Mode

36

NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL

P69E 4E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Keypad gives 3 beeps on Arming

NOTES:

• The keypad beeps on Arm/Disarm when

Arming/Disarming by keypad, keyswitch or by Radio Key

P R O G R A M M I N G

6 BEEPS ON ARMING

Normally the keypad/s onboard SONALERT gives 3 beeps when the D8 is

Armed. Turning this option ON will give 6 keypad beeps when Arming.

PROGRAMMING SEQUENCE:

P69E 4E toggles the option ON and OFF

P69E 4E OFF: Keypad gives 3 beeps on Arming

P69E 4E ON: Keypad gives 6 beeps on Arming

P69E 5E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Radio Keys cannot Arm Monitor Mode

NOTES:

• Radio Key Monitor Arming will work only if one or more zones have been programmed as Monitor Zones (P51E).

• When using a Radio Keypad to Monitor arm, ensure that the ARM ONLY option is

OFF for the USER CODE on the panel.

Otherwise further MONITOR E keypresses on the Radio keypad could

AREA arm the panel.

RADIO KEY MONITOR ARMING

Setting this option on allows MONITOR Mode arming by Radio Key.

PROGRAMMING SEQUENCE:

P69E 5E toggles the option ON and OFF

P69E 5E OFF: Radio Key Monitor Mode Arming disabled

P69E 5E ON: Radio Key Monitor Mode Arming enabled

OPERATION:

Panel version 4 - Press the Radio Key OFF button twice within 4 seconds.

Panel version 4.5 - Press the Radio Key OFF button twice within 4 seconds.

or....

- Press the Radio Key ON button twice within 5 seconds.

NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL

37