Diagnostic. Billion Electric QI3BIL-7401VGPR4

Diagnostic

It tests the connection to computer(s) which is connected to the LAN ports and also the WAN Internet connection. If PING www.google.com is shown FAIL and the rest is PASS, you ought to check your

PC’s DNS setting is correct.

27

Quick Start

1. Click Quick Start. If your ADSL line is not ready, you need to check your ADSL line has been set or not.

2. If your ADSL line is ready, the screen appears ADSL Line is Ready. Choose Auto radio button and click Apply. It will automatically scan the recommended mode for you. Manually mode makes you to set the ADSL line by manual. (If you choose Manually, you will directly go to step

5.)

3. The list below has different mode applied for your choice. Choose 0/33/PPPoE(Recommended) and click Apply.

4. Please enter “Username” and “Password” as supplied by your ISP (Internet Service Provider) and click Apply to continue.

28

Profile Port: Select the connection mode. There is ADSL .

Protocol : Select the protocol mode. The default mode is PPPoE.

VPI/VCI : Enter the VPI and VCI information provided by your ISP.

Username : Enter the username provided by your ISP.

Password : Enter the password provided by your ISP.

Service Name : This item is for identification purposes. If it is required, your ISP provides you the information.

Authentication Protocol : Default is Auto.

Your ISP advises on using Chap or Pap.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

IP Address: Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

Obtain DNS: A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. DNS helps to find the IP address for the specific domain name. Check the checkbox to obtain DNS automatically.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS

29

5. Configure the Wireless LAN setting.

WLAN Service: Default setting is set to Enable. If you want to use wireless, both 802.11g and

802.11b device in your network, you can select Enable.

ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network.

ESSID Broadcast : It is function in which transmits its ESSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Default setting is Enable.

L Enable: When Enable is selected, you can allow anybody with a wireless client to be able to locate the Access Point (AP) of your router.

L Disable: Select Disable if you do not want broadcast your ESSID. When select Disable, no one will be able to locate the Access Point (AP) of your router.

Regulation Domain: There are seven Regulation Domains for you to choose from, including

North America (N.America), Europe, France, etc. The Channel ID will be different based on this setting.

Channel ID: Select the ID channel that you would like to use.

Security Mode: You can disable or enable with WPA or WEP for protecting wireless network. The default mode of wireless security is Disable .

6. Set up VoIP.

30

SIP: To use VoIP SIP as VoIP call signaling protocol. Default is set to Disable.

Region: This selection is a drop-down box, which allows user to select the country for which the

VoIP device must work. When a country is selected, the country parameters are automatically loaded.

SIP Service Provider: This section allows you to select the service provider. When the selection is done, respective parameters below are automatically displayed.

Phone Number: This parameter holds the registration ID of the user within the VoIP SIP registrar.

Username: If the username is same as the Phone Number, leave it blank. Otherwise, fill in the space with your username given by your VoIP provider.

Password: This parameter holds the password used for authentication within VoIP SIP registrar.

Display Name: This parameter will be appeared on the Caller ID.

Remark:

For products available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

31

7. Wait for the configuration.

8. When ADSL is synchronic, it will appear “check”.

32

Configuration

When you click this item, the column will expand to display the sub-items that will allow you to further configure your ADSL router.

LAN, WAN, System, Firewall, VoIP, QoS, Virtual Server, Wake on LAN, Time Schedule and

Advanced

The function of each configuration sub-item is described in the following sections.

33