advertisement
P91E
PROGRAM MODE LEVEL:
Installer, Remote by PC
FACTORY DEFAULT:
1
NOTES:
• RELATED OPTIONS:
P90E 1E to 8E (All Remote Access options)
P R O G R A M M I N G
OPTION No
P91E
DESCRIPTION
Required Rings to answer
DEFAULT
1
NOTE
REQUIRED RINGS
Sets the number of double-rings before an incoming call is answered. This is used for Remote Access.
Programmable from 1 to 16 rings. Enter a value between 1 and 16.
See below for a detailed description.
PROGRAMMING SEQUENCE:
P91E existing Required Rings value is displayed
[ENTER NEW VALUE] E new Required Rings value is displayed
EXAMPLE: To make Required Rings = 3:
P91E3E
P66666666E
PROGRAM MODE LEVEL:
User Program Mode
FACTORY DEFAULT:
[not applicable]
P77777777E
PROGRAM MODE LEVEL:
Installer, User Program Mode
FACTORY DEFAULT:
[not applicable]
P88888888E
PROGRAM MODE LEVEL:
Installer, User Program Mode
FACTORY DEFAULT:
[not applicable]
P99999999E
PROGRAM MODE LEVEL:
Installer, User Program Mode
FACTORY DEFAULT:
[not applicable]
SEND DIALLER TEST REPORT
Send a Dialler Test Report in USER PROGRAM MODE. Obviously, at least one telephone number must be programmed (P70E).
PROGRAMMING SEQUENCE:
P66666666E (eight 6’s) Triggers dialler and sends test report to Central Station
SIREN TEST
Turn the Siren, Reset and Strobe Outputs On. Pressing P E will stop the Siren Test (and also exits Program Mode).
PROGRAMMING SEQUENCE:
P77777777E (eight 7’s) Triggers Siren, Reset, Strobe
PANEL RESET
This function resets the microprocessor. The effect is the same as powering down and powering up again.
PROGRAMMING SEQUENCE:
P88888888E (eight 8’s) Panel Reset
PANEL SOFTWARE VERSION
This function displays the panel software version when in program mode. Displayed in decimal format by the zone LEDs.
Example, version 4.5 is displayed by flashing 4 followed by 5.
PROGRAMMING SEQUENCE:
P999999999E (eight 9’s) Displays software version
52
NESS D8 (V4.5) CONTROL PANEL – INSTALLER MANUAL
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Introduction
- 4 Features
- 4 Specifications
- 5 Packing list
- 5 Installation procedures
- 6 CONNECTION DIAGRAM
- 7 Wiring examples
- 10 Keypad
- 11 OPERATION SUMMARY
- 12 Quick start Programming
- 13 How to enter Program Mode
- 13 Program mode levels
- 14 USER CODES
- 15 Timers
- 16 Vibration Sensitivity
- 19 Zone Assignment
- 21 AREA PARTITIONING
- 23 Zone To Output Mapping
- 25 Various Options
- 26 Tamper/Keypad Panic Output Mapping
- 27 System Operation Shortcuts
- 28 MONITOR MODE OUTPUT MAPPING
- 28 Day mode output mapping
- 29 Miscellaneous Options
- 31 SUPERVISED RADIO ZONES
- 31 Supervision time
- 33 Radio Supervision Alerts
- 35 Misc. options
- 38 Telephone Numbers
- 38 Account Number
- 39 Telephone Number 3 – Test Calls
- 39 Telephone Number 4 – Callback
- 39 Follow me Telephone Number
- 40 Report zone alarms
- 40 Report zone restorals
- 40 Report multiple zone alarms
- 40 Account No.2 zones
- 41 Report Miscellaneous alarms
- 41 Report Miscellaneous Restorals
- 41 Restoral Reporting options
- 42 Test Call Interval
- 42 Time before Next test call
- 42 Dialling Method
- 43 Disable Dialler
- 43 Contact ID format
- 43 Audible DTMF format
- 43 Audible Pulse format
- 44 Contact ID Reporting Codes
- 45 Alternate Dialling
- 45 Check for dial tone
- 45 Number of Dialling Attempts
- 46 Area1 open/close reports
- 46 Area2 open/close reports
- 46 Siren Chirp on kiss-off
- 46 Strobe Flash on kiss-off
- 47 Forced Opening Report
- 47 Delay Closing Report
- 47 Manual Exclude Report
- 47 Auto Exclude Report
- 48 Enable Test Calls
- 48 Mains Report Delay
- 48 Listen-in to dialler
- 49 Swinger Shutdown
- 49 Line Fault Monitor
- 49 Line Fault to AUX
- 50 Remote access
- 50 Direct Connect
- 51 Remote access options
- 52 Required Rings
- 53 Clear Radio Devices
- 53 Clear Memory
- 53 Clear Panel Options
- 53 Clear User Codes
- 54 Radio Quick Start
- 54 Ness Radio Interface
- 54 Signal strength meter
- 55 Radio Devices, Operation
- 55 Radio Supervision, Defined
- 56 Radio Device Programming
- 57 Radio Key Programming
- 58 Audible Monitoring Operation
- 59 Remote Operation by Telephone
- 60 Ness Accessories
- 61 Wireless Products
- 62 PROGRAMMING OPTIONS SUMMARY
- 63 Installation Record